Structure and electrochemical characterization of LiNi<Subscript>0.3</Subscript>Co<Subscript>0.3</Subscript>Mn<Subscript>0.3</Subscript>Fe<Subscript>0.1</Subscript>O<Subscript>2</Subscript> cathode for lithium secondary battery

A lithium insertion material having the composition LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ was synthesized by simple sol-gel method. The structural and electrochemical properties of the sample were investigated using X-ray diffraction spectroscopy (XRD) and the galvanostatic charge-discharge method. Rietvelt analysis of the XRD patterns shows that this compound can be classified as α-NaFeO₂ structure type (R3m; a=2.8689(5) Å and 14.296(5) Å in hexagonal setting). Rietvelt fitting shows that a relatively large amount of Fe and Ni ion occupy the Li layer (3a site) and a relatively large amount of Li occupies the transition metal layer (3b site). LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ when cycled in the voltage range 4.3–2.8 V gives an initial discharge capacity of 120 mAh/g, and stable cycling performance. LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ in the voltage range 2.8–4.5 V has a discharge capacity of 140 mAh/g, and exhibits a significant loss in capacity during cycling. Ex-situ XRD measurements were performed to study the structure changes of the samples after cycling between 2.8–4.3 V and 2.8–4.5 V for 20 cycles. The XRD and electrochemical results suggested that cation mixing in this layered structure oxide could be causing degradation of the cell capacity.     

The Oxidative Polycondensation of Benzylidene-4′-hydroxyanilene using Air O<Subscript>2</Subscript>, NaOCl and H<Subscript>2</Subscript>O<Subscript>2</Subscript>: Synthesis and Characterization

In this work, the oxidative polycondensation reaction conditions of benzylidene-4′-hydroxyanilene (B-4′-HA) were studied using oxidants such as air O₂, H₂O₂ and NaOCl in an aqueous alkaline medium between 40 and 95 ^○C. Oligo-benzylidene-4′-hydroxyanilene was characterized by ¹H-NMR, FT-IR, UV-Vis, size exclusion chromatography (SEC) and elemental analysis techniques. The solubility of oligomer using organic solvents such as DMF, THF, DMSO, methanol, ethanol, CHCl₃, CCl₄, toluene, acetonitrile, ethyl acetate was investigated. According to air O₂ oxidant (flow rate 8.5 L/h), the conversion of B-4′-HA was 82.0% in optimum conditions such as [B-4′-HA]₀=[KOH]₀=0.1015 mol/L at 50 ^○C for 25 h. According to the SEC analysis, the number-average molecular weight (M_n), weight-average molecular weight (M_w) and polydispersity index (PDI) values of O-B-4′-HA were found to be 1852 g mol⁻¹, 3101 g mol⁻¹ and 1.675; 2123 g mol⁻¹, 4073 g mol⁻¹ and 1.919; 2155 g mol⁻¹, 4164 g mol⁻¹ and 1.932, using air oxygen, NaOCl and H₂O₂ oxidants, respectively. Also, Thermo gravimetric analysis (TGA) showed oligo-benzylidene-4′-hydroxyanilene to be unstable against thermo-oxidative decomposition. The weight loss of O-B-4′-HA was found to be 95.87% at 1000 ^○C.     

Polystyrene-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite solid polymer electrolyte for lithium secondary battery

In a common salt-in-polymer electrolyte, a polymer which has polar groups in the molecular chain is necessary because the polar groups dissolve lithium salt and coordinate cations. Based on the above point of view, polystyrene [PS] that has nonpolar groups is not suitable for the polymer matrix. However, in this PS-based composite polymer-in-salt system, the transport of cations is not by segmental motion but by ion-hopping through a lithium percolation path made of high content lithium salt. Moreover, Al₂O₃ can dissolve salt, instead of polar groups of polymer matrix, by the Lewis acid-base interactions between the surface group of Al₂O₃ and salt. Notably, the maximum enhancement of ionic conductivity is found in acidic Al₂O₃ compared with neutral and basic Al₂O₃ arising from the increase of free ion fraction by dissociation of salt. It was revealed that PS-Al₂O₃ composite solid polymer electrolyte containing 70 wt.% salt and 10 wt.% acidic Al₂O₃ showed the highest ionic conductivity of 9.78 × 10^-5 Scm^-1 at room temperature.     

