Stability of ZrO2 Phases in Ultrafine ZrO2-Al2O3 Mixtures

Mixtures of ultrafine monoclinic zirconia and aluminum hydroxide were prepared by adding NH₄OH to hydrolyzed zirconia sols containing varied amounts of aluminum sulfate. The mixtures were heat-treated at 500° to 1300°C. The relative stability of monoclinic and tetragonal ZrO₂ in these ultrafine particles was studied by X-ray diffractometry. Growth of ZrO₂ crystallites at elevated temperatures was strongly inhibited by Al₂O₃ derived from aluminum hydroxide. The monoclinic-to-tetragonal phase transformation temperature was lowered to ∼500°C in the mixture containing 10 vol% Al₂O₃, and the tetragonal phase was retained on cooling to room temperature. This behavior may be explained on the basis of Garvie's hypothesis that the surface free energy of tetragonal ZrO₂ is lower than that of the monoclinic form. With increasing A1₂O₃ content, however, the transformation temperature gradually increased, although the growth of ZrO₂ particles was inhibited; this was found to be affected by water vapor formed from aluminum hydroxide on heating. The presence of atmospheric water vapor elevates the transformation temperature for ultrafine ZrO₂. The reverse tetragonal-to-monoclinic transformation is promoted by water vapor at lower temperatures. Accordingly, it was concluded that the monoclinic phase in fine ZrO₂ particles was stabilized by the presence of water vapor, which probably decreases the surface energy.     

Stability of Ultrafine Tetragonal ZrO2 Coprecipitated with Al2O3 by the Spray-ICP Technique

The transformation of ultrafine powders (particle size, 0.01 to 0.04 μm) of the system ZrO_2–Al₂O₃, prepared by spraying their corresponding nitrate solutions into an inductively coupled plasma (ICP) of ultrahigh temperature, was investigated. The powders were composed of metastable tetragonal ZrO₂ ( mt- ZrO₂) and γ-Al₂O₃. On heating, the mt- ZrO₂ (or tetragonal ZrO₂, t -ZrO₂) was retained up to 1200°C. At 1380°C the transformation to monoclinic ZrO₂ ( m -ZrO₂) occurred and the amount of the m -ZrO₂ decreased with the increase in Al₂O₃ content, thus indicating the stabilization of the t -ZrO₂ by the Al₂O₃, which seems to be explained in terms of the retardation of grain growth.     

Zirconium Aluminum Carbides: New Precursors for Synthesizing ZrO2–Al2O3 Composites

ZrO₂–Al₂O₃ nanocrystalline powders have been synthesized by oxidizing ternary Zr₂Al₃C₄ powders. The simultaneous oxidation of Al and Zr in Zr₂Al₃C₄ results in homogeneous mixture of ZrO₂ and Al₂O₃ at nanoscale. Bulk nano- and submicro-composites were prepared by hot-pressing as-oxidized powders at 1100°–1500°C. The composition and microstructure evolution during sintering was investigated by XRD, Raman spectroscopy, SEM, and TEM. The crystallite size of ZrO₂ in the composites increased from 7.5 nm for as-oxidized powders to about 0.5 μm at 1500°C, while the tetragonal polymorph gradually converted to monolithic one with increasing crystallite size. The Al₂O₃ in the composites transformed from an amorphous phase in as oxidized powders to θ phase at 1100°C and α phase at higher temperatures. The hardness of the composite increased from 2.0 GPa at 1100°C to 13.5 GPa at 1400°C due to the increase of density.     

Coupled Grain Growth Effects in Al2O3/10 vol% ZrO2

Coupled crystallization has been observed in the Al₃O₃/10%-ZrO₂ system by heating an amorphous precursor Al /Zr copolymerized alkoxide network structure. A finely divided two-phase material results which stabilizes tetragonal ZrO₂ to 1700°C and exhibits an unprecedented microstructure. During crystallization, the grain growth of ZrO₂ is coupled to the γ→α phase transformation of Al₂O₃.     

