新型交叉耦合双模宽带带通滤波器设计

采用变形的阶梯阻抗谐振器(SIR)设计了一款小型化、高性能新型宽带带通滤波器.通过对经典的SIR进行弯折,在高阻抗线之间引入交叉耦合构成交叉耦合多模谐振器.该谐振器具有与经典SIR相同的谐振模式,由前两个谐振模式构成通带,并且在上下阻带产生两对对称的传输零点.该带通滤波器结构紧凑、带内差损非常小,同时由于带外传输零点的存在,一阶杂散得到有效抑制,带外特性明显改善.     

基于阶梯阻抗谐振器的双频微带带通滤波器设计

设计了一种基于1/4波长阶梯阻抗谐振器(SIR)的交叉耦合微带双频带通滤波器,利用SIR终端加载的金属化短路通孔实现K倒置器,利用谐振器之间的级间耦合实现J倒置器,通过相邻谐振器之间的级联耦合和不相邻谐振器之间的交叉耦合,完成了四阶双频带通滤波器的设计。滤波器两个通带的中心频率分别为3.78GHz和8.69GHz,中心频率比大于2,对应的插入损耗分别为-1.28dB和-2.29dB,带内回波损耗分别为-12.38dB和-25.0dB。测量结果和仿真结果基本吻合,实现了双频带通滤波器的小型化和低损耗。     

慢波结构SIR双频带通滤波器设计

本文通过分析阶梯阻抗谐振器（SIR）和慢波结构谐振器的特性,提出了利用SIR谐振器的寄生通带产生第二通带的双频带通滤波器设计方法,以达到滤波器小型化的目的;并基于0°馈电结构获取传输零点的原理对滤波器阻带性能进行优化。最后结合ADS仿真软件设计了一个中心频率在2.4GHz和5.2GHz的微带双频带通滤波器。仿真结果表明滤波器具有良好的带内带外特性。本文所设计的滤波器尺寸小,性能好,具有很好的实用价值。     

基于阶梯阻抗的发夹结构低通滤波器设计

提出一种基于阶梯阻抗发夹谐振器的小型化微波低通滤波嚣,该滤波嚣仅由包含四节微带的阶梯阻抗发夹谐振器构成.设计结果表明,滤波器3dB通带从直流到2.8G,带内反射小于-20dB,带外抑制达到40dB.这种滤波器尺寸小,易制造,且具有陡峭的截止频率响应特性,可用于许多微波系统中.     

基于多层技术双通带Chebyshev滤波器综合设计

为了提高滤波器的选择性,实现小型化,采用多层板技术综合方法设计了一款双通带Chebyshev响应带通滤波器.利用组成上通带的半波长开环谐振器的空间交叉耦合引入两个有限频率传输零点,以提高滤波器频率选择性.同时,利用组成下通带的四分之一波长短路谐振器形成零度馈电混合耦合结构,生成另外两个传输零点,不但提高了通带隔离度,而...     

应用于多模WLANs的紧凑SIR双频带通滤波器

提出了一种基于阶梯阻抗谐振器的紧凑、高选择性的微带双频带通滤波器,使用了两个发卡型阶梯阻抗谐振器交叉组成了伪交指结构谐振器,实现了小型化双频滤波器。采用0°馈电结构引入了三个传输零点,从而提高了频率选择特性。加工了微带双频带通滤波器实物,实测结果显示,两个通带中心频率分别为2.41GHz和5.26GHz,中心频率比大于2,带内插损分别为1.06dB和1.59dB,3dB相对带宽分别为22.8%、15.6%,仿真与实测吻合较好。与传统的分支加载、阶梯阻抗等双频滤波器相比,该滤波器具有设计简单、结构紧凑、低插入损耗及高频率选择特性等优点。     

