基于孪生支持向量机的齿轮箱故障诊断

针对齿轮箱振动信号非平稳特性以及故障样本数据处理困难的特点,提出了基于小波包分解和孪生支持向量机的故障诊断方法。首先采集信号通过Mallat塔式算法对信号进行小波分解再重构从而获得频带能量谱,然后通过归一化的方法再提取各频带的故障诊断特征向量。并将它送入孪生支持向量机进行训练。实验表明,该方法有效提高了分类精度和鲁棒性,而且具有较高的诊断效率。     

基于双树复小波包和改进SVM的轴承故障诊断

为了提高滚动轴承内圈、滚动体、外圈等故障诊断效率,提出了将双树复小波包和支持向量机（Support Vector Machine,SVM）结合的故障诊断方法。采用双树复小波包对轴承振动信号分解和重构,提取重构信号中的故障能量特征并构造特征样本作为支持向量机诊断模型的输入。针对支持向量机的参数选取没有固定方法而导致故障诊断的准确性降低的问题,采用人工鱼群算法对支持向量机的惩罚系数和核参数进行寻优。用寻优得到的参数建立支持向量机诊断模型对特征样本进行故障诊断。仿真结果表明提出的方法不仅可以提高降噪效果从而得到滚动轴承故障振动的特征信号,而且能实现更高精度的故障诊断。     

基于支持向量机的矿井通风机故障诊断系统的研究

针对矿井通风机故障诊断过程中样本数据有限的特点,本文提出了一种基于支持向量机的矿井通风机故障诊断方法。支持向量机是一种机器学习方法,它对有限的样本数据具有良好的学习能力。采用支持向量机对样本数据通过学习形成故障分类器,利用该分类器对故障样本进行测试,得出矿井通风机的故障诊断结果。结果表明：支持向量机对有限样本数据具有良好的推广能力,最终达到了快速并准确地诊断矿井通风机故障的目的。     

基于EasyEnsemble的化工过程故障诊断性能改进

化工过程故障诊断中样本数据分布不均衡现象普遍存在.在使用不均衡样本作为训练集建立各类故障诊断分类器时,易出现分类器的识别率偏置于多数类样本的结果,由此产生虽正常状态易识别,但更受关注的故障状态却难以被诊断的现象.针对该问题,本文提出一种基于Easy Ensemble思想的主元分析–支持向量机(Easy Ensemble based principle component analysis–support vector machine,EEPS)故障诊断算法,通过欠采样方法抽取多数类样本子集组建多个新的均衡数据样本集,使用主元分析(principle component analysis,PCA)进行特征提取并使用支持向量机(support vector machine,SVM)算法进行训练,得到多个基于SVM的故障诊断分类器,然后使用Adaboost算法集成最终的分类,从而提高故障诊断准确性.所提方法被用于TE(Tenessee Eastman)化工过程,实验结果表明,EEPS算法能够有效提高分类器在不均衡数据集上的诊断性能和预报能力.     

基于小波包分析和LS-SVM的柴油机故障诊断方法

针对某柴油机检测样本小,难以准确估计故障的状况,提出了一种基于小波包分析和最小二乘支持向量机的柴油机故障诊断方法;利用小波包分析对柴油机缸盖振动提取频谱能量并对干扰信号进行处理,从而获得故障征兆样本集;由于柴油机故障的征兆样本集有限性,提出了采用最小二乘支持向量机分类方法构建柴油机故障分类器;结果表明,经过小波处理过后的振动信号再经过LS-SVM辨识网络训练,能够准确地诊断和预测故障。     

基于支持向量机的往复压缩机气阀故障诊断

提出了一种基于支持向量机的往复压缩机气阀故障诊断方法。把往复压缩机气阀的振动信号作为识别故障的特征向量,运用支持向量机方法,训练后得到用于往复压缩机气阀故障诊断的支持向量机网络。由对测试样本的分类结果可知,支持向量机网络的分类结果和实际故障情况一致。     

基于蝙蝠算法优化相关向量机的轴承故障诊断方法

由于轴承振动信号具有复杂性和非线性,难以有效提取故障特征,影响故障诊断的准确率.为了提高故障诊断准确率,提出一种蝙蝠算法(BA)优化相关向量机(RVM)的轴承故障诊断方法.首先结合变分模态分解和多尺度熵从轴承振动信号中提取出故障特征,作为相关向量机的输入向量;接着采用蝙蝠算法优化相关向量机的核函数参数;然后训练相关向量...     

