Q-Band pHEMT and mHEMT Subharmonic Gilbert Upconversion Mixers

This letter makes a comparison between Q-band 0.15 $mu{rm m}$ pseudomorphic high electron mobility transistor (pHEMT) and metamorphic high electron mobility transistor (mHEMT) stacked-LO subharmonic upconversion mixers in terms of gain, isolation and linearity. In general, a 0.15 $mu{rm m}$ mHEMT device has a higher transconductance and cutoff frequency than a 0.15 $mu{rm m}$ pHEMT does. Thus, the conversion gain of the mHEMT is higher than that of the pHEMT in the active Gilbert mixer design. The Q-band stacked-LO subharmonic upconversion mixers using the pHEMT and mHEMT technologies have conversion gain of $-$7.1 dB and $-$0.2 dB, respectively. The pHEMT upconversion mixer has an ${rm OIP}_{3}$ of $-$12 dBm and an ${rm OP}_{1 {rm dB}}$ of $-$24 dBm, while the mHEMT one shows a 4 dB improvement on linearity for the difference between the ${rm OIP}_{3}$ and ${rm OP}_{1 {rm dB}}$. Both the chip sizes are the same at 1.3 mm $times$ 0.9 mm.      

W-Band Active Down-Conversion Mixer in Bulk CMOS

A W-band (76–77 GHz) active down-conversion mixer has been demonstrated using low leakage (higher ${rm V}_{{rm T}}$) NMOS transistors of a 65-nm digital CMOS process with 6 metal levels. It achieves conversion gain of ${-}8$ dB at 76 GHz with a local oscillation power of 4 dBm (${sim-}2$ dBm after de-embedding the on-chip balun loss), and 3 dB bandwidth of 3 GHz. The SSB noise figures are 17.8–20 dB (11.3–13.5 dB after de-embedding on-chip input balun loss) between 76 and 77 GHz. ${rm IP}_{1{rm dB}}$ is ${-}6.5$ dBm and IIP3 is 2.5 dBm (${sim-}13$ and ${sim}-4$ dBm after de-embedding the on-chip balun loss). The mixer consumes 5 mA from a 1.2 V supply.      

A 36–80 GHz High Gain Millimeter-Wave Double-Balanced Active Frequency Doubler in SiGe BiCMOS

This letter presents a high conversion gain double-balanced active frequency doubler operating from 36 to 80 GHz. The circuit was fabricated in a 200 GHz ${rm f}_{rm T}$ and ${rm f}_{max}$ 0.18 $mu$m SiGe BiCMOS process. The frequency doubler achieves a peak conversion gain of 10.2 dB at 66 GHz. The maximum output power is 1.7 dBm at 66 GHz and ${-}3.9$ dBm at 80 GHz. The maximum fundamental suppression of 36 dB is observed at 60 GHz and is better than 20 dB from 36 to 80 GHz. The frequency doubler draws 41.6 mA from a nominal 3.3 V supply. The chip area of the active frequency doubler is 640 $mu$m $,times,$424 $mu$m (0.272 mm $^{2}$) including the pads. To the best of authors' knowledge, this active frequency doubler has demonstrated the highest operating frequency with highest conversion gain and output power among all other silicon-based active frequency doublers reported to date.      

An Edge Missing Compensator for Fast Settling Wide Locking Range Phase-Locked Loops

An edge missing compensator (EMC) is proposed to approach the function of an ideal PD with $pm 2 ^{N-1} times 2pi $ linear range with $N$-bit EMC. A PLL implemented with a 9-bit EMC achieves 320 MHz frequency hopping within 10 $~mu{hbox {s}}$ logarithmically which is about 2.4 times faster than the conventional design. The reference spur of the PLL is ${-}{hbox {48.7~dBc}}$ and the phase noise is ${-}hbox{88.31~dBc/Hz}$ at 10 kHz offset with $K_{rm VCO}= -$ 2 GHz/V.      

