Processing and characteristics of transparent Gd3TaO7 polycrystalline ceramics

Transparent polycrystalline Gd₃TaO₇ ceramics were successfully developed. A sol‐gel process was used to synthesize Gd₃TaO₇ powder with a uniform composition and an estimated average particle size of 100 nm. Simultaneous thermal gravimetric analysis and differential thermal analysis (TGA/DTA) was used to identify the decomposition sequence as a function of temperature for the as‐synthesized sol‐gel powders. Crystallization was confirmed by X‐ray diffraction (XRD) and a single phase was achieved by calcining at 1000°C. The calcined powders were hot‐pressed at 1400°C to achieve >96% theoretical density with closed pore structure followed by a hot isostatic pressing at 1400°C at 207 MPa to achieve a fully dense structure. Microstructural characterization shows a uniform grain size distribution with an average grain size of about 7 μm. In‐line transmission measurements revealed high transparency in the red and infrared. Thermal conductivity was measured to be >1.6 W/mK at room temperature, decreasing to ~1.3 W/mK by 500°C. Dielectric properties remain stable with relative permittivity values just above 200 and loss tangents <0.005 up to 350°C.     

Fabrication of Gd2O3‐MgO nanocomposite optical ceramics with varied crystallographic modifications of Gd2O3 constituent

The fabrication of Gd₂O₃‐MgO nanocomposite optical ceramics via hot‐pressing using sol‐gel derived cubic‐Gd₂O₃ and MgO nanopowders was investigated. The precursor powder calcined at 600°C had an average particle size of 12 nm. The effects of hot‐pressing temperature on constituent phases, microstructure, mid‐infrared transmittance, and microhardness were studied. The crystallographic modifications of Gd₂O₃ phase varied with the increase in sintering temperature from 1250 to 1350°C. The monoclinic‐Gd₂O₃ phase was retained for the composite sintered at 1350°C and the sample had an average grain size of 90 nm, excellent transmission (80.4%‐84.8%) over 3‐6 μm wavelength range, and enhanced hardness value of 14.1 GPa.     

Synthesis and characterization of nanometric gadolinia powders by room temperature solid-state displacement reaction and low temperature calcination

Nanometric-sized gadolinia (Gd₂O₃) powders were obtained by applying solid-state displacement reaction at room temperature and low temperature calcination. The XRD analysis revealed that the room temperature product was gadolinium hydroxide, Gd(OH)₃. In order to induce crystallization of Gd₂O₃, the subsequent calcination at 600 ∼ 1200 °C of the room temperature reaction products was studied. Calculation of average crystallite size (D) as well as separation of the effect of crystallite size and strain of nanocrystals was performed on the basic of Williamson-Hall plots. The morphologies of powders calcined at different temperatures were followed by scanning electron microscopy. The pure cubic Gd₂O₃ phase was made at 600 °C which converted to monoclinic Gd₂O₃ phase between 1400° and 1600 °C. High-density (96% of theoretical density) ceramic pellet free of any additives was obtained after pressureless sintering at 1600 °C for 4 h in air, using calcined powder at 600 °C.     

Gd2Zr2O7 ceramics synthesized by solid-state reactive sintering: Effects of starting powders with different-scale particle sizes

In this work, the effects of starting oxide powders with different-scale particle sizes on the synthesis of gadolinium zirconate pyrochlore (Gd₂Zr₂O₇, GZO) and its physical properties were studied. Micron Gd₂O₃ (μG), micron ZrO₂ (μZ), nano Gd₂O₃ (nG), and nano ZrO₂ (nZ) powders were used. GZO ceramics were prepared by employing solid-state reactive sintering at 1300 °C, 1400 °C, 1500 °C and 1600 °C with mixed powders of different sizes (μGμZ, μGnZ, nGμZ and nGnZ). X-ray diffraction and Raman analyses of the ceramics revealed that nG has a more significant impact on the crystallization process than nZ. All ceramics synthesized with different sized oxide powders crystallized into pyrochlore phases except for those synthesized with μGnZ mixed powders, which resulted in a fluorite phase. The results indicated that decreasing the particle size of only ZrO₂ to synthesize pyrochlore-phase Gd₂Zr₂O₇ with high crystallinity may not be effective. Samples obtained at 1500 °C were further analyzed. Scanning electron microscopy results revealed that all four ceramics have a non-homogeneous grain size and that the average grain size ranges from 5.40 to 8.30 μm. In addition, the density and Vickers hardness measurements showed that the use of nanopowders significantly improves the mechanical properties.     