滚动轴承故障诊断优化仿真研究

研究提高滚动轴承故障诊断准确率问题,滚动轴承故障振动信号具有非平稳,造成系统不稳定,针对传统方法难以提取故障信息的不足,提出一种小波包和最小二乘支持向量机的滚动轴承故障诊断方法(WP-LSSVM)。首先采用小波包对滚动轴承振动信号进行降噪处理,消除背景和噪声信息,然后小波包对去噪后振动信号分解并计算能量特征值,最后采用最小二乘支持向量机对能量特征值进行学习,建立滚动轴承故障诊断模型。仿真结果表明,滚动轴承故障诊断训练和测试时间减少,且故障诊断准确率得到提高。     

支持向量机在压缩机气阀故障诊断中的应用

由于结构复杂且缺乏故障样本等原因,往复式压缩机的故障样本及诊断结果存在很强的不确定性。针对典型压缩机气阀振动信号的特点及不同故障机理,研究气阀振动信号的特征参数提取方法。提取工作循环有效值RMS1、气阀关闭段有效值RMS2,以及经两层小波包分解得到的各频带能量比系数E1、E2、E3、E4,组成6维特征向量,并将其作为支持向量机的输入。利用支持向量机适合处理高维数据且在有限样本下具有最优泛化能力的特点,对3种不同气阀状态下的振动信号经时域波形分析和小波包分解后提取的特征参数进行支持向量机学习;建立气阀故障诊断的支持向量机分类模型;利用Libsvm软件包对故障样本进行随机分类测试,并与其他智能诊断方法进行对比。对比结果表明,将支持向量机方法应用于往复式压缩机的气阀故障诊断中具有可行性;在小样本条件下,支持向量机较其他智能诊断方法具有更大的优势。     

基于最大间隔最小体积超球支持向量机的多主题分类算法

针对多主题分类,结合最大间隔最小体积超球支持向量机和模糊理论,提出一种多主题最大间隔最小体积超球支持向量机来实现多主题分类.该算法首先基于最大间隔最小体积超球支持向量机,采用1-a-r方法训练子分类器,通过子分类器得到待分类样本的隶属度向量,再依据隶属度向量判定该待分类样本所属类别.实验结果表明,该算法具有较好的准确率、召回率、F1值.     

Only connect: teaching, technology and telesis

Abstract This paper describes an approach to the design of interactive multimedia materials being developed in a European Community project. The developmental process is seen as a dialogue between technologists and teachers. This dialogue is often problematic because of the differences in training, experience and culture between them. Conditions needed for fruitful dialogue are described and the generic model for learning design used in the project is explained.     

European Community policy and the market

Abstract This paper starts with some reflections on the policy considerations and priorities which are shaping European Commission (EC) research programmes. Then it attempts to position the current projects which seek to capitalise on information and communications technologies for learning in relation to these priorities and the apparent realities of the marketplace. It concludes that while there are grounds to be optimistic about the contribution EC programmes can make to the efficiency and standard of education and training, they are still too technology driven.     

一种自适应子融合集成多分类器方法

融合集成方法已经广泛应用在模式识别领域,然而一些基分类器实时性能稳定性较差,导致多分类器融合性能差,针对上述问题本文提出了一种新的基于多分类器的子融合集成分类器系统。该方法考虑在度量层融合层次之上通过对各类基多分类器进行动态选择,票数最多的类别作为融合系统中对特征向量识别的类别,构成一种新的自适应子融合集成分类器方法。实验表明,该方法比传统的分类器以及分类融合方法识别准确率明显更高,具有更好的鲁棒性。     

Avoiding semantic and temporal gaps in developing software intensive systems

Development of software intensive systems (systems) in practice involves a series of self-contained phases for the lifecycle of a system. Semantic and temporal gaps, which occur among phases and among developer disciplines within and across phases, hinder the ongoing development of a system because of the interdependencies among phases and among disciplines. Such gaps are magnified among systems that are developed at different times by different development teams, which may limit reuse of artifacts of systems development and interoperability among the systems. This article discusses such gaps and a systems development process for avoiding them.     

