Micro-crystalline inclusions analysis by PIXE and RBS

A characteristic feature of the nuclear microprobe using a 3 MeV proton beam is the long range of particles (around 70 μm in light matrices). The PIXE method, with EDS analysis and using the multilayer approach for treating the X-ray spectrum allows the chemistry of an intra-crystalline inclusion to be measured, provided the inclusion roof and thickness at the impact point of the beam (Z and e, respectively) are known (the depth of the inclusion floor is Z + e). The parameter Z of an inclusion in a mineral can be measured with a precision of around 1 μm using a motorized microscope. However, this value may significantly depart from Z if the analyzed inclusion has a complex shape. The parameter e can hardly be measured optically. By using combined RBS and PIXE measurements, it is possible to obtain the geometrical information needed for quantitative elemental analysis. This paper will present measurements on synthetic samples to investigate the advantages of the technique, and also on natural solid and fluid inclusions in quartz. The influence of the geometrical parameters will be discussed with regard to the concentration determination by PIXE. In particular, accuracy of monazite micro-inclusion dating by coupled PIXE-RBS will be presented.     

PIXE and XRF analysis of particulate matter samples: an inter-laboratory comparison

PIXE and XRF are very effective techniques in atmospheric aerosol investigation, therefore they are extensively used by the authors. In this work an inter-laboratory comparison of the results obtained analysing several samples (collected on different substrata) with both techniques is presented: the samples were analysed by PIXE (in Florence, at the 3 MV Tandetron accelerator of LABEC laboratory) and by XRF (in Genoa and Milan, where two Oxford XRF instruments are operational). The results of the three sets of measurements are in good agreement for all the analysed samples.The aim of this work was also to compare PIXE and XRF performance in atmospheric aerosol analysis with the routine set-up currently in use at the three laboratories, to determine the best technique to be applied depending on the substratum used for aerosol sampling and the main elements of interest for each specific research project. Results of the comparison between the minimum detection limits of both techniques will be shown for all the measured elements, for different substrata (Teflon, polycarbonate and cellulose mixed esters).     

External-beam PIXE characterization of volcanic material used in ancient Roman mortars

Volcanic deposits from two volcanic districts, Monti Sabatini (MSVD) and Colli Albani (CAVD), NW and SE of Rome, were analyzed using the particle-induced X-ray emission (PIXE) technique, in order to obtain chemical fingerprints that can be used for provenance studies of filler materials in ancient Roman mortars. The rock samples were mounted on an X-Y stage enabling scanning over the sample surface and irradiated in air with a collimated 3 MeV proton beam. The samples were either analyzed by scanning the beam over a polished surface or they were crushed, ground and homogenized prior to the irradiation. However, scanning over polished sample surfaces avoiding heterogeneities gave quite similar results as scanning over pellet surfaces, especially for the minor and trace elements. This study shows that the deposits of MSVD and CAVD can be distinguished from each other. Several elements or elemental ratios can be used to characterize the districts. Even the individual volcanic deposits of CAVD can be identified.     

PIXE analysis of chromium phytoaccumulation by the aquatic macrophytes Eicchornia crassipes

The uptake of hexavalent chromium in free living floating aquatic macrophytes Eicchornia crassipes cultivated in non-toxic chromium-doped hydroponic solutions is presented. A Cr-uptake bioaccumulation experiment was carried out using healthy macrophytes grown in a temperature controlled greenhouse. Six samples of nutrient media and plants were collected during the 23 day experiment. Roots and leaves were acid digested with the addition of an internal Gallium standard, for thin film sample preparation and quantitative Cr analysis by PIXE method. The Cr⁶⁺ mass uptake by the macrophytes reached up to 70% of the initial concentration, comparable to former results and literature data. The Cr-uptake data were described using a non-structural first order kinetic model. Due to low cost and high removal efficiency, living aquatic macrophytes E. crassipes are a viable biosorbent in an artificial wetland of a water effluent treatment plant.     