Synthesis of Cerium‐Doped Gd3(Al,Ga)5O12 Powder for Ceramic Scintillators with Ultrasonic‐Assisted Chemical Coprecipitation Method

Cerium‐doped Gd₃(Al,Ga)₅O₁₂ powders have been synthesized with ultrasonic‐assisted chemical coprecipitation method (UACC), and the traditional chemical coprecipitation method (CC) was also employed for comparison. The structure and morphology of powders were investigated by XRD, BET, and TEM. The powders were used for preparing ceramics at different temperatures. The specific surface areas of UACC and CC powders calcined at 800°C were 66 and 29 m²/g, respectively. Ceramics derived from UACC and CC powders were sintered at 1600°C, and the densities are 6.67 and 6.48 g/cm³, respectively. UACC is an attractive method for synthesizing GAGG powder for preparing ceramic scintillators.     

Fabrication and laser operation of Yb:Lu2O3 transparent ceramics from co-precipitated nano-powders

In this article, 5 at.% Yb:Lu₂O₃ transparent ceramics were fabricated by vacuum sintering combined with hot isostatic pressing (HIP) posttreatment using co-precipitated nano-powders. The influence of precipitant molar ratio, ammonium hydrogen carbonate, to metal ions (AHC/M³⁺, R value) on the properties of Yb:Lu₂O₃ precursors and calcined powders was investigated systematically. It was found that the powders with different R value calcined at 1100°C for 4 hours were pure cubic Lu₂O₃ but the morphologies of precursors and powders behaved differently. The opaque samples pre-sintered at 1500°C for 2 hours grew into transparent ceramics after HIP posttreatment at 1750°C for 1 hour. The final ceramic with R = 4.8 showed the best optical quality with the in-line transmittance of 79.7% at 1100 nm. The quasi-CW laser operation was performed at 1034 nm and 1080 nm with a maximum output power up to 8.15 W as well as a corresponding slope efficiency of 58.4%.     

Electrolyte materials for solid oxide fuel cells derived from metal complexes: Gadolinia-doped ceria

Gadolinia doped ceria (GDC) powders with different gadolinium contents were successfully prepared by the thermal decomposition of ceria complexes. All the calcined powder samples were found to be ceria-based solid-solutions having a fluorite-type structure. The powders were cold-isostatically pressed and sintered in air at 1500 °C for 5 h to attain a sintered density of about 90% of its theoretical value. The electrical conductivity of the GDC pellets in air was studied as a function of temperature in the 225–700 °C range, by using two-probe electrochemical impedance spectroscopy measurements. The highest total conductivity (σ_600 °C = 0.025 S/cm) was found for the Ce_0.85Gd_0.15O_1.925 composition.     

Effect of calcination temperature on the microstructure,composition and properties of nanometer agglomerated 8YSZ powders for plasma spray-physical vapor deposition (PS-PVD) and coatings thereof

Homemade nano-agglomerated powders 8YSZ powders for PS-PVD were prepared by the spray drying, then calcination processes at four different temperatures (500 °C, 700 °C, 900 °C and 1100 °C) were carried out on the spray-dried powders. Checked by laser particle sizer, scanning electron microscope (SEM) and X-ray diffraction (XRD), the physical properties, microstructure and phase constitutions of the calcined powders were investigated. The results show that the size of powders calcined at 500 °C is increased relative to the spray-dried powder, whereas the powders calcined at 700 °C, 900 °C and 1100 °C possess smaller size. The binding force of the primary particles tend to rise with the increase of calcination temperature. When the temperature was up to 900 °C and above, it was found that the sintering neck indicating with strong binding was formed between the primary particles. In parallel, the powders underwent an m-ZrO₂ to t-ZrO₂ transition as the calcination temperature rose. It is also found that the PS-PVD prepared coatings which were obtained by using the above powders undergo a transformation from a feather-like to a dense laminate structure as the calcination temperature rises. It is noteworthy that the coating obtained by the powders calcined at 700 °C have a special three-layer composite structure of near dense surface layer, columnar intermediate layer and dense sub-layer. The composite structural coating has excellent adhesion and thermal shock resistance, with a bonding strength of 81MPa and no major spalling when water quenched 100 cycles at 1100 °C.     

