Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Dielectric Properties of (1−x)CaTiO3–xCa(Zn1/3Nb2/3)O3 Ceramic System at Microwave Frequency

The microwave dielectric properties of the (1− x )CaTiO₃– x Ca(Zn_1/3Nb_2/3)O₃ ceramic system have been investigated. The ceramic samples sintered at 1300°–1450°C for 4 h in air exhibit orthorhombic pervoskite and form a complete solid solution for different x value. When the x value increased from 0.2 to 0.8, the permittivity ɛ_r decreased from 115 to 42, the unloaded quality factor Q × f increased from 5030 to 13 030 GHz, and the temperature coefficient τ_f decreased from 336 to −28 ppm/°C. When x =0.7, the best combination of dielectric properties, a near zero temperature coefficient of resonant frequency of τ_f∼−6 ppm/°C, Q × f ∼10 860 GHz and ɛ_r∼51 is obtained.     

Microstructure and Microwave Dielectric Properties of (1−x)Ca(Mg1/3Ta2/3)O3/xCaTiO3 Ceramics

Dense (1− x )Ca(Mg_1/3Ta_2/3)O₃/ x CaTiO₃ ceramics (0.1≤ x ≤0.9) were prepared by a solid-state reaction process. The crystal structures and microstructures were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Single-phase solid solutions were obtained in the entire composition range. Long-range 1:2 ordering of B-site cations and oxygen octahedra tilting lead to the monoclinic symmetry with space group P 2₁/ c for x =0.1. For x above 0.1, the long-range ordering was destroyed and the crystal structure became the orthorhombic with space group Pbnm . The microwave dielectric properties showed a strong dependence on the composition and microstructure. The dielectric constant and temperature coefficient of resonant frequency increased nonlinearly as the CaTiO₃ content increased while the Qf values decreased approximately linearly. Good combination of microwave dielectric properties was obtained at x =0.45, where ɛ_r=45.1, Qf =34 800 GHz, and τ_f=17.4 ppm/°C.     

Low-Loss Microwave Dielectrics Using Mg2(Ti1−xSnx)O4 (x=0.01–0.09) Solid Solution

Low-loss ceramics having the chemical formula Mg₂(Ti_{1− x} Sn _x )O₄ for x ranging from 0.01 to 0.09 have been prepared by the conventional mixed oxide route and their microwave dielectric properties have been investigated. X-ray powder diffraction patterns indicate the corundum-structured solid solutions for the prepared compounds. In addition, lattice parameters, which linearly increase from 8.4414 to 8.4441 Å with the rise of x from 0.01 to 0.09, also confirm the forming of solid solutions. By increasing x from 0.01 to 0.05, the Q × f of the specimen can be tremendously boosted from 173 000 GHz to a maximum 318 000 GHz. A fine combination of microwave dielectric properties (ɛ_r∼15.57, Q × f ∼318 000 GHz at 10.8 GHz, τ_f∼−45.1 ppm/°C) was achieved for Mg₂(Ti_0.95Sn_0.05)O₄ ceramics sintered at 1390°C for 4 h. Ilmenite-structured Mg(Ti_0.95Sn_0.05)O₃ (ɛ_r∼16.67, Q × f ∼275 000 GHz at 10.3 GHz, τ_f∼−53.2 ppm/°C) was detected as a second phase. The presence of the second phase, however, would cause no significant variation in the dielectric properties of the specimen, because the second phase properties are very similar to the primary phase. These unique properties, in particular, low ɛ_r and high Q × f , can be utilized as a very promising dielectric material for ultra-high-frequency applications.     

Microwave Dielectric Properties of CaTiO3-Ca(Al1/2Ta1/2)O3 Ceramics

The microwave dielectric properties of CaTi_1-χ(Al_1/2Ta_1/2)_cHO₃ solid solutions (0.3 ≤χ≤ 0.5) have been investigated. The ceramic samples had perovskite structures similar to CaTiO₃. The partial substitution of Ti₄₊ by a coupled Al₃₊/Ta_s+ permitted improvement of the quality factor Q . The dielectric constant (τ_r) and temperature coefficient of resonant frequency (τ_r) decrease rapidly with an increase of χ. A new high-quality microwave dielectric material was found at χ= 0.46 with σ_r= 46.5, Q f = 27300 GHz, and π_f= 0 ppm/°C. The relationship between microstructures and dielectric properties is presented.     

