Dielectric Relaxor Evolution and Frequency‐Insensitive Giant Strains in (Bi0.5Na0.5)TiO3‐Modified Bi(Mg0.5Ti0.5)O3–PbTiO3 Ferroelectric Ceramics

The 0.45Bi(Mg_0.5Ti_0.5)O₃–(0.55 ? x)PbTiO₃–x(Bi_0.5Na_0.5)TiO₃ (BMT–PT–xBNT) ternary solid solution ceramics were prepared via a conventional solid‐state reaction method; the evolution of dielectric relaxor behavior and the electrostrain features were investigated. The XRD and dielectric measurements showed that all studied compositions own a single pseudocubic perovskite structure and undergo a diffuse‐to‐relaxor phase transition owing to the evolution of the domain from a frozen state to a dynamic state. The formation of the above dielectric relaxor behavior was further confirmed by a couple of measurements such as polarization loops, polarization current density curves, as well as bipolar strain loops. A large strain value of ~0.41% at a driving field of 7 kV/mm (normalized strain d₃₃* of ~590 pm/V) was obtained at room temperature for the composition with x = 0.32, which is located near the boundary between ergodic and nonergodic relaxor. Moreover, this electric field‐induced large strain was found to own a frequency‐insensitive characteristic.     

Large Strain Response and Fatigue‐Resistant Behavior in Ternary Bi0.5Na0.5TiO3–BaTiO3–Bi(Zn0.5Ti0.5)O3 Solid Solutions

A ternary solid solution (1 ? x)(0.88Bi_0.5Na_0.5TiO₃–0.12BaTiO₃)‐xBi(Zn_0.5Ti_0.5)O₃ (BNBZT, BNBZTx) was designed and fabricated using the traditional solid‐state reaction method. The temperature and composition dependence of dielectric, ferroelectric, piezoelectric, and fatigue properties were systematically investigated and a schematic phase diagram was proposed. The substitution with Bi(Zn_0.5Ti_0.5)O₃ was found to shift the phase transition (ferroelectric tetragonal to relaxor pseudocubic phase) to lower temperatures. At a critical composition x of 0.05, large electric‐field‐induced strain response with normalized strain S_max/E_max as high as 526 pm/V was obtained under a moderate field of 4 kV/mm around room temperature. The strain exhibited good temperature stability within the temperature range of 25°C–120°C. In addition, excellent fatigue‐resistant behavior was observed in the proposed BNBZT solid solution after 10⁶ bipolar cycles. These give the BNBZT system great potential as environmental friendly solid‐state actuator.     

Modulation of electrostriction and strain response in bismuth sodium titanate‐based ceramics

The electrostriction and strain response of lead‐free Bi_0.5Na_0.5TiO₃–BaTiO₃ piezoceramics with La and Nb [(Bi_0.47Na_0.47Ba_0.06)_1?xLa_xTi_1?yNb_yO₃] were modified by optimizing the depolarization temperature. The influences of La and Nb on their phase structure and electrical properties were systematically investigated. All the ceramics exhibited a pseudocubic phase, which is independent of the addition of La and Nb. The strain values increased gradually with the addition of La, and a high strain of ~0.5% (80 kV/cm) was attained without any remnant strain when the compositions had a value of x = 0.015. Instead, the piezoelectric constant d₃₃ dropped down ~20 pC/N due to the shift of the T_d (or T_f?r) to room temperature. Interestingly, by establishing the relationship between T_d and strain values, it should be feasible to optimize the strain property of Bi_0.5Na_0.5TiO₃ (BNT)‐based ceramics by regulating T_d to ambient temperature. In addition, a very high electrostriction coefficient Q₃₃ of ~0.0758 m⁴ C^?2 can be found under high temperatures of 125 and 150°C. We believe that the strain and electrostriction behavior of BNT‐based ceramics can be well modified by the modulation of depolarization temperature.     