Characterisation of an enamelled metallic object found in Guerrero Negro (Baja California) by PIXE and RBS techniques

The coast of Guerrero Negro (Baja California) has been known for a long time by archaeologists for its shipwrecks. Archaeologists are recovering objects that come from sunken Spanish galleons in the colonial period, and reach the American coast in the frontier of the USA with Mexico.An enamelled metallic object was found next to the beach in Guerrero Negro. We have analysed the piece with proton induced X-ray emission (PIXE) and Rutherford backscattering (RBS) in an attempt to establish whether the object could come from one of the colonial shipwrecks and to valuate its cleaning process.Scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS) have been also performed in three samples taken from the object in order to observe the heterogeneity of the material.The materials found revealed the presence of typical lead-glass enamels from with pigments such as cuprite (red), or lead-tin yellow used in colonial times. The metallic part consisted of brass. As for the cleaning process, the average efficiency considered as the weight% of chlorine removed, was of 83.4% for brass and 100% for enamels.     

PIGE analysis and profiling of aluminium

In this work we present an alternative method for PIGE analysis of aluminium in thick samples. This method is based on the ERYA - emitted radiation yield analysis - code, which integrates the nuclear reaction excitation function along the depth of the sample. For this purpose, the excitations functions of the ²⁷Al(p,p′γ_1,2)²⁷Al reaction (with gamma-ray energies of 844 and 1014 keV) were employed. Calculated gamma-ray yields were compared, at several proton energy values, with experimental yields for thick samples made of inorganic compounds containing aluminium. The agreement is better than 5%.The 1684 keV resonance of the same reaction, with a natural width of 100 eV, was used to profile samples of Ti implanted with several doses of Al. We show that this resonance, stronger than the 992 keV resonance of the ²⁷Al(p,γ)²⁸Si usually employed for aluminium profiling, leads to similar depth resolution in shorter collection time.     

The sensitivity of the PIGE analytical technique

The aim of this work is to provide a basis for the estimation of fluorine and lithium contributions to the background of gamma-ray spectra and of their influence on PIGE (Proton-Induced Gamma-Ray Emission) detection limits of lithium, boron, fluorine and sodium. Results for yields and background contributions of lithium and fluorine were obtained from measurements using samples of known composition. Detection limits were determined by extrapolation of those measurements and by calculations based on the inferred background values. Yields were converted in concentrations using the ERYA (Emitted Radiation Yield Analysis) code. This code divides the sample in sublayers parallel to its surface for the integration of the partial gamma-ray yields along the depth of the target.     

PIXE as a complement to trace metal analysis of sediments by ICP-OES

The adverse effects of metal contamination in sediments require methods that can quickly and accurately assess the extent of environmental pollution. Particle induced X-ray emission spectrometry (PIXE) is demonstrated to be a viable alternative to an established method, which consists of acid digestion and Inductively coupled plasma-optical emission spectrometry (ICP-OES) to measure trace metals in sediment. The analysis of trace metal composition by both techniques on a NIST Standard Reference Material mud gives results that are consistent with the certified values for fourteen measured metals, seven of which are common to both methods. A comparison study conducted on a sediment core from a freshwater lake with a known chromium contamination in Muskegon County, MI also shows a good correlation between the methods for transition metals of environmental interest over a wide range of metal concentrations. Total sample preparation and analysis time for the PIXE measurements is roughly one third that of acid digestion and ICP-OES. Also, the acid digestion step does not elute all the metal, while the nondestructive PIXE approach is a total metals analysis method. However the PIXE method generally has higher limits of detection for many environmental metal contaminants. By combining the two techniques, the acid digestion elution factor can be quantified by running PIXE on an original sample and on the residue resulting from acid digestion.     

Silver surface enrichment controlled by simultaneous RBS for reliable PIXE analysis of ancient coins

Evidence of silver surface enrichment of ancient silver-copper coins has been pointed out in the past years. Surface enrichment can be fortuitous or intentional. In this paper, we have investigated the cleaning procedures usually performed after excavation or in museums. We have shown that chemicals or commercial products routinely used dissolve preferentially the copper phase and consequently contribute to the silver surface enrichment. As a result, surface analyses such as PIXE or XRF can be strongly affected by this effect. By using simultaneously RBS and PIXE, it is possible to check through the silver surface enrichment and then select the reliable measurements, characteristic of the bulk composition. Results on coins recently discovered and mechanically or chemically cleaned are presented.     

PIXE analysis of obsidian tools from radiocarbon dated archaeological contexts

Obsidian tools from archaeological sites in Turkey and Southern Italy, ¹⁴C-AMS dated to the Neolithic were submitted to IBA analyses at CEDAD, University of Salento, Italy. PIXE and PIGE quantitative analysis of major and trace elements allowed the separation of the samples in different compositional groups corresponding to different sources of obsidian, identified on the basis of published data.     

