小张角环加载波纹喇叭中表面波的传播及辐射特性

本文利用空间谐波法导出了小张角环加载波纹圆锥喇叭中表面的传播文程，利用数值方法求解该方程，并分析了表面波在喇叭内的传播及辐射特性。数值计算结果与实测值吻合一致。结果表明，喇叭内激励的表面波主要影响喇叭的Ｅ面辐射场和交叉极化辐射场。     

a broad-band constant beamwidth corrugated rectangular horn

Using aperture field theory to predict the far-field radiation from a rectangular horn, a horn with substantially constantE- andH-plane beamwidths of17degand10degrespectively, is designed to operate over a 2.4:1 bandwidth. Assuming a cosine aperture field distribution in both theE- andH-planes of the horn, the general conclusion is first made that an aperture phase error of 0.37 wavelengths at the lowest operating frequency produces the least beamwidth variation (3 dB) over the band. A general design curve showing "constant" beamwidth as a function of horn throat length is produced, furthering the design of such horns with beamwidths in the range approximately9degto27deg. TheE-plane walls of the horn are corrugated, and to cover the bandwidth corrugations are comprised of "T-section" slots which are designed from a simple transmission line model. To realize the specified beamwidths, a compound horn configuration is adopted. Some experimental results obtained from a prototype horn are given.     

Design of corrugated horns: a primer

Typical example of horn is shown where the inside wall is manufactured in a succession of slots and "teeth". The purpose of the corrugated surface is to provide the means to support the propagation of hybrid modes within the horn. Hybrid modes are basically a combination of TE and TM modes. Some basic information for the inexperienced horn designer to get started in designing their corrugated horn is provided. The class of circularly symmetrical corrugated horns and the parameters in designing are considered. As an example a standard Ku-band operation from a typical Earth station is also considered.     

Analysis of soft and hard strip-loaded horns using a circularcylindrical model

Strip-loaded horns with transverse (soft) and longitudinal (hard) strips are analyzed theoretically. The method is based on a circular cylindrical and uniform waveguide model with a periodic strip structure. The field is represented by an infinite series of space harmonics (Floquet modes) in the air-filled central region and in the dielectrically filled wall region. The tangential field is forced to be continuous across the air-dielectric boundary. The propagation constant and the total field (including the hybrid factor) can be determined by solving the resulting matrix equations. The convergence of the solution has been accelerated by calculating the higher-order terms analytically. It is shown that the soft-strip-loaded horn in principle exhibits the same electrical behavior as a corrugated horn. The horn represents an interesting alternative to the corrugated horn in wide-band or dual-band applications, in particular for millimeter waves and for lightweight applications onboard satellites. The hard-strip-loaded horn has potentially high gain and low cross polarization over a certain frequency range, dependent on the horn dimensions, thickness of the dielectric wall and on how strongly the stripline modes are being excited     

Investigation of a 90° corrugated horn

Wide-angle corrugated horns have found important practical applications as feeds for front-fed reflector antennas when low levels of crosspolarisation are required. A theoretical study has been carried out on the 90° corrugated horn for a structure possessing an 'arbitrary, but finite, number of corrugations. Computed and measured results are shown to be in good agreement for a horn possessing three annular slots.     

A dielectric hybrid mode antenna feed: A simple alternative to the corrugated horn

A hybrid-mode horn antenna has been analyzed theoretically and experimentally. It consists of a conical metal horn with a dielectric core inside, separated from the metal wall by another dielectric layer with lower permittivity than for the core material. It is characterized by a very simple design and excellent electrical performance. The horn can support the balanced hybrid HE11-mode, and exhibits low cross polarization and low sidelobes over a wide frequency range. Compared to corrugated horns, the new horn has a simpler design, is easier to analyze, and has the potential of similar cross-polar bandwidth as for corrugated horns with ring-loaded corrugations. Drawbacks are the effects of dielectric losses. Thus the new horn represents an attractive alternative to the corrugated horn antenna.     

Hybrid modes in corrugated conical horns

A simpler solution for spherical hybrid modes in corrugated conical horns has been shown to have a deviation from the rigorous solution of less than 0.7 dB for the case considered by Clarricoats. Expressions for the radiation pattern and gain of such a horn with small flare angle have been obtained under balanced hybrid conditions.     

GTD analysis of the radiation patterns of conical horns

The far-field radiation patterns of conical horns of arbitrary flare angles excited in theTE_{11}mode are obtained employing the geometric theory of diffraction (GTD) based on the theory of Kouyoumjian and Pathak [3] and the slope diffraction technique [4]. The analysis presented enables one to predict accurately radiation patterns over the main beam, near and far sidelobes, and the becklobe of the horn. Validity of the analysis is established by satisfactory agreement between the calculated and measured patterns of an experimental conical horn. The radiation patterns of wide-flare corrugated conical horns excited in theHE_{11}mode of operation have also been calculated over the main beam, which contains most of the radiated energy (up to -40 dB with respect to boresight field), employing slope diffraction technique, and a good agreement is noticed between the calculated and measured radiation patterns.     

Characterization of corrugated feed horns at 216 and 300 GHz

We present measurements of the near-field beam profiles of two corrugated feed horns with center frequencies of 216 and 300 GHz. Both co-polar and cross-polar components of the electric field have been probed across the operation band of the horns. A full-wave numerical near-field transformation, based on a vector Kirchhoff integral, is implemented to transform the measured field to the horn aperture for a comparison with the ideal aperture field. From the overlap integral of the transformed and the ideal field, we conclude that the field radiated by these horns is the HE₁₁ mode, to a purity of better than 99%.     

