A 0.6-V Low Power UWB CMOS LNA

This paper presents the design of a low-power ultra-wideband low noise amplifier in 0.18-mum CMOS technology. The inductive degeneration is applied to the conventional distributed amplifier design to reduce the broadband noise figure under low power operation condition. A common-source amplifier is cascaded to the distributed amplifier to improve the gain at high frequency and extend the bandwidth. Operated at 0.6V, the integrated UWB CMOS LNA consumes 7mW. The measured gain of the LNA is 10dB with the bandwidth from 2.7 to 9.1GHz. The input and output return loss is more than 10dB. The noise figure of the LNA varies from 3.8 to 6.9dB, with the average noise figure of 4.65dB. The low power consumption of this work leads to the excellent figure of gain-bandwidth product (GBP) per milliwatt     

High‐Gain Wideband CMOS Low Noise Amplifier with Two‐Stage Cascode and Simplified Chebyshev Filter

An ultra‐wideband low‐noise amplifier is proposed with operation up to 8.2 GHz. The amplifier is fabricated with a 0.18‐μm CMOS process and adopts a two‐stage cascode architecture and a simplified Chebyshev filter for high gain, wide band, input‐impedance matching, and low noise. The gain of 19.2 dB and minimum noise figure of 3.3 dB are measured over 3.4 to 8.2 GHz while consuming 17.3 mW of power. The Proposed UWB LNA achieves a measured power‐gain bandwidth product of 399.4 GHz.     

A 1.2 V Reactive-Feedback 3.1–10.6 GHz Low-Noise Amplifier in 0.13 μm CMOS

A 15.1 dB gain, 2.1 dB (min.) noise figure low-noise amplifier (LNA) fabricated in 0.13 mum CMOS operates across the entire 3.1-10.6 GHz ultrawideband (UWB). Noise figure variation over the band is limited to 0.43 dB. Reactive (transformer) feedback reduces the noise figure, stabilizes the gain, and sets the terminal impedances over the desired bandwidth. It also provides a means of separating ESD protection circuitry from the RF input path. Bias current-reuse limits power consumption of the 0.87mm² IC to 9 mW from a 1.2 V supply. Comparable measured results are presented from both packaged and wafer probed test samples     

A low power high gain UWB LNA in 0.18-μm CMOS

A low power high gain differential UWB low noise amplifier (LNA) operating at 3-5 GHz is presented.A common gate input stage is used for wideband input matching; capacitor cross coupling (CCC) and current reuse techniques are combined to achieve high gain under low power consumption. The prototypes fabricated in 0.18-μm CMOS achieve a peak power gain of 17.5 dB with a -3 dB bandwidth of 2.8-5 GHz, a measured minimum noise figure (NF) of 3.35 dB and -12.6 dBm input-referred compression point at 5 GHz, while drawing 4.4 mA from a 1.8 V supply. The peak power gain is 14 dB under a 4.5 mW power consumption (3 mA from a 1.5 V supply). The proposed differential LNA occupies an area of 1.01 mm~2 including test pads.     

6?10 GHz ultra-wideband CMOS LNA

A two-stage matched ultra-wideband CMOS low noise amplifier (LNA) is presented. The LNA is designed to achieve a low noise figure with high voltage gain. The LNA fabricated in a 0.13 mum CMOS process shows a 3.9 dB average noise figure with a 27 dB voltage gain in the 6-10 GHz frequency band with a power consumption of 14 mW.     

A Broadband Noise-Canceling CMOS LNA for 3.1–10.6-GHz UWB Receivers

An ultra-wideband 3.1-10.6-GHz low-noise amplifier employing a broadband noise-canceling technique is presented. By using the proposed circuit and design methodology, the noise from the matching device is greatly suppressed over the desired UWB band, while the noise from other devices performing noise cancellation is minimized by the systematic approach. Fabricated in a 0.18-mum CMOS process, the IC prototype achieves a power gain of 9.7 dB over a -3 dB bandwidth of 1.2-11.9-GHz and a noise figure of 4.5-5.1 dB in the entire UWB band. It consumes 20 mW from a 1.8-V supply and occupies an area of only 0.59 mm²     

Design of low power CMOS ultra wide band low noise amplifier using noise canceling technique

This paper presents a design of a low power CMOS ultra-wideband (UWB) low noise amplifier (LNA) using a noise canceling technique with the TSMC 0.18 μm RF CMOS process. The proposed UWB LNA employs a current-reused structure to decrease the total power consumption instead of using a cascade stage. This structure spends the same DC current for operating two transistors simultaneously. The stagger-tuning technique, which was reported to achieve gain flatness in the required frequency, was adopted to have low and high resonance frequency points over the entire bandwidth from 3.1 to 10.6 GHz. The resonance points were set in 3 GHz and 10 GHz to provide enough gain flatness and return loss. In addition, the noise canceling technique was used to cancel the dominant noise source, which is generated by the first transistor. The simulation results show a flat gain (S₂₁>10 dB) with a good input impedance matching less than –10 dB and a minimum noise figure of 2.9 dB over the entire band. The proposed UWB LNA consumed 15.2 mW from a 1.8 V power supply.     