Densification of zirconia doped yttria transparent ceramics using co-precipitated powders

Ho:Y₂O₃ ceramics were prepared using co-precipitated powders, with ammonium sulfate as dispersant. Y³⁺ was co-precipitated together with Ho³⁺ and Zr⁴⁺ to produce precursors, which were calcined at 1100–1400 °C to produce yttria-based powders. At calcination temperatures of ≤1300 °C, agglomeration of powders was not observed. When the temperature was increased to 1400 °C, severe agglomeration was detected. Densification was closely related to the calcination temperature: a lower calcination temperature resulted in a faster densification of ceramics to the relative density of 99.7%. The ultimate densification to ~100% was also closely related to powders' impurity level and agglomeration. Grain growth was mainly determined by sintering temperature, but not by the initial crystallite size of powders. The optimal calcination temperature was 1300 °C, at which the obtained Ho:Y₂O₃ powder was free from agglomeration. Using this powder, the resultant Ho:Y₂O₃ ceramics showed pore-free microstructure and good optical transparency.     

Synthesis of NdAlO3 with good microwave dielectric properties by stearic acid method

In this study, NdAlO₃ with perovskite structure was synthesized by the stearic acid method at relatively low temperature. The structural characteristics of the as-synthesized product were identified by TG–DSC, XRD, FT–IR, SEM, and TEM techniques. Using the powders as starting materials, NdAlO₃ bulk microwave ceramics were prepared, and the corresponding densification process, microstructural and dielectric properties were studied. The XRD and FI–IR results confirmed that single phase NdAlO₃ could be prepared at low temperature by the stearic acid method. A unique two-dimensional platelike morphology with an unevenly dispersed bubble shape structure was observed in the calcined powder. However, the TEM result revealed that the powder calcined at 800 °C had a good dispersity accompanied with narrow particle size distribution within a range of 20–35 nm. The average particle size of 27.3 nm was in accordance with that calculated from the XRD data. Using the powder calcined at 800 °C as raw materials, the as-obtained NdAlO₃ ceramics sintered at 1500 °C for 4 h possessed the highest density and favorable combined microwave dielectric properties (i.e., ε_r = 23.02, Q × f = 65320 GHz, and τ_f = −32.4 ppm/^°C). The present work developed a fast, energy-efficient approach to synthesize NdAlO₃ powder used as promising raw materials of microwave dielectric ceramics.     

Structure,thermal properties and hot corrosion behaviors of Gd2Hf2O7 as a potential thermal barrier coating material

In this work, Gd₂Hf₂O₇ ceramics were synthesized and investigated as a potential thermal barrier coating (TBC) material. The phase composition, microstructure and associated thermal properties of Gd₂Hf₂O₇ ceramics were characterized systematically. Results show that the thermal conductivity of Gd₂Hf₂O₇ ceramics is 1.40 Wm⁻¹K⁻¹ at 1200 °C, ~25% lower than that of 8 wt% yttria partially stabilized zirconia (8YSZ). Gd₂Hf₂O₇ ceramics also present large thermal expansion coefficients, which decrease from 12.0 × 10⁻⁶ K⁻¹ to 11.3 × 10⁻⁶ K⁻¹ (300–1200 °C). Besides, the hot corrosion behaviors of Gd₂Hf₂O₇ ceramics exposed to V₂O₅ and Na₂SO₄ + V₂O₅ salts at temperatures of 900–1200 °C were discussed in great detail. We pay much attention on the corrosion process, corrosion mechanism and corrosion damage of Gd₂Hf₂O₇ ceramics subjected to molten V₂O₅ and Na₂SO₄ + V₂O₅ salts at different temperatures.     

Preparation and characterization of LnMgAl11O19 (Ln=La,Nd, Gd) ceramic powders

Lanthanide hexaaluminate powders of LaMgAl₁₁O₁₉ (LMA), NdMgAl₁₁O₁₉ (NMA) and GdMgAl₁₁O₁₉ (GMA) were synthesized via the solid state reaction or sol–gel and calcination method. The LMA and NMA powders synthesized by the sol–gel and calcination method at 1600 °C for 8 h exhibit a single hexaaluminate phase with magnetoplumbite structure; however, the GMA powder synthesized by the sol–gel and calcination method at 1600 °C for 8 h contains both a hexaaluminate phase and a small amount of second phase GdAlO₃ with a perovskite structure. The powders synthesized by the solid state reaction method at 1500 °C for 4 h have a small particle size of 1–3 μm, and a large specific surface area and a good uniformity. The powders synthesized by the sol–gel and calcination method at 1600 °C for 8 h have a particle size of 5–20 μm, and exhibit to a certain extent agglomeration.     