A 0.55 V 60 dB-DR Fourth-Order Analog Baseband Filter

A 0.55 V supply voltage fourth-order low-pass continuous-time filter is presented. The low-voltage operating point is achieved by an improved bias circuit that uses different opamp input and output common-mode voltages. The fourth-order filter architecture is composed by two Active- ${rm G}_{rm m}{-}{rm RC}$ biquadratic cells, which use a single opamp per-cell with a unity-gain-bandwidth comparable to the filter cut-off frequency. The $-$ 3 dB filter frequency is 12 MHz and this is higher than any other low-voltage continuous-time filter cut-off frequency. The $-$3 dB frequency can be adjusted by means of a digitally-controlled capacitance array. In a standard 0.13 $mu{rm m}$ CMOS technology with ${V}_{THN}approx 0.25 {rm V}$ and ${V}_{THP}approx 0.3 {rm V}$, the filter operates with a supply voltage as low as 0.55 V. The filter $({rm total} {rm area}=0.47 {rm mm}^{2})$ consumes 3.4 mW. A 8 dBm-in-band IIP3 and a 13.3 dBm-out-of-band IIP3 demonstrate the validity of the proposal.      

A 1 V 23 GHz Low-Noise Amplifier in 45 nm Planar Bulk-CMOS Technology With High-$Q$ Above-IC Inductors

A 23 GHz electrostatic discharge-protected low-noise amplifier (LNA) has been designed and implemented by 45 nm planar bulk-CMOS technology with high-$Q$ above-IC inductors. In the designed LNA, the structure of a one-stage cascode amplifier with source inductive degeneration is used. All high- $Q$ above-IC inductors have been implemented by thin-film wafer-level packaging technology. The fabricated LNA has a good linearity where the input 1 dB compression point $({rm IP}_{{-}1~{rm dB}})$ is ${- 9.5}~{rm dBm}$ and the input referred third-order intercept point $(P _{rm IIP3})$ is ${+ 2.25}~{rm dBm}$. It is operated with a 1 V power supply drawing a current of only 3.6 mA. The fabricated LNA has demonstrated a 4 dB noise figure and a 7.1 dB gain at the peak gain frequency of 23 GHz, and it has the highest figure-of-merit. The experimental results have proved the suitability of 45 nm gate length bulk-CMOS devices for RF ICs above 20 GHz.      

A Noise-Coupled Time-Interleaved Delta-Sigma ADC With 4.2 MHz Bandwidth, ${-}$ 98 dB THD, and 79 dB SNDR

This paper describes a wideband high-linearity $Delta Sigma $ ADC. It uses noise coupling combined with time interleaving. Two versions of a two-channel time-interleaved noise-coupled $Delta Sigma $ ADC were realized in a 0.18- $mu{hbox {m}}$ CMOS technology. Noise coupling between the channels increases the effective order of the noise-shaping loops, provides dithering, and prevents tone generation in all loops. Time interleaving enhances the effects of noise coupling. Using a 1.5 V supply, the device achieved excellent linearity (${rm SFDR} > {hbox {100~dB}}$, ${rm THD}= -{hbox {98~dB}}$) and an SNDR of 79 dB in a 4.2 MHz signal band.      

Experimental Demonstration of Deeply-Etched SiO$_{2}$ Ridge Optical Waveguides and Devices

Deeply-etched ${hbox{SiO}}_{2}$ optical ridge waveguides are fabricated and characterized. A detailed discussion of the fabrication process (especially for the deep etching process) is presented. The measured propagation losses for the fabricated waveguides with different core widths range from $0.33sim {hbox {0.81}}~{hbox {dB}}/{hbox {mm}}$. The loss is mainly caused by the scattering due to the sidewall roughness. The losses in bending sections are also characterized, which show the possibility of realizing a small bending radius (several tens of microns). 1 $,times {rm N}$ ( ${rm N}=2$, 4, 8) multimode interference couplers based on the deeply-etched ${hbox{SiO}}_{2}$ ridge waveguide are also fabricated and show fairly good performances.      