Temperature‐insensitive strain behavior in 0.99[(1−x)Bi0.5(Na0.80K0.20)0.5TiO3−xBiFeO3]–0.01Ta lead‐free piezoelectric ceramics

Lead‐free 0.99[(1?x)Bi_0.5(Na_0.80K_0.20)_0.5TiO₃?xBiFeO₃]–0.01Ta (BNKT20–100xBF–1Ta) lead‐free piezoelectric ceramics were fabricated through conventional solid state sintering method. Results showed that change of BF content in the BNKT20–100xBF–1Ta induced a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order. A large electric‐field‐induced strain of 0.36% (at 80 kV/cm driving field, corresponding to a large signal of ~450 pm/V) which is derived from a reversible field‐induced ergodic relaxor to ferroelectric phase transformation, was obtained in the composition with x=0.01 near the ferroelectric‐ergodic relaxor phase boundary. Moreover, an attractive property for application in nonlinear actuators demanding enhanced thermal stability was obtained in this material, which showed a temperature‐insensitive strain characteristic in the temperature range from room temperature to 100°C.     

Temperature‐Dependent Phase Transitions in the Lead‐Free Piezoceramics (1 – x – y)(Bi1/2Na1/2)TiO3–xBaTiO3–y(K0.5Na0.5)NbO3 Observed by in situ Transmission Electron Microscopy and Dielectric Measurements

Lead‐free piezoelectric (1 – x – y)(Bi_1/2Na_1/2)TiO₃–xBaTiO₃–y(K_0.5Na_0.5)NbO₃ (BNT–BT–KNN) ceramics were examined in situ under increasing temperature in the transmission electron microscope. Changing superstructure reflections indicate a transition from rhombohedral to tetragonal to cubic phase with broad coexistence regions. The additional evolution of the microstructure in combination with dielectric measurements leads to a model of two relaxor‐type phase evolutions with temperature.     

Effect of BiMeO3 on the Phase Structure,Ferroelectric Stability,and Properties of Lead‐Free Bi0.5(Na0.80K0.20)0.5TiO3 Ceramics

The effects of BiMeO₃ (Me = Fe, Sc, Mn, Al) addition on the phase transition and electrical properties of Bi_0.5(Na_0.80K_0.20)_0.5TiO₃ (BNKT20) lead‐free piezoceramics were systematically investigated. Results showed that addition of BiFeO₃ into BNKT20 induces a phase transition from tetragonal–rhombohedral coexisted phases to a tetragonal phase with the observation of enhanced piezoelectric properties (d₃₃ = 150 pC/N for 0.02BiFeO₃). BiScO₃, BiMnO₃, and BiAlO₃ substitutions into BNKT20 induce a phase transition from coexistence of ferroelectric tetragonal and rhombohedral to a relaxor pseudocubic with a significant disruption of the long‐range ferroelectric order, and correspondingly adjusts the ferroelectric–relaxor transition point T_F–R to room temperature. Accordingly, large accompanying normalized strains of 0.34%–0.36% are obtained near the ferroelectric–relaxor phase boundary, and the mergence of large strain response can be ascribed to a reversible field‐induced ergodic relaxor‐to‐ferroelectric phase transformation. Moreover, our study also revealed that the composition located at the ferroelectric–relaxor phase boundary where the strain response is consistently derivable shifts to a BNKT20‐rich composition as the tolerance factor t of the end‐member BiMeO₃ increases, and this relationship is expected to provide a guideline for designing high‐performance (Bi_0.5Na_0.5)TiO₃‐based materials by searching the ferroelectric–relaxor phase boundary.     

Electric‐field induced phase transition and fatigue behaviors of (Bi0.5+x/2Na0.5‐x/2)0.94Ba0.06Ti1‐xFexO3 ferroelectrics

The dielectric, piezoelectric properties, and fatigue behaviors of stoichiometric (Bi_0.5+x/2Na_0.5‐x/2)_0.94Ba_0.06Ti_1‐xFe_xO₃ (BNBT‐xFe) ferroelectrics are investigated. Fe substitution leads to the downward shift of the ferroelectric‐relaxor transition temperature (T_F‐R) and increase in strain. Meanwhile, fatigue behaviors of the modified ceramics are significantly enhanced. Ex situ X‐ray diffraction and transmission electron microscopy reveal microscopic mechanism for polarization fatigue on different compositions. The fatigue‐free behavior of ferroelectric BNBT‐0.03Fe is not only attributed to a mechanism involving the formation of defect dipoles, which reduces the pinning effect of migratory oxygen vacancies on domain walls, but is also connected to the decrease in easily suppressed field‐induced ferroelectric tetragonal phase. While for ergodic relaxor BNBT‐0.09Fe, the absence of domain wall contributes to the good fatigue resistance behavior. Interestingly, electric cycling results in an increased fraction of relaxor phase, accompanying by the increase in the total strain and decrease in remnant polarizations.     

