Sintering mechanism and dielectric properties of LiTaO3 matrix composites with the addition of Al2O3 particles

Highly densified Al₂O₃/LiTaO₃ (ALT) ceramic composites were fabricated by hot-pressing in a nitrogen atmosphere. The addition of Al₂O₃ particles could significantly improve the densification of LiTaO₃. Sintering mechanism of the LiTaO₃ ceramic incorporated with Al₂O₃ particles is proposed. Dielectric constant of 5 vol.% Al₂O₃/LiTaO₃ (5ALT) composite ceramic was slightly increased in the range from 30 kHz to 10⁶ Hz, but the dielectric loss was lowered in the whole range from 10³ Hz to 10⁶ Hz. Piezoelectric constant (d₃₃) of the 5ALT ceramic composite is about 50% of that of LiTaO₃ single crystal.     

Effect of CeO2 addition on densification and microstructure of Al2O3-YSZ composites

Alumina (Al₂O₃) and alumina-yttria stabilized zirconia (YSZ) composites containing 3 and 5 mass% ceria (CeO₂) were prepared by spark plasma sintering (SPS) at temperatures of 1350-1400 °C for 300 s under a pressure of 40 MPa. Densification, microstructure and mechanical properties of the Al₂O₃ based composites were investigated. Fully dense composites with a relative density of approximately 99% were obtained. The grain growth of alumina was inhibited significantly by the addition of 10 vol% zirconia, and formation of elongated CeAl₁₁O₁₈ grains was observed in the ceria containing composites sintered at 1400 °C. Al₂O₃-YSZ composites without CeO₂ had higher hardness than monolithic Al₂O₃ sintered body and the hardness of Al₂O₃-YSZ composites decreased from 20.3 GPa to 18.5 GPa when the content of ZrO₂ increased from 10 to 30 vol%. The fracture toughness of Al₂O₃ increased from 2.8 MPa m^1/2 to 5.6 MPa m^1/2 with the addition of 10 vol% YSZ, and further addition resulted in higher fracture toughness values. The highest value of fracture toughness, 6.2 MPa m^1/2, was achieved with the addition of 30 vol% YSZ.     

Mechanical properties of Al2O3-Cr2O3/Cr3C2 nanocomposite fabricated by spark plasma sintering

The fine grains of Al₂O₃-Cr₂O₃/Cr-carbide nanocomposites were prepared by employing recently developed spark plasma sintering (SPS) technique. The initial materials were fabricated by a metal organic chemical vapor deposition (MOCVD) process, in which Cr(CO)₆ was used as a precursor and Al₂O₃ powders as matrix in a spouted chamber. The basic mechanical properties like hardness, fracture strength and toughness, and the nanoindentation characterization of nanocomposites such as Elastics modulus (E), elastic work (W_e) and plastic work (W_p) were analyzed. The microstructure of dislocation, transgranular and step-wise fracture surface were observed in the nanocomposites. The nanocomposites show fracture toughness of (4.8 MPa m^1/2) and facture strength (780 MPa), which is higher than monolithic alumina. The strengthening mechanism from the secondary phase and solid solution are also discussed in the present work. Nanoindentation characterization further illustrates the strengthening of nanocomposites.     

Development of input output relationships for self-healing Al2O3/SiC ceramic composites with Y2O3 additive using design of experiments

Al₂O₃/SiC ceramic composites with Y₂O₃ as an additive, was synthesized using the Taguchi method of design of experiments, so as to develop statistically sound input output relationships. The proportion of SiC was varied from 12 to 21 vol.% whereas that of Y₂O₃ was varied from 2.5 to 4 vol.%. The composites were sintered at 1500 °C for a soaking time period of 12 h in an air atmosphere. Cracks were induced on the composite surface using a Vickers indenter with a load varying between 20 and 40 kg. Fractographical analyses have been carried out using optical and/or scanning electron microscopy to investigate the surface crack propagation behavior. Thermal aging at 1300 °C in the time range of 0.5-12.5 h was applied to find optimal conditions for healing of the pre-cracked samples. The output parameters such as crack length, healed crack length, hardness and fracture toughness of the samples were correlated with appropriate inputs such as contents of SiC and Y₂O₃, crack-healing temperature, healing time, compaction pressure, indentation load using statistical analysis. Further, the extent of influence, exerted by pertinent input parameters on output parameters, was also identified.     

