Effect of microelements addition on the interfacial reaction between Sn-Ag-Cu solders and the Cu substrate

Three kinds of Sn-Ag-based lead-free solders, Sn-3.5Ag-0.7Cu, Sn-3.5Ag-0.5Cu-0.07Ni-0.01Ge, and Sn-3.5Ag-0.07Ni (in wt.%), were selected to explore the effect of microelements (Ni and Ge) on the interfacial reaction between the solder and the Cu substrate. The thickness of the interfacial intermetallics formed with the Sn-3.5Ag-0.5Cu-0.07Ni-0.01Ge and Sn-3.5Ag-0.07Ni solders is several times that of the Sn-3.5Ag-0.7Cu solder. The added microelements converted the feature of interfacial intermetallics from pebble shape to worm shape. However, the results of x-ray diffraction (XRD) analysis suggest that the interfacial intermetallics formed with both solders have the same crystal structure. The results of energy dispersive spectroscopy (EDS) analysis show that the major interfacial intermetallic formed with the Sn-3.5Ag-0.7Cu solder is Cu₆Sn₅, while it is (Cu_x,Ni_1−x)₆Sn₅ with Sn-3.5Ag-0.5Cu-0.07Ni-0.01Ge. Ni influences the interfacial intermetallics and plays the influential role on the difference of interfacial reaction rate between liquid solder and solid Cu and the morphology of interfacial intermetallics. Additionally, the growth kinetics of the interfacial intermetallic compounds (IMCs) formed in the systems of Cu/Sn-3.5Ag-0.7Cu and Cu/Sn-3.5Ag-0.07Ni at high-temperature storage was also explored.     

Comparative study of interfacial reactions of Sn-Ag-Cu and Sn-Ag solders on Cu pads during reflow soldering

The interfacial reaction in soldering is a crucial subject for the solder-joint integrity and reliability in electronic packaging technology. However, electronic industries are moving toward lead-free alloys because of environmental concerns. This drive has highlighted the fact that the industry has not yet arrived at a decision for lead-free solders. Among the lead-free alloys, Sn-3.5Ag and Sn-3.5Ag-0.5Cu are the two potential candidates. Here, detailed microstructural studies were carried out to compare the interfacial reaction of Sn-3.5Ag and Sn-3.5Ag-0.5Cu solder with a ball grid array (BGA) Cu substrate for different reflow times. The Cu dissolution from the substrate was observed for different soldering temperatures ranging from 230°C to 250°C, and the dissolution was found to increase with time and temperature. Dissolution of Cu in the Sn-3.5Ag solder is so fast that, at 240°C, 12 μm of the Cu substrate is fully consumed within 5 min. Much less dissolution is observed for the Sn-3.5Ag-0.5Cu solder. In respect to such high dissolution, there is no significant difference observed in the intermetallic compound (IMC) thickness at the interface for both solder alloys. A simplistic theoretical approach is carried out to find out the amount of Cu₆Sn₅ IMCs in the bulk of the solder by the measurement of the Cu consumption from the substrate and the thickness of the IMCs that form on the interface.     

Reactions of lead-free solders with CuNi metallizations

We have done experimental research on the dissolution rate and intermetallic growth on Cu, Ni, and CuNi-alloy substrates as a function of time and Cu/Ni ratio of the substrate. Reactions that occur when CuNi metallizations are soldered with lead-free solders were investigated. The experiments were performed using Sn-3.5Ag and Sn-3.8Ag-0.7Cu solders and different CuNi alloys. To determine the rate of dissolution of the substrate material into the solder, CuNi foils of different concentrations were immersed in Sn-3.5Ag and Sn-3.8Ag-0.7Cu solder baths for soldering times ranging from 15 sec to 5 min at 250°C. In addition, reflows of solder balls were made on top of bulk substrates to study the reaction when there is a practically infinite amount of CuNi available compared to the amount of solder. Thin film experiments were also done, where Ni containing under bump metallizations (UBMs) were fabricated and reflowed with eutectic SnAg solder balls. The nickel slows down the dissolution of the UBM into the solder and the formation of intermetallics during reflow compared to Cu metallizations. The solder/UBM interfaces were analyzed with SEM to find out how Ni concentration affects the reaction, and how much Ni is needed to obtain a sufficiently slow reaction rate.     