Phase Diagrams and Electromechanical Strains in Lead‐Free BNT‐Based Ternary Perovskite Compounds

Lead‐free compounds based on perovskite solid solutions in the ternary system (Bi_0.5Na_0.5)TiO₃‐MeNbO₃‐SrTiO₃ (BNT‐MeNbO₃‐ST, Me=K, Na,(K_0.5Na_0.5)) were fabricated using a conventional solid‐state reaction method. The effect of ST addition to BNT‐MeNbO₃ ceramics on the strain behavior, dielectric, ferroelectric, pyroelectric, and piezoelectric properties was systematically investigated to search the lead‐free piezoelectric materials with an excellent actuating performance. The phase diagrams based on the phase transition temperatures were obtained and the relationship between the phase structure and the electrical properties of the BNT‐MeNbO₃‐ST system has been clarified. A qualitative correlation between the morphotropic phase boundary (MPB)composition and tolerance factor t in BNT‐based systems has also been established and the present work indicates that the t value corresponding to the formation of MPB located in a quite narrow range and provides a guideline to predict the approximate MPB region quickly for new solid solutions. The Raman‐spectra analysis, macroscopic properties, and temperature‐dependent relationships of both polarization and strain demonstrated that the large strain response for this investigated system originates from a field‐induced relaxor to ferroelectric phase transformation.     

Dielectric and Piezoelectric Properties of (1−x)K0.5Bi0.5TiO3–xBa(Ti0.8Zr0.2)O3 Ceramics

The properties of relaxor ceramics in the compositional series (1?x)K_0.5Bi_0.5TiO₃–xBa(Ti_0.8Zr_0.2)O₃ have been investigated. Values of T_m, the temperature of maximum relative permittivity, decreased from 380°C at x = 0.0 to below room temperature for x > 0.7. Compositions x = 0.1 and 0.2 were piezoelectric and ferroelectric. The maximum value of d₃₃ piezoelectric charge coefficient, 130 pC/N, and strain, 0.14%, occurred at x = 0.1. Piezoelectric properties of x = 0.1 were retained after thermal cycling from room temperature to 220°C, consistent with results from high‐temperature X‐ray diffraction indicating a transition to single‐phase cubic at ~300°C.     

Composition‐ and Temperature‐Dependent Large Strain in (1−x)(0.8Bi0.5Na0.5TiO3–0.2Bi0.5K0.5TiO3)– xNaNbO3 Ceramics

Ternary solid solutions of (1 ? x)(0.8Bi_0.5Na_0.5TiO₃–0.2Bi_0.5K_0.5TiO₃)– xNaNbO₃ (BNKT–xNN) lead‐free piezoceramics were fabricated using a conventional solid‐state reaction method. Pure BNKT composition exhibited an electric‐field‐induced irreversible structural transition from pseudocubic to ferroelectric rhombohedral phase at room temperature. Accompanied with the ferroelectric‐to‐relaxor temperature T_F‐R shifted down below room temperature as the substitution of NN, a compositionally induced nonergodic‐to‐ergodic relaxor transition was presented, which featured the pinched‐shape polarization and sprout‐shape strain hysteresis loops. A strain value of ~0.445% (under a driving field of 55 kV/cm) with large normalized strain of ~810 pm/V was obtained for the composition of BNKT–0.04NN, and the large strain was attributed to the reversible electric‐field‐induced transition between ergodic relaxor and ferroelectric phase.     

Preparation and Electric Properties of Bi0.5Na0.5TiO3–Bi(Mg0.5Ti0.5)O3 Lead‐Free Piezoceramics

Lead‐free BNT‐based piezoceramics, (1?x)Bi_0.5Na_0.5TiO₃–xBi(Mg_0.5Ti_0.5)O₃ [(1?x)BNT–xBMT] (0.00 ≤ x ≤ 0.06) binary system, were synthesized using a conventional ceramic fabrication method. Effect of Bi(Mg_0.5Ti_0.5)O₃ (BMT) substitution on room temperature (RT) crystal structure, and temperature dependence of electric properties were investigated. The XRD indicates that a pure perovskite phase is formed. The introduction of BMT decreases E_C of BNT from 7.3 to 4.0 kV/mm, and increases d₃₃ from 58 pC/N to 110 pC/N for the x = 0.05. The system shows a typical ferroelectric (FE) polarization loop P(E) and butterfly bipolar strain‐electric S(E) curve at RT. For the composition of 0.95BNT–0.05BMT antiferroelectric (AFE) phase appears near 80°C, characterized by a constricted P(E) loop and altered bipolar S(E) butterfly, and gradually prevails with increasing temperature. Temperature dependence of dielectric constant shows that T_C increases from 310°C for pure BNT to 352°C for the x = 0.05. The results indicate that the piezoelectric properties of BNT have been improved by means of Bi(Mg_0.5Ti_0.5)O₃ substitution.     

