Cr2O3 doping in ZnO–0.5 mol% V2O5 varistor ceramics

The effects of the amount of Cr₂O₃ (0.5–4 mol%) on the microstructure and the electrical properties have been studied in a binary ZnO–0.5 mol% V₂O₅ system. The microstructure of the samples consists mainly of ZnO grains with ZnCr₂O₄ and α-Zn₃(VO₄)₂ as the minority secondary phases. The addition of Cr₂O₃ is found to be effective in controlling the abnormal ZnO grain growth often found in V₂O₅-doped ZnO ceramic system, and a more uniform microstructure can be obtained. The varistor performance is also improved as observed from the increase in the non-linear coefficient α of the Cr₂O₃-doped ZnO–V₂O₅ samples. The α value is found to increase with the amount of Cr₂O₃ for up to 3 mol% Cr₂O₃ content. Further increase in Cr₂O₃ is found to cause a decrease in the α value. The highest α value of 28.9 is obtained for the ZnO–0.5 mol% V₂O₅–3 mol% Cr₂O₃ sample.     

Study of color change and microstructure development of Al2O3–Cr2O3/Cr3C2 nanocomposites prepared by spark plasma sintering

The densification behaviors of Al₂O₃–Cr₂O₃/Cr₃C₂ nanocomposites prepared by a Spark Plasma Sintering (SPS) were investigated in this work. The initial powders used for sintering were Al₂O₃–Cr₂O₃, which were prepared by metal organic chemical vapor deposition (MOCVD) in a spout bed. Different colors of the compacts such as green, purple and black were observed after densification process at different SPS temperatures from 1200 °C to 1350 °C. These changes of color were relevant to the existence of secondary phase of green Cr₂O₃, pink solid solution of Cr₂O₃–Al₂O₃ and black Cr₃C₂, which were formed under the different SPS temperature. The secondary phase of Cr₂O₃ retarded the processing of densification for spark plasma sintering at 1200 °C. The Cr₂O₃ reacted with Al₂O₃ to form solid solution of Cr₂O₃–Al₂O₃ and with carbon to form Cr₃C₂ as sintering temperature increased to 1350 °C. The characteristics of high heating rate, shorter sintering time for SPS and the formation of secondary phase of Cr₃C₂ effectively reduced the substrate's grain growth, making Al₂O₃–Cr₂O₃/Cr₃C₂ nanocomposites with small grain size.     

Structural,morphological and up-converting luminescence characteristics of nanocrystalline Y2O3:Yb/Er powders obtained via spray pyrolysis

Sub-micronic, spherical Y₂O₃:Yb/Er particles comprising clustered nano-units (70 nm) were prepared via ultrasonic spray pyrolysis from pure nitrate precursor solutions with different Yb/Er dopant ratios. The particles were additionally thermally treated at 1100 °C for 12, 24 and 48 h. The structural and morphological characteristics of particles were studied by X-ray powder diffraction, Fourier transform infrared spectroscopy, field-emission scanning electron microscopy, energy dispersive X-ray analysis and specific surface area (BET) and were further correlated with their advanced optical properties. For the recorded up-conversion emissions, originating from the following Er³⁺ transitions: [²H_9/2→⁴I_15/2] in blue (407–420 nm); [²H_11/2, ⁴S_3/2→⁴I_15/2] green: 510–590 nm; and [⁴F_9/2→⁴I_15/2] in red (640–720 nm) spectral region, the corresponding lifetimes were acquired in the wide temperature range (10–300 K). The most intense green up-conversion emission with the long decay of 550 ms is recorded for Y_1.97Yb_0.02Er_0.01O₃ particles thermally treated at 1100 °C for 24 h.     

Visible light induced photocatalytic activity of Nb2O5/carbon cluster/Cr2O3 composite materials

Nano-sized Nb₂O₅/carbon cluster/Cr₂O₃ composite material was prepared by the calcination of NbCl₅/chromium acetylacetonate/epoxy resin complex under an argon atmosphere. The Pt-loaded Nb₂O₅/carbon cluster/Cr₂O₃ composite material shows the photocatalytic activity under visible light irradiation. The composite material successfully decomposed the water into H₂ and O₂ in the [H₂]/[O₂] ratio of 2. Electron spin resonance spectral examination suggests a two-step electron transfer in the process of Nb₂O₅ → carbon cluster → Cr₂O₃ → Pt.     