PIXE and RBS analysis of Tl-1223 superconducting phase substituted by scandium

Ion beam analysis techniques (IBA) were performed to determine the elemental stoichiometry of superconducting samples of type TlBa₂Ca_2−xSc_xCu₃O_9−δ, with 0 ? x ? 0.6, prepared via solid-state reaction technique. By combining particle induced X-ray emission (PIXE) with Rutherford backscattering spectrometry (RBS), the stoichiometry of the samples is determined. However, the oxygen content is obtained by using non-Rutherford backscattering cross-section at 3 MeV proton beam. Furthermore, the prepared samples were also characterized using X-ray powder diffraction (XRD) and electrical resistivity measurements. The X-ray data indicate that the partial substitution of Ca²⁺ by Sc³⁺ ions does not affect the tetragonal structure of Tl-1223 superconducting phase. The superconducting transition temperatures T_c, determined from electrical resistivity measurements, was found to be highly correlated to the Sc-content.     

The new Cyclone 18/9 beam transport line at the CNA (Sevilla) for high energy PIXE applications

The Cyclone 18/9 cyclotron system at the Centro Nacional de Aceleradores (Sevilla, Spain) is commonly used to create short life radioisotopes for PET applications. Besides, an external beam transport line has been recently installed in one of the target ports with two major purposes: to study the effects of 18 MeV protons irradiation on the behaviour of electronic devices for space applications and to complement the analysis of materials using our 3 MV tandem accelerator with the PIXE measurements at high energy.In this work, the main elements of our beamline will be briefly described and the first PIXE application will be presented. The usual PIXE, in the analysis of archaeological metallic objects, using around 3 MeV protons requires having a shiny area. Our purpose is to obtain a deeper determination of the bulk composition bombarding with 18 MeV protons through the corroded samples surfaces, without polishing the ancient object. To check this methodology high energy PIXE has been performed on two fibulae of the Later Bronze Age and First Iron Age, coming from the area around Sevilla.     

Study of the provenance of Belgian Merovingian garnets by PIXE at IPNAS cyclotron

Recent archaeological excavation in Belgium reveals one of the biggest Merovingian necropolis ever found in this country. This necropolis contains 436 tombs with a period of occupation of almost two centuries. Some of these tombs were very rich, especially two of them, and delivered an important funerary furniture. About 60 jewels inlaid with red garnets have been found, most of them of “cloisonné” style (namely about 450 garnets). The new extracted beam set-up of the IPNAS cyclotron (University of Liège, Belgium) has been improved in order to analyse by PIXE these garnets and try to determine their provenance. These analyses reveal that the garnets found in the necropolis of Grez-Doiceau are very homogeneous in composition (almandine garnets) and are coming almost from a unique source.These results have been compared to previous studies led in France during these past five years. This permits to identify the source of almandine garnet situated in India and to highlight differences in garnet supply between France and Belgium in Merovingian times.     

PIXE characterization of CsI(Tl) scintillators used for particle detection in nuclear reactions

Particle-Induced X-ray Emission has been used to measure Thallium concentration in several CsI(Tl) scintillators from different manufacturers, in order to check their nominal declared values and correlate their behaviour with actual Tl concentration. Indeed, both Tl doping level and its uniformity affect light emission of these detectors, which are largely employed in nuclear physics experiments.In some of the examined crystals Tl concentration values from PIXE measurements came out to be quite different from those declared. This allowed us to explain apparent anomalies in the trend of their α/γ-induced light yield ratio versus Tl content. In some cases, the presence of unexpected contaminants was also pointed out.     

Use of silicon drift detectors for the detection of medium-light elements in PIXE

In order to fully exploit in PIXE the superior performance of silicon drift detectors especially for the detection of low- and medium-energy X-rays, avoiding in particular the negative effects of backscattered particles, we developed a custom spectrometer based on a 10 mm² chip with a thermoelectric Peltier cooler and home-designed front-end electronics, coupled to a weakly focusing polycapillary lens.This paper briefly describes the detector + lens assembly and reports the results of first tests carried out at an external beam line of the LABEC laboratory in Florence. Excellent energy resolution is achieved under real operating conditions in a PIXE run (measured FWHM at 1 keV is 81 eV with a count-rate of 480 cps) and also the lineshapes are very good (FW1/10M over FWHM ratio is 2.1). As a whole, our preliminary tests gave encouraging results and also helped to point out some aspects which it is worthwhile to investigate further (e.g. how X-ray peak intensity ratios may be affected by inaccurate lens alignment), in order to profit fully from such a good performance of the spectrometer.     

