Grain growth in the two-phase Al-Cu alloys

Grain and phase growth in the two-phase Al-Cu alloys containing 6, 11, 1 7, 24 and 33 wt % Cu were investigated by annealing at 535 °C for 0.5–100 h. The grain and phase sizes of the phase are seen to be larger than that of the phase. The size of phase decreases whereas the size of phase increases with increasing copper content in the alloy. As such, the phase- and grain-size distributions are broader than the phase- and grain-size distributions, but the size range depends on annealing time and alloy composition. The grain sizes of the ,d , and ,d , phases can be related to the volume fraction of the phase,f , according to the equationd = 0.497d /f .     

Optimal design of a thick-walled pipeline cross-section against creep rupture

Summary Cylinder under combined loadings (pressure, bending, axial force) is subject to non-linear creep described by Norton-Odqvist creep law. In view of bending a circularly-symmetric cross-section is no longer optimal in this case. Hence we optimize the shape of the cross-section; minimal area being the design objective under the constraint of creep rupture. Kachanov-Sdobyrev hypothesis of brittle creep rupture is applied. The solution is based on the perturbation method (expansions into double series of small parameters), adjusted to optimization problems.Notation A cross-sectional area - C, , creep rupture constants - K, n, _C , _C creep constants - F dimensionless creep modulus - M bending moment - N axial force - a(),b() internal and external radii of the cross-section - j creep modulus - p internal pressure - r, ,z cylindrical coordinates - s _r ,s ,s _z ,t _r dimensionless stresses - t _R time to rupture - stress function - , () dimensionless internal and external radii - _e effective strain rate - _kl strain rates - rate of curvature - rate of elongation of the central axis - dimensionless radius - _e effective stress - _I maximal principal stress - _S Sdobyrev's reduced stress - _r , , _z , _r components of the stress tensor - measure of material continuity - measure of deterioration With 7 Figures     

Effect of crack shape,inclination angle,and friction coefficient in crack surface contact problems

In rolling/sliding contact fatigue, it is known that the crack propagates at a characteristic angle =15–30 deg to the surface. To analyze the mechanism, however, the body force method has been widely used assuming 3D crack models for =45–90. In this study, therefore, the unknown body force densities are newly approximated by using fundamental density functions and polynomials. Then, a semi-elliptical crack model is analyzed for =15–90 under compressive residual stresses and Hertzian contact loads. The stress intensity factors K _II, K _III are calculated with varying the crack shape b/a, inclination crack angle , and crack face friction coefficient . The calculations show that the present method is useful for the analysis for =15–30 deg with high accuracy. It is seen that the K _II-values when b/a0 are larger than the ones when b/a=1 by 0–24% for both under compressive residual stress and Hertzian contact load. Regarding the maximum K _II values under Hertzian contact load, the results of =15 deg are smaller than the ones of =45 deg by 23–34%. Regarding the amplitude of (K _{II max}–K _{II min}), the results of =15 deg are smaller than the ones of =45 deg by 4–24%. With increasing the value of friction coefficient for crack faces the value of K _II decreases significantly. When the crack is short and the inclination angle is small, the value of friction coefficient f for Hertzian contact load largely affect the K _II value.     

Hot electrons in metals at low temperatures

Hot electrons in metals at helium temperatures under steady conditions can be produced by passing an electric current of moderate density ( 10⁶ A/cm²) through thin, narrow (~1 m wide) metallic films in good thermal contact with bulk single-crystal dielectric substrates. This paper is concerned with the theory of hot electrons in normal metals at low temperatures (when _D, where is the average electron energy and _D is the Debye temperature). The theory is formulated in terms of realistic electron and phonon dispersion laws, taking into account the experimental possibility of heat removal from the sample. In the case in which the temperature approximation of Kagnov, Lifshitz, and Tanatarov is not satisfied when elastic scattering of electrons is dominant in a steady state electric field, the kinetic equation is derived for the energy-dependent, hot electron distribution function, which determines the associated nonlinear responses. The solution of this equation is discussed for a simple model. It is shown that the experimental information on the electron-phonon interaction in a metal can be obtained in terms of the well-known spectral functions S() ² F() and g() _tr ² F(). This is illustrated by experiments determining the nonlinear field dependence of the resistance, by tunnel experiments, and by critical current hysteresis measurements (for superconducting metals). Theoretical estimates which support the observability of the effects under discussion are presented.     

