Large enhancement of upconversion luminescence in Er<Superscript>3+</Superscript>/In<Superscript>3+</Superscript>:Ba<Subscript>0.85</Subscript>Ca<Subscript>0.15</Subscript>TiO<Subscript>3</Subscript> lead-free piezoelectric ceramics

A series of In³⁺-doped Ba_0.85Ca_0.15TiO₃:0.75%Er³⁺/xIn³⁺ (BCT:Er/xIn) lead-free piezoelectric ceramics with excellent upconversion luminescence were synthesized by the solid state reaction method. The effects of In³⁺ content on the crystal structure, ferroelectric, dielectric, piezoelectric, and upconversion luminescence properties were systematically studied. Under 980 nm excitation, a giant enhancement of the green emission (550 nm) by 10 times is achieved upon 2.5% mol In³⁺ doping, which is rarely observed in rare-earth ions-doped perovskite ferroelectric materials. The ultraviolet-visible-near infrared absorption measurements show that the In³⁺ doping may improve the dissolution of Er³⁺ ions and modify the isolate-/clustered-Er³⁺ ratio for x?≤?2.5%, resulting in the enhancement of the absorption cross-section, thereby contributing to the enhancement of green luminescence. Unfortunately, the In³⁺ doping suppresses the ferroelectric and piezoelectric properties of the BCT:Er/xIn ceramics. This problem can be resolved by adding a small amount (1 mol%) of Yb³⁺ to the BCT:Er/xIn ceramics to restore their good ferroelectric and piezoelectric properties. Such In³⁺ and rare-earth ions co-doped ceramics with greatly enhanced upconversion luminescence and good ferroelectricity and piezoelectricity may have potential applications in electro-optical devices.     

Strong up-conversion luminescence and electrical properties of SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> multifunctional ceramics by Er<Superscript>3+</Superscript> doping

Novel green-emitting piezoelectric ceramics of SrBi_4?x Er _x Ti₄O₁₅ (SBT-xEr) were prepared. Strong up-conversion with bright green (524 and 548 nm) and a relatively weak red (660 nm) emission bands were obtained under 980 nm excitation at room temperature, which is attributed to the intra 4f–4f electronic transition of (²H_11/2, ⁴S_3/2)–⁴I_15/2 and the transition from ⁴F_9/2 to ⁴I_15/2 of Er³⁺ ions, respectively. Simultaneously, Er³⁺ doping promotes the electrical properties. At 0.8 mol%Er, the optimal electric properties with high Curie temperature of T _c?~527?°C, large remanent polarization of 2P _r?~14.92 μC/cm² and piezoelectric constant of d ₃₃?~17 pC/N was achieved. As a multifunctional material, Er³⁺ doped SBT showed a great potential to be used in 3D-display, bio-imaging, solid state laser and optical temperature sensor.     

Properties of fluorine-doped PbMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript> ceramics

We report the first fluorine doping of lead magnesium niobate in the PbMg _{(1 + x)/3}Nb_{(2 ? x)/3}O_{3 ? x} F _x system in a wide composition range, x = 0.025 to 0.625. The fluorine content of the samples is shown to be substantially lower than the intended one because of the fluorine volatilization in the form of HF during synthesis and sintering in air. The ceramics consist of magnesium and lead oxides undetectable by x-ray diffraction, and a perovskite phase whose composition can be represented by the formula PbMg_{(1 + m)/3}Nb_{(2 ? m)/3}O_{3 ? m} F _m , where the fluorine content after sintering is m ≤ 0.12. The PbO and MgO contents of the ceramics depend on the starting mixture composition (x) and heat-treatment conditions (hydrogen fluoride and lead oxide volatilization). As a result of the low fluorine content, the diffraction patterns of the samples show no superlattice reflections, and their lattice parameter varies insignificantly with x. Data are presented on the temperaturedependent dielectric permittivity of ceramic samples sintered and annealed under different conditions.     