Compact multimode horn with low sidelobes for global Earth coverage

A new multimode corrugated horn is described for full-Earth coverage from a geostationary satellite. The horn has low sidelobes, low cross polarization, and is compact. We outline the design of this horn and compare its performance with other circular horn types, including conventional single and multimode-corrugated horns and dielectric loaded horns. A design was fabricated and measured results are described for return loss, radiation patterns, and axial ratio. These measurements demonstrate excellent agreement with computer predictions using mode-matching software     

High-Q resonances due to surface waves and their effects on theperformances of corrugated horns

We present a study of high-Q resonance phenomena that occur in corrugated horn structures. It is found that high-Q resonances occur within certain frequency bands where two types of modes, i.e., space-wave and surface-wave modes, simultaneously propagate. A simple model is presented to explain the resonance mechanism. The model yields the conditions for resonance, explains the Q of the resonance, and provides the associated resonant frequency. Approximate formulas for the upper and lower bound frequencies of a resonant band are obtained. It is found that the high-Q resonances deteriorate the gain and crosspolar performances of a horn even if the return losses are acceptable at some resonant frequencies. Rectangular corrugated horns are more susceptible to these resonances than circular corrugated horns, and the reasons for such a difference are explained     

Propagation and radiation behavior of dielectric-loaded pluralhybrid mode multiflare conical horn antennas

A dielectric-loaded multiflare conical horn exhibiting the desirable features of low sidelobes and cross-polarization with the additional advantage of increased on-axis gain is reported. This new horn is developed by combining the techniques of multimode operation for low cross-polarization and sidelobe levels, and dielectric loading for aperture efficiency enhancement. The condition for the support of balanced hybrid modes for low cross polar radiation in the dielectric-loaded multimode horn is derived. Also, the equation for the dielectric thickness for maximum aperture efficiency at a given frequency is obtained. This new type of multimode horn is potentially simple to design, analyze, and manufacture, yet it exhibits the desirable features of a corrugated conical horn and hence can be an attractive alternative to corrugated conical horns for communication applications     

Numerical solution for the near-field transmission between two H-plane sectoral electromagnetic horns

The effect of higher order interactions in the coupling between twoH-plane sectoral electromagnetic horns on the field distribution at the aperture of the transmitting horn is calculated using the point matching technique. A nonsingular integral equation for the induced current in the receiving horn, due to the initially incident wave from the transmitting horn, is formulated using a conformal transformation which maps the cross sectional contour of the receiving horn onto two circles on which the induced currents are finite. The solution leads to a modified field distribution in the transmitting aperture which is then employed in Hu's near-zone power transmission formula to compute a gain correction factor forH-plane sectoral horns. It is shown that the correction factor oscillates about that reported by Chu and Semplak with an amplitude which increases for smaller separation distances.     

Broad-band elliptical beamshape horns with low cross polarization

Horn antennas with an elliptical beam and low cross polarization are discussed. A new class of elliptical-beamshape horns has been investigated. The horns are based on the dielectric core approach, using a dielectric core inside a smooth-walled horn. Horns with rectangular as well as elliptical cross sections have been studied. Experiments show that they have considerably larger cross-polar bandwidth than that obtained from corrugated horns with an elliptical beam. They are also potentially much cheaper to manufacture     

A review of the early developments of circular-aperture hybrid-mode corrugated horns

The simultaneous but independent development in the United States and Australia of circular-aperture corrugated horns in the early 1960's is reviewed. The features of this development include the wide flare-angle corrugated "scalar" horn and the characteristics of focal-region fields of reflector antennas and the single- and multimode cylindrical corrugated horns necessary to feed them.     

The strip-loaded hybrid-mode feed horn

A novel typed of hybrid-mode feed horn is presented. It comprises a hollow conical dielectric waveguide whose outer surface is metallized, and whose inner surface is coated with circumferentially oriented conducting strips. It may be designed to have mimimal cross polarization at two arbitrarily separated frequencies, as for a dual depth corrugated horn. Compared to the corrugated horn, it has the potential of lower weight and lower price. Small horns will have some cross polarization due to undesired radiation from the fields transmitted within the dielectric.     

准太赫兹波段角锥波纹喇叭天线的设计

波纹喇叭天线是20世纪70年代出现的用于微波天线的一种新型器件,它结构紧凑、加工方便、成本较低。不仅如此,它还是一种高效率的馈源,它的方向图具有低旁瓣、轴对称、交叉极化小等一系列优点,因而得到广泛的应用。文中介绍了准太赫兹角锥波纹喇叭天线的基本设计思想。设计了一种工作在140 GHz左右频段的E面波纹角锥喇叭天线。计算机模拟达到了相对于平壁角锥喇叭来说较小波瓣宽度,极低旁瓣电平,E,H面波瓣图趋同的效果。     

Corrugated horns

The corrugated horn has become the preferred choice of antenna for use in high-performance microwave reflector antennas for communications, radar and remote sensing. The principles and attributes of corrugated horns are explained. The analysis, design and manufacturing techniques and types of horns in use are briefly discussed     

An Investigation of Corrugated Groove Conical Horns with Small Flare Angle

Including space harmonics in the interior region of the waveguide, the fields radiated by a \( HE^{{{\left( 1 \right)}}}_{{11}} \) mode in an aperture of a corrugated groove conical horn are described, and theoretical radiation patterns of the horns are given. Experimental results in support of our theory have also been presented.     

An offset reflector antenna with low sidelobes

The corrugated conical horn is considered to be an ideal feed for low sidelobe reflector antennas because of its unique characteristics. Analysis is carried out to show that low flare horns are preferred over high flare horns to give rise to low sidelobe performance for a given offset reflector antenna system.