Influence of Fiber Surface Modification on the Mechanical Performance of Isora-Polyester Composites

This paper reports the effect of chemical treatment on the mechanical properties of a natural fiber, isora, as reinforcement in unsaturated polyester resin. Isora fiber is separated from the bark of the Helicteres isora plant by a retting process. The short isora fiber surface was modified chemically by acetylation, benzoylation, silane and triton treatments to bring about improved interfacial interaction between the fiber and the polyester matrix. The modified surfaces were characterized by IR spectroscopy and SEM. The SEM studies were carried out to investigate the fiber surface morphology, fiber pull-out and fiber-polyester interface bonding. They showed the changes occuring on the fiber surface during chemical treatment. Properties like tensile strength, flexural strength and impact strength have been studied. The chemical modification of fiber improved fiber/matrix interaction as evidenced by the enhanced tensile and flexural properties. The lower impact properties of the composites, except triton-treated fiber composite, further point to the improved fiber/matrix adhesion, compared to the untreated fiber composites.     

环氧树脂/短切碳纤维复合材料性能研究

制备出了短切碳纤维增强TDE-85环氧树脂复合材料,研究了碳纤维的含量对复合材料力学性能和耐热性能的影响。结果表明,碳纤维的加入有利于复合材料力学性能和耐热性能的提高,并在碳纤维含量为0.25%时,复合材料的拉伸强度、冲击韧性、弯曲强度和弯曲模量达到最大,分别提高了29.33%、25.31%、30.28%和68.93%。此外,对复合材料的弯曲断裂面进行了微观形貌分析,结果表明一定量的碳纤维可以较好地分散在树脂基体中,同时,碳纤维原丝和树脂基体的界面结合比较弱,主要依赖于两相之间的物理嵌合。     

碳纤维湿法缠绕用环氧树脂基体研究

以TDE-85树脂和AFG-90树脂为主体树脂,混合芳香胺为固化剂,研究了一种适合于碳纤维复合材料湿法缠绕成型的树脂配方。结果表明,该树脂的黏度低(＜550 mPa·s)、适用期长,其浇铸体具有优异的力学性能,其拉伸强度为107 MPa,拉伸模量为4．09 GPa,弯曲强度为161 MPa,弯曲模量为3．88 GPa,断裂伸长率超过6%。用其制备的T-700碳纤维缠绕复合材料界面粘接好,NOL环层间剪切强度达到66．8 MPa,拉伸强度达到2．44 GPa。     

Effect of surface cold ablation on shear strength of CFRP adhesively bonded joint after UV laser treatment

Ultraviolet(UV) laser treatment on the surface of the carbon fiber reinforced polymer (CFRP) laminate becomes an effective method to benefit the bonding strength of adhesively bonded joint in aerospace industries. In the present research, homomorphic CFRP laminates with different resin distribution on the surface are bonded into single-lap joints. Their shear strengths are tested to evaluate the effect of surface resin distribution on bonding mechanical performance. The different resin distributions on the surface of CFRP laminate are obtained by UV pulse laser with different laser scanning speeds. The scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) are conducted to analyze the laser treated surfaces and fracture surfaces of tested joints. The experimental results indicate that the residual resin of CFRP surface increases with the increase of scanning speed. Compared with both the reference surface without laser pre-treatment and that with no-residual resin for bonding, the surface with partial residual resin results in an enhancement of the shear strength of bonded joint. Moreover, the shear strength of the reference sample is higher than that bonded by the surface with no-residual resin. The research lays foundation for understanding the relationship between surface resin distribution and bonding strength.     

Study on the interfacial properties of three‐dimensionally arranged glass fiber/epoxy resin model composites

The effect of interfiber distance on the interfacial properties in three‐dimensional multi‐E‐glass fiber/epoxy resin composites has been investigated using fragmentation test. In additions, the effect of the fiber surface treatment on the interfacial properties has been studied. The interfacial shear strength decreased with the decreasing the interfiber distance at the range of under 50 μm and the extent of the decreasing was more serious as the increasing of the number of adjacent fiber. This is probably due to the fact that the interface between the fiber and the resin was damaged by the adjacent fiber breaks and the damage increased with closing the interfiber spacing and the number of adjacent fiber. It was found that the interfacial shear strengths saturated when the interfiber distance was over 50 μm, the ones were saturated regardless of fiber surface treatment and the ones were in close agreement with those of the single fiber fragmentation test. Finally, the interfacial shear strength evaluated using three‐dimensional fragmentation tests are shown as real values in‐site regardless of fiber surface treatment, interfiber distance and existing of matrix cracks. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

碳纤维布/玻纤布增强聚氨酯复合材料的研究

以聚氨酯为基体树脂,分别以碳纤维布、玻璃纤维布和这两种纤维布交替铺叠作为增强材料,采用真空辅助灌注成型工艺制备了4种复合材料.考察了纤维布的铺层结构对复合材料的弯曲、拉伸和冲击性能的影响.结果显示,复合材料的拉伸模量和弯曲模量随碳纤维含量增加而增加,冲击强度则降低.分别采用TGA、DMA和SEM对复合材料的热性能、界面...     