Sintering of glass-added BaZn1/3Nb2/3O3 ceramics

The complex perovskite oxide Ba(Zn_1/3Nb_2/3)O₃ (BZN) has been studied for its attractive dielectric properties which place this material interesting for applications as multilayer ceramics capacitors or hyperfrequency resonators. This material is sinterable at low temperature with combined glass phase–lithium salt additions, and exhibits, at 1 MHz very low dielectric losses combined with relatively high dielectric constant and a good stability of this later versus temperature. The 2 wt.% of ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of LiF-added BZN sample sintered at 900 °C exhibits a relative density higher than 95% and attractive dielectric properties: a dielectric constant ?_r of 39, low dielectrics losses (tan(δ) < 10⁻³) and a temperature coefficient of permittivity τ_? of 45 ppm/°C⁻¹. The 2 wt.% ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of B₂O₃-added BZN sintered at 930 °C exhibits also attractive dielectric properties (?_r = 38, tan(δ) < 10⁻³) and it is more interesting in terms of temperature coefficient of the permittivity (τ_? = −5 ppm/°C). Their good dielectric properties and their compatibility with Ag electrodes, make these ceramics suitable for L.T.C.C applications.     

Improved SnO2–Sb2O4 based anode modified with Cr3C2 and CNT for phenol oxidation

Chromium carbide (Cr₃C₂) and carbon nanotubes (CNTs) improved Ti/SnO₂–Sb₂O₄ electrodes were successfully fabricated using pulse electro-co-deposition technique. The morphologies and phase constituents of these electrodes were characterized using scanning electron microscope (SEM) and X-ray diffraction (XRD). The service lifetime of anode was significantly increased by adding Cr₃C₂. The service lifetime of Ti/SnO₂–Sb₂O₄–Cr₃C₂ and Ti/SnO₂–Sb₂O₄–CNT–Cr₃C₂ electrode was 7.4 times and 5.6 times longer than that of the Ti/SnO₂–Sb₂O₄ electrode, respectively. The catalytic activity of phenol oxidation on these electrodes was systematically investigated by the cyclic voltammetry and the chemical oxygen demand (COD) test. The Ti/SnO₂–Sb₂O₄–CNT–Cr₃C₂ electrode shows the highest evolution oxygen potential, COD removal and current efficiency (CE).     

Synthesis of graphene/α-Fe2O3 nanospindles by hydrothermal assembly and their lithium storage performance

Nanocomposite of graphene/α-Fe₂O₃ (G/α-Fe₂O₃) nanospindles was synthesized by a simple hydrothermal assembly method followed by thermal treatment. The α-Fe₂O₃ nanospindles were evenly enwrapped by the graphene nanosheets. When evaluated as an anode for Li-ion batteries (LIBs), the G/α-Fe₂O₃ nanocomposite showed enhanced cycling performance and rate capability compared to pure α-Fe₂O₃. G/α-Fe₂O₃ retained a reversible capacity of 607 mAh g^?1 after 100 cycles at 100 mA g^?1-, which is far higher than that (160 mAh g^?1) of α-Fe₂O₃. The superior electrochemical performance of G/α-Fe₂O₃ can be attributed to the protection effect of graphene nanosheets to accommodate the volume change of α-Fe₂O₃ during lithiation/delithiation.     

Structural anomaly and electrical relaxation in (Na2/3Pb1/3)(Mn1/2Nb1/2)O3 ceramics

The X-ray diffraction patterns of (Na_2/3Pb_1/3)(Mn_1/2Nb_1/2)O₃ ceramics were measured within 15–850 K temperature range. The anomaly in the thermal expansion temperature dependence occurred in 250–365 K range. The generalised Cole–Cole model was proposed to describe the measured effective electric permittivity influenced by high electric conduction and the coexistence of two contributions ?*(T,f) = ?*_lattice + ?*_carriers was considered. The analysis of the electric permittivity and conduction exhibited two relaxation processes. The electric conduction relaxation characteristic time values indicated the small polaron mechanism with τ₀ ≈ 10⁻¹³ s occurring in 240–345 K range and the ionic mechanism with τ₀ ≈ 10⁻¹¹ s involved in the other relaxation occurring in the 320–510 K range. The ionic relaxation process was ascribed to a subsystem of defects, which was weakly interrelated to the anomaly in thermal expansion of the (Na_2/3Pb_1/3)(Mn_1/2Nb_1/2)O₃ ceramics. The Gate model was proposed to describe the ionic relaxation mechanism.     

Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

Structural and spectroscopic properties of Nd:Y2Si2O7 phosphors

Phosphors of α-Y₂Si₂O₇ doped with Nd³⁺ ions were prepared using the sol–gel technique. Nano-sized crystalline phosphor powders were obtained by annealing the dried gels at 960 °C. The crystallization properties of the phosphor powders were determined from their XRD patterns. The α-Y₂Si₂O₇ phase was the only phase observed in all compositions. As the amount of amorphous SiO₂ in the composition was increased, the crystalline sizes and the widths of the size distribution curves were found to decrease from 17.8 nm to 10.6 nm and from 15.6 nm to 12.2 nm, respectively. The spectroscopic properties of the powders were studied by measuring the luminescence and the decay patterns of the ⁴F_3/2→ ⁴I_9/2 and ⁴F_3/2→ ⁴I_11/2 transitions between 50 K and 310 K. No appreciable effect of the crystallite sizes on the average lifetime of the ⁴F_3/2 level was observed at temperatures below 100 K. The effect of temperature, however, becomes relevant above 100 K as the size of α-Y₂Si₂O₇ nano-crystal becomes smaller.     

A kinetic study of lithium transport in the sol–gel Cr0.11V2O5.16 mixed oxide

The kinetics of the electrochemical lithium insertion reaction in the sol–gel chromium–vanadium mixed oxide Cr_0.11V₂O_5.16 has been investigated using ac impedance spectroscopy. The chemical lithium diffusion coefficient is found to be in the range 10⁻⁸/10⁻¹² cm²/s depending the Li content over the wide Li composition range 0 < x < 2 in Li_xCr_0.11V₂O_5.16. The evolution of the cathode impedance is investigated as a function of the lithium content and cycles. The results are discussed in relation with the cycling properties of the electrode material and the unusual structural response of the sol–gel mixed oxide which consists of a single phase behaviour with a continuous cell volume expansion of 6–7% in the 0 < x < 2 range for Li_xCr_0.11V₂O_5.16. For x < 1, a comparison with available kinetic data for the parent oxide indicates a very close behaviour. Cr_0.11V₂O_5.16 is shown to be the best V₂O₅-based cathode material with an initial specific capacity of 280 mAh/g at C/10 rate and still 240 mAh/g after 50 cycles in the 3.8–2 V potential range. The present kinetic data seem to indicate its better cycling behaviour mainly originates from its specific structural response rather than from kinetic reasons.     

Novel high-capacity hybrid layered oxides NaxLi1.5-xNi0.167Co0.167Mn0.67O2 as promising cathode materials for rechargeable sodium ion batteries

Relatively low capacity is a technological bottleneck of the development of sodium ion batteries. Herein, we present a series of hybrid layered cathode materials Na_xLi_1.5-xNi_0.167Co_0.167Mn_0.67O₂ (x?=?0.5, 0.6, 0.7, 0.8, 0.9, 1) with composite crystalline structures, which are prepared by co-precipitation method. The combined analysis of XRD, SEM and TEM reveals that the materials are composed of P2 structure, α-NaFeO₂ structure and small amount of Li₂MnO₃. Among the as-prepared materials, Na_0.6Li_0.9Ni_0.167Co_0.167Mn_0.67O₂ delivers an initial reversible capacity of 222?mA?h?g^?1 at 20?mA?g^?1. Even at 100?mA?g^?1, it shows a remarkable discharge capacity of 125?mA?h?g^?1 in the first cycle and remains 60?mA?h?g^?1 after 300 cycles. Such high capacity is achieved by the specific composite structure and sodium ions are proved to be able to intercalate/deintercalate in Li_1.5Ni_0.167Co_0.167Mn_0.67O₂ with α-NaFeO₂ structure. The Ex-situ XRD results of Na_0.6Li_0.9Ni_0.167Co_0.167Mn_0.67O₂ in the first cycle show that the P2 structure is well maintained along with irreversible phase transition of α-NaFeO₂ structure, which is responsible for the long-term capacity fading. Owing to the high discharge capacity, the novel hybrid layered oxides Na_xLi_1.5-xNi_0.167Co_0.167Mn_0.67O₂ with composite structures can be considered as promising cathode materials to promote progress toward sodium-ion batteries.     