A $K$ -Band CMOS Distributed Doubler With Current-Reuse Technique

A $K$-band distributed frequency doubler is developed in 0.18 $mu{rm m}$ CMOS technology. This doubler combines the distributed topology for broadband characteristics and current-reuse technique to improve the conversion gain. The high-pass drain line and high-pass inter-stage matching network are used to obtain a good fundamental rejection. A measured conversion gain of better than ${- 12.3}~{rm dB}$ is obtained, and the fundamental rejection is better than 30 dB for the output frequency between 18 and 26 GHz. The dc power consumption is 10.5 mW with a chip size of 0.55$,times,$0.5 ${rm mm}^{2}$.      

2 MHz AO $Q$ -switched ${rm TEM}_{00}$ Grazing Incidence Laser With 3 at.% Neodymium Doped Nd:YVO$_{4}$

We present a detailed experimental and theoretical study of the ultrahigh repetition rate AO $Q$ -switched ${rm TEM}_{00}$ grazing incidence laser. Up to 2.1 MHz $Q$-switching with ${rm TEM}_{00}$ output of 8.6 W and 2.2 MHz $Q$ -switching with multimode output of 10 W were achieved by using an acousto-optics $Q$ -switched grazing-incidence laser with optimum grazing-incidence angle and cavity configuration. The crystal was 3 at.% neodymium doped Nd:YVO$_{4}$ slab. The pulse duration at 2 MHz repetition rate was about 31 ns. The instabilities of pulse energy at 2 MHz repetition rate were less than ${pm}6.7hbox{%}$ with ${rm TEM}_{00}$ operation and ${pm}3.3hbox{%}$ with multimode operation respectively. The modeling of high repetition rate $Q$-switched operation is presented based on the rate equation, and with the solution of the modeling, higher pump power, smaller section area of laser mode, and larger stimulated emission cross section of the gain medium are beneficial to the $Q$-switched operation with ultrahigh repetition rate, which is in consistent with the experimental results.      

Improved Microwave Noise Performance by SiN Passivation in AlGaN/GaN HEMTs on Si

Effects of silicon nitride (SiN) surface passivation by plasma enhanced chemical vapor deposition (PECVD) on microwave noise characteristics of AlGaN/GaN HEMTs on high-resistivity silicon (HR-Si) substrate have been investigated. About 25% improvement in the minimum noise figure $(NF_{min})$ (0.52 dB, from 2.03 dB to 1.51 dB) and 10% in the associate gain $(G_{rm a})$ (1.0 dB, from 10.3 dB to 11.3 dB) were observed after passivation. The equivalent circuit parameters and noise source parameters (including channel noise coefficient $(P)$, gate noise coefficient $(R)$, and their correlation coefficient $(C)$ ) were extracted. $P$ , $R$ and $C$ all increased after passivation and the increase of C contributes to the decrease of the noise figure. It was found that the improved microwave small signal and noise performance is mainly due to the increase of the intrinsic transconductance $(g_{{rm m}0})$ and the decrease of the extrinsic source resistance $(R_{rm s})$.      

A Fully Integrated 5 GHz Low-Voltage LNA Using Forward Body Bias Technology

A fully integrated 5 GHz low-voltage and low-power low noise amplifier (LNA) using forward body bias technology, implemented through a 0.18 $mu{rm m}$ RF CMOS technology, is demonstrated. By employing the current-reused and forward body bias technique, the proposed LNA can operate at a reduced supply voltage and power consumption. The proposed LNA delivers a power gain (S21) of 10.23 dB with a noise figure of 4.1 dB at 5 GHz, while consuming only 0.8 mW dc power with a low supply voltage of 0.6 V. The power consumption figure of merit $(FOM_{1})$ and the tuning-range figure of merit $(FOM_{2})$ are optimal at 12.79 dB/mW and 2.6 ${rm mW}^{-1}$, respectively. The chip area is 0.89 $,times,$0.89 ${rm mm}^{2}$.      

