Phase‐Composition‐Dependent Piezoelectric and Electromechanical Strain Properties in (Bi1/2Na1/2)TiO3–Ba(Ni1/2Nb1/2)O3 Lead‐Free Ceramics

New lead‐free perovskite solid solution ceramics of (1 ? x)(Bi_1/2Na_1/2)TiO₃–xBa(Ni_1/2Nb_1/2)O₃[(1?x)BNT–xBNN,x = 0.02–0.06) were prepared and their dielectric, ferroelectric, piezoelectric, and electromechanical properties were investigated as a function of the BNN content. The X‐ray diffraction results indicated that the addition of BNN has induced a morphotropic phase transformation from rhombohedral to pseudocubic symmetry approximately at x = 0.045, accompanying an evolution of dielectric relaxor behavior as characterized by enhanced dielectric diffuseness and frequency dispersion. In the proximity of the ferroelectric rhombohedral and pseudocubic phase coexistence zone, the x = 0.045 ceramics exhibited optimal piezoelectric and electromechanical coupling properties of d₃₃~121 pC/N and k_p~0.27 owing to decreased energy barriers for polarization switching. However, further addition of BNN could cause a decrease in freezing temperatures of polar nanoregions till the coexistence of nonergodic and ergodic relaxor phases occurred near room temperature, especially for the x = 0.05 sample which has negligible negative strains and thus show the maximum electrostrain of 0.3% under an external electric field of 7 kV/mm, but almost vanished piezoelectric properties. This was attributed to the fact that the induced long‐range ferroelectric order could reversibly switch back to its original ergodic state upon removal of external electric fields.     

Normal‐Relaxor‐Diffuse Ferroelectric Phase Transition and Electrical Properties of Bi(Mg1/2Ti1/2)3–PbZrO3–PbTiO3 Solid Solution Ceramics Near the Morphotropic Phase Boundary

Perovskite‐type xBi(Mg_1/2Ti_1/2)O₃–(0.56 ? x)PbZrO₃–0.44PbTiO₃ (xBMT–PZ–PT) ternary solid solution ceramics were synthesized via a conventional solid‐state reaction method. The phase transition behaviors, dielectric, ferroelectric, and piezoelectric properties were investigated as a function of the BMT content. The X‐ray diffraction analysis showed that the tetragonality of xBMT–PZ–PT was enhanced with increasing the BMT content, and a morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases was identified approximately in the composition of x = 0.08. In addition, the dielectric diffuseness and frequency dispersion behavior were induced with the addition of BMT and a normal‐relaxor‐diffuse ferroelectric transformation was observed from the PZ‐rich side to the BMT‐rich side. The electrical properties of xBMT–PZ–PT ceramics exhibit obviously compositional dependence. The x = 0.08 composition not only possessed the optimum properties with ε^T₃₃/ε₀ = 1450, Q_m = 69, d₃₃ = 390 pC/N, k_p = 0.46, P_r = 30 μC/cm², E_c = 1.4 kV/mm, T_c = 325°C, and a strain of 0.174% (d₃₃^* = 436 pm/V) under an electric field of 4 kV/mm as a result of the coexistence of two ferroelectric phases near the MPB, but also owned a good thermal‐depolarization behavior with a d₃₃ value of >315 pC/N up to 290°C and a frequency‐insensitive strain behavior.     

Giant electromechanical strain response in lead‐free SrTiO3‐doped (Bi0.5Na0.5TiO3–BaTiO3)–LiNbO3 piezoelectric ceramics

