Enhancing Effects of Ultrasound Treatment on the Preparation of TiO2 Photocatalysts

TiO₂ nanoparticles were synthesized by the hydrolysis and condensation of TiCl₄ in a mixed solvent of iso-propyl alcohol and water with or without ultrasound treatment. As-prepared powders were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy filtering transmission electron microscopy (EF-TEM), particle size analysis and BET surface area analysis. The specific surface area, thermal stability and crystallization of the as-prepared samples treated with ultrasound were higher than those of samples treated without ultrasound. To examine the photocatalytic activity of the as-prepared TiO₂, the photodegradation of MB which is a typical dye resistant to biodegradation has been investigated on TiO₂ powders in aqueous heterogeneous suspensions. The photocatalytic degradation of a aqueous solution of methylene blue shows a remarkable increase when it is carried out with ultrasound in all cases.     

Simple fabrication and photocatalytic activity of S-doped TiO2 under low power LED visible light irradiation

A series of S-doped TiO₂ with visible-light photocatalytic activity were prepared by a simple hydrolysis method using titanium tetrachloride (TiCl₄) and sodium sulfate (Na₂SO₄) as precursors. The photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), UV–vis diffuse reflectance spectrophotometer (UV–Vis DRS), and X-ray photoelectron spectroscopy (XPS). With the doping of S, photocatalysts with small crystal size, high content of anatase phase were obtained. The result showed that S-doped TiO₂ demonstrate considerably high photoactivity under low power visible LED light irradiation, while undoped TiO₂ and the Degussa P25 have nearly no activity at all. The possible mechanism of S-doped for the visible-light activity was discussed.     

Simple fabrication of N-doped mesoporous TiO2 nanorods with the enhanced visible light photocatalytic activity

N-doped mesoporous TiO₂ nanorods were fabricated by a modified and facile sol–gel approach without any templates. Ammonium nitrate was used as a raw source of N dopants, which could produce a lot of gasses such as N₂, NO₂, and H₂O in the process of heating samples. These gasses were proved to be vitally important to form the special mesoporous structure. The samples were characterized by the powder X-ray diffraction, X-ray photoelectron spectrometer, nitrogen adsorption isotherms, scanning electron microscopy, transmission electron microscopy, and UV-visible absorption spectra. The average length and the cross section diameter of the as-prepared samples were ca. 1.5 μm and ca. 80 nm, respectively. The photocatalytic activity was evaluated by photodegradation of methylene blue (MB) in aqueous solution. The N-doped mesoporous TiO₂ nanorods showed an excellent photocatalytic activity, which may be attributed to the enlarged surface area (106.4 m² g^-1) and the narrowed band gap (2.05 eV). Besides, the rod-like photocatalyst was found to be easy to recycle.     

Preparation of aerochitin‐TiO2 composite for efficient photocatalytic degradation of methylene blue

An aerochitin–titania (TiO₂) composite was successfully synthesized and characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, thermogravimetric analysis, field emission scanning electron microscopy, and N₂ adsorption isotherms. The photocatalytic activity of the composite was investigated on the degradation of the model organic pollutant, methylene blue (MB) dye, under UV irradiation. The aerochitin–TiO₂ composite showed excellent adsorptive and photocatalytic activity with a degradation degree of 98% for MB. The first‐order rate constants for the photodegradation MB by TiO₂ nanoparticles and aerochitin–TiO₂ composite were found to be (3.49 ± 0.04) × 10^?3 and (1.82 ± 0.02) × 10^?2 min^?1. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45908.     

Effect of M-doping (M = Fe,V) on the photocatalytic activity of nanorod rutile TiO2 for Congo red degradation under the sunlight

Nanorods TiO₂, Fe-TiO₂ (3 and 2 at.% Fe), V-TiO₂ (5 at.% V) were prepared by a low temperature method and characterized by powder X-ray diffraction, thermal analysis, transmission electron microscope and BTE surface area analysis. The as-prepared samples were evaluated as catalysts for photodegradation of Congo red aqueous solution under the sunlight. Nanorods Fe-doped TiO₂ shows higher adsorption and also higher photocatalytic degradation of Congo red solution compared to pure nanorods TiO₂ rutile. A higher activity is obtained when the amount of doped Fe is 2 at.%, compared to 3 at.%. However, nanorods V-TiO₂ does not show neither adsorption nor photodegradation activity of Congo red solution.     