Effect of A2O3 (A = La,Y, Cr,Al) on thermal and crystallization kinetics of borosilicate glass sealants for solid oxide fuel cells

Influence of various intermediate oxides on thermal, structural and crystallization kinetics of 30BaO–40SiO₂–20B₂O₃–10A₂O₃ (A = Y, La, Al, Cr) glasses has been studied. The highest glass transition temperature (T_g) with high thermal stability is observed in Y₂O₃ containing glasses as compared to other glasses. The thermal expansion coefficient (TEC) increases with increasing heat treatment duration in all the glasses. The maximum increase in TEC is observed in Cr₂O₃ containing glass ceramics. FTIR study showed that transmission bands due to silicate and borate chains become sharper with splitting after heat treatment. A selected glass sample (BaCr) has been tested for interaction and adhesion with Crofer 22 APU interconnect material for its application as a sealant in solid oxide fuel cell.     

The effect of nano-Cr2O3 on solid-solution assisted sintering of MgO refractories

The effect of Cr₂O₃ particle size on the densification of magnesia refractories was investigated. Magnesia grains (<45 μm) were mixed with 2 wt% of micro-Cr₂O₃ (2 μm) and nano-Cr₂O₃ particles (10–20 nm) and sintered at 850–1450 °C, for 5 h in air. The progress of the densification and phase evolution of samples was studied with the support of X-ray diffraction phase analysis (XRD), Fourier transformer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). It was shown that the densification of magnesia was enhanced by reducing the particle size of the added chromia to the range of 20 nm. According to the phase analysis results, the higher dissolution rate of Cr₂O₃ in MgO in the MgO–Cr₂O₃ system was responsible for the faster densification of nano-Cr₂O₃ containing mixes.     

Processing and properties of luminescent Cr3+ doped transparent alumina ceramics

Transparent Cr₂O₃-doped alumina ceramics were prepared by slip casting, followed by pre-sintering in ambient atmosphere and hot isostatic pressing. The effect of dopant concentration on material properties, including microstructure and optical properties was evaluated. Real in-line transmittance in the range of 20–44 % was measured for the ceramics with the mean grain size <520 nm: the transmittance decreased with increasing grain size and Cr content. The excitation spectra consisted of two broad bands with maxima at 404 nm and 558 nm, corresponding to ⁴A_2g → ⁴T_1g and ⁴A_2g → ⁴T_2g transitions of Cr³⁺ ions in octahedral sites of α-Al₂O₃. The intensive deep red narrow emissions under violet/green light excitation, R-lines (²E_g → ⁴A_2g transition), were observed at 692.5 nm and 693.8 nm, that are very close to ruby single crystal. The highest emission was achieved at the Cr³⁺ concentration of 0.4 at.%. The luminescence decay curves exhibited single-exponential behaviour with decay times of ∼3.6 ms.     

Low temperature sintering and microwave dielectric properties of Ce2(WO4)3 ceramics

Ce₂(WO₄)₃ ceramics have been synthesized by the conventional solid-state ceramic route. Ce₂(WO₄)₃ ceramics sintered at 1000 °C exhibited ?_r = 12.4, Qxf = 10,500 GHz (at 4.8 GHz) and τ_f = −39 ppm/°C. The effects of B₂O₃, ZnO–B₂O₃, BaO–B₂O₃–SiO₂, ZnO–B₂O₃–SiO₂ and PbO–B₂O₃–SiO₂ glasses on the sintering temperature and microwave dielectric properties of Ce₂(WO₄)₃ were investigated. The Ce₂(WO₄)₃ + 0.2 wt% ZBS sintered at 900 °C/4 h has ?_r = 13.7, Qxf = 20,200 GHz and τ_f = −25 ppm/°C.     