Spreading Behavior and Evolution of IMCs During Reactive Wetting of SAC Solders on Smooth and Rough Copper Substrates

The effect of surface roughness of copper substrate on the reactive wetting of Sn-Ag-Cu solder alloys and morphology of intermetallic compounds (IMCs) was investigated. The spreading behavior of solder alloys on smooth and rough Cu substrates was categorized into capillary, diffusion/reaction, and contact angle stabilization zones. The increase in substrate surface roughness improved the wetting of solder alloys, being attributed to the presence of thick Cu₃Sn IMC at the interface. The morphology of IMCs transformed from long needle shaped to short protruded type with an increase in the substrate surface roughness for the Sn-0.3Ag-0.7Cu and Sn-3Ag-0.5Cu solder alloys. However, for the Sn-2.5Ag-0.5Cu solder alloy the needle-shaped IMCs transformed to the completely scallop type with increase in the substrate surface roughness. The effect of Ag content on wetting behavior was not significant.     

Investigation of Dissolution Behavior of Metallic Substrates and Intermetallic Compound in Molten Lead-free Solders

This study investigates the dissolution behavior of the metallic substrates Cu and Ag and the intermetallic compound (IMC)-Ag₃Sn in molten Sn, Sn-3.0Ag-0.5Cu, Sn-58Bi and Sn-9Zn (in wt.%) at 300, 270 and 240°C. The dissolution rates of both Cu and Ag in molten solder follow the order Sn > Sn-3.0Ag-0.5Cu >Sn-58Bi > Sn-9Zn. Planar Cu₃Sn and scalloped Cu₆Sn₅ phases in Cu/solders and the scalloped Ag₃Sn phase in Ag/solders are observed at the metallic substrate/solder interface. The dissolution mechanism is controlled by grain boundary diffusion. The planar Cu₅Zn₈ layer formed in the Sn-9Zn/Cu systems. AgZn₃, Ag5Zn₈ and AgZn phases are found in the Sn-9Zn/Ag system and the dissolution mechanism is controlled by lattice diffusion. Massive Ag₃Sn phases dissolved into the solders and formed during solidification processes in the Ag₃Sn/Sn or Sn-3.0Ag-0.5Cu systems. AgZn₃ and Ag₅Zn₈ phases are formed at the Sn-9Zn/Ag₃Sn interface. Zn atoms diffuse through Ag-Zn IMCs to form (Ag, Zn)Sn₄ and Sn-rich regions between Ag₅Zn₈ and Ag₃Sn.     

Interfacial reaction studies on lead (Pb)-free solder alloys

Recently, the research and development activities for replacing Pb-containing solders with Pb-free solders have been intensified due to both competitive market pressures and environmental issues. As a result of these activities, a few promising candidate solder alloys have been identified, mainly, Sn-based alloys. A key issue affecting the integrity and reliability of solder joints is the interfacial reactions between a molten solder and surface finishes in the solder joint structures. In this paper, a fundamental study of the interfacial reactions between several Pb-free candidate solders and surface finishes commonly used in printed-circuit cards is reported. The Pb-free solders investigated include Sn-3.5 Ag, Sn-3.8 Ag-0.7 Cu, and Sn-3.5 Ag-3.0 Bi. The surface finishes investigated include Cu, Au/Ni(P), Au/Pd/Ni(P), and Au/Ni (electroplated). The reaction kinetics of the dissolution of surface finishes and intermetallic compound growth have been measured as a function of reflow temperature and time. The intermetallic compounds formed during reflow reactions have been identified by SEM with energy dispersive x-ray spectroscopy.     

Morphology and growth kinetics of intermetallic compounds in solid-state interfacial reaction of electroless Ni-P with Sn-based lead-free solders