Lead‐free 0.985[(0.94?x)Bi_0.5Na_0.5TiO₃–0.06BaTiO₃–xSrTiO₃]–0.015LiNbO₃ [(BNT–BT–xST)–LN, x=0‐0.05] piezoelectric ceramics were prepared using a conventional solid‐state reaction method. It was found that the long‐range ferroelectric order in the unmodified (BNT–BT)–LN ceramic was disrupted and transformed into the ergodic relaxor phase with the ST substitution, which was well demonstrated by the dramatic decrease in remnant polarization (P_r), coercive field (E_c), negative strain (S_neg) and piezoelectric coefficient (d₃₃). However, the degradation of the ferroelectric and piezoelectric properties was accompanied by a significant increase in the usable strain response. The critical composition (BNT–BT–0.03ST)–LN exhibited a maximum unipolar strain of ~0.44% and corresponding normalized strain, S_max/E_max of ~880 pm/V under a moderate field of 50 kV/cm at room temperature. This giant strain was associated with the coexistence of the ferroelectric and ergodic relaxor phases, which should be mainly attributed to the reversible electric‐field‐induced transition between the ergodic relaxor and ferroelectric phases. Furthermore, the large field‐induced strain showed relatively good temperature stability; the S_max/E_max was as high as ~490 pm/V even at 120°C. These findings indicated that the (BNT–BT–xST)–LN system would be a suitable environmental‐friendly candidate for actuator applications.     

Dielectric and Piezoelectric Properties of (1−x)K0.5Bi0.5TiO3–xBa(Ti0.8Zr0.2)O3 Ceramics

The properties of relaxor ceramics in the compositional series (1?x)K_0.5Bi_0.5TiO₃–xBa(Ti_0.8Zr_0.2)O₃ have been investigated. Values of T_m, the temperature of maximum relative permittivity, decreased from 380°C at x = 0.0 to below room temperature for x > 0.7. Compositions x = 0.1 and 0.2 were piezoelectric and ferroelectric. The maximum value of d₃₃ piezoelectric charge coefficient, 130 pC/N, and strain, 0.14%, occurred at x = 0.1. Piezoelectric properties of x = 0.1 were retained after thermal cycling from room temperature to 220°C, consistent with results from high‐temperature X‐ray diffraction indicating a transition to single‐phase cubic at ~300°C.     

The Composition and Temperature‐Dependent Structure Evolution and Large Strain Response in (1−x)(Bi0.5Na0.5)TiO3−xBa(Al0.5Ta0.5)O3 Ceramics

The (1?x) (Bi_0.5Na_0.5)TiO₃?xBa(Al_0.5Ta_0.5)O₃((1?x)BNT‐xBAT) lead‐free piezoceramics was fabricated using a conventional solid‐state reaction method. The temperature and composition‐dependent strain behavior, dielectric, ferroelectric (FE), piezoelectric, and pyroelectric properties have been systematically investigated to develop lead‐free piezoelectric materials with large strain response for actuator application. As the BAT content increased, the FE order is disrupted resulting in a degradation of the remanent polarization, coercive field, and the depolarization temperature (T_d). A large strain of 0.36% with normalized strain d₃₃* = 448pm/V was obtained for the optimum composition x = 0.045 at room temperature. The bipolar and unipolar strains for the compositions x = 0.035 and x = 0.04 reach almost identical maximum values when the temperature is in the vicinity of their respective depolarization temperature (T_d). The Raman‐spectra analysis, macroscopic properties, thermal depolarization results, and temperature‐dependent relationships of both polarization and strain demonstrated that the origin of the large strain response for this investigated system is attributed to a field‐induced relaxor to FE phase transformation.     

Structure‐property relationships in BiScO3–PbTiO3–PbMg1/3Nb2/3O3 ceramics near the morphotropic phase boundary

The phase structure, dielectric, ferroelectric, and piezoelectric properties of (1?2x)BiScO₃–xPbTiO₃–xPbMg_1/3Nb_2/3O₃ ceramics (x = 0.30‐0.46) were studied. It was found that an increase in x leads to a structural phase transition between the rhombohedral and tetragonal phase via an intermediate monoclinic phase and to a crossover from the nonergodic relaxor state to the ferroelectric one. It was proposed that at x > 0.42 the phase transition changes from second to first order. The assumption about the existence of a tricritical point on the phase diagram at x ≈ 0.42 with the enhanced dielectric response has been made. The observed structure‐property relationships of the studied solid solutions are discussed. It is shown that the solid solutions with x = 0.42 are characterized by the high piezoelectric parameters (d₃₃ = 509 pC/N, d₃₁ = ?178 pC/N, d_h = 153 pC/N), which makes possible their applications in sonar equipment.     