A calorimetric study of S′ and θ′ precipitation in Al2O3 particle-reinforced AA2618

Differential scanning calorimetry (DSC) was used to study the kinetics of S and precipitation in AA2618 and its composite containing 15 vol % Al₂O₃ particles . The unreinforced alloy and the composite were fabricated by a proprietary casting method, followed by extrusion. The DSC studies were carried out on as-quenched samples of the test materials. The precipitation of the S and phases in both materials was found to be kinetically controlled and obey the modified Avrami-Johnson-Mehl equation. The growth mechanisms for S and formation in AA2618 seemed unaffected by the addition of Al₂O₃ particles. The growth parameters obtained for the precipitation of these phases in the matrix alloy and the composite were not significantly different.     

Thermal stresses in a thin circular disc of orthotropic material due to an instantaneous point heat source

Summary In this paper, we have analysed the transient plane thermal stress problem of a circular disc of orthotropic material with instantaneous point heat source. The variation of with time along different radius vectors is exhibited graphically and compared with that of the isotropic case.

---

Wärmespannungen in einer dünnen Kreisscheibe aus orthotropem Material zufolge einer punktförmigen instantanen Wärmequelle

Zusammenfassung In dieser Arbeit wurde das instationäre ebene Wärmespannungsproblem einer Kreisscheibe aus orthotropem Material zufolge einer punktförmigen instantanen Wärmequelle untersucht. Die Veränderung von über die Zeit für verschiedene Radien ist graphisch dargestellt und wird mit dem isotropen Fall verglichen.

---

Nomenclature r, polar coordinates - T temperature rise - ² ratio of conductivities - ² thermal diffusivity in -direction - J _n Bessel function ofn-th order - t time - p introduced in equation (2) - h heat transfer coefficient - a radius of circular disc - f(r, ) temperature distribution at initial state - r ₀, ₀ a point on the disc - T ₀ strength of point heat source - Dirac delta function - F stress function in two dimensions - ₁, ₂ coefficient of thermal expansion - a ₁₁,a ₁₂,a ₂₂,a ₆₆ elastic constants With 9 Figures     

Analytical and graphical evaluation of local quasi-stable angular points during ion bombardment at oblique incidence

An implied analytical condition, connecting the incidence angles _o and _e between the two intersecting microfacet normals and the ion beam direction, has been inferred for the existence of local quasi-stable intersections (angular points) during ion erosion. This condition, which can also be deduced on the basis of the erosion slowness curve, leads to a higher degree algebraic equation with a parameter, applicable for any dependence S=S (), expressed as an algebraic polynomial expression in cos . A new graphical method for evaluation of orientations _e compatible with a given orientation _o, based on a known polar diagram cursor-type, has also been proposed.     

Directional dependence of c-plane slip in single crystals of mercuric iodide

An experimental study of plastic deformation in thin single crystals of mercuric iodide (Hgl₂) subjected to (0 0 1) [1 0 0] and (0 0 1) [1 1 0] shear loadings has established a directional dependence to the phenomenon of (0 0 1) orc-plane slip in Hgl₂. The average stressess _c for the onset of yielding were 12.6 psi (86.9 kPa) for (0 0 1) [1 0 0] shear and 16.5 psi (113.8 kPa) for (0 0 1) [1 1 0] shear; the average values of the deformation parameters ₀, interpreted as a bulk yield stress, were 24.7 psi (170.3 kPa) for (0 0 1) [1 0 0] shear and 37.7 psi (259.9 kPa) for (0 0 1) [1 1 0] shear. These values are in agreement with the theoretical relationss _c()=s _c(0)/cos ands ₀()=s ₀(0)/cos, where is the smallest angle between 1 0 0 crystallographic axis and the direction of shear stress applied in the (0 0 1) plane.     