Electrostatic energy storage performances of La(Ni2/3Ta1/3)O3-modified Na0.5Bi0.5TiO3 lead-free ceramics

Ceramic capacitors with high electrostatic energy storage performances have captured much research interest in latest years. Sodium bismuth titanate (Na_0.5Bi_0.5TiO₃)-based ferroelectric ceramics show great potential due to their environment-friendly composition, high polarization, and excellent relaxor properties. However, the nonergodic relaxor state of Na_0.5Bi_0.5TiO₃-based ceramics hampers the decrement of remanent polarization, leading to poor energy storage performance. Herein, the (1 − x)Na_0.5Bi_0.5TiO₃–xLa(Ni_2/3Ta_1/3)O₃ ceramics were designed to generate the transformation between nonergodic and ergodic relaxor state. As a result, the ceramics exhibit improved dielectric relaxation, slim polarization–electric field loops, and flattened current–electric field curves due to highly dynamic polar nanoregions. Particularly, the 0.85Na_0.5Bi_0.5TiO₃–0.15La(Ni_2/3Ta_1/3)O₃ ceramics show large breakdown electric field E_b (345 kV/cm), high recoverable energy density W_rec (3.6 J/cm³), and efficiency η (80.6%), revealing potential applications in electrostatic energy storage.     

Effects of BiMO3 on dielectric,ferroelectric, and piezoelectric properties of perovskite lead‐free piezoelectric BaTiO3–(Bi0.5Na0.5)TiO3 ceramics

New lead‐free piezoelectric ceramics of 0.9BaTiO₃–(0.1?x)(Bi_0.5Na_0.5)TiO₃–xBiMO₃, M=Al and Ga, where x=0.00‐0.10, were fabricated by the solid‐state reaction technique. The effect of BiMO₃ contents on the perovskite structure, phase transition, and dielectric, ferroelectric, and piezoelectric properties was investigated. X‐ray diffraction patterns showed that the ceramics exhibit a monophasic perovskite phase up to x=0.06, suggesting stabilized perovskite structures with B‐site aliovalent substitutions. Compositional‐dependent phase transitions were observed from tetragonal to pseudo‐cubic phase with increasing BiMO₃ amounts. Al³⁺ ions were found to stabilize the transition temperature of the ceramics, while significantly decreasing transition temperature, and a change in the dielectric peak were found with an increasing amount of Ga³⁺. Regarding Al³⁺ substitution, the remanent polarization (P_r) values were found to decrease slightly with the Al³⁺ amount. With regard to Ga³⁺ substitution, P_r values decreased with the Ga³⁺ amount up to 0.06 and then increased slightly. The ceramics became softer with a higher degree of substitution according to the lower coercive field (E_c), when compared with 0.9BaTiO₃–0.1(Bi_0.5Na_0.5)TiO₃ ceramics. Ceramics with a lower degree of substitution and tetragonal phase showed butterfly strain loops that correlated with normal ferroelectric behavior.     

Large Electromechanical Strain in Lead‐Free Binary System K0.5Bi0.5TiO3‐Bi(Mg0.5Ti0.5)O3

Solid solution formation in the lead‐free binary system (1?x)K_0.5Bi_0.5TiO₃?xBi(Mg_0.5Ti_0.5)O₃ has been studied for compositions x ≤ 0.12. X‐ray powder diffraction shows single‐phase perovskite for x < 0.1, and a mixed phase region between tetragonal and pseudocubic phases for compositions 0.04 ≤ x ≤ 0.06. Large electromechanical strains of ~0.3% at fields of 50 kV/cm are recorded in the mixed phase region, with d₃₃* (S_max/E_max) values of ~600 pm/V. The materials sustain polarization at low electric fields with remnant polarization ~18 μC/cm² and coercive field ~20 kV/cm for x = 0.06. Relative permittivity‐temperature plots display relaxor characteristics, with peak temperature ~340°C.     