双频带通滤波器的优化设计

利用阶跃阻抗谐振器优化,设计了一个工作在无线局域网(2.4/5.2GHz)的双频带通滤波器。通过奇、偶模分析,在阶跃阻抗谐振器理论计算公式基础上,根据不同的阻抗比条件,阶跃阻抗谐振器谐振频率比与阶跃阻抗高、低阻抗电长度之比的关系曲线,可以方便地确定阶跃阻抗谐振器的谐振频率和电长度,通过sonnet电路仿真软件验证了设计的合理性,并给出了用于无线通信2.4、5.2 GHz双频带通滤波器的设计结果。该带通滤波器可以分别在2.4、5.2 GHz处得到较好的通带性。由于交叉耦合的存在,该双频带通滤波器在两个通带端各有一个传输零点,以此来提高滤波器的通带频率选择性。最后,测量结果与仿真结果基本吻合。     

LTCC 阶梯阻抗谐振器带通滤波器的设计

结合阶梯阻抗谐振器的设计方法, 设计了一款基于低温共烧陶瓷(LTCC)工艺的阶梯阻抗谐振器带通滤波器。所设计带通滤波器除了顶部、底部接地板,中间共有三层结构, 各个相邻的谐振器之间进行宽边耦合。该带通滤波器有两个谐振腔, 中心频率约为10 GHz, 通带范围为8.9 GHz 到11.7 GHz。该带通滤波器有效地减小了体积, 总体积为3.2 mm×1.6 mm×1.7 mm。     

基于枝节加载谐振器的新型三频带通滤波器设计

提出了一种新型平面三频带通滤波器,该滤波器由一个加载短路枝节的阶梯阻抗谐振器,一对加载开路枝节的背靠背E型谐振器,以及包含源负载直接耦合的馈电结构组成.所采用的枝节加载谐振器的多模工作特性使滤波器的体积大大减小,同时每个通带的位置及其耦合特性都能够独立调谐.另外,通过源负载直接耦合引入通带两侧的传输零点,实现了滤波器良好的频率选择性.最后设计并加工了一款高选择性小型化三频带通滤波器,其三个通带的中心频率分别为2.0GHz,3.95GHz和6.35GHz,插入损耗均小于2.5dB,带内回波损耗均优于14dB,实验结果与仿真结果吻合良好.     

阶跃阻抗谐振器及三阶交叉耦合带通滤波器设计

本文首先分析了三阶阶跃阻抗谐振器的谐振特性。然后用这样的谐振器单元组合构成三阶交叉耦合带通滤波器,该滤波器能在通带的高端产生一个传输零点,提高阻带的抑制效果。仿真结果与设计指标基本吻合,证明了设计的正确性。     

Design of quasi-elliptic function filters with a dual-passband response

Compact miniaturized hairpin resonators are used to design cross-coupled filters with a dual-passband response of elliptic function type. The hairpin resonators are treated as a stepped impedance resonator (SIR) in analysis. In a filter, two different hairpin resonators are used to establish proper couplings required for the two design frequencies. Two filters are fabricated and measured. The results show a good agreement with the simulation.     

X波段SICL小型化带通滤波器的设计

为有效减小X波段滤波器的尺寸,减小通带损耗,对基片集成同轴线(SICL)结构进行了研究,提出一种阶跃阻抗(SIR)型SICL带通滤波器,并针对SICL谐振腔与其他平面电路的连接设计了一种由共面波导(CPW)向SICL谐振腔提供激励的平面结构,以便滤波器的测量。仿真结果表明,滤波器通带特性优异,其中心频率为10 GHz,带宽为1.5 GHz,尺寸为13 mm×7 mm,插入损耗为-0.8 dB。     

Ultra wideband filter using dumbbell-etched stepped impedance resonator

In this article, an ultra wideband bandpass filter using the dumbbell-etched stepped impedance resonator (SIR) is presented. The filter consists of a dumbbell-etched SIR with an impedance ratio K?>?1 and the enhanced coupled input/output lines. The SIR is folded into a dumbbell shape to achieve a smaller circuit size than the filter with conventional SIR. The bandwidth can be analysed using the image-parameter method to obtain the proper dimension of the coupled lines and verified using electromagnetic simulation. The measured 3?dB fractional bandwidth of 110% and insertion loss |S ₂₁| less than 3?dB over the entire passband are achieved.     