Structural and Dielectric Characteristics in a Ca(Mg1/3Nb2/3)O3–CaZrO3 System

This study investigates the effect of CaZrO₃ (CZ) substitution on the evolution of an ordered structure in a Ca(Mg_1/3Nb_2/3)O₃ (CMN) system using Raman spectroscopy, X-ray diffractometry, and transmission electron microscopy. It indicates that a (1− x ) CMN−( x )CZ solid solution has the 1:2 and 1:1 ordered structure distorted by the antiphase, the inphase tilting of oxygen octahedra, and the antiparallel shift of A-site cation. A distinct correlation is noted between the transition of the ordered structure and microwave dielectric properties. The differences in ɛ_r and τ_f are attributed exclusively to the differences in the type of cation arrangement. The structure with the 1:2 ordering exhibits a lower relative permittivity and a more negative τ_f than the structure with the 1:1 ordering. The increased fraction of compressed Nb–O bond in the 1:2 ordered structure associated with a large NbO₆ octahedral distortion is correlated with a decrease in relative permittivity and change of τ_f toward more negative values. Simultaneously, the substitution of the Zr⁴⁺ ion causes a linear increase in polarizability, and it also results in an increase in the relative permittivity.     

Microwave Dielectric Properties of A-Site Modified Ba(Co0.7Zn0.3)1/3Nb2/3O3 by La3+

The sintering behavior, ordering state, and microwave dielectric properties of Ba_{1− x} La_{2 x /3}(Zn_0.3Co_0.7)_1/3Nb_2/3O₃ Ceramics (0≤ x ≤0.06) were investigated in this paper. The X-ray diffraction (XRD) results show that all samples exhibit a single perovskite phase except for the sample with x ≥0.03. The sinterability is slightly improved by La doping. The long range order (LRO) degree on B-site is greatly increased with the increase of x value up to x =0.015 and then slightly decreased with the further increase of x due to the increasing amount of second phases. The dielectric constant at microwave frequency decreases slightly with the increase of x when x <0.015 and increases slightly with further increasing x for the samples sintered at 1375°C/10 h. The Q × f value increases with x up to x =0.015 and then decreases with further increase of x , which is consistent with the variation trend of LRO degree. The τ_f value decreases slightly with the increase of x up to 0.006, then increases greatly with the further increase of x . An optimized dielectric properties of ɛ _r =34, Q × f =63 159, GHz and τ_f=5.21 ppm/°C were obtained for the x =0.01 sample sintered at 1425°C/10 h.     

The Effect of Dopants on the Dielectric Properties of Ba(B'1/2Ta1/2)O3 (B'=La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Y, Yb, and In) Microwave Ceramics

Low-loss dielectric ceramics based on Ba(B'_1/2Ta_1/2)O₃ (B'=La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Y, Yb, and In) complex perovskites have been prepared by the solid-state ceramic route. The dielectric properties (ɛ_r, Q _u, and τ_f) of the ceramics have been measured in the frequency range 4–6 GHz by the resonance method. The resonators have a relatively high dielectric constant and high quality factor. Most of the compounds have a low coefficient of temperature variation of the resonant frequencies. The microwave dielectric properties have been improved by the addition of dopants and by solid solution formation. The solid solution Ba[(Y_{1− x} Pr _x )_1/2Ta_1/2]O₃ has x =0.15, with ɛ_r=33.2, Q _u× f =51,500 GHz, and τ_f≈0. The microwave dielectric properties of Ba(B'_1/2Ta_1/2)O₃ ceramics are found to depend on the tolerance factor ( t ), ionic radius, and ionization energy.     

Effects of Ca/Ti Cosubstitution upon Microwave Dielectric Characteristics of CaSmAlO4 Ceramics

(Ca_{1+ x} Sm_{1− x} )(Al_{1− x} Ti _x )O₄ (0≤ x ≤0.4) ceramics were synthesized by solid-state reaction method and their microstructures and microwave dielectric properties were investigated. X-ray diffraction analysis and energy-dispersive X-ray analysis indicated that the matrix phase was a solid solution with a composition represented by the chemical formula (Ca_{1+ x} Sm_{1− x} ) (Al_{1− x} Ti _x )O₄ and minor amount of (Ca,Sm)(Al,Ti)O₃ secondary phase was detected. Ca/Ti cosubstitution could significantly improve the microwave dielectric characteristics of CaSmAlO₄ ceramics, and the excellent microwave dielectric characteristics were obtained in the modified ceramics as ɛ_r=19–23, Q × f =49 100–118 700 GHz, and τ_f=−15–15 ppm/°C.     