Synthesis and electrochemical properties of submicron LiNi0.8Co0.2O2 by a polymer-pyrolysis method

A polymer-pyrolysis method was used to synthesize LiNi_0.8Co_0.2O₂, which has potential application in lithium ion batteries. The effect of calcination temperature and time on the structure and electrochemical performance of the material was investigated. XRD analysis showed that the powders obtained by calcination at 750 °C for 3 h had the best-ordered hexagonal layer structure. SEM image showed these powders were fine, narrowly distributed with platelet morphology. The charge-discharge tests demonstrated these powders had the best electrochemical properties, with an initial discharge capacity of 189 mAh/g and capacity retention of 95.2% after 50 cycles when cycled at 50 mA/g between 3.0 and 4.3 V. Besides, these powders also had exhibited excellent rate capability.     

Synthesis of cathode material LiNi<Subscript>1-<Emphasis Type="Italic">y</Emphasis></Subscript>Co<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>O<Subscript>2</Subscript> by a simplified combustion method

The optimum conditions for synthesizing LiNi_1-y Co _y O₂ (y=0.1, 0.3 and 0.5) by a simplified combustion method, in which the preheating step is omitted, and the electrochemical properties of these materials were investigated. The optimum condition for synthesizing LiNi_0.9Co_0.1O₂ by the simplified combustion method is calcination at 800 °C for 12 h in air in 3.6 mole ratio of urea to nitrate. The LiNi_0.9Co_0.1O₂ synthesized under these conditions shows the smallest R-factor{(I ₀₀₆+I ₁₀₂)/I ₁₀₁} and the largest I ₀₀₃/I ₁₀₄, indicating better hexagonal ordering and less cation mixing, respectively. The LiNi_0.7Co_0.3O₂ synthesized at 800 °C for 12 h in air in 3.6 mole ratio of urea to nitrate has the largest first discharge capacity 156.2 mA h g⁻¹ at 0.5C and shows relatively good cycling performance. This sample shows better hexagonal ordering and less cation mixing than the other samples. The particle size of the LiNi_0.7Co_0.3O₂ is relatively small and its particles are spherical with uniform particle size.     

Synthesis and electrochemical properties of layered LiNi<Subscript>1/2</Subscript>Mn<Subscript>1/2</Subscript>O<Subscript>2</Subscript>prepared by coprecipitation

Spherical LiNi_1/2Mn_1/2O ₂ powders were synthesized from LiOH . H₂O and coprecipitated metal hydroxide, (Ni_1/2Mn_1/2)(OH)₂. The average particle size of the powders was about 10 m and the size distribution was quite narrow due to the homogeneity of the metal hydroxide, (Ni_1/2Mn_1/2)(OH)₂. The tap-density of the LiNi_1/2Mn_1/2O₂ powders was approximately 2.2 g cm_–3, which is comparable to the tap-density of commercial LiCoO₂. The LiNi_1/2Mn_1/2 O₂electrode delivered a discharge capacity of 152, 163, 183, and 189 mA h g^–1 in the voltage ranges of 2.8–4.3, 2.8–4.4, 2.8–4.5, and 2.8–4.6 V, respectively, with good cyclability. Furthermore, Al(OH)₃-coated LiNi_1/2Mn_1/2O₂exhibited excellent cycling behavior and rate capability compared to the pristine electrode.     

Maximization of total surface area of Pt-SnO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst by the Taguchi method

The maximization of the total surface area of Pt-SnO₂/Al₂O₃ catalyst was studied by using the Taguchi method of experimental design. The catalysts were prepared by sol-gel method. The effects of HNO₃, H₂O and aluminum nitrate concentrations and the stirring rate on the total surface area were studied at three levels of each. L₉ orthogonal array leading nine experiments was used in the experimental design. The parameter levels that give maximum total surface area were determined and experimentally verified. In the range of conditions studied it was found that, medium levels of HNO₃ and H₂O concentration and lower levels of aluminum nitrate concentration and stirring rate maximize the total surface area.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> xerogel support on hydrogen production by steam reforming of LNG over Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> catalyst

An Al₂O₃-ZrO₂ xerogel (AZ-SG) was prepared by a sol-gel method for use as a support for a nickel catalyst. The Ni/AZ-SG catalyst was then prepared by an impregnation method, and was applied to hydrogen production by steam reforming of LNG. A nickel catalyst supported on commercial alumina (A-C) was also prepared (Ni/A-C) for comparison. The hydroxyl-rich surface of the AZ-SG support increased the dispersion of nickel species on the support during the calcination step. The formation of a surface nickel aluminate-like phase in the Ni/AZ-SG catalyst greatly enhanced the reducibility of the Ni/AZ-SG catalyst. The ZrO₂ in the AZ-SG support increased the adsorption of steam onto the support and the subsequent spillover of steam from the support to the active nickel sites in the Ni/AZ-SG catalyst. Both the high surface area and the well-developed mesoporosity of the Ni/AZ-SG catalyst improved the gasification of adsorbed surface hydrocarbons in the reaction. In the steam reforming of LNG, the Ni/AZ-SG catalyst showed a better catalytic performance than the Ni/A-C catalyst. Moreover, the Ni/AZ-SG catalyst showed strong resistance toward catalyst deactivation.     