Formation and Transformation of TiO2 (Anatase) Solid Solution in the System TiO2—Al2O3

In the system TiO₂—Al₂O₃, TiO₂ (anatase, tetragonal) solid solutions crystallize at low temperatures (with up to ∼ 22 mol% Al₂O₃) from amorphous materials prepared by the simultaneous hydrolysis of titanium and aluminum alkoxides. The lattice parameter a is relatively constant regardless of composition, whereas parameter c decreases linearly with increasing Al₂O₃. At higher temperatures, anatase solid solutions transform into TiO₂ (rutile) with the formation of α-Al₂O₃. Powder characterization is studied. Pure anatase crystallizes at 220° to 360°C, and the anatase-to-rutile phase transformation occurs at 770° to 850°C.     

Low-Temperature Equilibria Among ZrO2, Tho2, and UO2

Studies made on low-hafnium-content ZrO₂, show that the monoclinic-tetragonal inversion temperature is 1170°C., and it is raised to approximately 1190°C. in the "natural" ZrO², which contains approximately 2% HfO₂. No explanation could be found for the knownmarked hysteresis during cooling, when the reverse polymorphic transformation takes dace at 1040°C. In the system ZrO₂-ThO₂ the monoclinic-tetragonal ZrO₂, inversion temperature is lowered to 1000°C., although the maximum solid solution extent of ZrO₂, in Thon and vice versa is approximately only 2% at this temperature. Below about 400°C. under hydrothermal conditions it was possible to prepare a continuous, although metastable series of solid solutions with the fluorite structurewith compositions varying from ThO₂, to nearly pure ZrO₂. Contrary to earlier work only 8 mole ZrO₂, dissolves in UO₂ and less than 4 mole of UO, in ZrO₂ at temperatures up to 13OO0C. A continuous series of solid solutions could be made between Th₂ and UO₂ at 13OO°C., and extensive defect fluorite solid solutions could be prepared between Tho₂ and U₃O₈; there is some evidence for exsolution into uranium-rich and thorium-rich members at low temperatures.     

Conversion from β-Ce2O3·11Al2O3 to α-Al2O3 in Tetragonal ZrO2 Matrix

Composites of β-Ce₂O₃·11Al₂O₃ and tetragonal ZrO₂ were fabricated by a reductive atmosphere sintering of mixed powders of CeO₂, ZrO₂ (2 mol% Y₂O₃), and Al₂O₃. The composites had microstructures composed of elongated grains of β-Ce₂O₃·11Al₂O₃ in a Y-TZP matrix. The β-Ce₂O₃·11Al₂O₃ decomposed to α-Al₂O₃ and CeO₂ by annealing at 1500°C for 1 h in oxygen. The elongated single grain of β-Ce₂O₃·11Al₂O₃ divided into several grains of α-Al₂O₃ and ZrO₂ doped with Y₂O₃ and CeO₂. High-temperature bending strength of the oxygen-annealed α-Al₂O₃ composite was comparable to the β-Ce₂O₃·11Al₂O₃ composite before annealing.     

Phase Relations in the System ZrO2-Y2O3 at Low Y2O3 Contents

Subsolidus phase relations in the low-Y₂O₃ portion of the system ZrO_2-Y₂O₃ were studied using DTA with fired samples and X-ray phase identification and lattice parameter techniques with quenched samples. Approximately 1.5% Y₂O₃ is soluble in monoclinic ZrO₂, a two-phase monoclinic solid solution plus cubic solid solution region exists to ∼7.5% Y₂O₃ below ∼500°C, and a two-phase tetragonal solid solution plus cubic solid solution exists from ∼1.5 to 7.5% Y₂O₃ from ∼500° to ∼1600°C. At higher Y₂O₃ compositions, cubic ZrO₂ solid solution occurs.     