High Q Microwave Dielectric Ceramics in (Ni1−x Znx)Nb2O6 System

(Ni_{1− x} Zn _x )Nb₂O₆, 0≤ x ≤1.0, ceramics with >97% density were prepared by a conventional solid-state reaction, followed by sintering at 1200°–1300°C (depending on the value of x ). The XRD patterns of the sintered samples (0≤ x ≤1.0) revealed single-phase formation with a columbite ( Pbcn ) structure. The unit cell volume slightly increased with increasing Zn content ( x ). All the compositions showed high electrical resistivity (ρ_dc=1.6±0.3 × 10¹¹Ω·cm). The microwave (4–5 GHz) dielectric properties of (Ni_{1− x} Zn _x )Nb₂O₆ ceramics exhibited a significant dependence on the Zn content and to some extent on the morphology of the grains. As x was increased from 0 to 1, the average grain size monotonically increased from 7.6 to 21.2 μm and the microwave dielectric constant (ɛ'_r) increased from 23.6 to 26.1, while the quality factors ( Q _u× f ) increased from 18 900 to 103 730 GHz and the temperature coefficient of resonant frequency (τ_f) increased from −62 to −73 ppm/°C. In the present work, we report the highest observed values of Q _u× f =103 730 GHz, and ɛ'_r=26.1 for the ZnNb₂O₆-sintered ceramics.     

Contribution of Structure to Temperature Dependence of Resonant Frequency in the (1 −x)La(Zn1/2Ti1/2)O3·xATiO3 (A = Ca, Sr) System

The crystal structure and microwave dielectric properties of the (1 − x ) La(Zn_1/2Ti_1/2)O₃· x SrTiO₃ and (1 − x )La(Zn_1/2Ti_1/2)O₃· x CaTiO₃ system were investigated. X-ray powder diffraction showed that cation ordering disappeared at x > 0.3 for both systems. However, infrared spectra demonstrated that short-range cation ordering could exist at x = 0.4. Permittivity and the temperature coefficient of the resonant frequency (τ_f) of both systems exhibited nonmonotonic variations with composition. Both systems exhibited a τ_f of zero at the same composition of x = 0.5 although the τ_f of SrTiO₃ was about two times larger than that of CaTiO₃. The behavior of the permittivity and τ_f were described by the tilting of oxygen octahedra and cation ordering. The relation between τ_f and cation ordering of La(Zn_1/2Ti_1/2)O₃ was discussed in conjunction with the experimental results on metal halides. It is suggested that cation ordering induced a negative τ_f and suppressed the increase of permittivity for compositions between x = 0 to x = 0.5 for (1 − x )La(Zn_1/2Ti_1/2)O₃· x SrTiO₃ and (1 − x )La(Zn_1/2Ti_1/2)O₃· x CaTiO₃ systems.     

Low-Dielectric Loss Characteristics of Nd(Co1/2Ti1/2)O3 Ceramics at Microwave Frequencies

The microwave dielectric properties and the microstructures of Nd(Co_1/2Ti_1/2)O₃ (NCT) ceramics using starting powders of Nd₂O₃, CoO, and TiO₂ prepared by the conventional solid-state route have been researched. The dielectric constant values (ɛ_r) saturated at 24.8–27. Quality factor ( Q × f ) values of 37 900–140 000 (at 9 GHz) and the measured τ_f values ranging from −45 to −48 ppm/°C can be obtained when the sintering temperatures are in the range of 1410°–1500°C. The ɛ_r value of 27, the Q × f value of 140 000 (at 9 GHz) and the τ_f value of −46 ppm/°C were obtained for NCT ceramics sintered at 1440°C for 4 h. For applications of high selective microwave ceramic resonator, filter, and antenna, NCT is proposed as a suitable material candidate.     