Self-Metathesis of 1-Octene Using Alumina-Supported Re<Subscript>2</Subscript>O<Subscript>7</Subscript> in Supercritical CO<Subscript>2</Subscript>

In this contribution we describe the use of heterogeneous catalysts for the liquid-phase self-metathesis of 1-octene in supercritical CO₂. Our work aims at addressing the mass-transfer problems associated with such reaction systems. By coupling a heterogeneous supported Re₂O₇ catalyst with the use of scCO₂, the self-metathesis of 1-octene takes place by and large much more rapidly than in traditional solvent media, and furthermore, by using scCO₂ the overall efficiency and sustainability of the transformation can be improved.

Trapping characteristics of volatile ruthenium oxides by Y<Subscript>2</Subscript>O<Subscript>3</Subscript> filter

Yttria filter has been suggested as a trapping agent for gaseous oxides of ruthenium volatilized during DUPIC fuel fabrication process. Experiments were performed to evaluate the trapping characteristics of gaseous ruthenium oxides by yttria ceramic foam filters in the two-zone furnace under air condition. Yttria filter is expected to offer stable material in which the volatility of the ruthenium can be effectively trapped because of its incorporation into a lattice of high stability over 900 ‡C under air condition. The XRF result of ruthenium trapped on an yttria filter under air condition showed that concentrations of ruthenium on the back and the front faces of the filter decreased linearly with increasing superficial air velocity, and the back face concentration of filter was lower than the front face concentration by about 30-45%. The TGA result of ruthenium trapped on an yttria filter indicates that there is weight loss of 5.8 wt% up to 1,400 ‡C, which is believed to be due to the fact that the thermally stable Y₂Ru₂O₇ phase was formed on an yttria filter.     

Synergism Between Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Au/TiO<Subscript>2</Subscript> in the Low Temperature Oxidation of Propene

CO impedes the low temperature (<170 °C) oxidation of C₃H₆ on supported Pt. Supported Au catalysts are very effective in the removal of CO by oxidation, although it has little propene oxidation activity under these conditions. Addition of Au/TiO₂ to Pt/Al₂O₃ either as a physical mixture or as a pre-catalyst removes the CO and lowers the light-off temperature (T ₅₀) for C₃H₆ oxidation compared with Pt catalyst alone by ~54 °C in a feed of 1% CO, 400 ppm C₃H₆, 14% O₂, 2% H₂O.     

Comparative study of the preparation and electrochemical performance of LiNi<Subscript>1</Subscript><Subscript>/2</Subscript>Mn<Subscript>1/2</Subscript>O<Subscript>2</Subscript> electrode material for rechargeable lithium batteries

Positive electrode material LiNi_1/2Mn_1/2O₂ was synthesized via the carbonate co-precipitation method and the hydroxide precipitation route to study the effects of the precursor on its structural and electrochemical properties. The results of X-ray diffraction and Rietveld refinement show that the carbonate precursor of Ni²⁺ and Mn²⁺ exhibits one phase at a pH of 8.5, while the hydroxide deposit separates into Ni(OH)₂ and Mn(OH)₂ phases under the same experimental conditions. LiNi_1/2Mn_1/2O₂ material prepared from the hydroxide precursor shows 8.9% Li/Ni exchange and a large capacity loss of 11.3% in the first 10 cycles. By contrast, more uniform distribution of transition metal ions and stable Mn²⁺ in the carbonate precursor contribute to only 7.8% Li/Ni disorder in the obtained LiNi_1/2Mn_1/2O₂, which delivers a reversible capacity of about 182 mAh g⁻¹ at a current rate of 14 mA g⁻¹ between 2.5 and 4.8 V.     