Effects of Bi0.5Na0.5HfO3 addition on the phase structure and piezoelectric properties of (K,Na)NbO3‐based ceramics

Lead‐free perovskite (1‐x)(K_0.48Na_0.48Li_0.04)Nb_0.95Sb_0.05O₃‐x(Bi_0.5Na_0.5)HfO₃ piezoelectric ceramics were prepared by a traditional ceramic fabrication method. An investigation was conducted to assess the effects of (Bi_0.5Na_0.5)HfO₃ content on the crystal structure, microstructure, phase‐transition temperatures, and piezoelectric properties of the ceramics. The X‐ray diffraction results, combined with the temperature dependence of dielectric properties, revealed that the ceramics experienced a structural transition from an orthorhombic phase to a tetragonal phase with the addition of (Bi_0.5Na_0.5)HfO₃, and a coexistence of orthorhombic and tetragonal phases was identified in the composition range of 0.005≤x≤0.015. An obviously improved piezoelectric activity was obtained for the ceramics with compositions near the orthorhombic‐tetragonal phase boundary, among which the composition x=0.005 exhibited the maximum values of piezoelectric constant d₃₃, and planar and thickness electromechanical coupling coefficients (k_p and k_t) of 246 pC/N, 0.435, and 0.554, respectively. Furthermore, the Curie temperature of the ceramics was found decreasing with the increase in (Bi_0.5Na_0.5)HfO₃ content, but still maintaining above 300°C for the phase boundary compositions. These results indicate that the ceramics are promising lead‐free candidate materials for piezoelectric applications.     

Mn doping effects on electric properties of 0.93(Bi0.5Na0.5)TiO3‐0.07Ba(Ti0.945Zr0.055)O3 ceramics

The validity of Mn element on 0.93(Bi_0.5Na_0.5)TiO₃‐0.07Ba(Ti_0.945Zr_0.055)O₃ ceramics (BNT‐BZT‐xMn) is certified by doping. On account of multiple effects introduced by Mn, the appropriate Mn content facilitates property improvement effectively. Compared with pure BNT‐BZT, d₃₃ of the component x = 0.25 increases about 8% up to 187 pC/N and Q_m of the component x = 1 increases about 84% up to 197. Thermally stimulated depolarization currents (TSDC) measurement reveals Mn additive is helpful to pyroelectric properties as well. The Mn‐doped component x = 0.125 exhibits better pyroelectric performance at room temperature. Corresponding pyroelectric coefficient and the figures of merit reach up to 0.061 μC/(cm² °C), F_i=217 pm/V, F_ν = 0.023 m²/C, and F_d = 12.6 μPa^?1/2, respectively, even superior to lead‐based ceramics. Similar pyroelectric advantage is also observed in the component x = 0.5 near depolarization temperature T_d. Mn doping has slight harmful influence on the ferroelectric‐to‐relaxor transition temperature T_F?R, as well as T_d, but hardly shows restriction on application. These results confirm Mn doping is an available strategy to improve BNT‐based ceramics. Therefore, Mn‐doped BNT‐BZT ceramics will be excellent candidates in area of high‐power piezoelectric application and pyroelectric detectors.     

Stability of High‐Temperature Dielectric Properties for (1 − x)Ba0.8Ca0.2TiO3–xBi(Mg0.5Ti0.5)O3 Ceramics

Ceramics in the solid solution system, (1 ? x)Ba_0.8Ca_0.2TiO₃–xBi(Mg_0.5Ti_0.5)O₃, were prepared by a conventional mixed oxide route. Single‐phase perovskite‐type X‐ray diffraction patterns were observed for compositions x < 0.6. A change from tetragonal to single‐phase cubic X‐ray patterns occurred at x ≥ 0.1. Dielectric measurements indicated relaxor behavior for x ≥ 0.1. Increasing the Bi(Mg_0.5Ti_0.5)O₃ content improved the temperature sensitivity of relative permittivity ?_r at high temperatures. At x = 0.5, a near‐plateau relative permittivity, 835 ± 40, extended across the temperature range, 65°C–550°C; the permittivity increased at x = 0.6 to 2170 ± 100 for temperatures 160°C–400°C (1 kHz). The corresponding loss tangent, tanδ, was ≤0.025 for temperatures between 100°C and 430°C for composition x = 0.5; at x = 0.6, losses increased sharply at >300°C. Comparisons of dielectric properties with other materials proposed for high‐temperature capacitor applications suggest that (1 ? x)Ba_0.8Ca_0.2TiO₃–xBi(Mg_0.5Ti_0.5)O₃ ceramics are a promising base material for further development.     