Sintering of Al2O3-SiC composite from sol-gel method with MgO, TiO2 and Y2O3 addition

Al₂O₃-SiC composite ceramics were prepared by pressureless sintering with and without the addition of MgO, TiO₂ and Y₂O₃ as sintering aids. The effects of these compositional variables on final density and hardness were investigated. In the present article at first α-Al₂O₃ and β-SiC nano powders have been synthesized by sol-gel method separately by using AlCl₃, TEOS and saccharose as precursors. Pressureless sintering was carried out in nitrogen atmosphere at 1600 °C and 1630 °C. The addition of 5 vol.% SiC to Al₂O₃ hindered densification. In contrast, the addition of nano MgO and nano TiO₂ to Al₂O₃-5 vol.% SiC composites improved densification but Y₂O₃ did not have positive effect on sintering. Maximum density (97%) was achieved at 1630 °C. Vickers hardness was 17.7 GPa after sintering at 1630 °C. SEM revealed that the SiC particles were well distributed throughout the composite microstructures. The precursors and the resultant powders were characterized by XRD, STA and SEM.     

Effects of CaSiO3 addition on sintering behavior and microwave dielectric properties of Al2O3 ceramics

The effects of CaSiO₃ addition on the sintering behavior and microwave dielectric properties of Al₂O₃ ceramics have been investigated. The addition of CaSiO₃ into Al₂O₃ ceramics resulted in the emergence of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which acting as liquid sintering aids can effectively lower the sintering temperature of Al₂O₃ ceramic. The Q × f value of Al₂O₃-CaSiO₃ ceramics decreased with the CaSiO₃ addition increasing because of the lower Q × f value of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈. Compared with the pure CaSiO₃ ceramic, the Al₂O₃-CaSiO₃ ceramic with 20 wt% CaSiO₃ addition possessed good dielectric properties of ?_r = 9.36 and Q × f = 13,678 GHz at the similar sintering temperature.     

Effect of Al2O3 particle size on preparation and properties of ZTA ceramics formed by gelcasting

Zirconia-toughened alumina (ZTA) ceramics were prepared using three different kinds of Al₂O₃ powders (marked PW-A average particle size: 7.53 μm, marked PW-B average particle size: 1.76 μm, marked PW-C average particle size: 0.61 μm) by gelcasting. Effect of Al₂O₃ particle size on zeta potential, dispersant dosage and solid volume fractions of ZTA suspensions as well as the mechanical properties of ZTA green bodies and ceramics were investigated. The optimum dosages of dispersant for ZTA suspensions prepared by PW-A, PW-B and PW-C are 0.4 wt%, 0.5 wt% and 0.7 wt%, respectively. The highest solid volume fractions of ZTA suspensions can reach 62 vol% (SP-A), 60 vol% (SP-B) and 52 vol% (SP-C), respectively. The green bodies show a bending strength as high as 20 MPa, which can meet the requirement of machining. The Al₂O₃ powder with fine particle size is beneficial to the improvement of mechanical properties. The ZTA ceramics prepared by PW-B Al₂O₃ powder show the highest bending strength (680 MPa) and toughness (7.49 MPa m^1/2).     

Effects of Al2O3 addition on the sintering behavior and microwave dielectric properties of CaSiO3 ceramics

The effects of Al₂O₃ addition on the densification, structure and microwave dielectric properties of CaSiO₃ ceramics have been investigated. The Al₂O₃ addition results in the presence of two distinct phases, e.g. Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which can restrict the growth of CaSiO₃ grains by surrounding their boundaries and also improve the bulk density of CaSiO₃-Al₂O₃ ceramics. However, excessive addition (≥2 wt%) of Al₂O₃ undermines the microwave dielectric properties of the title ceramics since the derived phases of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈ have poor quality factor. The optimum amount of Al₂O₃ addition is found to be 1 wt%, and the derived CaSiO₃-Al₂O₃ ceramic sintered at 1250 °C presents improved microwave dielectric properties of ?_r = 6.66 and Q × f = 24,626 GHz, which is much better than those of pure CaSiO₃ ceramic sintered at 1340 °C (Q × f = 13,109 GHz).     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Processing and physical properties of Al2O3/aluminum alloy composites

