Modeling and analysis of the induced signal detected in electrostatic ion beam trap for mass spectrometry

The induced image charge and image current acquired by a detector tube for mass analysis are simulated using a numerical electrostatic model in the context of the electrostatic ion beam trap (EIBT). With the simulation results, the principle of mass analysis using the induced signal is demonstrated and studied systematically. The results show that the intensity of the detected signal is significantly influenced by the size and configuration of the detector, and also impacted by ion velocity, the number of ions in the ion group, and the ion beam length. The simulation results could not only be used to optimize the size and configuration of the detector and thus to improve the detected signal, but also to support the signal analysis (such as FFT) at an EIBT for mass spectrometry.     

Limits of agreement method for comparing TSD and FWD measurements

This article uses the limits of agreement (LOA) method to compare the falling weight deflectometer (FWD) and the traffic speed deflectometer (TSD), two pavement structural evaluation devices. The TSD measures deflection slope, whereas the FWD measures deflection. For this reason, measurements were converted to the surface curvature index (SCI) and the base damage index (BDI), which can be obtained from each device. The SCI and BDI agreement between the two devices was then evaluated. Although the relationship between the calculated SCI and BDI using both equipments is reasonably close to the line of equality, there is a significant variation and a bias in this relationship. For example, for an average SCI or BDI value of 300 μm, the bias was 30 μm (FWD values lower than TSD values), and the LOA was 380 μm.     

Low energy O2 and N2O ion beam modification of polyimide for improving adhesive strength of Cu/PI in roll-to-roll process

To enhance the weak mechanical durability of directly deposited copper layers on polyimide (PI) film due to their poor adhesive strength, a continuous roll-to-roll process involving surface modification using a reactive ion beam irradiation and in-situ deposition process is studied. The polyimide film is modified by an ion source with a linear stationary plasma thruster (LSPT) in the vacuum roll-to-roll process. An O₂ ion beam, with beam energy of 214 eV and beam current density of 0.78 mA/cm², and N₂O ion beam, with 220 eV and 0.69 mA/cm², irradiate PI film in winding speed of 0.5 m/min. The surface energy increases from 38 mN/m for the pristine PI film to 80 mN/m after beam irradiation at an ion fluence of 3.5 × 10¹⁶ ions/s. After beam irradiation, a 10 nm thick tie layer and 200 nm thick copper layer are successively deposited by in-situ DC magnetron web coating. The peel strength of the copper layer on the PI film is enhanced from 0.4 kgf/cm without ion beam treatment to 0.71 kgf/cm after O₂ beam treatment and to 0.75 kgf/cm after N₂O beam treatment. This enhancement is closely related to the increase in the polar force originating from the formation of hydrophilic CO (carbonyl) groups on the modified PI surface.     

A controllable and byproduct-free synthesis method of carbon-coated silicon nanoparticles by induction thermal plasma for lithium ion battery

Carbon coated silicon nanoparticle is regarded as a promising anode material for the next generation of lithium ion batteries, while the development of a cost-effective and environmental-friendly preparation method is still difficult and hinders the practical implementation. In this research, a controllable and byproduct-free synthesis method is proposed for the preparation of silicon nanoparticles with amorphous hydrogenated carbon coating. The current apparatus is operated based on the application of induction thermal plasma. Plasma properties are tunable by adjusting the ratio of tangential and radial gas flow rates (T/R), which compose the plasma sheath gas. Obtained results reveal the plasma shape is shrunk with higher T/R values, which will lead to a steeper temperature gradient and lower temperature distributions in reaction chamber. Consequently, the compositions and properties of synthesized particles can be modified with T/R values. The formation of SiC, which was an intractable issue before, can be vanished at higher tangential gas flow rates in current research and the capacity of silicon anode for batteries will be improved in predict. This research is significant for a deep understanding of plasma synthesis processing and design of batteries with excellent performance.     

Development of UV/VIS spectrometric methodology for corrosion inhibitor residuals monitoring in oilfield brine

This work focuses on the development of UV/VIS spectrometric methodology for corrosion inhibitor residuals monitoring in oilfield brine. There is no standard method for the determination of corrosion inhibitor concentration in oilfield brine. Developed methodology can be described as a rugged and simple alternative to the sophisticate separation techniques and can be easily applied in the field. The applicability of the method is demonstrated by the analyses of three commercial products. The extensive performance characteristics test, in combination with study and quantification of measurement uncertainty, shows that developed method meets all required criteria and can be directly applied for routine monitoring purposes within quality management system conditions. Therefore, this new method was accredited by the respectable accreditation agency. Valid and reliable determination of corrosion inhibitor residuals in oilfield brine is important in order to ensure effective corrosion protection of metal construction.