Sintering and Crystallization of CaO–Al2O3–ZrO2–SiO2 Glasses Containing Different Amount of Al2O3

In this work several complementary techniques have been employed to carefully characterize the sintering and crystallization behavior of CaO–Al₂O₃–ZrO₂–SiO₂ glass powder compacts after different heat treatments. The research started from a new base glass 33.69 CaO–1.00 Al₂O₃–7.68 ZrO₂–55.43SiO₂ (mol%) to which 5 and 10 mol% Al₂O₃ were added. The glasses with higher amounts of alumina sintered at higher temperatures (953°C [lower amount] vs. 987°C [higher amount]). A combination of the linear shrinkage and viscosity data allowed to easily find the viscosity values corresponding to the beginning and the end of the sintering process. Anorthite and wollastonite crystals formed in the sintered samples, especially at lower temperatures. At higher temperatures, a new crystalline phase containing ZrO₂ (2CaO·4SiO₂·ZrO₂) appeared in all studied specimens.     

Microstructure and Short-Term Oxidation of Hot-Pressed Si3N4/ZrO2(+Y2O3) Ceramics

Composite ceramic materials based on Si₃N₄ and ZrO₂ stabilized by 3 mol% Y₂O₃ have been formed using aluminum isopropoxide as a precursor for the Al₂O₃ sintering aid. Densification was carred out by hot-pressing at temperatures in the range 1650° to 1800°C, and the resulting micro-structures were related to mechanical properties as well as to oxidation behavior at 1200°C. Densification at the higher temperatures resulted in a fibrous morphology of the Si₃N₄ matrix with consequent high room-temperature toughness and strength. Decomposition of the ZrO₂ grains below the oxidized surface during oxidation introduced radial stresses in the subscalar region, and from the oxidation experiments it is suggested that the ZrO₂ incorporated some N during densification.     

Hindrance of Grain Growth in Al2O3 by ZrO2 Inclusions.

Alumina and Al₂O₃/ZrO₂ (1 to 10 vol%) composite powders were mixed and consolidated by a colloidal method, sintered to >98% theoretical density at 1550°C, and subsequently heat-treated at temperatures up to 1700°C for grain-size measurements. Within the temperature range studied, the ZrO₂ inclusions exhibited sufficient self-diffusion to move with the Al₂O₃ 4-grain junctions during grain growth. Growth of the ZrO₂, inclusions occurred by coalescence. The inclusions exerted a dragging force at the 4-grain junctions to limit grain growth. Abnormal grain growth occurred when the inclusion distribution was not sufficiently uniform to hinder the growth of all Al₂O₃ grains. This condition was observed for compositions containing ≤2.5 vol% ZrO₂, where the inclusions did not fill all 4-grain junctions. Exaggerated grains consumed both neighboring grains and ZrO₂, inclusions. Grain-growth control (no abnormal grain growth) was achieved when a majority (or all) 4-grain junctions contained a ZrO₂ inclusion, viz., for compositions containing ≥5 vol% ZrO₂. For this condition, the grain size was inversely proportional to the volume fraction of the inclusions. Since the ZrO₂ inclusions mimic voids in all ways except that they do not disappear, it is hypothesized that abnormal grain growth in single-phase materials is a result of a nonuniform distribution of voids during the last stage of sintering.     

Electrical Conductivity in the ZrO2-Rich Region of Several M2O3—ZrO2 Systems

The electrical conductivity of M₂O₃-ZrO₂ compositions containing 6 to 24 mole % M₂O₃, where M represents La, Sm, Y, Yb, or Sc, was examined. Only Sm₂O₃, Y₂O₃, and Yb₂O₃ formed cubic solid solutions with ZrO₂ over most of this substitutional range. Scandia forms a wide cubic solid solution region with ZrO₂ at temperatures above 130°C whereas the cubic solid solution region at room temperature is narrow (6 to 8 mole % Sc₂O₃). Lanthana additions to ZrO₂produced no fluorite-type cubic solid solutions within the compositional range investigated. Generally, the electrical conductivity of these cubic solid solutions increased as the size of the substituted cation decreased and the electrical conductivity for each binary system attained a maximum at about 10 to 12 mole % M₂O₃.     