Phase coexistence and large piezoelectricity in BaTiO3‐CaSnO3 lead‐free ceramics

Ferroelectric phase coexistence was constructed in (1?x)BaTiO₃‐xCaSnO₃ lead‐free ceramics, and its relationship with the piezoelectricity of the materials was investigated to ascertain potential factors for strong piezoelectric response. It is found that the addition of CaSnO₃ caused a series of phase transitions in the (1?x)BaTiO₃‐xCaSnO₃ ceramics, and a ferroelectric coexistence of rhombohedral, orthorhombic, and tetragonal phases is formed at x = 0.08, where the ceramics exhibit the lowest energy barrier and consequently facilitate the polarization rotation and extension, resulting in the optimal piezoelectricity of d₃₃ and k_p values of 550 pC/N and 0.60, respectively. Our study provides an intuitive insight to understand the origin of high piezoelectricity in the ceramics with the coexistence of multiferroelectric phases.     

Composition‐ and Temperature‐Dependent Large Strain in (1−x)(0.8Bi0.5Na0.5TiO3–0.2Bi0.5K0.5TiO3)– xNaNbO3 Ceramics

Ternary solid solutions of (1 ? x)(0.8Bi_0.5Na_0.5TiO₃–0.2Bi_0.5K_0.5TiO₃)– xNaNbO₃ (BNKT–xNN) lead‐free piezoceramics were fabricated using a conventional solid‐state reaction method. Pure BNKT composition exhibited an electric‐field‐induced irreversible structural transition from pseudocubic to ferroelectric rhombohedral phase at room temperature. Accompanied with the ferroelectric‐to‐relaxor temperature T_F‐R shifted down below room temperature as the substitution of NN, a compositionally induced nonergodic‐to‐ergodic relaxor transition was presented, which featured the pinched‐shape polarization and sprout‐shape strain hysteresis loops. A strain value of ~0.445% (under a driving field of 55 kV/cm) with large normalized strain of ~810 pm/V was obtained for the composition of BNKT–0.04NN, and the large strain was attributed to the reversible electric‐field‐induced transition between ergodic relaxor and ferroelectric phase.     

Remarkably High‐Temperature Stability of Bi(Fe1−xAlx)O3–BaTiO3 Solid Solution with Near‐Zero Temperature Coefficient of Piezoelectric Properties

The 0.72Bi(Fe_1?xAl_x)O₃–0.28BaTiO₃ (x = 0, 0.01, 0.03, 0.05, and 0.07, abbreviated as BFAx–BT) lead‐free high‐temperature ceramics were prepared by the conventional ceramic processing. Systematic investigation on the microstructures, crystalline structures, dielectric and piezoelectric properties, and high‐temperature stability of piezoelectric properties was carried out. The crystalline structures of BFAx–BT ceramics evolve from rhombohedral structure with x < 0.01 to the coexistence of rhombohedral structure and pseudocubic phases with x ≈ 0.01, finally to pseudocubic phases when x > 0.03. Remarkably high‐temperature stability with near‐zero temperature coefficient of piezoelectric properties (TCk_p), together with improved piezoelectric properties has been achieved for x = 0.01 BFAx–BT ceramics. The BFAx–BT(x = 0.01) ceramics simultaneously show the excellent piezoelectric properties of d₃₃ = 151 pC/N, k_p = 0.31 and super‐high‐temperature stability of T_d = 420°C, TCk_p = 1 × 10^?4. It is considered that the observed strong piezoelectricity and remarkably high‐temperature stability should be ascribed to the phase coexistence of rhombohedral and pseudocubic phases. The rhombohedral phases have a positive TCk_p value and the pseudocubic phases possess a negative TCk_p value. Thus, the TCk_p value of BFAx–BT ceramics can be tuned by composition of x.     