Synthesis of ZnGa<Subscript>2</Subscript>O<Subscript>4</Subscript> Hierarchical Nanostructure by Au Catalysts Induced Thermal Evaporation

In this paper, ZnGa₂O₄ hierarchical nanostructures with comb-like morphology are fabricated by a simple two-step chemical vapor deposition (CVD) method: first, the Ga₂O₃ nanowires were synthesized and employed as templates for the growth of ZnGa₂O₄ nanocombs; then, the as-prepared Ga₂O₃ nanowires were reacted with ZnO vapor to form ZnGa₂O₄ nanocombs. Before the reaction, the Au nanoparticles were deposited on the surfaces of Ga₂O₃ nanowires and used as catalysts to control the teeth growth of ZnGa₂O₄ nanocombs. The as-prepared ZnGa₂O₄ nanocombs were highly crystallized with cubic spinel structure. From the photoluminescence (PL) spectrum, a broad band emission in the visible light region was observed of as-prepared ZnGa₂O₄ nanocombs, which make it promising application as an optical material.     

Structural characterization and electrochemical properties of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> anode materials synthesized by a hydrothermal method

Cobalt oxide [Co₃O₄] anode materials were synthesized by a simple hydrothermal process, and the reaction conditions were optimized to provide good electrochemical properties. The effect of various synthetic reaction and heat treatment conditions on the structure and electrochemical properties of Co₃O₄ powder was also studied. Physical characterizations of Co₃O₄ are investigated by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller [BET] method. The BET surface area decreased with values at 131.8 m²/g, 76.1 m²/g, and 55.2 m²/g with the increasing calcination temperature at 200°C, 300°C, and 400°C, respectively. The Co₃O₄ particle calcinated at 200°C for 3 h has a higher surface area and uniform particle size distribution which may result in better sites to accommodate Li⁺ and electrical contact and to give a good electrochemical property. The cell composed of Super P as a carbon conductor shows better electrochemical properties than that composed of acetylene black. Among the samples prepared under different reaction conditions, Co₃O₄ prepared at 200°C for 10 h showed a better cycling performance than the other samples. It gave an initial discharge capacity of 1,330 mAh/g, decreased to 779 mAh/g after 10 cycles, and then showed a steady discharge capacity of 606 mAh/g after 60 cycles.     

Selective oxidation of H<Subscript>2</Subscript>S to ammonium thiosulfate and elemental sulfur using mixtures of V-Bi-O and Sb<Subscript>2</Subscript>O<Subscript>4</Subscript>

The selective oxidation of hydrogen sulfide in the presence of excess water and ammonia was investigated by using vanadium-bismuth based mixed oxide catalysts. Synergistic effect on catalytic activity was observed for the mechanical mixtures of V-Bi-O and Sb₂O₄. Temperature programmed oxidation (TPO), X-ray photoelectron spectroscopy (XPS), and two separated bed reactivity test results supported the role of Sb₂O₄ for reoxidizing the reduced V-Bi-O during the reaction. This paper is dedicated to Professor Hyun-Ku Rhee on the occasion of his retirement from Seoul National University.     

Side-by-Side In(OH)<Subscript>3</Subscript> and In<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanotubes: Synthesis and Optical Properties

A simple and mild wet-chemical approach was developed for the synthesis of one-dimensional (1D) In(OH)₃ nanostructures. By calcining the 1D In(OH)₃ nanocrystals in air at 250 °C, 1D In₂O₃ nanocrystals with the same morphology were obtained. TEM results show that both 1D In(OH)₃ and 1D In₂O₃ are composed of uniform nanotube bundles. SAED and XRD patterns indicate that 1D In(OH)₃ and 1D In₂O₃ nanostructures are single crystalline and possess the same bcc crystalline structure as the bulk In(OH)₃ and In₂O₃, respectively. TGA/DTA analyses of the precursor In(OH)₃ and the final product In₂O₃ confirm the existence of CTAB molecules, and its content is about 6%. The optical absorption band edge of 1D In₂O₃ exhibits an evident blueshift with respect to that of the commercial In₂O₃ powders, which is caused by the increasing energy gap resulted from decreasing the grain size. A relatively strong and broad purple-blue emission band centered at 440 nm was observed in the room temperature PL spectrum of 1D In₂O₃ nanotube bundles, which was mainly attributed to the existence of the oxygen vacancies.     