Influence of the Y2O3 Content and Temperature on the Mechanical Properties of Melt-Grown Al2O3–ZrO2 Eutectics

The effect of Y₂O₃ content on the flexure strength of melt-grown Al₂O₃–ZrO₂ eutectics was studied in a temperature range of 25°–1427°C. The processing conditions were carefully controlled to obtain a constant microstructure independent of Y₂O₃ content. The rod microstructure was made up of alternating bands of fine and coarse dispersions of irregular ZrO₂ platelets oriented along the growth axis and embedded in the continuous Al₂O₃ matrix. The highest flexure strength at ambient temperature was found in the material with 3 mol% Y₂O₃ in relation to ZrO₂(Y₂O₃). Higher Y₂O₃ content did not substantially modify the mechanical response; however, materials with 0.5 mol% presented a significant degradation in the flexure strength because of the presence of large defects. They were nucleated at the Al₂O₃–ZrO₂ interface during the martensitic transformation of ZrO₂ on cooling and propagated into the Al₂O₃ matrix driven by the tensile residual stresses generated by the transformation. The material with 3 mol% Y₂O₃ retained 80% of the flexure strength at 1427°C, whereas the mechanical properties of the eutectic with 0.5 mol% Y₂O₃ dropped rapidly with temperature as a result of extensive microcracking.     

Mechanical Properties of CoAl Materials with the Combined Additions of ZrO2(3Y) and Al2O3

Intermetallic CoAl powder has been prepared via self-propagating high-temperature synthesis (SHS). Dense CoAl materials (99.6% of theoretical) with the combined additions of ZrO₂(3Y) and Al₂O₃ have been fabricated via spark plasma sintering (SPS) for 10 min at 1300°C and 30 MPa. The microstructures are such that tetragonal ZrO₂ (0.3 μm) and Al₂O₃ (0.5 μm) particles are located at the grain boundaries of the CoAl (8.5 μm) matrix. Improved mechanical properties are obtained; especially the fracture toughness and the bending strength of the materials with ZrO₂(3Y)/Al₂O₃= 16/4 mol% are 3.87 MPa·m^1/2 and 1080 MPa, respectively, and high strength (>600 MPa) can be retained up to 1000°C.     

Revised Phase Diagram of the System ZrO2-CeO2 Below 1400°C

The phase diagram of the system ZrO₂-CeO₂ was rein-vestigated using hydrothermal techniques. Cubic, tetragonal, and monoclinic solid solutions are present in this system. The tetragonal solid solution decomposes to monoclinic and cubic solid solutions by a eutectoid reaction at 1050°50°C. The solubility limits of the tetragonal and cubic solid solutions are about 18 and 70 mol% CeO₂, respectively, at 1400°C, and about 16 and 80 mol% CeO₂, respectively, at 1200°C. Solubility limits of the monoclinic and cubic solid solutions are about 1.5 and 88 mol% CeO₂ at 1000°C, and 1.5 and 98 mol% CeO₂ at 800°C, respectively. The compound Ce₂Zr₃O₁₀ is not found in this system.     

Subsolidus Phase Equilibria and Ordering in the System ZrO2-Y2O3

The subsolidus phase relations in the entire system ZrO₂-Y₂O₃ were established using DTA, expansion measurements, and room- and high-temperature X-ray diffraction. Three eutectoid reactions were found in the system: ( a ) tetragonal zirconia solid solution→monoclinic zirconia solid solution+cubic zirconia solid solution at 4.5 mol% Y₂O₃ and ∼490°C, ( b ) cubic zirconia solid solutiow→δ-phase Y₄Zr₃O₁₂+hexagonalphase Y₆ZrO₁₁ at 45 mol% Y₂O₃ and ∼1325°±25°C, and ( c ) yttria C -type solid solution→wcubic zirconia solid solution+ hexagonal phase Y₆ZrO₁₁ at ∼72 mol% Y₂O₃ and 1650°±50°C. Two ordered phases were also found in the system, one at 40 mol% Y₂O₃ with ideal formula Y₄Zr₃O₁₂, and another, a new hexagonal phase, at 75 mol% Y₂O₃ with formula Y₆ZrO₁₁. They decompose at 1375° and >1750°C into cubic zirconia solid solution and yttria C -type solid solution, respectively. The extent of the cubic zirconia and yttria C -type solid solution fields was also redetermined. By incorporating the known tetragonal-cubic zirconia transition temperature and the liquidus temperatures in the system, a new tentative phase diagram is given for the system ZrO₂-Y₂O₃.     