Structure and electrical properties of MnO doped (Ba<Subscript>0.96</Subscript>Ca<Subscript>0.04</Subscript>)(Ti<Subscript>0.92</Subscript>Sn<Subscript>0.08</Subscript>)O<Subscript>3</Subscript> lead free ceramics

In this work, (Ba_0.96Ca_0.04)(Ti_0.92Sn_0.08)O₃–xmol MnO (BCTS–xMn) lead-free piezoelectric ceramics were fabricated by the conventional solid-state technique. The composition dependence (0 ≤ x ≤ 3.0 %) of the microstructure, phase structure, and electrical properties was systematically investigated. An O–T phase structure was obtained in all ceramics, and the sintering behavior of the BCTS ceramics was gradually improved by doping MnO content. In addition, the relationship between poling temperature and piezoelectric activity was discussed. The ceramics with x = 1.5 % sintering at temperature of 1330 °C demonstrated an optimum electrical behavior: d ₃₃ ~ 475 pC/N, k _p ~ 50 %, ε _r ~ 4060, tanδ ~ 0.4 %, P _r ~ 10.3 μC/cm², E _c ~ 1.35 kV/mm, T _C ~ 82 °C, strain ~0.114 % and \(d_{33}^{*}\) ~ 525 pm/V. As a result, we achieved a preferable electric performance in BaTiO₃-based ceramics with lower sintering temperature, suggesting that the BCTS–xMn material system is a promising candidate for lead-free piezoelectric ceramics.     

Effect of Ni Doping at Pd Site in Nb<Subscript>2</Subscript>PdS<Subscript>5</Subscript> Superconductor

The superconducting properties of Nb₂PdS₅ superconductor have been investigated with Ni doping at Pd site All the bulk polycrystalline Nb₂Pd_1?xNi_x S ₅ (0 = x ≤ 0.10) samples are crystallized in singlephase monoclinic structure. The electrical resistivity and magnetic measurements of Nb₂Pd_1?xNi_x S ₅ (0 = x ≤ 0.15) were carried out to study the variation of superconducting critical parameters with Ni doping. Superconductivity in Nb₂PdS₅ sample completely disappears for x ≥ 0.15. We observed that the ratio of upper critical field to transition temperature decreases with increasing Ni concentration. Also, the magnetization study of Nb₂Pd_1?xNi_x S ₅ (0 = x ≤ 0.15) samples shows similar superconducting behaviour. In summary, the superconductivity in Nb₂PdS₅ sample is slightly varying with partial doping of Ni at Pd site in Nb₂PdS₅ superconductor.     

Electric-field effect on crystal growth in the Li<Subscript>3</Subscript>PO<Subscript>4</Subscript>-Li<Subscript>4</Subscript>GeO<Subscript>4</Subscript>-Li<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-LiF system

We have studied the electric-field effect on crystallization processes in the Li₃PO₄-Li₄GeO₄-Li₂MoO₄-LiF system. In zero field, Li_3+x P_1?x Ge _x O₄ (x = 0.31) crystals were grown on the cathode under the conditions of this study. At low applied voltages (≤ 0.5 V), we obtained Li₂MoO₄, Li₂GeO₃, and Li_1.3Mo₃O₈. In the range V = 0.5–1 V, crystals of Li_3+x P_1?x Ge _x O₄ solid solutions with x = 0.17, 0.25, 0.28, 0.29, and 0.36 were obtained. An applied electric field was shown to reduce the melting temperature of the starting mixtures and the crystallization onset temperature.     