Photoassisted mineralization of remazole red F3B over NiO/TiO2 and CdO/TiO2 nanoparticles under simulated sunlight

In this work, a series of titania-supported NiO and CdO materials were synthesized by a modified sol-gel process. The prepared photocatalysts were characterized by X-ray diffraction (XRD), UV-Vis diffuse reflectance spectroscopy (DRS), and transmission electron microscopy (TEM). The activities of titania-supported NiO and CdO photocatalysts for photocatalytic degradation of Remazole Red F3B (RR) dye, under simulated sunlight, were investigated. The photocatalytic mineralization of an RR dye solution over various NiO-x/TiO₂ and CdO-x/TiO₂ photocatalysts under simulated sunlight was investigated. It was worthy noticing that the photocatalytic activity of titania improved using the prepared catalysts. The prepared TiO₂, NiO-5/TiO₂, and CdO-2/TiO₂ photocatalysts exhibited higher photocatalytic activity under simulated sunlight than did commercial TiO₂. The prepared photocatalysts were stable after photocatalytic degradation of the dye. The observed photocatalytic mineralization of the dye was 51 and 71% over NiO-10/TiO₂ and CdO-2/TiO₂ after 180 min of irradiation, respectively. Juxtaposing a p-NiO-5/TiO₂ semiconductor provided a potential approach for decreasing charge recombination. The prepared photocatalystsNiO-5/TiO₂ and CdO-2/TiO₂ are promising composites for the solar detoxification of textile wastewater.     

Effect of peptisation on nanosized TiO2 particles prepared by hydrolysis from metatitanic acid

Abstract

Nanocrystalline TiO₂ particles were prepared by three methods: direct hydrolysis from metatitanic acid dissolved in the presence of concentrated sulphuric acid; hydrolysis of titanium sulphate (TiSO₄); and from powders obtained by peptising precipitates with hydrochloric acid and tetraethylammonium hydroxide to form crystal phases at lower temperatures. Samples were characterised by transmission electron microscopy, X-ray diffractometry, and Brunauer–Emmitt–Teller surface area analysis. In the photodegradation of anionic sodium dodecylbenzenesulphonate surfactant, nanosized TiO₂ with mixed anatase and rutile phases was found to show improved photocatalytic properties over commercial P-25 titania powder.     

Effects of I and F codoped TiO2 on the photocatalytic degradation of methylene blue

Nanocrystalline I-F-codoped TiO₂ was prepared by a sol-gel-impregnation method, using tetrabutylorthotitanate in a mixed NH₄I-NH₄F aqueous solution. The as-prepared TiO₂ was characterized with UV-vis diffuse reflectance spectra, X-ray diffraction and nitrogen adsorption. The degradation of methylene blue (MB) over as-prepared TiO₂ in aqueous solution under simulated sunlight irradiation was remarkably enhanced by codoping with I and F. The effects of codoping and calcination temperature on the photocatalytic activity and microstructures were investigated. The photocatalytic activity of as-prepared I-F-codoped TiO₂ was remarkably higher than that of pure, I-doped, and F-doped TiO₂ when the molar ratios of I and F to Ti were kept in the value of 10. The influence of I-F-modification on the photocatalytic activity was discussed by considering the higher surface area, entire anatase phase, effective dopant content, and stronger absorbance of sunlight, corresponding to the higher quantum efficiency. In addition to a complete removal of color, the as-prepared TiO₂ was simultaneously able to oxidize MB and small amounts of intermediates such as formic acid and phenol were detected. After prolonged sunlight irradiation some intermediates almost vanished, and MB appeared to be eventually mineralized to NH₄⁺, NO₃⁻ and SO₄²⁻.     