Original synthesis of chromium (III) oxide nanoparticles

Nanosized chromium (Cr₂O₃) oxide was prepared by the common thermal decomposition of Cr(NO₃)₃·9H₂O chromium (III) nitrate nonahydrate. Prior to the heat treatment at 550 °C, the commercial reagent was first dissolved in a colloidal silica solution and then dried at a low temperature to slowly evaporate the aqueous solvent. The SiO₂/Cr(NO₃)₃·9H₂O weight ratio (R) was changed from 0 to 2. The various Cr₂O₃ powders were characterized by XRD, FTIR, nitrogen adsorption, SEM and TEM techniques. A maximum specific surface area of 113 m² g^?1, associated with a pore volume of 0.72 cm³ g^?1, was obtained for the Cr₂O₃ powder prepared with R = 2. These pristine chromium oxide nanoparticles, with a slightly sintered sphere-shaped morphology, exhibited a 10 nm particle size with a monocrystalline character as demonstrated by the TEM and XRD correlation.     

Preparation and characterization of Cr2O3-TiO2-Al2O3-V2O5 green pigment

Green pigments with high near infrared reflectance based on a Cr₂O₃-TiO₂-Al₂O₃-V₂O₅ composition have been synthesized. Cr₂O₃ was used as the host component and mixtures of TiO₂, Al₂O₃ and V₂O₅ were used as the guest components. TiO₂, Al₂O₃, and V₂O₅ were mixed into 39 different compositions. The spectral reflectance and the distribution of pigment powder were determined using a spectrophotometer and a scanning electron microscope, respectively. It was found that a pigment powder sample S9 with a Cr₂O₃-TiO₂-Al₂O₃-V₂O₅ composition of 80, 4, 14 and 2 wt%, respectively, gives a maximum near infrared solar reflectance of 82.8% compared with 49.0% for pure Cr₂O₃. The dispersion of pigment powders in a ceramic glaze was also studied. The results show that the pigment powder sample S9 is suitable for use as a coating material for ceramic-based roofs.     

Enhanced high rate capability of dual-phase Li4Ti5O12–TiO2 induced by pseudocapacitive effect

The dual-phase Li₄Ti₅O₁₂–TiO₂ nanocomposite is successfully synthesized by a hydrothermal route with adding thiourea. The electrochemical performance of the dual-phase nanocomposite as anode for lithium-ion batteries is investigated by the galvanostatic method, cyclic voltammetry and electrochemical impedance spectra. It is demonstrated that the dual-phase Li₄Ti₅O₁₂–TiO₂ nanocomposite presents the improved electrochemical performance over individual single phase Li₄Ti₅O₁₂ and anatase TiO₂ samples. After 300 cycles at 1 C, the dual-phase Li₄Ti₅O₁₂–TiO₂ nanocomposite can still maintain the large discharge capacity of 116 mAh g⁻¹. It indicates that the as-prepared nanocomposite can endure great changes of various discharge current densities to retain a good stability. The large discharge capacity of 132 mAh g⁻¹ is also obtained at the large current density of 1600 mA g⁻¹ upon cycling. In particular, as verified by the cyclic voltammetry, the pseudocapacitive effect is induced due to the presence of abundant phase interfaces in the dual-phase Li₄Ti₅O₁₂–TiO₂ nanocomposite, which is beneficial to the enhanced high rate capability and good cycle stability.     

Structural and luminescence properties of RE (RE = Eu, Tb):(MgCa)2Bi4Ti5O20 ceramics

Rare-earth ions (Eu³⁺, Tb³⁺) activated magnesium calcium bismuth titanate [(MgCa)₂Bi₄Ti₅O₂₀] ceramics were prepared by conventional solid state reaction method for their structural and luminescence properties. By using XRD patterns, the structural properties of ceramic powders have been analyzed. Emission spectrum of Eu³⁺:(MgCa)₂Bi₄Ti₅O₂₀ ceramic powder has shown strong red emission at 615 nm (⁵D₀ → ⁷F₂) with an excitation wavelength λ_exci = 393 nm and Tb³⁺:(MgCa)₂Bi₄Ti₅O₂₀ ceramic powder has shown green emission at 542 nm (⁵D₄ → ⁷F₅) with an excitation wavelength λ_exci = 376 nm. In addition, from the measurements of scanning electron microscopy (SEM), Fourier transform-infrared (FTIR) and energy dispersive X-ray analysis (EDAX) results the morphology, structure and elemental analysis of these powder ceramics have been studied.