Influence of isovalent and heterovalent substitution for Bi<Superscript>3+</Superscript> and Fe<Superscript>3+</Superscript> on the properties of Bi<Subscript>2</Subscript>Fe<Subscript>4</Subscript>O<Subscript>9</Subscript>-based solid solutions

Bi_2–хLa_хFe₄O₉ and Bi₂Fe_4–2xTi_xCo_xO₉ ferrites have been prepared by solid-state reactions at a temperature of 1073 K. X-ray diffraction data indicate that, in the Bi_2–хLa_хFe₄O₉ system, the limiting degree of La³⁺ substitution for Bi³⁺ ions in Bi₂Fe₄O₉ does not exceed 0.05 and that the limiting degree of substitution in the Bi₂Fe_4–2xTi_xCo_xO₉ system lies in the range 0.05 < x < 0.1. The specific magnetization and specific magnetic susceptibility of the samples have been measured at temperatures from 5 to 300 K in a magnetic field of 0.86 T. The field dependences of magnetization obtained for the Bi_2–хLa_хFe₄O₉ and Bi₂Fe_4–2xTi_xCo_xO₉ ferrites at temperatures of 300 and 5 K demonstrate that partial isovalent substitution of La³⁺ for Bi³⁺ ions in Bi₂Fe₄O₉ and heterovalent substitution of Ti⁴⁺ and Co²⁺ ions for two Fe³⁺ ions leads to partial breakdown of the antiferromagnetic state and nucleation of a ferromagnetic state.     

New NaSrPO<Subscript>4</Subscript>:Sm<Superscript>3+</Superscript> phosphor as orange-red emitting material

Sm³⁺-activated NaSrPO₄ phosphors could be efficiently excited at 403 nm, and exhibited a bright red emission mainly including four wavelength peaks of 565, 600, 646 and 710 nm. The highest emission intensity was found for NaSr _1?x PO₄: xSm³⁺ with a composition of x = 0.007. Concentration quenching was observed as the composition of x exceeds 0.007. The decay time values of NaSr_1?x PO ₄ : xSm³⁺ phosphors range from around 2.55 to 3.49 ms. NaSr_1?x PO₄: xSm³⁺ phosphor shows a higher thermally stable luminescence and its thermal quenching temperature T ₅₀ was found to be 350°C, which is higher than that of commercial YAG:Ce³⁺ phosphor and ZnS:(Al, Ag) phosphor. Because NaSr_1?x PO₄: xSm³⁺ phosphor features a high colour-rendering index and chemical stability, it is potentially useful as a new scintillation material for white light-emitting diodes.     

Synthesis and microwave dielectric properties of Zn<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>Nb<Subscript>2</Subscript>O<Subscript>6+<Emphasis Type="Italic">x</Emphasis></Subscript>

We have studied the formation of zinc niobate, ZnNb₂O₆, with the columbite structure and the microstructure and microwave dielectric properties of Zn_1+x Nb₂O_6+x ceramics. The results demonstrate that, in the range 0.005 ≤ x ≤ 0.03, the excess zinc reduces the porosity of the material and increases its microwave quality factor Q. For x ≥ 0.03, the Q of the ceramics decreases because of the formation of an additional, zinc-enriched phase. Sintering in an oxygen atmosphere is shown to improve the dielectric properties of stoichiometric ZnNb₂O₆.     

Very high thermal stability with excellent dielectric,and non-ohmics properties of Mg-doped CaCu<Subscript>3</Subscript>Ti<Subscript>4.2</Subscript>O<Subscript>12</Subscript> ceramics

In this work, the nominal CaCu_3?xMg_xTi_4.2O₁₂ (0.00, 0.05 and 0.10) ceramics were prepared by sintering pellets of their precursor powders obtained by a polymer pyrolysis solution method at 1100 °C for different sintering time of 8 and 12 h. Very low loss tangent (tanδ)?<?0.009–0.014 and giant dielectric constant (ε′) ～?1.1?×?10⁴–1.8?×?10⁴ with excellent temperature coefficient (Δε′) less than ±?15% in a temperature range of ??60 to 210 °C were achieved. These excellent performances suggested a potent application of the ceramics for high temperature X8R and X9R capacitors. It was found that tanδ values decreased with increasing Mg²⁺ dopants due to the increase of grain boundary resistance (R_gb) caused by the very high density of grain, resulting from the substitution of small ionic radius Mg²⁺ dopants in the structure. In addition, CaCu_3?xMg_xTi_4.2O₁₂ ceramics displayed non-linear characteristics with the significant enhancements of a non-linear coefficient (α) and a breakdown field (E_b) due to Mg²⁺doping. The high values of ε′ (14012), α (13.64) and E_b (5977.02 V/cm) with very low tanδ value (0.009) were obtained in a CaCu_2.90Mg_0.10Ti_4.2O₁₂ ceramic sintered at 1100 °C for 8 h.     