Synthesis and characterization of MgAl2O4 spinel precursor sol prepared by inorganic salts

Magnesium aluminate (MgAl₂O₄) spinel precursor sol was prepared using aluminum nitrate and magnesium nitrate as the precursors for alumina and magnesia, respectively. The obtained sol owned a translucent, homogenous, and stable appearance with a density of 1.19 g/cm³, and at the temperatures above 60 °C, converted to a soft and clear gel. The measured pH of sol was in the range of 3–4, and at the calcination temperature of 1000 °C, the solid content of 6% was reached. TGA/DSC analysis was utilized to study the thermal behavior of the sol. Fourier transforms infrared spectroscopy (FTIR) was applied to recognize the existing bounds in the dried and calcined sol. X-ray diffraction patterns revealed the formation of single-phase MgAl₂O₄ up to 600 °C. According to the FESEM images, the grain size for the sol calcined at 1000 °C was estimated at around 50 nm.     

Direct synthesis of PMN samples by spray-drying

The processing and characterisation of Pb(Mg_1/3Nb_2/3)O₃ (PMN) materials, obtained either by spray-drying the solution of the precursors or by the conventional “columbite” method, were investigated and the morphological and micro-structural characteristics were compared. The acid solution of ammonium-peroxo-niobium complex, magnesium and lead nitrates was spray-dried and the precursor powder obtained was calcined at different temperatures ranging from 350 to 900 °C. The morphologies and the XRD patterns of the powders were compared. The calcined powders exhibited a pyrochlore phase above 400 °C converting into an almost pure perovskite phase at 800 °C. The powder calcined at 350, 500 and 800 °C were sintered at different temperatures, ranging from 950 to 1150 °C, always resulting in a pure perovskite PMN material. The XRD patterns of as-fired surfaces of samples sintered at 950 and 1050 °C showed an unwanted PbO phase together with the main PMN, nevertheless this secondary phase is not present in the ground surfaces. The high reactivity of sprayed powder is reflected in the formation and densification of pure perovskite PMN material with a faster process as regards the conventional one; in particular samples of about 96% theoretical density were obtained starting from the amorphous powder calcined at low temperature (350 °C) through a reaction sintering process. Furthermore, due to the better flowability of the spray-dried powder, the cold consolidation process is highly improved and no binder addition to powder is necessary.     

Thermal Properties of (Zr,TM)B2 Solid Solutions with TM = Ta,Mo, Re,V, and Cr

The thermal properties were investigated for hot‐pressed zirconium diboride containing solid solution additions of tantalum, molybdenum, rhenium, vanadium, and chromium. The nominal additions were equivalent to 3 at.% of each metal with respect to zirconium. Using 0.5 wt% carbon as a sintering aid, powders were hot‐pressed to near full density at 2150°C. Rietveld refinement of X‐ray diffraction data was used to measure lattice parameters and to ensure that the additives formed solid solutions. Thermal conductivities were calculated from measured thermal diffusivities and temperature‐dependent values for density and heat capacity. Thermal conductivities at 25°C ranged from 88 W·(m·K)^?1 for nominally pure ZrB₂ down to 28 W·(m·K)^?1 for (Zr,Cr)B₂. Electron contributions to thermal conductivity were calculated from electrical resistivity measurements using the Wiedemann–Franz law. Decreases in phonon and electron conduction correlated with the size of the metallic additive, indicating that changes in atom size in the Zr lattice positions reduced thermal transport.     