Electrochemical characterization of zirconium-doped LiNi0.8Co0.2O2 cathode materials and investigations on deterioration mechanism

The electrochemical performance and the degradation mode of the zirconium doped cathode material, LiNi_0.8Co_0.18Zr_0.02O₂ were investigated and compared with the pristine cathode, LiNi_0.8Co_0.2O₂. The cyclic performance of the doped cathode was superior to the pristine cathode, especially under the high voltage cutoff, although its rate capability remained unimproved. The trend in the graphs of the differential capacity showed that the impedance growth of the cell made of the pristine cathode was much faster than the doped. From the results of the XRD pattern changes between before and after the galvanostatic cycling, less cation mixing and more ordered hexagonal structure were observed for the doped cathode. The impedance spectra showed that the charge transfer resistance for the pristine cathode grew significantly with cycling, while that for the doped cathode increased just moderately. Considerable decrease in the impedance was observed when the new lithium was substituted with the cycled anode, which implied that the interfacial impedance growth on the anode accounted for about 20% of the total impedance measured. It is concluded that the fading mode for LiNi_0.8Co_0.2O₂ is mainly due to the cation mixing, partially contributed by the impedance growth on the anode and by doping the pristine cathode with Zr, cation mixing can be efficiently suppressed.     

Synthesis and Cytotoxicity of Y<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanoparticles of Various Morphologies

As the field of nanotechnology continues to grow, evaluating the cytotoxicity of nanoparticles is important in furthering their application within biomedicine. Here, we report the synthesis, characterization, and cytotoxicity of nanoparticles of different morphologies of yttrium oxide, a promising material for biological imaging applications. Nanoparticles of spherical, rod-like, and platelet morphologies were synthesized via solvothermal and hydrothermal methods and characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), light scattering, surface area analysis, thermogravimetric analysis (TGA), and zeta potential measurements. Nanoparticles were then tested for cytotoxicity with human foreskin fibroblast (HFF) cells, with the goal of elucidating nanoparticle characteristics that influence cytotoxicity. Cellular response was different for the different morphologies, with spherical particles exhibiting no cytotoxicity to HFF cells, rod-like particles increasing cell proliferation, and platelet particles markedly cytotoxic. However, due to differences in the nanoparticle chemistry as determined through the characterization techniques, it is difficult to attribute the cytotoxicity responses to the particle morphology. Rather, the cytotoxicity of the platelet sample appears due to the stabilizing ligand, oleylamine, which was present at higher levels in this sample. This study demonstrates the importance of nanoparticle chemistry on in vitro cytotoxicity, and highlights the general importance of thorough nanoparticle characterization as a prerequisite to understanding nanoparticle cytotoxicity.     

Rhodium stabilized Prussian Blue-modified graphite electrodes for H<Subscript>2</Subscript>O<Subscript>2</Subscript> amperometric detection

Graphite electrodes chemically modified with Prussian Blue (G/PB) were obtained by spreading, on the electrode surface, appropriate volumes of 100 mM K₃[Fe(CN)₆] and 100 mM FeCl₃ solutions, both containing 10 mM HCl. In order to improve the electrochemical response stability, the potential of G/PB electrodes was cycled (in the domain where PB exhibits electrochemical activity) in 0.1 M KCl solution (G/PB-K), as well as in 2 mM RhCl₃ solution, containing 0.05 M KCl (G/PB-Rh). Compared with G/PB-K, the G/PB-Rh modified electrodes showed: (i) higher relative stability of the PB electrochemical response; (ii) better analytical parameters for H₂O₂ amperometric detection; (iii) slightly lower rate constant corresponding to the second order electrocatalytic reaction for H₂O₂ amperometric detection; (iv) an electrocatalytic activity not affected by the H₂O₂ concentration.     

Partial oxidation of methane over Ni/Ce-Zro<Subscript>2</Subscript>/θ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The catalytic behavior of Ni/Ce-ZrO₂/θ-Al₂O₃ has been investigated in the partial oxidation of methane (POM) toward synthesis gas. The catalyst showed high activity and selectivity due to the heat treatment of the support and the promotional effect of Ce-ZrO₂. It is suggested that the support was stabilized through the heat treatment of γ-Al₂O₃ and the precoating of Ce-ZrO₂, on which a protective layer was formed. Moreover, sintering of the catalyst was greatly suppressed for 24 h test. Pulse experiments of CH₄, O₂ and/or CH₄/O₂ with a molar ratio of 2 were systematically performed over fresh, partially reduced and well reduced catalyst. Results indicate that CH₄ can be partially oxidized to CO and H₂ by the reactive oxygen in complex NiO_x species existing over the fresh catalyst. It is demonstrated that POM over Ni/Ce-ZrO₂/θ-Al₂O₃ follows the pyrolysis mechanism, and both the carbonaceous materials from CH₄ decomposition over metallic nickel and the reactive oxygen species present on NiO_x and Ce-ZrO₂ are intermediates for POM.