Differential and scanning-mode external PIXE for the analysis of the painting “Ritratto Trivulzio” by Antonello da Messina

Extensive PIXE investigations have been performed at the LABEC accelerator laboratory in Florence on the painting “Ritratto Trivulzio” by Antonello da Messina, one of the great Italian masters of XV Century and a pioneer in modern oil painting.It is well known that a complete and unambiguous characterisation of materials in paintings is often difficult, owing to their complex structure. For the “Ritratto Trivulzio”, the combination of advanced variants of PIXE, such as differential and scanning-mode analysis, provided a relevant contribution to the characterisation of paint layers, in terms of composition and structure, in a totally non-invasive and non-destructive way.Single-spot mode PIXE with external proton beams of about half millimetre diameter was first used for a general characterisation of different areas of the painting. Differential PIXE performed in many spots led to reconstruct the sequence of paints employed by the artist and to estimate in some cases the local paint layer thickness.A second run carried out with the external scanning microbeam facility, using a 3 MeV proton beam of about 80 μm size, was then crucial to clarify some issues raised by the first analysis. In particular, elemental maps from selected areas helped to understand the way some colour shades had been obtained on the red mantle of the portrayed gentleman, using different pigments irregularly distributed on the surface.     

Effects of the behaviour of the proton-induced isotopes production on the analysis of ancient alloys

The present work concerns non-destructive ion beam analysis carried out by means of proton-beam-induced nuclear reactions in the 10-30 MeV energy range. We focused our attention on the yield distribution of the isotopes produced in the internal region of a metal alloy. This distribution, which defines the analytical region, displays, at incident energy of about 20 MeV in a bronze based alloy, a bell-shaped curve centred at about 600 μm with an average width of about 400 μm. By changing the incident proton energy it is possible to displace the above region in the interior of the metal body. It should be pointed out that if we neglect to take into account the correct behaviour of the isotope yield distribution in samples with surface inhomogeneities we can obtain erroneous analytical results. We describe some experiments based on proton activation analysis (PAA) carried out at the INFN-Laboratori Nazionali del Sud (LNS) in Catania where we verified the bell-shape of the radioactive isotope distribution. The resulting formulas are given for quantitative analysis.It is straightforward that, by choosing the appropriate incident proton energy, it is possible to confine the whole analytical region to the interior of the body, thus eliminating any influence of surface effects. We have called this particular approach deep proton activation analysis (DPAA). Examples of its use on archaeological artefacts are given.     

3D Micro-PIXE at atmospheric pressure: A new tool for the investigation of art and archaeological objects

The paper describes a novel experiment characterized by the development of a confocal geometry in an external Micro-PIXE set-up. The position of X-ray optics in front of the X-ray detector and its proper alignment with respect to the proton micro-beam focus provided the possibility of carrying out 3D Micro-PIXE analysis. As a first application, depth intensity profiles of the major elements that compose the patina layer of a quaternary bronze alloy were measured. A simulation approach of the 3D Micro-PIXE data deduced elemental concentration profiles in rather good agreement with corresponding results obtained by electron probe micro-analysis from a cross-sectioned patina sample. With its non-destructive and depth-resolving properties, as well as its feasibility in atmospheric pressure, 3D Micro-PIXE seems especially suited for investigations in the field of cultural heritage.     

Compositional studies on Transylvanian gold nuggets: Advantages and limitations of PIXE-PIGE analysis

Minute fragments from nine gold nuggets from Transylvania - two belonging to placer deposits and seven to primary deposits - were analyzed by PIXE and PIGE at the AGLAE tandem accelerator of the Centre de Recherche et de Restauration des Musées de France (C2RMF) with a 3 MeV proton beam extracted into air. This study was triggered by some archaeological provenance issues for which the elemental characterization of the Transylvanian gold source, exploited from the Antiquity, was required. All analyzed Transylvanian gold nuggets are characterized by a consistently high amount of Ag (18% on average). Au and Ag add up to roughly 99%, the other elements - Cu, Fe, Te, Pb - being detected only at a trace level. The obtained results are in good agreement with the previous analyses of Transylvanian gold.