Al-TiC对AZ91合金铸态组织的影响

利用EPMA、SEM和XRD等测试手段研究了铸造反应法制备的Al-10%TiC(质量分数,下同)中间合金对AZ91合金晶粒的细化作用。结果表明:晶粒尺寸随中间合金加入量的增加而减小,当加入量为0.5%时,-αMg晶粒的尺寸由基体合金的107μm降至48μm,降低幅度约为55%,而且β相由连续网状向断网状或粒状转变,弥散程度增加。α-Mg晶粒的细化机制可能为:原位TiCp可作为初生-αMg的异质晶核。此外,悬浮在熔体中的TiCp在结晶过程中被推移到固/液界面前沿的液相中,从而降低了初生-αMg相的生长速度,最终导致α晶粒的进一步细化。     

纳米SiC对AZ91D镁合金组织和性能的影响

为了研究不同SiC p含量对AZ91 D镁合金的强化机理,采用扫描电子显微镜测定了各相的微观结构组织形貌和分布特征.同时,结合X射线衍射分析结果,探究其强化机制.结果表明,纳米SiC p加入使基体组织变为柱状晶和树枝晶.纳米SiC p的加入可以显著改善基体结构.在本次实验中,纳米SiCp的含量与晶粒尺寸成反比.当纳米S...     

不锈钢丝增强AZ91镁合金复合材料的显微组织及其力学性能

采用渗流铸造法制备了体积分数约为40%、60%、80%的不锈钢丝增强AZ91镁合金复合材料.利用万能试验机对其进行压缩实验;并利用扫描电镜观察复合材料的显微组织以及压缩后的断口形貌.结果表明:不锈钢丝在AZ91镁合金基体中的分布随着其体积分数的增加逐步均匀;不锈钢丝与AZ91镁合金界面润湿性较好.压缩试验表明:复合材料的抗压强度较AZ91镁合金抗压强度明显提高,40%、60%、80%体积分数的复合材料断裂强度分别为371、387、553 MPa;随着不锈钢丝体积分数的增加,材料的破坏方式由剪切破坏转变为劈裂.     

SRB对微弧氧化AZ91镁合金的腐蚀影响

用实验方法研究了微弧氧化AZ91镁合金在SRB培养基中的腐蚀行为,对实验结果进行了分析。结果表明:4种挂片的腐蚀程度按从大到小的顺序排列为无菌基体合金有菌基体合金有菌MAO合金无菌MAO合金;MAO膜的存在显著提高了AZ91合金在无菌培养基中的耐腐蚀性;SRB的存在加速了微弧氧化AZ91镁合金的膜下穿孔,腐蚀孔孔口的形状为近圆形。     

离心铸造对AZ91镁合金组织及力学性能的影响

为了研究卧式离心铸造工艺对AZ91镁合金力学性能及显微组织的影响,采用卧式离心铸造方法制备外径为400 mm、厚度为20 mm且长度为1 000 mm的AZ91镁合金管材,并对离心铸造态与自然凝固态AZ91镁合金管材的微观组织及力学性能分别进行了观察与测试.结果表明,离心铸造态AZ91镁合金管材的抗拉强度和伸长率分别为158 MPa和3.4%,与自然凝固态管材相比分别提高了20%和89%.离心铸造态镁合金管材的微观组织得到明显细化.与自然凝固态AZ91镁合金管材相比,离心铸造态AZ91镁合金管材在凝固过程中的共晶转变在很大程度上受到抑制,并形成了以α-Mg为主相的组织.卧式离心铸造方法提高了AZ91镁合金的综合力学性能,并使合金的组织得到细化.     

AZ91D镁合金半固态加工技术研究进展

半固态加工技术包括半固态浆料或坯料的制备和成形工艺,已经广泛应用于镁合金的加工.AZ91D是镁合金半固态研究及工业应用中最成功的一种镁合金,文中介绍了半固态加工技术及其特点,综述了近年来AZ91D镁合金半固态加工技术的研究现状与进展,包括半固态镁合金的微观组织、成形工艺及其成形件的性能,指出了镁合金半固态加工技术存在的...     

热处理对反向挤压AZ80镁合金组织与性能的影响

采用光学和扫描电子显微观察、X射线衍射及拉伸试验研究了反向挤压AZ80镁合金不同热处理状态下的显微组织及性能．结果表明：反向挤压AZ80镁合金热处理后析出的β－Mg17Al12相（β相）在不同热处理状态下形貌不同．经T6热处理后,口相在晶界处呈层片状析出,与挤压态相比,合金的强度稍有降低,但延伸率明显提高;经T5热处理后,卢相在晶界处仍呈层片状,而在晶内呈颗粒状,与挤压态相比,合金的强度明显提高,但延伸率降低．     

Y对AZ31镁合金铸态组织和性能的影响

采用真空熔炼炉制备AZ31Y镁合金.观察其微观组织,对析出相进行分析,并着重讨论了提高其力学性能的途径.结果表明,Y在AZ31镁合金中主要以块状A12Y化合物形式存在;高熔点的A12Y在合金凝固过程中首先析出,成为凝固的异质形核剂,从而细化了合金组织,改善了室温和高温力学性能;由于Y的强化,含Y AZ31镁合金平均晶粒尺寸降低幅度约为35.82%;室温抗拉强度、屈服强度和延伸率分别为212MPa,147 MPa和7.5%,200℃时分别为117 MPa,98 MPa和10.2 %.     