60 GHz compact integrated cross-coupled SIR-MH bandpass filter on bulk CMOS

A new 60 GHz fourth-order cross-coupled bandpass filter using a step- impedance-resonator (SIR) miniaturised open-loop resonator and the miniaturised-hairpin (MH) resonator was designed and fabricated on 0.13 mum bulk CMOS. It has 8.5 GHz (58-66.5 GHz) bandwidth, 5.9 dB insertion loss, and better than 10 dB return loss over the whole passband, and exhibits high selectivity and a compact size of 714.9 times 484 mum (0.346 mm ). This filter is the first reported cross-coupled filter above 40 GHz on CMOS.     

一种基于SIR结构的三通带带通滤波器

应用双指耦合结构和枝节加载谐振器（Stub-loaded Resonator,SLR）实现了一款基于阶梯阻抗谐振器（Stepped Impedance Resonator,SIR）的滤波器。该滤波器具有3个通带,带外抑制较好,工作频段提高。通过调整阻抗比可调节第二、三通带的谐振频率;SLR结构能够增加通带数量;SLR结构和双指耦合结构均能改善滤波器的S参数。HFSS软件仿真表明,3个通带的中心频率分别为3.5 GHz、6.6 GHz、9.2 GHz,对应的分数带宽分别为5.7%、3%、2%,S11分别为-18 dB、-22 dB、-24 dB,通带内的S21分别为-1.8 dB、-1 dB、-1 dB。电路的测量结果与仿真结果较为吻合。该滤波器在5G通信的低频段具有应用前景。     

Compact Dual-Band Filter Using Defected Stepped Impedance Resonator

This letter presents a novel approach for designing a dual-band bandpass filter by using defected stepped impedance resonator (DSIR). The resonant frequency of the DSIR is found to be much lower than that of the conventional microstrip stepped impedance resonator (SIR), which reduces the circuit size effectively. Two types of second-order DSIR microstrip bandpass filter operating at 1.85 and 2.35 GHz, respectively, are well designed according to the classical theory of coupled resonator filter. Then they are combined to construct a compact dual-band filter with a common parallel microstrip feed line, the measurement results of the fabricated filter have a good agreement with the simulation.     

An EM Tuning Procedure for Planar Filters Based on Individual Resonator Decomposition

Planar filters directly implemented by design formulas yield a distorted frequency response, especially at higher frequencies, due to dispersion and discontinuities. In this letter, an electromagnetic (EM) tuning procedure based on individual resonator decomposition for a fifth order stepped impedance resonator (SIR) filter is presented. The EM simulation of the SIR filter composed by the tuned resonators shows remarkable agreement with the design formula and requires no further tuning. The procedure is experimentally verified by comparing the measured and the simulation results.     

基于阶梯阻抗发夹谐振器的小型低通滤波器

提出一种基于阶梯阻抗发夹谐振器的小型化微波低通滤波器,该滤波器仅由包含一节微带线的阶梯阻抗发夹谐振器构成。设计结果表明,滤波器3dB通带从DC(Direct Current)到2GHz,回波损耗优于10dB,且插入损耗从DC到1.7GHz时优于0.5dB,带外抑制从2.9～4GHz优于20dB。仿真结果和实验结果吻合良好。这种滤波器尺寸小,易制造,且具有陡峭的截止频率响应特性,可应用于许多微波系统中。     

Design of Compact Tri-Band Bandpass Filters Using Assembled Resonators

A novel approach for designing tri-band bandpass filters with independently controllable center frequencies and improved stopband rejection characteristic is presented in this paper. The assembled resonator constructed by a stepped impedance resonator and a common half-wavelength resonator is employed to obtain tri-band response. The stepped impedance resonator is designed to operate at the first and third passbands and the other resonator is designed to operate at the second passband. Two kinds of filter configurations with cascaded and pseudointerdigital formats are proposed. Based on lossless lumped-element equivalent circuit, it is found that both filter structures can introduce transmission zeros between passbands. To verify the proposed approach, two filters are designed and fabricated, the measured results exhibit tri-band bandpass responses with high selectivity.