Novel BiFeO3–BaTiO3–Ba(Mg1/3Nb2/3)O3 Lead‐Free Relaxor Ferroelectric Ceramics for Energy‐Storage Capacitors

A novel lead‐free relaxor ferroelectric ceramic of (0.67?x)BiFeO₃–0.33BaTiO₃–xBa(Mg_1/3Nb_2/3)O₃ [(0.67?x)BF–0.33BT–xBMN, x = 0–0.1] was prepared by a solid‐state reaction method. A relatively high maximum polarization P_max of 38 μC/cm² and a low remanent polarization P_r of 5.7 μC/cm² were attained under 12.5 kV/mm in the x = 0.06 sample, leading to an excellent energy‐storage density of W ~1.56 J/cm³ and a moderate energy‐storage efficiency of η ~75%. Moreover, a good temperature stability of the energy storage was obtained in the x = 0.06 sample from 25°C to 190°C. The achievement of these characteristics was basically attributed to an electric field induced reversible ergodic to ferroelectric phase transition owing to similar free energies near a critical freezing temperature. The results indicate that the (0.67?x)BF–0.33BT–xBMN lead‐free realxor ferroelectric ceramic could be a promising dielectric material for energy‐storage capacitors.     

Enhanced Multiferroic and Magnetocapacitive Properties of (1 − x)Ba0.7Ca0.3TiO3–xBiFeO3 Ceramics

The structures, Curie temperature, dielectric relaxor behaviors, ferroelectricity, ferromagnetism, and magnetocapacitance of the (1?x)Ba_0.70Ca_0.30TiO₃–xBiFeO₃ [(1?x)BCT–xBF, x = 0–0.90] solid solutions have been systematically investigated. The ceramics have coexisted tetragonal (T) and orthorhombic (O) phases when x ≤ 0.06, coexisted pseudocubic (PC) and O phases when x = 0.065, coexisted cubic and O phases when 0.07 ≤ x ≤ 0.12, PC phase when 0.21 ≤ x ≤ 0.42, coexisted T and rhombohedral (R) phases when 0.52 ≤ x ≤ 0.70, and R phase when x ≥ 0.75. Significantly, composition‐dependent microstructures and Curie temperature are observed, the average grain size increases from 1.9 μm for x = 0, reaches 12.0 μm for x = 0.67, and then decreases to 1.3 μm for x = 0.90. At room temperature, the ceramics with x = 0.42–0.70 show piezoelectric properties and multiferroic behaviors, characterized by the polarization‐electric field, polarization current intensity–electric field, and magnetization–magnetic field curves, the composition with x = 0.67 has maximum polarization, remnant polarization, maximum magnetization, and remnant magnetization of 15.0 μC/cm², 9.1 μC/cm², 0.33 emu/g, and 0.14 emu/g, respectively. In addition, the magnetocapacitance is evidenced by the increased relative dielectric constant with increasing the applied magnetic field (H). With ΔH = 8 kOe, the composition with x = 0.67 shows the largest values of (ε_r(H) ? ε_r(0))/ε_r(0) = 2.96% at room temperature. The structure–property relationship is discussed intensively.     

NaNbO3‐BaTiO3‐NaSbO3 lead and potassium‐free ceramics with thermally stable small‐signal piezoelectric properties

A new lead‐potassium‐free ceramic of (0.9‐x)NaNbO₃‐0.1BaTiO₃‐xNaSbO₃ (NN‐BT‐xNS) was successfully prepared via a solid‐state reaction method. The microstructure, phase structure, dielectric, ferroelectric, and piezoelectric properties were investigated as a function of NS content. The substitution of NS for NN was found to dramatically change the grain morphology from cube‐like grains typical for alkaline niobate‐based ceramics to conventional sphere‐like grains especially for Pb‐based perovskite ceramics. A normal to relaxor ferroelectric phase transformation was accompanied by a tetragonal (T) to rhombohedral (R) phase transition. A composition‐temperature phase diagram demonstrated a vertical morphotropic phase boundary between T and R phases in the composition range of x=0.03‐0.04, where optimum electrical properties of d₃₃=252 pC/N, k_p=36%, Q_m=168, =2063, and T_c=109°C were obtained in the x=0.035 ceramic sintered at 1260°C. Particularly, excellent temperature insensitivity of small‐signal piezoelectric properties suggested large application potentials in various actuators and sensors in comparison with other typical lead‐free materials.     