Influence of oxygen plasma treatment parameters on the properties of carbon fiber

This study is focused on the impact of oxygen plasma treatment on properties of carbon fibers and interfacial adhesion behavior between the carbon fibers and epoxy resin. The influences of the main parameters of plasma treatment process, including duration, power, and flow rate of oxygen gas were studied in detail using interlaminar shear strength (ILSS) of carbon fiber composites. The ILSS of composites made of carbon fibers treated by oxygen plasma for 1 min, at power of 125 W, and oxygen flow rate of 100 sccm presented a maximum increase of 28% compared to composites made of untreated carbon fibers. Furthermore, carbon fibers were characterized by scanning electron microscopy (SEM), tensile strength test, attenuated total reflectance Fourier transform infrared (ATR-FTIR), and Raman spectroscopy analyses. It was found that the concentration of reactive functional groups on the fiber surface was increased after the plasma modification, as well the surface roughness, which finally improved the interfacial adhesion between carbon fibers and epoxy resin. However, high power and long exposure times could partly damage the surface of carbon fibers and decrease the tensile strength of filaments and ILSS of treated fiber composites.     

废木屑增强聚丙烯的力学性能及其影响因素

研究了界面处理方法、木屑尺寸、含量、基体树脂等因素对废弃木屑增强聚丙烯复合材料力学性能的影响。在木屑表面涂覆偶联剂KH－570及聚丙烯乳液、在基体中添加改性聚丙烯、或在木屑表面涂履KH－570和过氧化物引发剂得到的复合材料其力学性能有不同程度的提高。经适当界面处理的木屑与聚丙烯复合后,随着木屑含量的提高,材料的拉伸、弯曲性能明显提高,而冲击性能基本保持不变。采用熔体流动速度高的聚丙烯作为基体,制得的复合材料的拉伸、弯曲性能较好,但冲击韧性稍差。     

PAN基高模碳纤维阳极氧化的表面处理

采用阳极氧化法对PAN基高模碳纤维进行连续表面处理,重点研究了氧化电流密度对碳纤维宏观力学性能、表面形貌、表面酸性官能团以及碳纤维增强树脂基复合材料(CFRP)层间剪切强度(ILSS)的影响。结果表明,电流密度对纤维力学性能、表面形貌影响不大;氧化后纤维表面总的酸性官能团显著提高,最大增幅达13倍左右;适当的处理条件可使CFRP的ILSS从28.4 MPa提高到80 MPa以上。     

硅灰石与连续玻璃纤维毡组合增强聚丙烯的力学性能

采用硅灰石与连续玻璃纤维毡组合增强聚丙烯,研究了硅灰石的含量,玻璃纤维毡的面密度、基体树脂的性质及界面改性等对材料力学性能的影响。结果表明：采用硅灰石与连续玻璃纤维毡组合增强,可提高复合材料的拉伸、弯曲强度及模量,但过高的硅灰石含量,会导致拉伸及弯曲强度下降,材料的力学性能随着所用玻璃纤维毡面密度的增大而显著提高,采用偶联剂对硅灰石进行处理及在基体聚丙烯中添加功能化聚丙烯,可改善界面结合、提高材料性能,随着功能化聚丙烯含量的增加,材料的拉伸、弯曲强度及模量有所提高,但含量过高时,会引起材料冲击强度的下降;组合增强材料的性能与基体树脂本身的力学性能密切相关,同时还受基体树脂熔体流动性的影响。     

Pultruded fiber reinforced thermoplastic poly(methyl methacrylate) composites. Part II: Mechanical and thermal properties

A novel process has been developed to manufacture poly(methyl methacrylate) (PMMA) pultruded parts. The mechanical and dynamic mechanical properties, environmental effects, postformability of pultruded composites and properties of various fiber (glass, carbon and Kevlar 49 aramid fiber) reinforced PMMA composites have been studied. Results show that the mechanical and thermal properties (i.e. tensile strength, flexural strength and modulus, impact strength and HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest impact strength and HDT, while carbon fiber/PMMA composites show the highest tensile strength, tensile and flexural modulus, and glass fiber/PMMA composites show the highest flexural strength. Experimental tensile strengths of all composites except carbon fiber/PMMA composites follow the rule of mixtures. The deviation of carbon fiber/PMMA composite is due to the fiber breakage during processing. Pultruded glass fiber reinforced PMMA composites exhibit good weather resistance. They can be postformed by thermoforming, and mechanical properties can be improved by postforming. The dynamic shear storage modulus (G′) of pultruded glass fiber reinforced PMMA composites increased with decreasing pulling rate, and G′ was higher than that of pultruded Nylon 6 and polyester composites.     