Effect of Al Substitution in Structural and Magnetic Properties of MnCr<Subscript>2</Subscript>O<Subscript>4</Subscript>

Single-phase samples of Mn(Cr_1?x Al _x )₂O₄ (x = 0 – 0.30) with cubic spinel structure were prepared and the lattice constant is found to decrease from a = 8.4396 Å for x = 0 to a = 8.3801 Å for x = 0.30. The substitution of Al at Cr site is confirmed from the blue shift of Raman modes. Magnetization measurements and analysis show all the prepared samples exhibit ferrimagnetic transition with transition temperature in the range of 46 K for x = 0 to 33 K for x = 0.30. The saturation magnetization (M _s ) and the estimated anisotropy constant (K) show an anomalous behavior up to x = 0.10 and beyond that they decrease monotonously. They are explained by considering different site preferences of Al ³⁺ ions as the doping concentration is increased. The theoretical and experimental effective magnetic moment of the samples is found to be comparable and it decreases with increase in Al concentration.     

NaF induced enhancement of luminous efficiency in narrow-band red-emitting K<Subscript>2</Subscript>TiF<Subscript>6</Subscript>:Mn<Superscript>4+</Superscript>@NaF phosphors

A series of K₂TiF₆:xMn⁴⁺ @NaF samples were prepared by the cation exchange method in HF solution. Coating effects of NaF on the fluorescent properties of the samples were discussed. It is interesting that NaF has induced enhancement of luminous efficiency for the samples. Mechanism of NaF induced enhanced luminescence effect was suggested. That is that the enhancement effect of NaF coating is mainly attributed to a suitable local distortion of the crystal field surrounding the Mn⁴⁺ activator through doping with NaF. The results indicate that the optimal conditions are x?=?0.07 and w_NaNO3?=?2.5 g. Decay lifetime and the photoluminescence quantum yield of the optimal sample are 5.25 ms and 99.19?±?0.03%, respectively. The chromaticity coordinates of the optimal sample are x?=?0.6926, y?=?0.3073. So, the phosphor emits deep red light, which can be applied for blue light-based white LED.     

Effect of Ni<Superscript>2+</Superscript> substitution on crystal structure and microwave dielectric properties for MgZrNb<Subscript>2</Subscript>O<Subscript>8</Subscript> ceramics

Monoclinic structured Mg_1?xNi_xZrNb₂O₈ (0?≤?x?≤?0.12) ceramics were synthesized for the first time through traditional solid-state reaction process and pure phase were obtained in all range. Rietveld refinement was used to analyze the crystal structure. With the increase of Ni²⁺ substitution amount, ε _r decreased, Q?×?f rose first then fell, τ _f shifted for the positive direction. Bond ionicity, lattice energy and bond energy were separately calculated to investigate the correlations with microwave dielectric properties. Typically, ceramics samples with the composition of Mg_0.92Ni_0.08ZrNb₂O₈ sintered at 1280 °C for 4 h exhibited the optimum microwave dielectric properties: ε _r ?=?24.58, Q?×?f?=?74534.1 GHz, τ _f ?=???49.11 ppm/°C, which could be a promising material for application.     