A comparative study of solid/solid interfacial reactions of electroless Ni-P (15 at.% P) with lead-free solders, Sn-0.7Cu, Sn-3.5Ag, Sn-3.8Ag-0.7Cu, and pure Sn, was carried out by performing thermal aging at 150°C up to 1000 h. For pure Sn and Sn-3.5Ag solder, three distinctive layers, Ni₃Sn₄, SnNiP, and Ni₃P, were observed in between the solder and electroless Ni-P; while for Sn-0.7Cu and Sn-3.8Ag-0.7Cu solders, two distinctive layers, (CuNi)₆Sn₅ and Ni₃P, were observed. The differences in morphology and growth kinetics of the intermetallic compounds (IMCs) at the interfaces between electroless Ni-P and lead-free solders were investigated, as well as the growth kinetics of the P-enriched layers underneath the interfacial IMC layers. With increasing aging time, the coarsening of interfacial Ni₃Sn₄ IMC grains for pure Sn and Sn-3.5Ag solder was significantly greater than that of the interfacial (CuNi)₆Sn₅ IMC grains for Sn-0.7Cu and Sn-3.8Ag-0.7Cu solders. Furthermore, the Ni content in interfacial (CuNi)₆Sn₅ phase slightly increased during aging. A small addition of Cu (0.7 wt.%) resulted in differences in the type, morphology, and growth kinetics of interfacial IMCs. By comparing the metallurgical aspects and growth kinetics of the interfacial IMCs and the underneath P-enriched layers, the role of initial Cu and Ag in lead-free solders is better understood.     

Low-cycle fatigue behavior of Sn-Ag, Sn-Ag-Cu, and Sn-Ag-Cu-Bi lead-free solders

Low-cycle fatigue (LCF) tests on as-cast Sn-3.5Ag, Sn-3Ag-0.5Cu, Sn-3Ag-0.5Cu-1Bi, and Sn-3Ag-0.5Cu-3Bi solders was carried out using a noncontact strain-controlled system at 20°C with a constant frequency of 0.1 Hz. The addition of Cu does not significantly affect the fatigue life of eutectic Sn-Ag solder. However, the fatigue life was significantly reduced with the addition of Bi. The LCF behavior of all solders followed the Coffin-Manson relationship. The fatigue life of the present solders is dominated by the fracture ductility and can be described by the ductility-modified Coffin-Manson’s relationship. Steps at the boundaries of dendrite phases were the initiation sites for microcracks for Sn-3.5Ag, Sn-3Ag-0.5Cu, and Sn-3Ag-0.5Cu-1Bi solders, while for Sn-3Ag-0.5Cu-3Bi solder, cracks initiated along both the dendrite boundaries and subgrain boundaries in the dendrite phases. The linking of these cracks and the propagation of cracks inside the specimen occurred both transgranularly through eutectic phases and intergranularly along dendrite boundaries or subgrain boundaries.     

Intermetallic growth kinetics for Sn-Ag, Sn-Cu, and Sn-Ag-Cu lead-free solders on Cu, Ni, and Fe-42Ni substrates

Soldering with the lead-free tin-base alloys requires substantially higher temperatures (∼235–250°C) than those (213–223°C) required for the current tin-lead solders, and the rates for intermetallic compound (IMC) growth and substrate dissolution are known to be significantly greater for these alloys. In this study, the IMC growth kinetics for Sn-3.7Ag, Sn-0.7Cu, and Sn-3.8Ag-0.7Cu solders on Cu substrates and for Sn-3.8Ag-0.7Cu solder with three different substrates (Cu, Ni, and Fe-42Ni) are investigated. For all three solders on Cu, a thick scalloped layer of η phase (Cu₆Sn₅) and a thin layer of ε phase (Cu₃Sn) were observed to form, with the growth of the layers being fastest for the Sn-3.8Ag-0.7Cu alloy and slowest for the Sn-3.7Ag alloy. For the Sn-3.8Ag-0.7Cu solder on Ni, only a relatively uniform thick layer of η phase (Cu,Ni)₆Sn₅ growing faster than that on the Cu substrate was found to form. IMC growth in both cases appears to be controlled by grain-boundary diffusion through the IMC layer. For the Fe-42Ni substrate with the Sn-3.8Ag-0.7Cu, only a very thin layer of (Fe,Ni)Sn₂ was observed to develop.     

Morphology and Growth of Intermetallics at the Interface of Sn-based Solders and Cu with Different Surface Finishes

Several types of surface finishes have been applied on Cu substrates in an effort to facilitate bonding and improve the reliability of lead-free solder joints. In the current research, the effects of printed circuit board surface finishes on the reliability of the solder joints were investigated by examining the morphology and growth behavior of the intermetallic compounds (IMCs) between Sn-based solders and different surface finishes on Cu. Three types of Cu substrates with different surface finishes were fabricated in this study: organic solderability preservative (OSP)/Cu, Ni/Cu, and electroless nickel immersion gold (ENIG)/Cu. Sn-3.5Ag and Sn-3.0Ag-0.5Cu were used as the solders. In the experiment, the solder joint specimens were aged isothermally at 150°C for up to 1000 h. Experimental results revealed that the OSP surface finish promoted the interdiffusion between Cu and Sn during soldering. The composition and morphology of the IMC layer at the solder/Ni/Cu interface were sensitive to the Cu concentration in the solder. Meanwhile, the solder joints with different morphological features of the IMCs exhibited significant differences in shear strengths. The Au-containing ENIG surface finish affected the shear strength of the solder joint significantly at the initial stage of isothermal aging.     