Glass-Free Zn2Te3O8 Microwave Ceramic for LTCC Applications

A Zn₂Te₃O₈ ceramic was investigated as a promising dielectric material for low-temperature co-fired ceramics (LTCC) applications. The Zn₂Te₃O₈ ceramic was synthesized using the solid-state reaction method by sintering in the temperature range 540°–600°C. The structure and microstructure of the compounds were investigated using X-ray diffraction (XRD) and scanning electron microscopy methods. The dielectric properties of the ceramics were studied in the frequency range 4–6 GHz. The Zn₂Te₃O₈ ceramic has a dielectric constant (ɛ_r) of 16.2, a quality factor ( Q _u× f ) of 66 000 at 4.97 GHz, and a temperature coefficient of resonant frequency (τ_f) of −60 ppm/°C, respectively. Addition of 4 wt% TiO₂ improved the τ_f to −8.7 ppm/°C with an ɛ_r of 19.3 and a Q _u× f of 27 000 at 5.14 GHz when sintered at 650°C. The chemical reactivity of the Zn₂Te₃O₈ ceramic with Ag and Al metal electrodes was also investigated.     

Effect of Cation Substitution and Non-Stoichiometry on the Microwave Dielectric Properties of Sr(B'0.5Ta0.5)O3 [B'=Lanthanides] Perovskites

The Sr(B'_0.5Ta_0.5)O₃ ceramics where B'=La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Y, Er, and Yb have been prepared by the conventional solid-state ceramic route and their microwave dielectric properties have been investigated. The structure and microstructure of the ceramics have been characterized by X-ray diffraction and scanning electron microscope techniques. The relative permittiviy (ɛ_r) varies linearly with B'-site ionic radii, except for La, and the temperature coefficient of resonant frequency (τ_f) varies linearly with the tolerance factor. The Sr(B'_0.5Ta_0.5)O₃ ceramics have ɛ_r in the range 25.9–32, Q _u× f =4500–54 300 GHz, and τ_f=−79 to −42 ppm/°C. A slight deviation from stoichiometry affects the dielectric properties of these double perovskites. Partial substitution of Ba for Sr could tune the dielectric properties. Addition of rutile (TiO₂) lowered the sintering temperature and improved the dielectric properties of Sr(B'_0.5Ta_0.5)O₃ ceramics.     

Low-Loss Microwave Dielectric Ceramics Using (Mg1−xMnx)2TiO4 (x=0.02–0.1) Solid Solution

Composite ceramics in a solid solution of (Mg_{1− x} Mn _x )₂TiO₄ ( x =0.02–0.1) have been prepared by the mixed oxide route. Formation of the solid solution was confirmed by the X-ray diffraction, the EDX analysis, and the measured lattice parameters, which varied linearly from Mg₂TiO₄ ( a = b = c =8.4410 Å) to (Mg_0.9 Mn_0.1)₂TiO₄ ( a = b = c =8.4445 Å). The XRD analysis also confirmed the co-existence of a cubic-structured (Mg_{1− x} Mn _x )₂TiO₄ and an ilmenite-structured second phase (Mg_{1− x} Mn _x )TiO₃. The composition expected to have a maximum Q × f (276 200 GHz at 10.5 GHz) is (Mg_0.95Mn_0.05)₂TiO₄ with ɛ_r∼15.69 and τ_f∼−52.6 ppm/°C. The existence of the second phase, however, would lead to no significant variation in the dielectric properties of the specimen because it possesses compatible properties compared with that of the main phase.     

Microwave Dielectric Properties of Low-Fired ZnNb2O6 Ceramics with BiVO4 Addition

The BiVO₄ additive was found effective for low-temperature firing of ZnNb₂O₆ polycrystalline ceramics below 950°C in air without a serious degradation in their microwave dielectric properties. Dense BiVO₄-doped ZnNb₂O₆ samples of a relative sintered density over 95% could be prepared even at 925°C. An optimally processed specimen exhibited excellent microwave dielectric properties of Q · f = 55000 GHz, ɛ_r= 26, and τ_f=−57 ppm/°C. With increasing BiVO₄ addition up to 20 mol% relative to ZnNb₂O₆, while the quality factor Q · f was gradually decreased, the relative dielectric constant, ɛ_r, was linearly increased and the temperature coefficient of resonant frequency, τ_f, was slightly increased. The variations in Q · f and ɛ_r are surely attributable to the residual BiVO₄ in the ZnNb₂O₆ matrix. An unexpected slight increase in τ_f is probably due to the formation of the Bi(V,Nb)O₄-type solid solution.     