Electrical conductivity,thermoelectric power and dielectric constant of NiWO4

The a.c. electrical conductivity ( _ac), thermoelectric power () and dielectric constant () of antiferromagnetic NiWO₄ are presented. _ac and have been measured in the temperature range 300 to 1000 K and in the temperature range 600 to 1000 K. Conductivity data are interpreted in the light of band theory of solids. The compound obeys the exponential law of conductivity = ₀ exp (–W/kT). Activation energy has been estimated as 0.75eV. The conductivity result is summarized in the following equation =2.86 exp (–0.75 eV/kT)^–1 cm^–1 in the intrinsic region. The material is p-type below 660 K and above 950 K, and is n-type between 660 and 950 K.     

Disappearance of Bose-Glass Behavior in Transport Properties of YBa2Cu3O y Films with Columnar Defects

The glass transitions of the vortex system in Au-ion irradiated YBa₂Cu₃O _y films have been studied by the measurements of transport properties as a function of magnetic field B and angle of B to the direction of columnar defects. At =0°, we find an anomalous upturn behavior of the glass transition line B _g(T) at BB /3, where B is the matching field. In B>B /3, the dependence of glass transition temperature T _g reveals cusplike behavior with a peak at =0°, which is consistent with the Bose glass theory. In B<B /3, on the other hand, T _g is almost independent of , suggesting the system undergoes the vortex glass transition induced by the inherent point-like defects.     

In-Plane Fourfold Symmetry of the Upper Critical Field Observed in La(Sr)214 Single Crystals

In order to establish the existence of in-plane anisotropy of the upper critical field H _c2 (), the out-of-plane resistivity _c measurements were performed on La(Sr)214 single crystals with rectangular and cylindrical shape under rotating magnetic field applied within the ab-plane. Although observed _c shows non-sinusoidal twofold symmetry, clear fourfold symmetry was obtained after subtracting twofold sinusoidal component in _c which is due to the unavoidable misalignment of the magnetic field with respect to ab-plane. H _c2 () is estimated from the extracted fourfold component of _c with the flux flow theory. Angular dependence of H _c2 () was well fitted by cos(4). Since the fourfold component of H _c2 () was largest at = n/2, which corresponds to the a-axis direction, the present results strongly suggest the type symmetry in La(Sr)214. In addition, the difference in fourfold component of H _c2 at = n/2 and n/2+/4 was found to increase with decreasing temperature.     

On the nucleation ofθ′ and T1 on Al3Zr precipitates in Al-Li-Cu-Zr alloys

Two quaternary Al-Li-Cu-Zr alloys have been investigated using electron microscopy. Ageing at 190° C resulted in the nucleation of precipitates on the Al₃Zr/matrix interface in addition to heterogeneous nucleation on matrix dislocations. In the majority of cases, the broad, coherent face of the plans ms in contact with the Al₃Zr precipitates. Similar evidence showed that nucleation of T₁ precipitates occurred on the Al₃Zr, but to a lesser extent than. Solid-solid nucleation theory has been used to account for the Al₃Zr acting as a nucleation substrate.     

Numerical method for solving heat-conduction problems for two-dimensional bodies of complex shape

A finite-difference scheme is described for a curvilinear orthogonal net which permits the use of a single algorithm for calculating bodies of various shapes.Notation x, y independent variables - u, v orthogonal coordinates - F(w)=F(u + iv) function of a complex variable - g(u,v)= F(w)/w Jacobian of transformation from (u,v) to (x,y) - thermal conductivity - c volumetric heat capacity - Q heat release per unit volume - T temperature - f value of temperature on boundary of region - time - L, L₁, L₂ differential operators - (u,v) solution of differential problem in canonical region - ^j, ₁ ^j , ₂ ^j , t^J, t ₁ ^j , t ₂ ^j network functions in canonical region - ^j, t^*j solutions of difference problems using rectangular and orthogonal nets respectively - {u_i, v_k} rectangular net in canonical region G - {x_i,k, y_i, k} orthogonal net in given region G^* - u_i, v_k dimensions of cell of rectangular net - u_i,v _i,k dimensions of cell of orthogonal net - h, maximum dimension of cell for rectangular and orthogonal nets respectively - ₁, ₂, difference operators for rectangular and orthogonal nets - A, B, C, D, A^*, B^*, C^*, D^* coefficients of difference scheme for rectangular net - D, Ã, B coefficients of difference scheme for orthogonal net Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 40, No. 3, pp. 503–509, March, 1981.     