Large Piezoelectric Response and Polarization in Relaxor Ferroelectric PbTiO3–Bi(Ni1/2Zr1/2)O3

New binary system (1?x) PbTiO₃?xBi(Ni_1/2Zr_1/2)O₃ (PT–100x BNZ) with x ≤ 0.45 were synthesized via solid‐state reaction route. A morphotropic phase boundary (MPB) was identified around x = 0.40 by X‐ray diffraction (XRD) method. The ceramics with MPB composition exhibit enhanced ferroelectric properties. A large piezoelectric coefficient (d₃₃) up to 400 pC/N was obtained for the PT–40BNZ, which is comparable with the PbTiO₃–BiScO₃ (PT–BS, 450 pC/N).The frequency dependence of dielectric permittivity of PT–40BNZ shows characteristic of a strong relaxor feature and a transition temperature around 290°C (1 MHz). Temperature effect on the unipolar strain was also investigated. The present system with high d₃₃ is a competitive piezoelectric material, as no expensive oxide is used here compared with the PT–BS.     

Effect of BiMeO3 on the Phase Structure,Ferroelectric Stability,and Properties of Lead‐Free Bi0.5(Na0.80K0.20)0.5TiO3 Ceramics

The effects of BiMeO₃ (Me = Fe, Sc, Mn, Al) addition on the phase transition and electrical properties of Bi_0.5(Na_0.80K_0.20)_0.5TiO₃ (BNKT20) lead‐free piezoceramics were systematically investigated. Results showed that addition of BiFeO₃ into BNKT20 induces a phase transition from tetragonal–rhombohedral coexisted phases to a tetragonal phase with the observation of enhanced piezoelectric properties (d₃₃ = 150 pC/N for 0.02BiFeO₃). BiScO₃, BiMnO₃, and BiAlO₃ substitutions into BNKT20 induce a phase transition from coexistence of ferroelectric tetragonal and rhombohedral to a relaxor pseudocubic with a significant disruption of the long‐range ferroelectric order, and correspondingly adjusts the ferroelectric–relaxor transition point T_F–R to room temperature. Accordingly, large accompanying normalized strains of 0.34%–0.36% are obtained near the ferroelectric–relaxor phase boundary, and the mergence of large strain response can be ascribed to a reversible field‐induced ergodic relaxor‐to‐ferroelectric phase transformation. Moreover, our study also revealed that the composition located at the ferroelectric–relaxor phase boundary where the strain response is consistently derivable shifts to a BNKT20‐rich composition as the tolerance factor t of the end‐member BiMeO₃ increases, and this relationship is expected to provide a guideline for designing high‐performance (Bi_0.5Na_0.5)TiO₃‐based materials by searching the ferroelectric–relaxor phase boundary.     

Effects of A1/A2‐Sites Occupancy upon Ferroelectric Transition in (SrxBa1−x)Nb2O6 Tungsten Bronze Ceramics

The dielectric and ferroelectric characteristics of (Sr_xBa_1?x)Nb₂O₆ unfilled tungsten bronze ceramics have been investigated together with the structure. The dielectric and ferroelectric characteristics of the present ceramics vary significantly with x, and the A1/A2‐sites occupancy has been determined as the primary parameter governing this variation tendency. Ba ions tend to occupy A2‐sites, Sr ions tend to occupy A1‐sites, and one A1‐site is empty. When the ratio of Sr/Ba is close to 1:4 (where four A2‐sites are just occupied by Ba ions, and one A1‐site is occupied by Sr ion while another A1‐site is empty), the normal ferroelectric transition is observed with one anomaly in the tanδ–T curve (x = 0.25). When the ratio of Sr/Ba is far away from 1:4, the typical relaxor behavior is indicated together with three anomalies in the tanδ–T curve (x = 0.75). The incommensurate oxygen octahedral tilting and A‐site random distribution are considered to be the structure origins for the relaxor ferroelectricity and low temperature dielectric relaxations.     