Wetting and reaction of Sn-2.8Ag-0.5Cu-1.0Bi solder with Cu and Ni substrates

The wettability of newly developed Sn-2.8Ag-0.5Cu-1.0Bi lead-free solder on Cu and Ni substrates was assessed through the wetting balance tests. The wettability assessment parameters such as contact angle (ϑ_c) and maximum wetting force (F_w) were documented for three solder bath temperatures with three commercial fluxes, namely, no-clean (NC), nonactivated (R), and water-soluble organic acid flux (WS). It was found that the lead-free Sn-2.8Ag-0.5Cu-1.0Bi solder exhibited less wetting force, i.e., poorer wettability, than the conventional Sn-37Pb solder for all flux types and solder bath temperatures. The wettability of Sn-2.8Ag-0.5Cu-1.0Bi lead-free solder on Cu substrate was much higher than that on Ni substrate. Nonwetting for Sn-2.8Ag-0.5Cu-1.0Bi and Sn-Pb solders on Ni substrate occurred when R-type flux was used. A model was built and simulations were performed for the wetting balance test. The simulation results were found very close to the experimental results. It was also observed that larger values of immersion depth resulted in a decrease of the wetting force and corresponding meniscus height, whereas the increase in substrate perimeter enhanced the wettability. The wetting reactions between the solder and Cu/Ni substrates were also investigated, and it was found that Cu atoms diffused into the solder through the intermetallic compounds (IMCs) much faster than did the Ni atoms. Rapid formation of IMCs inhibited the wettability of Sn-2.8Ag-0.5Cu-1.0Bi solder compared to the Sn-Pb solder.     

Ball Impact Responses of Ni- or Ge-Doped Sn-Ag-Cu Solder Joints

In this work, we present ball impact test (BIT) responses and fractographies obtained at an impact velocity of 500 mm/s on Sn-4Ag-0.5Cu, Sn-1Ag-0.5Cu, Sn-1Ag-0.5Cu-0.05Ni, Sn-1.2Ag-0.5Cu-0.05Ni, and Sn-1Ag-0.5Cu-0.05Ge package-level solder joints. The solder joints are bonded on substrate pads of either immersion tin (IT) or direct solder on pad (DSOP) surface finishes. Differences of BIT results with respect to multi-reflow are also reported. Taking the impact energy as an indication of board-level drop reliability of the solder joints, the BIT results indicate that better reliability can be achieved by adopting Sn-Ag-Cu solder alloys with low Ag weight contents as well as IT substrate pad finish rather than DSOP. Moreover, the addition of Ni or Ge to the solder alloy provides a large improvement; Ni alters the interfacial intermetallic compound (IMC) structure while Ge enhances the mechanical behavior of the bulk solder.     

Studies of the mechanical and electrical properties of lead-free solder joints

The mechanical and electrical properties of several Pb-free solder joints have been investigated including the interfacial reactions, namely, the thickness and morphology of the intermetallic layers, which are correlated with the shear strength of the solder joint as well as its electrical resistance. A model joint was made by joining two “L-shaped” copper coupons with three Pb-free solders, Sn-3.5Ag (SA), Sn-3.8Ag-0.7Cu (SAC), and Sn-3.5Ag-3Bi (SAB) (all in wt.%), and combined with two surface finishes, Cu and Ni(P)/Au. The thickness and morphology of the intermetallic compounds (IMCs) formed at the interface were affected by solder composition, solder volume, and surface finish. The mechanical and electrical properties of Pb-free solder joints were evaluated and correlated with their interfacial reactions. The microstructure of the solder joints was also investigated to understand the electrical and mechanical characteristics of the Pb-free solder joints.     