Photocatalytic degradation of methylene blue and acetaldehyde by TiO<Subscript>2</Subscript>/glaze coated porous red clay tile

Nanosized TiO₂ sol synthesized by sol-gel method was successfully coated on the porous red clay tile (PRC tile) with micrometer sized pores. PRC tile was first coated with a low-firing glaze (glaze-coated PRC tile) and then TiO₂ sol was coated on the glaze layer. A low-fired glaze was prepared at various blending ratios with frit and feldspar, and a blending ratio glazed at 700 °C was selected as an optimum condition. Then TiO₂ sol synthesized from TTIP was dip-coated on the glazed layer (TiO₂/glaze-coated PRC tile), and it was calcined again at 500 °C. Here, these optimum calcination temperatures were selected to derive a strong bonding by a partial sintering between TiO₂ sol particles and glaze layer. Photocatalytic activity on the TiO₂/glaze-coated PRC tile was evaluated by the extent of photocatalytic degradation of methylene blue and acetaldehyde. Methylene blue with the high concentration of 150 mg/l on the surface of TiO₂/glaze-coated PRC tile was almost photodegraded within 5 hours under the condition of average UV intensity of 0.275 mW/cm₂, while no photodegradation reaction of methylene blue occurred on the glaze-coated PRC tile without TiO₂. Another photocatalytic activity was also evaluated by measuring the extent of photocatalytic degradation of gaseous acetaldehyde. The photodegradation efficiency in TiO₂/glaze-coated PRC tile showed about 77% photocatalytic degradation of acetaldehyde from 45,480 mg/l to 10,536 mg/l after the UV irradiation of 14 hours, but only about 16% in the case of the glaze-coated PRC tile.     

Modified microwave method for the synthesis of visible light-responsive TiO2/MWCNTs nanocatalysts

Recently, TiO₂/multi-walled carbon nanotube (MWCNT) hybrid nanocatalysts have been a subject of high interest due to their excellent structures, large surface areas and peculiar optical properties, which enhance their photocatalytic performance. In this work, a modified microwave technique was used to rapidly synthesise a TiO₂/MWCNT nanocatalyst with a large surface area. X-ray powder diffraction, field-emission scanning electron microscopy, transmission electron microscopy and Brunauer-Emmett-Teller measurements were used to characterise the structure, morphology and the surface area of the sample. The photocatalytic activity of the hybrid nanocatalysts was evaluated through a comparison of the degradation of methylene blue dye under irradiation with ultraviolet and visible light. The results showed that the TiO₂/MWCNT hybrid nanocatalysts degraded 34.9% of the methylene blue (MB) under irradiation with ultraviolet light, whereas 96.3% of the MB was degraded under irradiation with visible light.     

Preparation, Characterization and Photocatalytic Activities of F-doped TiO2 Nanotubes

F-doped TiO₂ nanotubes were prepared by impregnation method. The prepared catalysts were characterized by XRD, TEM, and XPS. The photocatalytic activity of F-doped TiO₂ nanotubes was evaluated through the photodegradation of aqueous methyl orange. The experiments demonstrated that the F-doped TiO₂ nanotubes calcined at 300 °C possessed the best photocatalytic activity. Compared with pure TiO₂ nanotubes, the doping with F⁻ significantly enhanced the photocatalytic efficiency. The high photocatalytic activity was ascribed to several beneficial effects produced by F-doping: creation of oxygen vacancies, presence of Ti³⁺, and so on. An erratum to this article can be found at     

Preparation, characterization and activity evaluation of p–n junction photocatalyst p-CaFe2O4/n-ZnO

p–n junction photocatalyst p-CaFe₂O₄/n-ZnO was prepared by ball milling of ZnO in H₂O doped with p-type CaFe₂O₄. The structural and optical properties of the p–n junction photocatalyst p-CaFe₂O₄/n-ZnO were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis diffuse reflection spectrum (DRS) and fluorescence emission spectra. The photocatalytic activity of the photocatalyst was evaluated by photocatalytic degradation of methylene blue (MB). The results showed that the photocatalytic activity of the p-CaFe₂O₄/n-ZnO was higher than that of ZnO. When the amounts of doped p-CaFe₂O₄ were 0.0 wt.% and 1.0 wt.%, the photocatalytic degradation efficiencies were 50.1 and 73.4%, respectively. Effect of ball milling time on the photocatalytic activity of the photocatalyst was also investigated. The mechanisms of influence on the photocatalytic activity were also discussed by the p–n junction principle.     