An Ultra-Wide-Band 0.4–10-GHz LNA in 0.18-μm CMOS

A two-stage ultra-wide-band CMOS low-noise amplifier (LNA) is presented. With the common-gate configuration employed as the input stage, the broad-band input matching is obtained and the noise does not rise rapidly at higher frequency. By combining the common-gate and common-source stages, the broad-band characteristic and small area are achieved by using two inductors. This LNA has been fabricated in a 0.18-mum CMOS process. The measured power gain is 11.2-12.4 dB and noise figure is 4.4-6.5 dB with -3-dB bandwidth of 0.4-10 GHz. The measured IIP3 is -6 dBm at 6 GHz. It consumes 12 mW from a 1.8-V supply voltage and occupies only 0.42 mm²     

Design and Analysis of a Performance-Optimized CMOS UWB Distributed LNA

In this paper, the systematic design and analysis of a CMOS performance-optimized distributed low-noise amplifier (DLNA) comprising bandwidth-enhanced cascode cells will be presented. Each cascode cell employs an inductor between the common-source and common-gate devices to enhance the bandwidth, while reducing the high-frequency input-referred noise. The noise analysis and optimization of the DLNA accurately accounts for the impact of thermal noise of line terminations and all device noise sources of each CMOS cascode cell including flicker noise, correlated gate-induced noise and channel thermal noise on the overall noise figure. A three-stage performance-optimized wideband DLNA has been designed and fabricated in a 0.18-mum SiGe process, where only MOS transistors were utilized. Measurements of the test chip show a flat noise figure of 2.9 dB, a forward gain of 8 dB, and input and output return losses below -12 dB and -10 dB, respectively, across the 7.5 GHz UWB band. The circuit exhibits an average IIP3 of -3.55 dBm. The 872 mum times 872 mum DLNA chip consumes 12 mA of current from a 1.8-V DC voltage.     

A low supply voltage SiGe LNA for ultra-wideband frontends

A low-power low-noise amplifier (LNA) for ultra-wideband (UWB) radio systems is presented. The microwave monolithic integrated circuit (MMIC) has been fabricated using a commercial 0.25-/spl mu/m silicon-germanium (SiGe) bipolar CMOS (BiCMOS) technology. The amplifier uses peaking and feedback techniques to optimize its gain, bandwidth and impedance matching. It operates from 3.4 to 6.9GHz, which corresponds with the low end of the available UWB radio spectrum. The LNA has a peak gain of 10dB and a noise figure less than 5dB over the entire bandwidth. The circuit consumes only 3.5mW using a 1-V supply voltage. A figure of merit (FoM) for LNAs considering bandwidth, gain, noise, power consumption, and technology is proposed. The realized LNA circuit is compared with other recently published low-power LNA designs and shows the highest reported FoM.     

Design of a Sub-mW 960-MHz UWB CMOS LNA

This paper presents a sub-mW ultra-wideband (UWB) fully differential CMOS low-noise amplifier (LNA) operating below 960 MHz for sensor network applications. By utilizing both nMOS and pMOS transistors to boost the transconductance, coupling the input signals to the back-gates of the transistors, and combining the common-gate and shunt-feedback topologies, the LNA achieves 13 dB of power gain, a 3.6 dB minimum noise figure, and -10 dBm of IIP3 with only 0.72 mW of power consumption from a 1.2 V supply     

（英）CMOS毫米波低功耗超宽带共栅低噪声放大器

本文陈述了一个基于单端共栅与共源共栅级联结构的超宽带低噪声放大器(LNA)。该LNA用标准90-nm RF CMOS工艺实现并具有如下特征：在28.5到39 GHz频段内测得的平坦增益大于10 dB;-3 dB带宽从27到42 GHz达到了15 GHz,这几乎覆盖了整个Ka带;最小噪声系数(NF)为4.2 dB,平均NF在27-42 GHz频段内为5.1 dB;S₁₁在整个测试频段内小于-11 dB。40 GHz处输入三阶交调点(IIP3)的测试值为 2 dBm。整个电路的直流功耗为5.3 mW。包括焊盘在内的芯片面积为0.58*0.48 mm2_。     

2～20GHz分布式单片放大器设计

介绍了一种采用0.15μm GaAs PHEMT工艺设计加工的2～20 GHz宽带单片放大器,为了提高电路的整体增益和带宽,在设计电路时采用两级级联分布式结构。此种电路结构不仅能够增加整体电路的增益和带宽,还可以提高电路的反向隔离,获得更低的噪声系数。利用Agilent ADS仿真设计软件对整体电路的原理图和版图进行仿真优化设计。后期电路在中国电子科技集团公司第十三研究所砷化镓工艺线上加工完成。电路性能指标:在2～20 GHz工作频率范围内,小信号增益>13.5 dB;输入输出回波损耗<-9 dB;噪声系数<4.0 dB;P-1>13 dBm。放大器的工作电压5 V,功耗400 mW,芯片面积为3.00 mm×1.6 mm。     