Electrical Instability of RF Sputter Amorphous In-Ga-Zn-O Thin-Film Transistors

Bias-temperature-stress (BTS) induced electrical instability of the RF sputter amorphous In-Ga-Zn-O (a-IGZO) thin-film transistors (TFTs) was investigated. Both positive and negative BTS were applied and found to primarily cause a positive and negative voltage shift in transfer $(I _{rm DS} -V _{rm GS})$ characteristics, respectively. The time evolution of bulk-state density $(N _{rm BS})$ and characteristic temperature of the conduction-band-tail-states $(T _{G})$ are extracted. Since both values showed only minor changes after BTS, the results imply that observed shift in TFT $I _{rm DS} -V _{rm GS}$ curves were primarily due to channel charge injection/trapping rather than defect states creation. We also demonstrated the validity of using stretch-exponential equation to model both positive and negative BTS induced threshold voltage shift $(Delta V _{rm th})$ of the a-IGZO TFTs. Stress voltage and temperature dependence of $Delta V _{rm th}$ evolution are described.      

InGaAs/GaAs 0.98- $mu{hbox {m}}$ Low-Divergence Central-Lobe Semiconductor Lasers With $delta$ -Doped Resonant Tunneling Quantum Wells

In this paper, we describe a new structure design for producing low-threshold, high-efficiency, and high-brightness 0.98-$mu{hbox {m}}$ lasers. In this structure, we incorporated a self-discriminating weak optical confinement asymmetrical waveguide coupled to passive waveguides, and an active region based on three InGaAs quantum wells (QWs) coupled to Te n-type $delta$-doping. Optimized coupling between the $delta$-doping and the three QWs, together with waveguide optimization and doping profile optimization, yields $J_{rm th}=98 {hbox {A/cm}}^{2}$ per QW, ${T}_{0}=80;^{circ}hbox{C}$, and a far-field central lobe angle of $sim 10^{circ}$.      

Single- and Dual-Polarized Tunable Slot-Ring Antennas

Single- and dual-polarized slot-ring antennas with wideband tuning using varactor diodes have been demonstrated. The single-polarized antenna tunes from 0.95 to 1.8 GHz with better than ${-}13$ dB return loss. Both polarizations of the dual-polarized antenna tune from 0.93 to 1.6 GHz independently with better than ${-}10$ dB return loss and $> !20!$ dB port-to-port isolation over most of the tuning range. The capacitance of the varactor diodes varies from 0.45 to 2.5 pF, and the antennas are printed on 70 $,times,$70 $,times,$0.787 mm ${^3}$ substrates with ${epsilon_{rm r} = 2.2}$. The dual-polarized slot-ring antenna can either be made both frequency- and polarization-agile simultaneously, or can operate at two independent frequencies on two orthogonal polarizations. To our knowledge, this is the first dual-polarized tunable antenna with independent control of both polarizations over a 1.7:1 frequency range.      

A 3–10 GHz CMOS UWB Low-Noise Amplifier With ESD Protection Circuits

A low-power fully integrated low-noise amplifier (LNA) with an on-chip electrostatic-static discharge (ESD) protection circuit for ultra-wide band (UWB) applications is presented. With the use of a common-gate scheme with a ${rm g}_{rm m}$ -boosted technique, a simple input matching network, low noise figure (NF), and low power consumption can be achieved. Through the combination of an input matching network, an ESD clamp circuit has been designed for the proposed LNA circuit to enhance system robustness. The measured results show that the fabricated LNA can be operated over the full UWB bandwidth of 3.0 to 10.35 GHz. The input return loss $({rm S}_{11})$ and output return loss $({rm S}_{22})$ are less than ${-}8.3$ dB and ${-}9$ dB, respectively. The measured power gain $({rm S}_{21})$ is $11 pm 1.5$ dB, and the measured minimum NF is 3.3 dB at 4 GHz. The dc power dissipation is 7.2 mW from a 1.2 V supply. The chip area, including testing pads, is 1.05 mm$,times,$ 0.73 mm.      