Giant electromechanical strain response in lead‐free SrTiO3‐doped (Bi0.5Na0.5TiO3–BaTiO3)–LiNbO3 piezoelectric ceramics

Lead‐free 0.985[(0.94?x)Bi_0.5Na_0.5TiO₃–0.06BaTiO₃–xSrTiO₃]–0.015LiNbO₃ [(BNT–BT–xST)–LN, x=0‐0.05] piezoelectric ceramics were prepared using a conventional solid‐state reaction method. It was found that the long‐range ferroelectric order in the unmodified (BNT–BT)–LN ceramic was disrupted and transformed into the ergodic relaxor phase with the ST substitution, which was well demonstrated by the dramatic decrease in remnant polarization (P_r), coercive field (E_c), negative strain (S_neg) and piezoelectric coefficient (d₃₃). However, the degradation of the ferroelectric and piezoelectric properties was accompanied by a significant increase in the usable strain response. The critical composition (BNT–BT–0.03ST)–LN exhibited a maximum unipolar strain of ~0.44% and corresponding normalized strain, S_max/E_max of ~880 pm/V under a moderate field of 50 kV/cm at room temperature. This giant strain was associated with the coexistence of the ferroelectric and ergodic relaxor phases, which should be mainly attributed to the reversible electric‐field‐induced transition between the ergodic relaxor and ferroelectric phases. Furthermore, the large field‐induced strain showed relatively good temperature stability; the S_max/E_max was as high as ~490 pm/V even at 120°C. These findings indicated that the (BNT–BT–xST)–LN system would be a suitable environmental‐friendly candidate for actuator applications.     

Electrical properties and temperature stability of SrTiO3-modified (Bi1/2Na1/2)TiO3-BaTiO3-(K1/2Na1/2)NbO3 piezoceramics

SrTiO₃-modified lead-free piezoelectric ceramics, (0.93-x)Bi_0.5Na_0.5TiO₃-xSrTiO₃-0.06BaTiO₃-0.01 K_0.5Na_0.5NbO₃ [(BNT-xST)-BT-KNN, x = 0-0.06], were prepared using a conventional solid-state reaction method. The XRD structure analysis and electric properties characteristics revealed the ST-induced phase transformation from the ferroelectric phase to the relaxor phase and their coexistence state. Benefiting from the ST-destructed ferroelectric long-range orders, the high normalized strain value of 600 pm/V was obtained in the (BNT-0.02ST)-BT-KNN ceramic at 5 kV/mm. The ST-generated relaxor phase was found to have a constructive effect on improving the temperature stability and restraining the hysteresis of the electric-field-induced strain. The normalized strain of (BNT-0.06ST)-BT-KNN ceramics could be kept at a high value ~337 pm/V at elevated temperature up to 120°C.     

Large Piezoresponse and Ferroelectric Properties of (Bi0.5Na0.5)TiO3–(Bi0.5K0.5)TiO3–Bi(Mg0.5Ti0.5)O3 Thin Films Prepared by Chemical Solution Deposition

Bulk ceramic 72.5 mol%(Bi_0.5Na_0.5)TiO₃–22.5 mol%(Bi_0.5K_0.5)TiO₃–5 mol%Bi(Mg_0.5Ti_0.5)O₃ (BNT–BKT–BMgT) has previously been reported to show a large high‐field piezoelectric coefficient (d₃₃* = 570 pm/V). In this work, the same composition was synthesized in thin film embodiments on platinized silicon substrates via chemical solution deposition. Overdoping of volatile cations in the precursor solutions was necessary to achieve phase‐pure perovskite. An annealing temperature of 700°C resulted in good ferroelectric properties (P_max = 52 μC/cm² and P_r = 12 μC/cm²). Quantitative compositional analysis of films annealed at 650°C and 700°C indicated that near ideal atomic ratios were achieved. Compositional fluctuations observed through the film thickness were in good agreement with the existence of voids formed between successive spin‐cast layers, as observed with electron microscopy. Bipolar and unipolar strain measurements were performed via double laser beam interferometry and a high effective piezoelectric coefficient (d_33,f) of approximately 75 pm/V was obtained.