Formation of a carbon fiber/polyhedral oligomeric silsesquioxane/carbon nanotube hybrid reinforcement and its effect on the interfacial properties of carbon fiber/epoxy composites

A carbon fiber/polyhedral oligomeric silsesquioxane/carbon nanotube (CF–POSS–CNT) hybrid reinforcement was prepared by grafting CNTs onto the carbon fiber surface using octaglycidyldimethylsilyl POSS as the linkage in an attempt to improve the interfacial properties between carbon fibers and an epoxy matrix. X-ray photoelectron spectroscopy, scanning electron microscopy, dynamic contact angle analysis and single fiber tensile testing were performed to characterize the hybrid reinforcements. Interlaminar shear strength (ILSS), impact toughness, dynamic mechanical analysis and force modulation atomic force microscopy were carried out to investigate the interfacial properties of the composites. Experimental results show that POSS and CNTs are grafted uniformly on the fiber surface and significantly increase the fiber surface roughness. The polar functional groups and surface energy of carbon fibers are obviously increased after the modification. Single fiber tensile testing results demonstrate that the functionalization does not lead to any discernable decrease in the fiber tensile strength. Mechanical property test results indicate the ILSS and impact toughness are enhanced. The storage modulus and service temperature increase by 11 GPa and 17 °C, respectively. POSS and CNTs effectively enhance the interfacial adhesion of the composites by improving resin wettability, increasing chemical bonding and mechanical interlocking.     

Improvement of the mechanical properties of an ultrahigh molecular weight polyethylene fiber/epoxy composite by corona‐discharge treatment

The interfacial shear strength of an ultrahigh molecular weight (UHMW) polyethylene (PE) fiber/epoxy‐resin system was greatly improved by the corona‐discharge treatment of the fiber. The UHMW PE‐fiber/epoxy‐resin composite was prepared with corona‐discharge‐treated UHMW PE fiber. The mechanical properties of the composite sheet were determined by tensile testing. The tensile strength of the composite was also very much improved. However, the tensile strength of the composite was about one‐half of the theoretical strength. This result was due to the molecular degradation of the PE‐fiber surface caused by surface modification. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1162–1168, 2001     

High improvement of interfacial and mechanical properties in reinforced PP composite by grafting polyethyleneimine modified carboxylic multi-walled carbon nanotubes on short carbon fiber

The properties of carbon fiber reinforced polymer composites (CFRPs) will benefit greatly from improving interfacial performance. In this study, the interfacial properties of the PEI-CNT-CF/PP composite was improved by coating polyethyleneimine (PEI) modified carboxylic multi-walled carbon nanotubes (CNTs) in aqueous solution (PEI-CNT) onto the surface of the CF (PEI-CNT-CF) to form a network structure. The network formation changed the chemical characteristics and compatibility of CF surface by introducing amine (imine) groups, and could induce transcrystallization (TC) at interface of composite. These positive factors led to a 24.6% increasement in the interfacial shear strength (IFSS) of PEI-CNT-CF/PP, and further resulted in 16.2% and 5.3% improvement in tensile and flexural strength, respectively. SEM images of the fracture surface demonstrated a significant improvement in the interfacial adhesion between PEI-CNT-CF and PP resin. These results indicated that the PEI-CNT was a great choice to strengthen the interface of CF/PP system.     

碳纤维/聚苯并(噁)嗪复合材料的界面与力学性能的关系研究

本文采用含不同上胶剂的碳纤维与苯并(噁)嗪树脂复合,制备碳纤维/聚苯并(噁)嗪单向复合材料,研究了碳纤维表面上胶剂对于复合材料的层间剪切强度(ILSS)、弯曲性能、断口形貌及动态机械性能的影响.结果表明,含有环氧树脂上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(EPCF/PBZ)的ILSS和弯曲性能优于含非环氧类树脂上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(VECF/PBZ)和不含上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(USCF/PBZ).环氧树脂上胶剂改善了纤维与苯并(噁)嗪树脂的粘结性能,使复合材料的内耗峰峰高降低,能量损耗减小.电镜照片同样验证了这一结果.     