Phase Equilibration in ZrO2-Y2O3 Alloys by Liquid-Film Migration

The tetragonal ( t ) and cubic ( c ) ZrO₂ solid solutions in two-phase ZrO₂-8 wt% Y₂O₃ ceramics have low and high solute content, respectively. Annealing samples sintered at 1600°C between 700° and 1400°C requires a change in the volume fraction of the coexisting phases, as well as their equilibrium Y₂O₃ content. The enrichment in Y₂O₃ content of the c -ZrO₂ grains is accomplished by liquid-film migration involving the ubiquitous silicate grain-boundary phase, while the volume fraction of t -ZrO₂ increases by the nucleation and growth of cap-shaped t -ZrO₂ lenses. The interfaces between the c -ZrO₂ matrix and the growing t -ZrO₂ lenses are semicoherent.     

Microstructural Evolution in a ZrO2 Wt% Y2O3 Ceramic

Several unusual microstructural features, i.e., 90° tetragonal ZrO₂ twins containing antiphase domain boundaries, tetragonal ZrO₂ precipitates in a colony morphology, and precipitate-free zones at the perimeter of cubic ZrO₂ grains containing fine tetragonal ZrO₂ precipitates, were observed in a single ZrO₂-12 wt% Y₂O₂ ceramic annealed at 1550°, 1400°, and 1250°C, respectively. The type of phase transformation responsible for each microstructural feature is described.     

Homogeneous ZrO2–Al2O3 Composite Prepared by Nano-ZrO2 Particle Multilayer-Coated Al2O3 Particles

ZrO₂–Al₂O₃ nanocomposite particles were synthesized by coating nano-ZrO₂ particles on the surface of Al₂O₃ particles via the layer-by-layer (LBL) method. Polyacrylic acid (PAA) adsorption successfully modified the Al₂O₃ surface charge. Multilayer coating was successfully implemented, which was characterized by ξ potential, particle size. X-ray diffraction patterns showed that the content of ZrO₂ in the final powders could be well controlled by the LBL method. The powders coated with three layers of nano-ZrO₂ particles, which contained about 12 wt% ZrO₂, were compacted by dry press and cold isostatically pressed methods. After sintering the compact at 1450°C for 2 h under atmosphere, a sintered body with a low pore microstructure was obtained. Scanning electron microscopy micrographs of the sintered body indicated that ZrO₂ was well dispersed in the Al₂O₃ matrix.     

Properties of (Y)ZrO2–Al2O3 and (Y)ZrO2–Al2O3–(Ti or Si)C Composites

The effect of Al₂O₃ and (Ti or Si)C additions on various properties of a (Y)TZP (yttria-stabilized tetragonal zirconia polycrystal)–Al₂O₃–(Ti or Si)C ternary composite ceramic were investigated for developing a zirconia-based ceramic stronger than SiC at high temperatures. Adding Al₂O₃ to (Y)TZP improved transverse rupture strength and hardness but decreased fracture toughness. This binary composite ceramic revealed a rapid loss of strength with increasing temperature. Adding TiC to the binary ceramic suppressed the decrease in strength at temperatures above 1573 K. The residual tensile stress induced by the differential thermal expansion between ZrO₂ and TiC therefore must have inhibited the t - → m -ZrO₂ martensitic transformation. It was concluded that a continuous skeleton of TiC prevented grain-boundary sliding between ZrO₂ and Al₂O₃. In contrast, for the ternary material containing β-SiC in place of TiC, the strength decreased substantially with increasing temperature because of incomplete formation of the SiC skeleton.