On the analysis of tunneling data for A15 superconductors

We examine the applicability of the standard McMillan inversion of Eliashberg's equations for superconductors with a nonconstant electronic density of statesN(). We do this usign simple models forN() and a realistically shapedN() taken from recent band structure work for Nb₃Sn. It turns out that peak structure inN() near _F may lead to gross errors in the derived Eliashberg function ²F() when the energy dependence ofN() is omitted in the inversion procedure. For Nb₃Sn, this leads to a 40% overestimate of when ²F() is evaluated via the standard McMillan program.     

Application of the Monte Carlo method for calculating the shape of the heat source generated by the action of electron beams on a substance

The space distribution of energy absorbed in a substance during the passage of an electron beam has been determined with the aid of the Monte Carlo method.Notation f_H-S density of Haudsmith-Saunderson distribution - _e (cos) Legendre polynomials - z, A atomic number and atomic weight of an element - =v/c ratio of electron velocity to velocity of light - E_k kinetic energy of an electron, MeV - I(z) mean ionization potential of atoms in the medium - E plasmon energy - k_c wavelength corresponding to effective interception - a ₀ Bohr radius - m₀ quiescent mass of an electron - deflection angle of electron within an interval Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 22, No. 6, pp. 1110–1113, June, 1972.     

A numerical solution of the blade-to-blade flow in turbomachines by the application of a transformation on the S1 stream surface

Summary The solution of the blade-to-blade (quasi-3-dimensional) steady, inviscid flow in turbomachines is considered as a quantitative prediction of the flow and as a good approximation of the real three-dimensional flow. The well known governing differential equation is of elliptic type and its numerical solution is a rather difficult problem (taking also into account the complex form of the S1 stream surface). By the procedure proposed, the S1 stream surface in the (m, ) coordinate system is transformed into a rectangular (x,, y, space, by the application of the following transformation:x=m/L, (–₁)/(₂–₁), where₁ and ₂ are the angular positions of the lines limiting the S1 surface, andL the length of the meridional projection of the blade.By the introduction of this transformation, extra terms are added to the differential equation, but now the definition of the grid is easier. From the transformed differential equation, a system of algebraic equations is obtained applying the finite volume method. The system of algebraic equations is solved by a relaxation method with periodic boundary conditions. The grid applied in the (x, y) coordinate system is not of uniform density in order to define better the geometry of the blades near the leading and trailing edges. Finally the results from the application of the procedure on a centrifugal, mixed flow pump are presented; i.e. relative velocity and static pressure distribution along the blade surfaces.With 11 Figures     

Nonlinear asymptotic theory of hypersonic flow past a circular cone

Summary The hypersonic small-disturbance theory is reexamined in this study. A systematic and rigorous approach is proposed to obtain the nonlinear asymptotic equation from the Taylor-Maccoll equation for hypersonic flow past a circular cone. Using this approach, consideration is made of a general asymptotic expansion of the unified supersonic-hypersonic similarity parameter together with the stretched coordinate. Moreover, the successive approximate solutions of the nonlinear hypersonic smalldisturbance equation are solved by iteration. Both of these approximations provide a closed-form solution, which is suitable for the analysis of various related flow problems. Besides the velocity components, the shock location and other thermodynamic properties are presented. Comparisons are also made of the zeroth-order with first-order approximations for shock location and pressure coefficient on the cone surface, respectively. The latter (including the nonlinear effects) demonstrates better correlation with exact solution than the zeroth-order approximation. This approach offers further insight into the fundamental features of hypersonic small-disturbance theory.Notation a speed of sound - H unified supersonic-hypersonic similarity parameter, - K hypersonic similarity parameter, M - M freestream Mach number - P pressure - T temperature - S entropy - u, v radial, polar velocities - V freestream velocity - shock angle - cone angle - density - density ratio, /() - ratio of specific heats - polar angle - stretched polar angle, / - (), (), () gage functions     