Hybrid carbon-glass fiber vinyl ester resin composites

Hybrid carbon-glass fiber composites of novolak epoxy-based vinyl ester resins have been investigated. The chemical resistance, the thermo-oxidative stability and the mechanical properties such as tensile strength and tensile modulus, as well as flexural strength and flexural modulus, interlaminar shear strength (ILSS) and impact strength have also been estimated. The combination of glass and carbon fibers in the hybrid turns out to be an excellent mix. These composites have good tensile and flexural properties as well as the good chemical resistance of the carbon fibers and the high impact strength of the glass fibers and also the thermo-oxidative stability of highly aromatic vinyl ester resins based on novolak epoxy.     

Study on the interfacial properties of two‐dimensionally arranged glass fiber/epoxy resin model composites

The effect of interfiber distance on the interfacial properties in two dimensional multi‐E‐glass fiber/epoxy resin composites has been investigated using fragmentation test. In addition, the effect of the fiber surface treatment on the interfacial properties has been studied. We found that the interfacial shear strength decreased with the decreasing interfiber distance at the range of <50 μm and the extent of the decreasing was more serious as the increasing of the number of adjacent fiber. This is probably that the interface between the fiber and the resin was damaged by the breaking of adjacent fibers and the damage increased with minimizing the interfiber spacing and the number of adjacent fibers. We can guess that interfacial shear strength in real composites is much smaller than that of multifiber fragmentation sample with touched fiber. When the interfiber distance was >50 μm, the interfacial shear strengths were saturated regardless of fiber surface treatment and were in close agreement with those of the single fiber fragmentation test. Finally, the interfacial shear strength evaluated using two dimensional fragmentation tests are shown as real values in‐site regardless of fiber surface treatment, interfiber distance, and existing matrix cracks. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1541–1551, 2006     

T700碳纤维/环氧树脂复合材料热降解实验研究

针对T700碳纤维增强环氧树脂复合材料的热降解行为以及回收所得碳纤维的力学性能进行了研究。研究结果表明,碳纤维的存在增加了环氧树脂降解时所需的活化能,热降解反应的温度、时间和气氛等因素对环氧树脂基体降解效果以及回收碳纤维力学性能均有影响。在空气条件下500℃处理30 min后碳纤维表面没有残留物,但其回收纤维的拉伸强度保留率仅为77.6%。通过首先在氮气气氛高温短时热处理,再在空气气氛下450℃进行30 min热降解的两步法处理后,碳纤维表面残炭得到去除,回收碳纤维的拉伸强度保留率达到了90.4%,由其制备单向复合材料的层间剪切强度保留率可达到75.8%。     

氨气处理碳纤维 第II报 碳纤维表面和复合材料的性能

常压下,使碳纤维通过以氨气为气体介质的600℃热反应炉,反应停留时间为30s。采用三点短梁法和界面评价装置研究处理前后复合材料的层间剪切强度(ILSS)和界面剪切强度(IFSS),经氨气处理后二者分别提高了13.2%和32.1%。接触角测试结果表明:处理后碳纤维与水和环氧树脂的浸润性得到很大改善。采用扫描电子显微镜(SEM)研究处理前后碳纤维表面和复合材料断裂面形貌的变化,发现氨气处理对碳纤维表面形貌没有影响。力学性能测试数据表明,氨气处理不影响碳纤维的强度。     

界面结合对GF/PDCPD复合材料性能的影响

界面结合性能对制备性能优异的复合材料具有重要意义。通过对双环戊二烯（DCPD）与玻璃纤维（GF）的浸润性进行研究，将其与等效环氧树脂比较，开发了一种与玻璃纤维具有较好结合性的DCPD树脂，用其制备出一种综合性能优异的玻璃纤维增强PDCPD基复合材料。通过动态接触角、90?拉伸强度和层间剪切强度实验，测定了不同树脂与玻璃纤维之间的粘附力，提供了玻璃纤维与不同树脂界面性能差异。结果表明，SCB-600 DCPD树脂与玻璃纤维的结合性较优，动态接触角为60.35??0.3?，90?拉伸强度为(42.3?1.6) MPa，层间剪切强度为(61.3?3.2) MPa，与1564环氧树脂相当。进一步优化了DCPD树脂质量分数，当树脂质量分数为30%?2%时，SCB-600 DCPD复合材料具有相对最优的力学性能，材料拉伸强度为(1180.1?4.1) MPa，弯曲强度为(1060.4?4.6) MPa，缺口冲击强度为(145.3?4.8) KJ/m2。其弯曲和拉伸强度与玻璃纤维增强环氧树脂基复合材料的性能基本相当，但缺口冲击强度优于1564环氧树脂。