The Relationship Between Phase Structure and Electrical Properties in (1 − x)(Bi0.5Na0.5TiO3–Ba0.5K0.5TiO3–BaTiO3)‐ xK0.5Na0.5NbO3 Quaternary Lead‐Free Piezoelectric Ceramics

(1 ? x)(0.85Bi_0.5Na_0.5TiO₃–0.11Ba_0.5K_0.5TiO₃–0.04BaTiO₃)‐ xK_0.5Na_0.5NbO₃ lead‐free piezoelectric ceramics with x = 0.00, 0.02, 0.03, 0.04, 0.05, and 0.10 were prepared by a conventional solid state method. A coexistence of rhombohedral (R) and tetragonal (T) phases was found in the system, which tended to evolve into pseudocubic symmetry when x increases. The x = 0.04 sample exhibited improved electrical properties: the dielectric constant ε_r = 1900 with the low loss tangents 0.06, the S_max/E_max of ~400 and ~460 pm/V under unipolar and bipolar electric field, respectively. Meanwhile, piezoelectric constant d₃₃ still maintained ~160 pC/N. These could be owed to the formation of polar nanoregions for relaxor phase.     

Large strain response with low driving field in Bi1/2Na1/2TiO3–Bi1/2K1/2TiO3–Bi(Mg2/3Nb1/3)O3 ceramics

The (1?x)(0.8Bi_1/2Na_1/2TiO₃–0.2Bi_1/2K_1/2TiO₃)?xBiMg_2/3Nb_1/3O₃ (100xBMN) ternary solid solutions were designed and prepared using a conventional solid‐state reaction. Temperature and compositional dependent ferroelectric, piezoelectric, dielectric features, and structural evolution were systematically studied. At the critical composition of 2BMN, a large bipolar strain of 0.43% was achieved at 55 kV/cm, and the normalized strain reaches to 862 pm/V at a low driving electric field of 40 kV/cm. It was found that the substitution of BiMg_2/3Nb_1/3O₃ induces a transformation from ferroelectric to relaxor phase by disrupting the long range ferroelectric order. Therefore, as the external electric field was applied, a relaxor‐ferroelectric phase transition will be induced. This is contributed to the giant strain. The results above suggest that such a ternary composition is a promising candidate for application to actuator.     

Dielectric Relaxor Evolution and Frequency‐Insensitive Giant Strains in (Bi0.5Na0.5)TiO3‐Modified Bi(Mg0.5Ti0.5)O3–PbTiO3 Ferroelectric Ceramics

The 0.45Bi(Mg_0.5Ti_0.5)O₃–(0.55 ? x)PbTiO₃–x(Bi_0.5Na_0.5)TiO₃ (BMT–PT–xBNT) ternary solid solution ceramics were prepared via a conventional solid‐state reaction method; the evolution of dielectric relaxor behavior and the electrostrain features were investigated. The XRD and dielectric measurements showed that all studied compositions own a single pseudocubic perovskite structure and undergo a diffuse‐to‐relaxor phase transition owing to the evolution of the domain from a frozen state to a dynamic state. The formation of the above dielectric relaxor behavior was further confirmed by a couple of measurements such as polarization loops, polarization current density curves, as well as bipolar strain loops. A large strain value of ~0.41% at a driving field of 7 kV/mm (normalized strain d₃₃* of ~590 pm/V) was obtained at room temperature for the composition with x = 0.32, which is located near the boundary between ergodic and nonergodic relaxor. Moreover, this electric field‐induced large strain was found to own a frequency‐insensitive characteristic.     