钕对AZ91镁合金组织及机械性能的影响

采用微观分析、机械性能测试及断口分析等方法研究了钕对AZ91-Nd镁合金(w(Nd)=0,0.1%,0.3%,0.5%,1.0%,1.5%)的微观组织和机械性能的影响。结果表明:Nd以固溶和金属间化合物(A l11Nd3)的形式存在时具有细化晶粒、抑制二次β相析出、使不完全离异共晶转化为离异共晶的作用;Nd通过固溶强化、析出强化和细晶强化增加了合金强度和硬度,并改善了塑性;加入Nd后合金的断裂机制从脆性解理断裂转变为准解理断裂。     

Y和Ce对AZ91D镁合金显微组织和力学性能的影响

为了开发低成本、高强度、耐高温的新型镁合金,研究了微量Y、Ce对AZ91D镁合金显微组织和力学性能的影响。研究结果表明:Y和Ce复合加入AZ91D镁合金,能明显细化组织晶粒,从而改善合金在室温和高温下的力学性能。当加入0.6%Ce-0.3%Y(质量分数)时,合金晶粒细化效果较好,其室温和高温力学性能比较理想。     

Influence of electromagnetic stirring on microstructure of AZ91-0.8%Ce magnesium alloy

1 INTRODUCTION In recent years, magnesium alloys have been used in the automobile industry to save fuel and lower emission levels, and about 60 different types of components of magnesium alloys have been applied in automobile parts, in which AZ91magnesium alloy (Mg-Al system) approximately accounts for 90%[1?4]. It is well known that grain size has very important effect on material properties. According to Hall-Petch equation, when grain size decreases, the mechanical properties such as…     

热挤压镁合金AZ91的微观组织及其力学行为

研究了热挤压镁合金AZ91的微观组织以及在不同试验温度和不同的热处理条件下的拉伸力学性能.结果表明：热挤压可以显著减小AZ91合金的晶粒尺寸，其拉伸力学性能与试验温度密切相关；可以通过热处理来改善其拉伸力学性能，其中人工时效及固溶时效工艺均是改善和提高挤压后AZ91镁合金力学性能的有效途径.此外，利用扫描电镜分析了AZ91镁合金拉伸试样的断口形貌，并探讨了其拉伸断裂机制.     

挤压比对AZ91镁合金组织及力学性能的影响

研究了挤压比对热挤压AZ91镁合金显微组织和拉伸性能的影响.结果表明：热挤压可以显著细化AZ91镁合金的晶粒，而且随着挤压比的增加，晶粒变得更加细小；增大挤压比也可以提高AZ91镁合金在不同实验温度下的抗拉强度和屈服强度，且经过3种挤压比挤压的AZ91镁合金在150 ℃时均呈现最高的抗拉强度和屈服强度；此外，经不同挤压比挤压的AZ91镁合金的伸长率均随实验温度的升高而增加.通过拉伸断口形貌的扫描电镜分析，确定了热挤压AZ91镁合金在室温拉伸时均表现为解理断裂为主的脆性断裂，而在较高温度下拉伸时则基本呈现韧性断裂特征.     

Effect of RE on the ignition-proof, microstructure and properties of AZ91D magnesium alloy

The magnesium alloy is prone to burn during die-casting, which limits its applications severely, so the effect of adding rare earth （RE） on the ignition-proof of AZ91D Mg alloy is studied. The results indicate that the addition of mischmetal RE elements has a remarkable influence on the ignition-proof property of the magnesium alloy. It is found that the ignition temperature of the magnesium alloy can be greatly raised by adding a proper amount of RE. When the amount is 0.1wt%, the ignition temperature reaches 877℃ which is 206℃ higher than that of AZ91D without RE and the mechanical properties of the alloy are also improved, However, the amount of RE must be properly controlled because too much RE would induce grain coarsening and reduce the mechanical properties.     

Microstructure and mechanical properties of AZ91 magnesium alloy subject to deep cryogenic treatments

AZ91 magnesium alloy was subjected to a deep cryogenic treatment. X-ray diffraction （XRD）, scanning electronic microscopy （SEM）, and transmission electronic microscopy （TEM） methods were utilized to characterize the composition and microstructure of the treated samples. The results show that after two cryogenic treatments, the quantity of the precipitate hardening β phase increases, and the sizes of the precipitates are refined from 8-10μm to 2-4μm. This is expected to be due to the decreased solubility of aluminum in the matrix at low temperature and the significant plastic deformation owing to internal differences in thermal contraction between phases and grains. The polycrystalline matrix is also noticeably refined, with the sizes of the subsequent nanocrystalline grains in the range of 50-100 nm. High density dislocations are observed to pile up at the grain boundaries, inducing the dynamic recrystallization of the microstructure, leading to the generation of a nanocrystalline grain structure. After two deep cryogenic treatments, the tensile strength and elongation are found to be substantially increased, rising from 243 MPa and 4.4% of as-cast state to 299 MPa and 5.1%.     

Characterization of microstructure evolution and mechanical properties of the spray-deposited AZ31 magnesium alloy

The cylindrical billets of a Mg-3Al-1Zn (AZ31) alloy were synthesized by spray deposition processing. The microstruc-ture evolution and mechanical properties of the alloy were investigated. The results reveal that the microstructure of the AZ31 alloy is refined significantly by spray deposition processing. A homogeneous and equiaxial-grain structure with an average grain size of 17 μm is obtained. Further grain refinement with an average grain size of 5 μm is attributed to dynamic recrystallization during e...