Effect of Ho-doping on structural,electrical and magnetic properties of La<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> ceramics prepared by Plasma-Activated Sintering

Different components of La_0.7?x Ho _x Sr_0.3MnO₃ (LHSMO, x = 0, 0.1, 0.2, 0.3) ceramics were fabricated by Plasma-Activated Sintering (PAS), so as to study the correlation between the contents of Ho³⁺ and the structural, electrical, magnetic properties. XRD and SEM confirmed that LHSMO ceramics prepared by PAS exhibited high-purity phase and dense microstructure. The measurement of electrical resistivity showed that the resistivity of LHSMO ceramics increased, and the metal–insulator transition temperature decreased with the increasing Ho-doping content. The resistivity data were then fitted using various empirical equations, and the conduction mechanism of LHSMO ceramics was found to be in accord with the electron–magnon scattering process in the low-temperature region and the small polaron hopping model in the high-temperature region. Lastly, we calculated the values of magnetoresistance of the LHSMO ceramics, which increased with increasing Ho-doping content, from 3.5% for x = 0 to 14.6% for x = 0.3. Therefore, the doping of Ho³⁺ into La_0.7Sr_0.3MnO₃ can effectively enhance the low-field magnetoresistance effect.     

Effects of Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> doping on the microstructure and electrical properties of (Ba,Ca)(Zr,Ti)O<Subscript>3</Subscript> lead-free ceramics

Lead-free ceramics (Ba_0.85Ca_0.15)(Zr_0.1Ti_0.9)O₃?x wt.%Cr₂O₃ (BCZT-xCr) were prepared via the conventional solid-state reaction method. The microstructure and electrical properties of BCZT-xCr samples were systematically studied. XRD and Raman results showed that all samples possessed a single phased perovskite structure and were close to the morphotropic phase boundary (MPB). With the increase of the Cr content, the rhombohedral-tetragonal phase transition temperature (T _R-T) increases slightly, and the Curie temperature (T _C) shifts towards the low temperature side. XPS analysis reveals that Cr³⁺ and Cr^{5 +} ions co-existed in Cr-doped BCZT ceramics, indicating the different impact on the electrical properties from Cr ions as “acceptor” or “donor”. For the x = 0.1 sample, relative high piezoelectric constants d ₃₃ (～316 pC/N) as well as high Q _m (～554) and low tanδ (～0.8%) were obtained. In addition, the AC conductivity was also investigated. Hopping charge was considered as the main conduction mechanism at low temperature. As the temperature increases, small polarons and oxygen vacancies conduction played important roles.     

Inducement of Itinerant Electron Transport in Charge-Ordered Pr<Subscript>0.6</Subscript>Ca<Subscript>0.4</Subscript>MnO<Subscript>3</Subscript> by Ba Doping

The effects of Ba ²⁺ doping on the electrical and magnetic properties of charge-ordered Pr_0.6Ca_0.4MnO₃ were investigated through electrical resistivity and AC susceptibility measurements. X-ray diffraction data analysis showed an increase in unit cell volume with increasing Ba ²⁺ content indicating the possibility of substituting Ba ²⁺ for the Ca-site. Electrical resistivity measurements showed insulating behavior and a resistivity anomaly at around 220 K. This anomaly is attributed to the existence of charge ordering transition temperature, \(T^{\mathrm {R}}_{\text {CO}}\) for the x = 0 sample. The Ba-substituted samples exhibited metallic to insulator transition (MI) behavior, with transition temperature, T _MI, increasing from ～98 K (x = 0.1) to ～122 K (x = 0.3). AC susceptibility measurements showed ferromagnetic to paramagnetic (FM-PM) transition for Ba-substituted samples with FM-PM transition temperature, T _c, increasing from ～121 K (x = 0.1) to ～170 K (x = 0.3), while for x = 0, an antiferromagnetic to paramagnetic transition behavior with transition temperature, T _N, ～170 K was observed. In addition, inverse susceptibility versus T plot showed a deviation from the Curie–Weiss behavior above T _c, indicating the existence of the Griffiths phase with deviation temperature, T _G, increasing from 160 K (x = 0.1) to 206 K (x = 0.3). Magnetoresistance, MR, behavior indicates intrinsic MR mechanism for x = 0.1 which changed to extrinsic MR for x > 0.2 as a result of Ba substitution. The weakening of charge ordering and inducement of ferromagnetic metallic (FMM) state as well as increase in both T _c and T _MI are suggested to be related to the increase of tolerance factor, τ, and increase of e _g ?electron bandwidth as average ionic radius at A-site, <r _A> increased with Ba substitution. The substitution may have reduced MnO₆ octahedral distortion and changed the Mn–O–Mn angle which, in turn, promotes itinerancy of charge carrier and enhanced double exchange mechanism. On the other hand, increase in A-site disorder, which is indicated by the increase in σ ² is suggested to be responsible for the widening of the difference between T _c and T _MI.     