Effect of calcination temperature on the fabrication of transparent lutetium titanate by spark plasma sintering

Transparent lutetium titanate (Lu₂Ti₂O₇) bodies were fabricated by spark plasma sintering using Lu₂O₃ and TiO₂ powders calcined from 700 °C to 1200 °C. No solid-state reaction was identified after calcination at 700 °C, whereas single-phase Lu₂Ti₂O₇ powder was prepared at 1100 and 1200 °C. The calcination at 700 °C promoted densification at the early stages of sintering, whereas residual pores at grain boundaries resulted in Lu₂Ti₂O₇ bodies with low transparency. Low-density and opaque Lu₂Ti₂O₇ bodies formed owing to the coarsening of the powder calcined at 1200 °C. The Lu₂Ti₂O₇ body sintered using the powder calcined at the moderate temperature of 1100 °C had a density of 99.5% with the highest transmittances of 41% and 74% at wavelengths of 550 nm and 2000 nm, respectively.     

Effect of calcination temperature on morphology of mesoporous YSZ

A nano-structured mesoporous yttria-stabilized zirconia (YSZ) powders were prepared for the first time using cetyltrimethylammonium bromide (CTAB) as the surfactant and urea as the hydrolyzing agent and using ZrO(NO₃)·6H₂O and Y(NO₃)₃·6H₂O as inorganic precursors. The Brunauer–Emmett–Teller (BET) surface area, Barrett–Joyner–Halender (BJH) pore size distribution and crystallite/particle size of mesoporous YSZ varied with calcine temperatures were studied. Characterizations revealed that the mesoporous YSZ powder calcined at 600 °C was weakly agglomerated and had a high surface area of 137 m²/g with an average grain size of ∼5.8 nm. It was demonstrated that the mesoporous structure remained up to 900 °C. The low-densified YSZ sample with porosity as high as 33% was prepared from mesoporous YSZ powder sintered at 1500 °C for 6 h.     

Synthesis of TiO2–Ag nanocomposite with sol–gel method and investigation of its antibacterial activity against E. coli

TiO₂–Ag nanocomposite was prepared by the sol–gel method and an azeotropic distillation with benzene was used for dehydration of the gel. Because of gel dehydration by distillation method a nanopowder with a surface area of 230 m²/g was produced which decreased to 80 m²/g after calcination. TEM micrographs and XRD patterns showed that spherical nanosized Ag particles (≈ 10 nm) were deposited among TiO₂ particles. The antibacterial activity of calcined powder at 300 and 500 °C was studied in the presence and in the absence of UV irradiation against Escherichia coli as a model for Gram-negative bacteria. The antibacterial tests confirmed the powder calcined at 300 °C possessed more antibacterial activity than the pure TiO₂, amorphous powder and the powder calcined at 500 °C under UV irradiation. In the absence of UV, the reduction in viable cells was observed only with calcinated powder at 300 °C.     

Synthesis,sintering, and grain growth kinetics of Hf6Ta2O17

A systematic study of the solid-state synthesis, pressureless sintering, and grain growth kinetics of Hf₆Ta₂O₁₇ is presented. The ideal conditions for solids-state synthesis of Hf₆Ta₂O₁₇ powder with minimal particle necking was 1250 °C for 2 h in air. The resultant powder has an average particle size of 210 ± 70 nm. The combined synthesis and ball-milling procedure produces highly sinterable Hf₆Ta₂O₁₇ powder, achieving > 97 % of theoretical density after pressureless sintering at 1600 °C for 2 h in air. The grain growth mechanism was sensitive to processing conditions, appearing to be primarily driven by surface diffusion below 1600 °C and grain boundary diffusion above 1650 °C. The respective activation energies for grain growth were found to be Q_S = 659 ± 79 kJ mol⁻¹ and Q_GB = 478 ± 63 kJ mol⁻¹.     

Porous zirconium titanate ceramics synthesized by sol–gel process

Zirconium titanate, ZrTiO₄, was synthesized by sol–gel method from zirconium butoxide and titanium isopropoxide. Amorphous ZrTiO₄ powder was ground, calcined at 500 °C, and milled to homogenize size distribution of the powder. Milled powder was pressed into tablets and sintered at 900–1400 °C for 8 h. Differential scanning calorimetry and dilatometric studies indicated crystallization of ZrTiO₄ at 600–700 °C. Raman spectroscopy and X-ray diffraction analysis confirmed presence of crystallized ZrTiO₄ already at 900 °C, and crystallite size was determined by Scherrer equation. Scanning electron microscopy showed that ZrTiO₄ grains begin to sinter at higher temperatures, starting from 1200 °C, while preserving high porosity up to 1300 °C as confirmed by dilatometry and mercury intrusion porosimetry.