Fatigue crack-growth behavior of Sn-Ag-Cu and Sn-Ag-Cu-Bi lead-free solders

Fatigue crack-growth behavior and mechanical properties of Sn-3Ag-0.5Cu, Sn-3Ag-0.5Cu-1Bi, and Sn-3Ag-0.5Cu-3Bi solders have been investigated at room temperature (20°C). The tensile strength and hardness of the solders increased with increasing Bi content. However, the yield strengths of Sn-3Ag-0.5Cu-1Bi and Sn-3Ag-0.5Cu-3Bi solders were nearly similar, but the 3Bi solder exhibited the lowest ductility. Fatigue crack-growth behavior of the solders was dominantly cycle dependent in the range of stress ratios from 0.1–0.7 at a frequency of 10 Hz, except for the Sn-3Ag-0.5Cu solder tested at a stress ratio of 0.7. Mixed intergranular/transgranular crack propagation was observed for the Sn-3Ag-0.5Cu solder tested at the stress ratio of 0.7, indicating the importance of creep in crack growth. The Sn-3Ag-0.5Cu-1Bi and Sn-3Ag-0.5Cu-3Bi solders had higher resistance to time-dependent crack growth, resulting from the strengthening effect of the Bi constituent. It appears that the addition of Bi above a certain concentration is harmful to the mechanical properties of Sn-3Ag-0.5Cu.     

Mechanical strength of Sn-3.5Ag-based solders and related bondings

The tensile strengths of bulk solders and joint couples of Sn-3.5Ag-0.5Cu, Sn-3.5Ag-0.07Ni, and Sn-3.5Ag-0.5Cu-0.07Ni-0.01Ge solders and the shear strengths of ball grid array (BGA) specimens, solder-ball-attached Cu/Ni/Au metallized substrates were investigated. The tensile strength of the bulk is degraded by thermal aging. The Ni-containing solder exhibits lower tensile strength than Sn-3.5Ag-0.5Cu after thermal aging. However, the Ni-containing solder joints show greater tensile strength than the Cu/Sn-3.5Ag-0.5Cu/Cu joint. Fracture of the solder joint occurs between the intermetallic compound (IMC) and the solder. The shear strength and fracture mechanism of BGA specimens are the same regardless of solder composition.     

Reaction of Liquid Sn-Ag-Cu-Ce Solders with Solid Copper

Small amounts of the rare-earth element Ce were added to the Sn-rich lead-free eutectic solders Sn-3.5Ag-0.7Cu, Sn-0.7Cu, and Sn-3.5Ag to improve their properties. The microstructures of the solders without Ce and with different amounts (0.1 wt.%, 0.2 wt.%, and 0.5 wt.%) of Ce were compared. The microstructure of the solders became finer with increasing Ce content. Deviation from this rule was observed for the Sn-Ag-Cu solder with 0.2 wt.% Ce, and for the Sn-0.7Cu eutectic alloy, which showed the finest microstructure without Ce. The melting temperatures of the solders were not affected. The morphology of intermetallic compounds (IMC) formed at the interface between the liquid solders and a Cu substrate at temperatures about 40°C above the melting point of the solder for dipping times from 2 s to 256 s was studied for the basic solder and for solder with 0.5 wt.% Ce addition. The morphology of the Cu₆Sn₅ IMC layer developed at the interface between the solders and the substrate exhibited the typical scallop-type shape without significant difference between solders with and without Ce for the shortest dipping time. Addition of Ce decreased the thickness of the Cu₆Sn₅ IMC layer only at the Cu/Sn-Ag-Cu solder interface for the 2-s dipping. A different morphology of the IMC layer was observed for the 256-s dipping time: The layers were less continuous and exhibited a broken relief. Massive scallops were not observed. For longer dipping times, Cu₃Sn IMC layers located near the Cu substrate were also observed.     