Structure and Microwave Dielectric Properties of Hexagonal Ba[Ti1−x(Ni1/2W1/2)x]O3 Ceramics

Microwave dielectric ceramics with the composition of Ba[Ti_{1− x} (Ni_1/2W_1/2) _x ]O₃ ( x =0.4–0.6) were prepared by a solid-state reaction method. The evolution of the crystalline phases was investigated by X-ray powder diffraction analysis. A cubic-to-hexagonal phase transition occurred between 1000° and 1300°C. The phase transition is irreversible; thus, the hexagonal phase remains stable at room temperature. The X-ray powder diffraction data for x =0.5 were refined using the Rietveld method. It was identified as a h -BaTiO₃-type hexagonal perovksite with the space group of P 6₃/ mmc . It also reveals that random occupancy of Ti⁴⁺ and W⁶⁺ ions occurs in the B-site substructures, whereas Ni²⁺ ions exclusively occupy the octahedral site in the corner-sharing octahedron. The dielectric properties of dense-sintered ceramics were characterized at microwave frequencies. With an increase in x from 0.4 to 0.6, the Q × f value increased from 26 700 to 42 000 GHz, whereas ɛ_r decreased from 29.8 to 20.0, and τ_f from +6.5 to −9.9 ppm/°C.     

Structure and Microwave Dielectric Characteristics of Ca1+xNd1−xAl1−xTixO4 Ceramics

CaNdAlO₄ microwave dielectric ceramics were modified by Ca/Ti co-substitution, and their dielectric characteristics were evaluated along with their structure and microstructures. Ca_{1+ x} Nd_{1− x} Al_{1− x} Ti _x O₄ ( x =0, 0.025, 0.05, 0.10, 0.15, 0.20) ceramics with the relative density of over 95% theoretical density were obtained by sintering at 1400°–1450°C in air for 3 h, where the K₂NiF₄-type solid solution single phase was determined from the compositions of x <0.20, while a small amount of CaTiO₃ secondary phase was detected for x =0.20. With Ca/Ti co-substitution in CaNdAlO₄ ceramics, the dielectric constant (ɛ_r) increased with increasing x , and the temperature coefficient of resonant frequency (τ_f) was adjusted from negative to positive, while the Q × f ₀ value increased significantly at first and reached an extreme value at x =0.025 and the maximum at x =0.15. The best combination of microwave dielectric characteristics were achieved at x =0.15 (ɛ_r=19.5, Q × f ₀=93 400 GHz, τ_f=−2 ppm/°C). The improvement of the Q × f ₀ value primarily originated from the reduced interlayer polarization with Ca/Ti co-substitution, while the decreased tolerance factor, the subsequent increased interlayer stress, and the appearance of CaTiO₃ secondary phase brought negative effects upon the Q × f ₀ value.     

Microwave Dielectric Properties of La6Mg4A2W2O24 [A=Ta and Nb] Ceramics

The microwave dielectric properties of two A-site-deficient perovskite-type ceramics in the La₆Mg₄A₂W₂O₂₄ [A=Ta and Nb] system were investigated. The compounds were synthesized by the solid-state ceramic route. The structure and microstructure were analyzed using X-ray diffraction and scanning electron microscopy techniques. The dielectric properties were measured in the microwave frequency range [4–6 GHz] by the resonance method. La₆Mg₄Ta₂W₂O₂₄ had Q _u× f =13 600 GHz, ɛ_r=25.2, and τ_f=−45 ppm/°C and La₆Mg₄Nb₂W₂O₂₄ had Q _u× f =16 400 GHz, ɛ_r=25.8, and τ_f=−56 ppm/°C.     

Dielectric Characteristics of Nd(Zn1/2Ti1/2)O3 Ceramics at Microwave Frequencies

The microwave dielectric properties and the microstructures of Nd(Zn_1/2Ti_1/2)O₃ (NZT) ceramics prepared by the conventional solid-state route have been studied. The prepared NZT exhibited a mixture of Zn and Ti showing 1:1 order in the B-site. The dielectric constant values (ɛ_r) saturated at 29.1–31.6. The quality factor ( Q × f ) values of 56 700–170 000 (at 8.5 GHz) can be obtained when the sintering temperatures are in the range of 1300°–1420°C. The temperature coefficient of resonant frequency τ_f was not sensitive to the sintering temperature. The ɛ _r value of 31.6, the Q × f value of 170 000 (at 8.5 GHz), and the τ_f value of −42 ppm/°C were obtained for NZT ceramics sintering at 1330°C for 4 h. For applications of high selective microwave ceramic resonators, filters, and antennas, NZT is proposed as a suitable material candidate.