Designing economic np control charts: A programmed simulation approach

This paper presents control charts models and the necessary simulation software for the location of economic values of the control parameters. The simulation program is written in FORTRAN, requires only 10K of main storage, and can run on most mini and micro computers. Two models are presented - one describes the process when it is operating at full capacity and the other when the process is operating under capacity. The models allow the product quality to deteriorate to a further level before an existing out-of-control state is detected, and they can also be used in situations where no prior knowledge exists of the out-of-control causes and the resulting proportion defectives.     

The development of robot art

Going through a few examples of robot artists who are recognized worldwide, we try to analyze the deepest meaning of what is called “robot art” and the related art field definition. We also try to highlight its well-marked borders, such as kinetic sculptures, kinetic art, cyber art, and cyberpunk. A brief excursion into the importance of the context, the message, and its semiotics is also provided, case by case, together with a few hints on the history of this discipline in the light of an artistic perspective. Therefore, the aim of this article is to try to summarize the main characteristics that might classify robot art as a unique and innovative discipline, and to track down some of the principles by which a robotic artifact can or cannot be considered an art piece in terms of social, cultural, and strictly artistic interest. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Explanation and prediction: an architecture for default and abductive reasoning

Although there are many arguments that logic is an appropriate tool for artificial intelligence, there has been a perceived problem with the monotonicity of classical logic. This paper elaborates on the idea that reasoning should be viewed as theory formation where logic tells us the consequences of our assumptions. The two activities of predicting what is expected to be true and explaining observations are considered in a simple theory formation framework. Properties of each activity are discussed, along with a number of proposals as to what should be predicted or accepted as reasonable explanations. An architecture is proposed to combine explanation and prediction into one coherent framework. Algorithms used to implement the system as well as examples from a running implementation are given.     

Three Process Perspectives: Organizations, Teams, and People

This paper provides the author's personal views and perspectives on software process improvement. Starting with his first work on technology assessment in IBM over 20 years ago, Watts Humphrey describes the process improvement work he has been directly involved in. This includes the development of the early process assessment methods, the original design of the CMM, and the introduction of the Personal Software Process (PSP)^SM and Team Software Process (TSP){^SM}. In addition to describing the original motivation for this work, the author also reviews many of the problems he and his associates encountered and why they solved them the way they did. He also comments on the outstanding issues and likely directions for future work. Finally, this work has built on the experiences and contributions of many people. Mr. Humphrey only describes work that he was personally involved in and he names many of the key contributors. However, so many people have been involved in this work that a full list of the important participants would be impractical.     

基于复小波噪声方差显著修正的SAR图像去噪

提出了一种基于复小波域统计建模与噪声方差估计显著性修正相结合的合成孔径雷达(Synthetic Aperture Radar,SAR)图像斑点噪声滤波方法。该方法首先通过对数变换将乘性噪声模型转化为加性噪声模型,然后对变换后的图像进行双树复小波变换(Dualtree Complex Wavelet Transform,DCWT),并对复数小波系数的统计分布进行建模。在此先验分布的基础上,通过运用贝叶斯估计方法从含噪系数中恢复原始系数,达到滤除噪声的目的。实验结果表明该方法在去除噪声的同时保留了图像的细节信息,取得了很好的降噪效果。     

How do children do mathematics with LOGO?

Abstract  This paper considers some results of a study designed to investigate the kinds of mathematical activity undertaken by children (aged between 8 and 11) as they learned to program in LOGO. A model of learning modes is proposed, which attempts to describe the ways in which children used and acquired understanding of the programming/mathematical concepts involved. The remainder of the paper is concerned with discussing the validity and limitations of the model, and its implications for further research and curriculum development.