Preparation of TiO2‐Coated Mo Powders for High Photocatalytic Property

An approach is introduced for fabricating the TiO₂‐coated molybdenum (Mo) powders via hydrothermal method, in which the Mo nanopowders were prepared by the electric explosion of wire method. The microstructure and photocatalytic properties of the samples were characterized by X‐ray diffraction, scanning electron microscopy, high‐resolution transmission electron microscopy, Raman spectroscopy (Raman), low temperature sorption of nitrogen (BET), and diffuse reflectance accessory of UV–Vis spectrophotometer. It was revealed that compared with pure TiO₂, the TiO₂‐coated Mo powders exhibited an improved photocatalytic activity, and the highest photocatalytic activity was achieved at the 1 wt% optimal mass percentage of the Mo nanopowders. The preparation of TiO₂‐coated Mo powders involved a relatively simple, economical, scalable, and also environment‐friendly approach.     

Shock-consolidated TiO2 bulk with pure anatase phases fabricated by explosive compaction using underwater shockwave

Titanium dioxide (TiO₂) bulk with pure anatase phases was fabricated by an explosive compaction technique using an underwater shockwave. Dynamic shock pressure of 6 GPa was used to consolidate anatase TiO₂ powders. Its microstructural, crystalline structural and photocatalytic characteristics were observed and measured by various techniques, such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and photocatalytic activity measurement system. It was confirmed that the relative density of anatase TiO₂ compact is about 96% (3.73 g/cm³) of the theoretical density (3.89 g/cm³) and a strong surface bonding between particles is formed by a shock energy. In X-ray diffraction analysis, high purity anatase phases, broadened peaks due to lattice defects and decreased crystallite size were found. For the photocatalytic activities, the anatase TiO₂ compact was quite excellent compared to the commercial sintered TiO₂ bulk.     

Photocatalytic activity of metal ion (Fe or W) doped titania

Iron or tungsten-doped nano TiO₂ were successfully synthesized from TiCl₄. All of the samples showed anatase phase of TiO₂. For the iron-doped TiO₂, Iron ion was well dispersed in the TiO₂ lattice. However, tungsten-doped TiO₂ formed 12-tungstate with anatase TiO₂. As the concentration of tungsten increased, 12-tungstate disappeared. The photocatalytic oxidation of acetaldehyde was evaluated to examine the photocatalytic characteristics of metal-doped TiO₂. Because of the surface containing metal oxide or metal precursors at high concentration metal ion, increasing the concentration of W or Fe ion decreased the reactivity. The reaction rate was drastically increased after 300 °C heat treatment. Furthermore, the photocatalytic activity of iron- or tungsten-doped TiO₂ was higher than that of synthesized pure TiO₂ and commercial TiO₂.     

Hydrothermal synthesis of S-doped TiO2 nanoparticles and their photocatalytic ability for degradation of methyl orange

A simple synthesis route to nanocrystalline S-doped TiO₂ photocatalysts by a hydrothermal method at 180 °C was developed and the photocatalytic activity of the obtained powders for the degradation of methyl orange was studied. The products were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The phase composition (anatase/rutile ratio) and the photocatalytic activity of the final materials were found to be markedly influenced by the amount of the incorporated sulphur. On increasing the S-dopant amount, the anatase/rutile ratio and the photocatalytic activity of the as-prepared powders increased.     

Construction of Z-scheme type CdS–Au–TiO2 hollow nanorod arrays with enhanced photocatalytic activity

The Z-scheme type CdS–Au–TiO₂ hollow nanorod arrays have been constructed on glass substrates by following these simple steps: firstly, highly ordered TiO₂ hollow nanorod arrays (THNAs) were synthesized by liquid phase deposition (LPD) using ZnO nanorod arrays as templates; then both Au core and CdS shell nanoparticles were achieved on the THNAs by in situ photodeposition. The prepared three-component films were characterized by field-emission scanning electron microscopy (FSEM), high-resolution transmission electron microscope (HRTEM), Raman scattering and ultraviolet–visible absorption spectrum. The results showed that Au–CdS core–shell nanoparticles were well dispersed on wall of anatase THNAs from top to bottom. The three-component nanojunction system was evaluated for their photocatalytic activity through the degradation of methylene blue (MB) in aqueous solution. It was found that the CdS–Au–TiO₂ three-component hollow nanorod arrays exhibited significantly enhanced photocatalytic activity compared with single (THNAs) and two components (Au-THNAs or CdS-THNAs) systems. Reasons for this enhanced photocatalytic activity were revealed by photoluminescence (PL) results of our samples.     