Microstructure and Creep Deformation of Sn-Ag-Cu-Bi/Cu Solder Joints

Sn-Ag-Cu solder is one of the candidate alternatives to Sn-Pb-based solders. In order to improve its performance, different materials have been added to Sn-Ag-Cu-based solders. Several studies on Sn-Ag-Cu-based solders with Bi additions have shown Sn-Ag-Cu-Bi to be a class of solders with good wetting behavior and good performance that show great promise for use in the electronics assembly and packaging industry. To investigate the mechanical reliability of the Sn-Ag-Cu-Bi solders further, single-lap shear creep characteristics have been studied in this work. Dog-bone-type solder joint specimens were formed using five types of solder alloys, Sn-3.0Ag-0.5Cu and Sn-3.0 Ag-0.5Cu-xBi (x = 1 wt.% to 4 wt.%) with Cu substrates, and creep tests were performed at temperatures of 120°C and 150°C under stresses of 5 MPa to 10 MPa. Results indicate that the rupture times for Sn-3.0Ag-0.5Cu-xBi solder joints up to 4 wt.% of Bi are longer than the rupture time for Sn-3.0Ag-0.5Cu. Stress exponents ranged from 3 to 7 for temperatures of 150°C and 120°C with stresses under 10 MPa. Microstructural analyses using scanning electron microscopy (SEM) were performed and related to the creep behavior of the solder joints.     

Sn基钎料与Cu和Al基板的润湿性比较研究

采用润湿平衡法测量了四种Sn基钎料(Sn-37Pb、Sn-3.OAg-0.5Cu、Sn-0.7Cu与Sn-9Zn)分别在250,260和270℃与Cu、Al两种基板的润湿性能.结果表明:钎料与Al基板的润湿时间均比Cu基板长,除Sn-9Zn外,其他三种钎料与Cu基板的润湿力比Al基板大,并且随着温度升高,润湿性能提高,...     

Interfacial microstructure and bonding strength of Sn-3Ag-0.5Cu and Sn-3Ag-0.5Cu-0.5Ce-xZn solder BGA packages with immersion Ag surface finish

Although it has been verified that tin whiskers can be prevented by the addition of 0.5 wt.% Zn into a Sn-3Ag-0.5Cu-0.5Ce solder, no detailed studies have been conducted on interfacial reactions and mechanical properties of Sn-3Ag-0.5Cu-0.5Ce-xZn solder joints with an immersion Ag surface finish. The intermetallic compounds formed during the reflow and aging of Sn-3Ag-0.5Cu and Sn-3Ag-0.5Cu-0.5Ce-xZn solder ball grid array (BGA) packages were investigated. Because more heterogeneous nucleation sites, provided by CeSn₃ intermetallics and Zn atoms, formed in the Sn-3Ag-0.5Cu-0.5Ce-xZn solder matrix, and Cu and Zn have a stronger affinity than Cu and Sn, the Cu-Sn intermetallics growth in Sn-3Ag-0.5Cu-0.5Ce-xZn solder joints with Ag/Cu pads was suppressed. The 0.2% Zn addition for inhibiting rapid whisker growth in RE-doped Sn-Ag-Cu solder joints is more appropriate than 0.5 wt.% additions, as excess Zn addition causes poor oxidation resistance and inferior bonding strength.     

Effects of Metallic Nanoparticles on Interfacial Intermetallic Compounds in Tin-Based Solders for Microelectronic Packaging

Tin (Sn)-based solders have established themselves as the main alternative to the traditional lead (Pb)-based solders in many applications. However, the reliability of the Sn-based solders continues to be a concern. In order to make Sn-based solders microstructurally more stable and hence more reliable, researchers are showing great interest in investigating the effects of the incorporation of different nanoparticles into them. This paper gives an overview of the influence of metallic nanoparticles on the characteristics of interfacial intermetallic compounds (IMCs) in Sn-based solder joints on copper substrates during reflow and thermal aging. Nanocomposite solders were prepared by mechanically blending nanoparticles of nickel (Ni), cobalt (Co), zinc (Zn), molybdenum (Mo), manganese (Mn) and titanium (Ti) with Sn-3.8Ag-0.7Cu and Sn-3.5Ag solder pastes. The composite solders were then reflowed and their wetting characteristics and interfacial microstructural evolution were investigated. Through the paste mixing route, Ni, Co, Zn and Mo nanoparticles alter the morphology and thickness of the IMCs in beneficial ways for the performance of solder joints. The thickness of Cu₃Sn IMC is decreased with the addition of Ni, Co and Zn nanoparticles. The thickness of total IMC layer is decreased with the addition of Zn and Mo nanoparticles in the solder. The metallic nanoparticles can be divided into two groups. Ni, Co, and Zn nanoparticles undergo reactive dissolution during solder reflow, causing in situ alloying and therefore offering an alternative route of alloy additions to solders. Mo nanoparticles remain intact during reflow and impart their influence as discrete particles. Mechanisms of interactions between different types of metallic nanoparticles and solder are discussed.