A Low Loss High Isolation DC-60 GHz SPDT Traveling-Wave Switch With a Body Bias Technique in 90 nm CMOS Process

In this letter, a low loss high isolation broadband single-port double-throw (SPDT) traveling-wave switch using 90 nm CMOS technology is presented. A body bias technique is utilized to enhance the circuit performance of the switch, especially for the operation frequency above 30 GHz. The parasitic capacitance between the drain and source of the NMOS transistor can be further reduced using the negative body bias technique. Moreover, the insertion loss, the input 1 dB compression point (${rm P} _{{1}~{rm dB}}$), and the third-order intermodulation (IMD3) of the switch are all improved. With the technique, the switch demonstrates an insertion loss of 3 dB and an isolation of better than 48 dB from dc to 60 GHz. The chip size of the proposed switch is 0.68 $,times,$0.87 ${rm mm}^{2}$ with a core area of only 0.32$,times,$0.21 ${rm mm}^{2}$.      

A Biphase Modulator Circuit for Impulse Radio-UWB Applications

This letter presents a circuit to provide binary phase shift keying to ultra-wideband (UWB) impulse transmitters. The circuit is based on a Gilbert-cell multiplier and uses active on-chip balun and unbalanced-to-balanced converters for single-ended to single-ended operation. Detailed measurements of the circuit show a gain ripple of $pm 1~{rm dB}$ at an overall gain of $-2~{rm dB}$, an input reflection below $-12~{rm dB}$, an output reflection below $-18~{rm dB}$, a group delay variation below 6 ps and a $-1~{rm dB}$ input compression point of more than 1 dBm in both switching states over the full 3.1–10.6 GHz UWB frequency range. A time domain measurement verifies the switching operation using an FCC-compliant impulse generator. The circuit is fabricated in a $0.8~mu {rm m}$ Si/SiGe HBT technology, consumes 31.4 mA at a 3.2 V supply and has a size of $510 times 490~mu{rm m}^{2}$ , including pads. It can be used in UWB systems using pulse correlation reception or spectral spreading.      

Novel Composite Phase-Shifting Transmission-Line and Its Application in the Design of Antenna Array

A novel composite phase-shifting transmission line (TL) with designable characteristics is presented, which can be used to achieve arbitrary phase of the transmission coefficient at any required frequency with a certain length of the TL. An empirical formula is given of the relationship between the phase and physical length of the composite TL at a required frequency. A sample of 0$^{circ}$ phase-shifting TL is designed in details, and is verified by the full-wave simulation. At the required frequency of 5 GHz, the amplitude of ${rm S}_{21}$ is equal to $-0.23~{rm dB}$ with a phase of $-0.467^{circ}$. The electric length is only $0.212lambda_{0}$ , which has been decreased by 68.5% compared to the conventional microstrip line. Using the proposed composite TL, an antenna array is designed with two radiation patches excited by the novel series feed-line. The detailed procedure of such design is presented. The lowest reflection coefficient is exactly achieved at the required frequency of 5 GHz. The maximum radiation is obtained at $theta_{0}=0^{circ}$ , which indicates that the 0$^{circ}$ phase-shifting TL works very well. The sample is also fabricated and good agreements between simulation and measurement results are obtained.      

Design of a Beam Switching/Steering Butler Matrix for Phased Array System

A compact broadband 8-way Butler matrix integrated with tunable phase shifters is proposed to provide full beam switching/steering capability. The newly designed multilayer stripline Butler matrix exhibits an average insertion loss of 1.1 dB with amplitude variation less than $pm$2.2 dB and an average phase imbalance of less than 20.7$^{circ}$ from 1.6 GHz to 2.8 GHz. The circuit size is only $160times 100 {rm mm}^{2}$, which corresponds to an 85% size reduction compared with a comparable conventional microstrip 8-way Butler matrix. The stripline tunable phase shifter is designed based on the asymmetric reflection-type configuration, where a Chebyshev matching network is utilized to convert the port impedance from 50 $Omega$ to 25 $Omega$ so that a phase tuning range in excess of 120$^{circ}$ can be obtained from 1.6 GHz to 2.8 GHz. To demonstrate the beam switching/steering functionality, the proposed tunable Butler matrix is applied to a 1 $times$ 8 antenna array system. The measured radiation patterns show that the beam can be fully steered within a spatial range of 108 $^{circ}$.