A superconducting vibrating reed applied to flux-line pinning. I. Theory

A theoretical treatment is given of a superconducting reed clamped at one end and performing flexural vibrations in a homogeneous longitudinal magnetic fieldB _a. When the flux lines are rigidly pinned the reed behaves like an ideal diamagnet whose bending distorts the external field. This generates a magnetic restoring force (line tension) B _a ² which is independent of the reed thicknessd, whereas the mechanical restoring force (stiffness) is d ³. Therefore, the resonance frequency /2 of a thin superconducting reed increases drastically when a fieldB _a is applied, or for a givenB _a, when the reed is cooled below its critical temperatureT _c. With decreasing pinning strength (characterized by Labusch's parameter ) the resonance frequency decreases, ²²– _pin ² where _pin ^{2 –1}, and an attenuation _v ^–2 occurs due to the viscous motion of flux lines. For larger vibration amplitudes an additional, amplitude-dependent damping _h ^–3 occurs due to the hysteretic losses caused by elastic instabilities during flux motion.On leave from Centro Atómico, Bariloche, Argentina.     

Die Herleitung von Schalengleichungen über ein erweitertes Variationsprinzip bei Berücksichtigung der Querschubverzerrungen

Ohne ZusammenfassungBezeichnungen L Bezugsgrößen für dimensionslose Koordinaten - L charakteristische Schalenabmessung - t Schalendicke - Schalenparameter - körperfeste, krummlinige, dimensionslose Koordinaten der Schalenmittelfläche - Dimensionslose Koordinate in Richtung der Schalennormalen - i, j,...=1,2,3 Indizierung des dreidimensionalen Euklidischen Raumes - ,,...=1,2 Indizierung des zweidimensionalen Riemannschen Raumes - (...), Partielle Differentiation nach der Koordinate - (...), Kovariante Differentiation für Tensorkomponenten des zweidimensionalen Raumes nach der Koordinate - (...)| Kovariante Differentiation für Tensorkomponenten des dreidimensionalen Raumes nach der Koordinate - Variationssymbol - a ,a ₃ Basisvektoren der Schalenmittelfläche - V Verschiebungsvektor - U ,U ₃ Verschiebungskomponenten des Schalenraumes - v ,w,w ,W Verschiebungskomponenten der Schalenmittelfläche - Verhältnis der Metriktensoren des Schalenraumes und der Schalenmittelfläche - _ik Verzerrungstensor des Raumes - _{(, )}, Symmetrische Verzerrungstensoren der Schalenmittelfläche - _{[, ]} Antimetrischer Term des Verzerrungsmaßes - ^, Spannungstensor - n ,m ,q Tensorkomponenten der Schnittgrößenvektoren - p ,p,c Tensorielle Lastkomponenten     

Heat transfer in a “pseudoturbulent” bed of dispersed material

A two-phase model is proposed for the steady heat exchange between a surface and a pseudoturbulent bed of dispersed material. Expressions are obtained for the temperature fields of the gaseous and solid phases.Notation _g effective thermal conductivity of gaseous phase - _s effective thermal conductivity of the mixed solid phase - porosity - _m molecular thermal conductivity - d particle diameter - temperature of dispersed bed at a large distance from heat source - , g gas temperature - _p particle temperature - _w wall temperature - x current coordinate in the direction perpendicular to the wall - l bed thickness - q heat flux - coefficient of heat exchange between wall and pseudoturbulent bed of dispersed material - ^* coefficient of interphase heat exchange - _g=_g/_w dimensionless gas temperature - _p = _p/_w dimensionless particle temperature - Y = x/d dimensionless coordinate - L =l/d dimensionless bed thickness - A_h dimensionless coefficient of interphase heat exchange - Nu_g = d/_s Nusselt number Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 465–469, September, 1981.