Lead-reduced Bi(Ni2/3Ta1/3)O3-PbTiO3 perovskite ceramics with high Curie temperature and performance

With increasing demand of high-temperature piezoelectric devices and growing concern over environment protection, a feasible reduction in lead from lead-based high Curie temperature piezoelectric materials are desperately needed. Herein, a new system of lead-reduced Bi(Ni_2/3Ta_1/3)O₃-PbTiO₃ (BNT-PT) ferroelectric ceramics is fabricated by a conventional solid-state sintering process. The phase transition behaviors as a function of composition and temperature, electrical properties, as well as the domain configurations from a microscopic level have been investigated in detail. The results indicate that crystal structures, phase transition behaviors, and electric properties of BNT-PT ceramics can be affected significantly by the content of BNT counterpart. Dielectric measurements show that xBNT-(1−x)PT ceramics transfer from the normal ferroelectrics to the relaxor ferroelectrics at compositions of x = 0.3-0.35. The BNT-PT ceramics exhibit high Curie temperature T_C ranging from 474 to 185°C with the variation in BNT content. The relative dielectric tunability n_r also rises from only 0.65% for 0.10BNT-0.90PT to 50.23% for 0.40BNT-0.60PT with increasing BNT content. The tetragonal-rich composition 0.30BNT-0.70PT ceramic possesses the maximum remnant polarization of P_r ~ 34.9 μC/cm². Meanwhile, a highest piezoelectric coefficient of d₃₃ ~ 271 pC/N and a high field piezoelectric strain coefficient of  ~ 560 pm/V are achieved at morphotropic phase boundary (MPB) composition of 0.38BNT-0.62PT. The maximum value of strain ~0.31% is obtained in the 0.36BNT-0.64PT ceramic. The largest electromechanical coupling coefficient k_p is 44.5% for 0.37BNT-0.63PT ceramic. These findings demonstrate that BNT-PT ceramics are a system of high-performance Pb-reduced ferro/piezoelectrics, which will be very promising materials for piezoelectric devices. This study offers an approach to developing and exploring new lead-reduced ferroelectric ceramics with high performances.     

Photoluminescence and Temperature Dependent Electrical Properties of Er‐Doped 0.94Bi0.5Na0.5TiO3‐0.06BaTiO3 Ceramics

Er‐doped 0.94Bi_0.5Na_0.5TiO₃‐0.06BaTiO₃ (BNT‐6BT: xEr, x is the molar ratio of Er³⁺ doping) lead‐free piezoceramics with x = 0–0.02 were prepared and their multifunctional properties have been comprehensively investigated. Our results show that Er‐doping has significant effects on morphology of grain, photoluminescence, dielectric, and ferroelectric properties of the ceramics. At room temperature, the green (550 nm) and red (670 nm) emissions are enhanced by Er‐doping, reaching the strongest emission intensity when x = 0.0075. The complex and composition‐dependent effects of electric poling on photoluminescence also have been measured. As for electrical properties, on the one hand, Er‐doping tends to flatten the dielectric constant‐temperature (ε_r‐T) curves, leading to temperature‐insensitive dielectric constant in a wide temperature range (50°C–300°C). On the other hand, Er‐doping significantly decreases the ferroelectric‐relaxor transition temperature (T_F–R) and depolarization temperature (T_d), with the T_F–R decreasing from 76°C to 42°C for x = 0–0.02. As a result, significant composition‐dependent electrical features were found in ferroelectric and piezoelectric properties at room temperature. In general, piezoelectric and ferroelectric properties tend to become weaker, as confirmed by the composition‐dependent piezoelectric coefficient (d₃₃), planar coupling factor (k_p), and the shape of polarization‐electric field (P–E), current‐electric field (J–E), bipolar/unipolar strain‐electric field (S–E) curves. Furthermore, to understand the relationship between the T_F–R/T_d and the electrical properties, the composition of x = 0.0075 has been intensively studied. Our results indicate that the BNT‐6BT: xEr with appropriate Er‐doping may be a promising multifunctional material with integrated photoluminescence and electrical properties for practical applications.