Preparation and electrical properties of Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> solid solutions

Ceramic samples of lead magnesium niobate (PMN) and (1 ? x)Pb(Mg_1/3Nb_2/3)O₃?xPbTiO₃ (PMN-PT) solid solutions with x = 0, 0.05, 0.10, and 0.30 have been prepared by solid-state reactions, and their structural, electrical, and piezoelectric properties have been studied using x-ray diffraction, Rietveld profile analysis, impedance spectroscopy, and the resonance/antiresonance method. The results indicate that the use of nonstoichiometric columbite niobates enables the synthesis of phase-pure PMN and PMN-PT.     

Solid-state reactions in the system Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>

The formation mechanisms of Li _x Na_{1 ?x} Ta _y Nb_{1 ? y} O₃ perovskite solid solutions in the Li₂CO₃-Na₂CO₃-Nb₂O₅-Ta₂O₅ system have been studied by x-ray diffraction, differential thermal analysis, thermogravimetry, IR spectroscopy, and mass spectrometry at temperatures from 300 to 1100°C. The results indicate that the synthesis of Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions involves a complex sequence of consecutive and parallel solid-state reactions. An optimized synthesis procedure for Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions is proposed.     

Solid-state synthesis,characterization, and properties of Ni<Subscript>4</Subscript>Nb<Subscript>2</Subscript>O<Subscript>9</Subscript>-based solid solutions

In this paper, we report the solid-state synthesis, characterization, and physicochemical properties of Ni_4–x Zn _x Nb₂O₉ (x = 0, 0.1, 0.3, 0.5, 0.75, 1.0) zinc-containing nickel niobates and Ni₄Nb_2–x Ta _x O₉ (x = 0.1, 0.3, 0.5, 1.0, 2.0) solid solutions. The materials were characterized by X-ray diffraction. We determined the particle size composition of the synthesized powders, assessed their chemical stability in acid media, obtained IR spectra of the solid solutions, and measured their electrical conductivity as a function of temperature. Some of the solid solutions were used to fabricate and characterize nickel-selective electrodes, which were successfully tested in ion-selective measurements.     

Synthesis of anisotropic NaNbO<Subscript>3</Subscript> seed crystals and fabrication of textured (K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)NbO<Subscript>3</Subscript>-based ceramics

High aspect ratio patelike NaNbO₃ particles with pure perovskite structure have been successfully synthesized by topochemical microcrystal conversion (TMC) from plate-like precursor particles of the layer-structured Bi_2.5Na_3.5Nb₅O₁₈. By changing the Bi_2.5Na_3.5Nb₅O₁₈/Na₂CO₃ ratio, large and thin NaNbO₃ particles with a thickness of approximately 0.5 μm and a width of approximately 20 μm were obtained. The obtained NaNbO₃ particles is quite suitable for fabricating textured (K_0.5Na_0.5)NbO₃-based ceramics. Using the fine platelike NaNbO₃ particles as templates, dense <001> -oriented (K_0.5Na_0.5)NbO₃-0.5 mol %MnO₂ ceramics with high texture quality (Lotgering factor F ₀₀₁ = 87 %) and excellent piezoelectric properties were produced by templated grain growth. Compared with randomly oriented ceramics, textured samples show greatly enhanced properties. The room-temperature strain S, the piezoelectric coefficient d ₃₃ ^* and d ₃₃ reach up to 0.093 %, 233 pm/V and 195pC/N, respectively, which are all about 1.5 times larger than those of non-textured ceramics.