低功耗CMOS低噪声放大器的分析与设计

基于TSMC 0.18μm CMOS工艺,设计了一种低功耗约束下的CMOS低噪声放大器。与传统的共源共栅结构相比,该电路在共源晶体管的栅源间并联一个电容,以优化噪声;并引入一个电感,与级间寄生电容谐振,以提高增益;通过减小晶体管的尺寸,实现了低功耗。模拟结果表明,在2.45 GHz工作频率下,增益大于14 dB,噪声系数小于1 dB,直流功耗小于2 mW。     

An ultra-wideband CMOS low noise amplifier for 3-5-GHz UWB system

An ultra-wideband (UWB) CMOS low noise amplifier (LNA) topology that combines a narrowband LNA with a resistive shunt-feedback is proposed. The resistive shunt-feedback provides wideband input matching with small noise figure (NF) degradation by reducing the Q-factor of the narrowband LNA input and flattens the passband gain. The proposed UWB amplifier is implemented in 0.18-/spl mu/m CMOS technology for a 3.1-5-GHz UWB system. Measurements show a -3-dB gain bandwidth of 2-4.6GHz, a minimum NF of 2.3 dB, a power gain of 9.8 dB, better than -9 dB of input matching, and an input IP3 of -7dBm, while consuming only 12.6 mW of power.     

3.1～5.2GHz超宽带可变增益低噪声放大器设计

低噪声放大器是超宽带接收机系统中最重要的模块之一,设计了一种可应用于3.1～5.2GHz频段超宽带可变增益低噪声放大器。电路输入级采用共栅结构实现超宽带输入匹配,并引入电流舵结构实现了放大器的可变增益。仿真基于TSMC 0.18μm RF CMOS工艺。结果表明,在全频段电路的最大功率增益为10.5dB,增益平坦度小于0.5dB,噪声系数小于5dB,输入反射系数低于-15dB,在1.8V电源电压下,功耗为9mW。因此,该电路能够在低功耗超宽带射频接收机系统中应用。     

A 2.1-6 GHz SiGe BiCMOS low-noise amplifier design for a multi-mode wideband receiver

A wideband low-noise amplifier (LNA) with ESD protection for a multi-mode receiver is presented.The LNA is fabricated in a 0.18-μm SiGe BiCMOS process,covering the 2.1 to 6 GHz frequency band.After optimized noise modeling and circuit design,the measured results show that the LNA has a 12 dB gain over the entire bandwidth,the input third intercept point (IIP3) is -8 dBm at 6 GHz,and the noise figure is from 2.3 to 3.8 dB in the operating band.The overall power consumption is 8 mW at 2.5 V voltage supply.     

Low-power CMOS distributed amplifier using new cascade gain cell for high and low gain modes

A CMOS distributed amplifier (DA) with low-power and flat and high power gain (S₂₁) is presented. In order to decrease noise figure (NF) an RL terminating network used for the gate transmission line instead of single resistance. Besides, a flat and high S₂₁ is achieved by using the proposed cascade gain cell consist of a cascode-stage with bandwidth extension capacitor. In the high-gain mode, under operation condition of V _dd  = 1.2 V and the overall current consumption of 7.8 mA, simulation result shown that the DA consumed 9.4 mW and achieved a flat and high S₂₁ of 20.5 ± 0.5 dB with an average NF of 6.5 dB over the 11 GHz band of interest, one of the best reported flat gain performances for a CMOS UWB DA. In the low-gain mode, the DA achieved average S₂₁ of 15.5 ± 0.25 dB and an average NF of 6.6 dB with low power consumption (P_DC) of 3.6 mW, the lowest P_DC ever reported for a CMOS DA or LNA with an average gain better than 10 dB.     

Ultra-wideband CMOS low noise amplifier

A two-stage ultra-wideband CMOS low noise amplifier (LNA) is proposed. The first stage is optimised for wideband input matching and low noise figure, while the second stage is optimised to extend the -3 dB bandwidth of the overall amplifier. The combination of stages can provide lower noise figure and wider bandwidth simultaneously over that of previously reported feedback-based CMOS amplifiers. The implemented LNA shows a peak gain of 13.5 dB, more than 8.5 dB of input return loss, and a noise figure of 2.5-7.4 dB over a -3 dB bandwidth from 2 to 9 GHz with DC power consumption of 25.2 mW.     

A Ultra-Wideband Amplitude Modulation (AM) Detector Using Schottky Barrier Diodes Fabricated in Foundry CMOS Technology

Utility of Schottky diodes fabricated in foundry digital 130-nm CMOS technology is demonstrated by implementing an ultra-wideband (UWB) amplitude modulation detector consisting of a low-noise amplifier (LNA), a Schottky diode rectifier, and a low-pass filter. The input and output matching of the detector is better than -10 dB from 0-10.3 GHz and 0-1.7 GHz, respectively, and almost covers the entire UWB frequency band (3.1-10.6 GHz). The measured peak conversion gain is -2.2dB. The sensitivity over the band for amplitude modulation with the minimum E _b/N_o of 6 dB is between -53 and -56 dBm. The power consumption is only 8.5 mW