Large-scale preparation of nanoporous TiO2 film on titanium substrate with improved photoelectrochemical performance

Fabrication of three-dimensional TiO₂ films on Ti substrates is one important strategy to obtain efficient electrodes for energy conversion and environmental applications. In this work, we found that hierarchical porous TiO₂ film can be prepared by treating H₂O₂ pre-oxidized Ti substrate in TiCl₃ solution followed by calcinations. The formation process is a combination of the corrosion of Ti substrate and the oxidation hydrolysis of TiCl₃. According to the characterizations by scanning electron microscopy (SEM), X-ray diffraction (XRD), and diffuse reflectance spectroscopy (DRS), the anatase phase TiO₂ films show porous morphology with the smallest diameter of 20 nm and possess enhanced optical absorption properties. Using the porous film as a working electrode, we found that it displays efficient activity for photoelectrocatalytic decolorization of rhodamine B (RhB) and photocurrent generation, with a photocurrent density as high as 1.2 mA/cm². It represents a potential method to fabricate large-area nanoporous TiO₂ film on Ti substrate due to the scalability of such chemical oxidation process.     

Photocatalytic degradation of dyestuff wastewater under visible light irradiation using micron‐sized mixed crystal TiO2 powders

A phase transformation of micron‐sized TiO₂ powder from anatase to rutile was attempted by heat‐treatment in order to generate a new mixed crystal TiO₂ with high associated photocatalytic activity. Heat‐treated micron‐sized TiO₂ powders at different transition stages were characterized by X‐ray diffraction analysis (XRD), Fourier transform infrared spectroscopy (FT‐IR) and transmission electron microscopy (TEM) methods. The tests of photocatalytic activity of the heat‐treated micron‐sized TiO₂ powders were conducted by the photocatalytic degradation of Rhodamine B and Acid Red B under visible light irradiation. The results indicate that mixed crystal TiO₂ photocatalyst heat‐treated at 400 °C for 60 min shows the highest photocatalytic activity. It can effectively decompose the Rhodamine B and Acid Red B in aqueous solution after 6 h visible light irradiation. A remarkable improvement in photocatalytic activity of TiO₂ is caused by the formation of combined rutile–anatase phases and separation of photogenerated electron–hole pairs. Copyright © 2007 Society of Chemical Industry     

One-pot synthesis of CdS sensitized TiO2 decorated reduced graphene oxide nanosheets for the hydrolysis of ammonia-borane and the effective removal of organic pollutant from water

A hybrid material of reduced graphene oxide (RGO) sheets decorated with CdS-TiO₂ NPs was prepared through a facile one-pot hydrothermal method. The assembly of CdS-TiO₂ nanoparticles (NPs) on RGO sheets was in-situ produced. As-synthesized nanocomposites were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), energy disperse X-ray spectrum (EDS), fourier transform infrared spectroscopy (FTIR), and photoluminescence spectroscopy (PL). The obtained nanocomposites exhibited a good photocatalytic activity for the visible-light-induced decomposition of methylene blue (MB) dye and hydrolysis of ammonia borane. The results showed that by incorporation of CdS and TiO₂ NPs on graphene oxide sheets the photocatalytic efficiency was enhanced. The significant enhancement in the photocatalytic activity of CdS-TiO₂/RGO nanocomposites under visible light irradiation can be ascribed to the effect of CdS by acting as electron traps in TiO₂ band gap. Reduced graphene oxide worked as the adsorbent, electron acceptor and a photo-sensitizer to efficiently enhance the dye photo decomposition. Such nanocomposite photocatalyst might find potential application in a wide range of fields, including hydrogen energy generation, air purification, and wastewater treatment.