共查询到20条相似文献,搜索用时 156 毫秒
1.
2.
烧重油的镇海联合循环电站据“GasTurbineWorld”1997年7-8月号报道,浙江镇海328MW联合循环电站为达到最低的电力生产成本,被设计成烧“桶底”重油,这些重油经彻底处理,以便给出相当好的燃气轮机使用寿命。该电站被设计成基本负荷运行,在... 相似文献
3.
4.
燃气轮机重油处理系统方案研究 总被引:1,自引:0,他引:1
随着世界经济的发展,对石油资源的消耗也越来越多,为更充分利用有限的石油资源,重油逐渐被应用于电力生产,而发电用燃气轮机以重油作为燃料,可有效地降低运行成本,因此,重油的处理问题颇受重视。本文简要说明了燃气轮机燃用重油技术的一些特点,及燃用前重油的一些处理方法,特别针对重油的超临界水处理方法,设计了一个完整的处理系统,以除去重油中的钒元素,并对两种不同的超临界水—重油混合器结构进行了混合过程的数值分析,选取了一种较好的结构用于该处理系统,为更进一步将超临界水处理技术应用于燃气轮机燃用重油的系统中奠定了基础。 相似文献
5.
浙江镇海的300MW燃气—蒸汽联合联合循环电站由两台100MW的MS9001E燃气轮发电机组、一台100MW蒸汽轮发电机组及两台无补燃余热锅炉组成。燃气轮机由美国GE公司提供,机组起停机时用0#柴油,正常运行时燃用180cSt重油。其中#8燃气轮机(到性能改造前总运行时间37 290·5小时、启动8 相似文献
6.
对联合循环电站燃气轮机选型、蒸汽系统的选择、余热锅炉和汽轮机选型、机组轴系配置、动力岛布置、主要辅助设备的选择等方面进行了分析研究,为联合循环电站的设计和研究方向提供了建议。 相似文献
7.
8.
燃气轮机燃用重油是解决燃气轮机燃料短缺的途径之一,由于轻油的价格高,机组大多数用来调峰,使用率低,因此燃机改烧价格低的重油意义是重大的。美国Petrolite公司是世界上主要提供燃气轮机燃用重质油的处理技术的公司,该公司所研制及应用的设备和添加剂制品使得燃气轮机能成功地燃用重油和其他非精炼油,目前世界上均使用这种技术。本文主要介绍Petrolite公司的重油处理技术及有关内容,供读者参考。 相似文献
9.
针对国内某6FA燃气轮机试车台的排气系统进行性能研究,阐述了燃气轮机试车台排气系统的作用、组成、性能和潜在问题等。通过声学和热力学分析,重点讨论了6FA燃气轮机试车台排气系统的噪声、保温性能,并对未来运行过程中可能出现的问题进行探讨。试车台用燃气轮机排气系统与电站用燃气轮机排气系统有很大区别,给同类型燃气轮机试车台的排气系统搭建提供参考。 相似文献
10.
论述了IGCC电站产生NOx的原因及其应对措施,重点探讨了注氮脱硝方式对电站系统的影响。结果表明,采用注氮脱硝前,相关的经济性比较至关重要,需考虑压气机、燃气轮机透平的匹配问题及气化炉的氮气用量。结论为今后IGCC电站脱硝系统的设计提供依据和参考。 相似文献
11.
12.
13.
重油以60%左右轻油价格的优势吸引众多的燃机电厂考虑燃用重油。但已建轻油机组如何改造?烧重油到底能带来多大的经济效益。本文介绍与分析了机组重油改造以及重油试运行的基本情况。 相似文献
14.
[目的]随着城市的发展,电厂逐步由"外"向"内"发生变化,单一的建筑设计已无法满足处于城市中的电厂设计,以黄埔电厂为例,为同类型——城市型燃机电厂设计提供借鉴.[方法]通过分析、整合、利用,使多种不利因素转变为电厂去工业化的元素,丰富去工业化设计的内涵.[结果]文章分析了黄埔电厂在土地利用、建筑表皮、降噪和景观绿化等方... 相似文献
15.
就1台GT13E2型燃气轮机发生的一起燃烧室及排气烟道爆炸事故进行了详细的分析,认为在控制油压力消失和燃烧室熄火的情况下,燃气轮机仍然不能发出跳机指令,进而在燃气轮机转速下降过程中发电机低频保护动作断开主变高压侧断路器,造成厂用电丢失,导致燃气轮机在燃油系统的事故水冲洗过程中发生爆炸。指出了爆炸的原因是由于制造厂燃气轮机控制系统逻辑及控制油管道设计错误,爆炸是设计错误发展的必然结果,以及事故处理和预防措施。 相似文献
16.
17.
Jong Jun Lee Young Sik Kim Kyu Sang Cha Tong Seop Kim Jeong L. Sohn Yong Jin Joo 《Applied Energy》2009
An IGCC (integrated gasification combined cycle) plant consists of a power block and a gasifier block, and a smooth integration of these two parts is important. This work has analyzed the influences of the major design options on the performance of an IGCC plant. These options include the method of integrating a gas turbine with an air separation unit and the degree of nitrogen supply from the ASU to the gas turbine combustor. Research focus was given to the effect of each option on the gas turbine operating condition along with plant performance. Initially, an analysis adopting an existing gas turbine without any modifications of its components was performed to examine the influence of two design options on the operability of the gas turbine and performance of the entire IGCC plant. It is shown that a high integration degree, where much of the air required at the air separation unit is supplied by the gas turbine compressor, can be a better option considering both the system performance and operation limitation of the gas turbine. The nitrogen supply enhances system performance, but a high supply ratio can only be acceptable in high integration degree designs. Secondly, the modifications of gas turbine components to resume the operating surge margin, such as increasing the maximum compressor pressure ratio by adding a couple of stages and increasing turbine swallowing capacity, were simulated and their effects on system performance were examined. Modification can be a good option when a low integration degree is to be adopted, as it provides a considerable power increase. 相似文献
18.
北京燕山石化公司烟机运行分析及改进措施 总被引:1,自引:0,他引:1
分别介绍了中国石化北京燕山分公司炼油厂2000kt/a重油催化裂化装置和800kt/a催化裂化装置配套的烟机发电机组更新改造及运行分析情况,提出了优化装置反再系统的工艺控制、严格控制烟气催化剂浓度等措施以保证烟机发电机组长周期运行。 相似文献
19.
20.
《Energy》2004,29(8):1183-1205
This paper presents the engineering design and theoretical exergetic analyses of the plant for combustion gas turbine based power generation systems. Exergy analysis is performed based on the first and second laws of thermodynamics for power generation systems. The results show the exergy analyses for a steam cycle system predict the plant efficiency more precisely. The plant efficiency for partial load operation is lower than full load operation. Increasing the pinch points will decrease the combined cycle plant efficiency. The engineering design is based on inlet air-cooling and natural gas preheating for increasing the net power output and efficiency. To evaluate the energy utilization, one combined cycle unit and one cogeneration system, consisting of gas turbine generators, heat recovery steam generators, one steam turbine generator with steam extracted for process have been analyzed. The analytical results are used for engineering design and component selection. 相似文献