Porous aluminum oxide (Al₂O₃) preforms were formed by sintering in air at 1200 °C for 2 h. A356, 6061, and 1050 aluminum alloys were infiltrated into the preforms by squeeze casting in order to fabricate Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites, respectively, with different volumes of aluminum alloy content. The content of aluminum alloy in the composites was 10–40% by volume. The resistivity of Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites decreased dramatically from 6.41 × 10¹² to 9.77 × 10⁻⁴, 7.28 × 10⁻⁴, and 6.24 × 10⁻⁴ Ω m, respectively, the four-points bending strength increased from 397 to 443, 435.1, 407.2 MPa, respectively, and the deviations were smaller than 2%. From SEM microstructural analysis and TEM bright field images, the pore volume fraction and the relative density of the composites were the most important factors that affected the physical and mechanical properties. The ceramic phase and alloy phase in Al₂O₃/aluminum alloy composites were found to be homogenized and uniformly distributed using electrical and mechanical properties analysis, microstructure analysis, and image analysis.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Tribological properties of Al2O3 nanoparticles as lubricating oil additives

Nano-scale Al₂O₃ spherical particles, prepared via a hydrothermal method and modified by silane coupling agent, can be well-dispersed in lubricating oil. The tribology properties of Al₂O₃ nanoparticles as lubricating oil additives have been studied by four-ball and thrust-ring friction test, which illustrate that the modified Al₂O₃ nanoparticles can effectively improve the lubricating behaviors compared to the base oil. When the added concentration is 0.1 wt%, the friction coefficient and the wear scar diameter are both smallest. The lubrication mechanism is that a self-laminating protective film is formed on the friction surface and the wear behavior changes from sliding friction to rolling friction.     

Effect of fiber type on mechanical properties of short carbon fiber reinforced B4C composites

In order to enhance the mechanical properties of B₄C without density increase, the short carbon fibers M40, M55J and T700 reinforced B₄C ceramic composites were fabricated by hot-pressing process. The addition of the carbon fibers accelerates the densification of the B₄C, decreases their densities, and improves their strength and toughness. The enhancement effects of the three kinds of carbon fibers were studied by investigating the density, Vickers hardness and the mechanical properties such as flexural strength, flexural modulus and fracture toughness of the composites. The fiber type has a great influence on the mechanical properties and enhancement of the short carbon fiber reinforced B₄C composites. The flexible carbon fiber with high strength and low modulus such as T700 is appropriate to reinforce the B₄C matrix ceramic composites.     

Relationship between fracture toughness characteristics and morphology of sintered Al2O3 ceramics

The influence of sintering temperature and soaking time on fracture toughness of Al₂O₃ ceramics has been investigated. The samples were prepared by solid state sintering at 1500, 1600 and 1700 °C for different soaking time periods. The fracture toughness of the sintered samples was determined by inducing cracks using Vickers indentation technique. Microstructural investigations on fracture surfaces obtained by three point bend test mode were made and correlated with fracture toughness. Crack deflection in the samples sintered at 1500 and 1600 °C for which ranges of fracture toughness are 5.2–5.4 and 5.0–5.6 MPa m^1/2 respectively, are found. The samples sintered at 1700 °C have lower fracture toughness ranging between 4.6 and 5.0 MPa m^1/2. These samples have larger grains and transgranular fracture mode is predominant. The crack deflection has further been revealed by SEM and AFM observations on fracture surface and fracture surface roughness respectively.     

Laser machining of Al2O3-ZrO2 (3%Y2O3) eutectic composite

In this work we present the study of the interaction between NIR pulsed laser and Al₂O₃-ZrO₂ (3%Y₂O₃) eutectic composite. The effect produced by modifying the reference position as well as the working conditions and laser beam features has been studied when the samples are processed by means of pulse bursts.The samples were obtained by the laser floating zone technique using a CO₂ laser system. The laser machining was carried out with a Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulse-widths in the nanosecond range.Geometric dimensions, i.e. ablated depth, machined width and removed volume as well as ablation yield of the resulting holes have been studied. We have described and discussed the morphology, composition and microstructure of the processed samples.     

Fabrication of novel multilayer Al2O3-(m-ZrO2)/t-ZrO2 fibrous ceramics composites

A novel layered microstructure in the Al₂O₃/ZrO₂ composites system was fabricated by the multipass extrusion method. The microstructure consisted with very fine alternate lamina of Al₂O₃-(m-ZrO₂) and t-ZrO₂. The composites were designed in such a way that a small group of 7 cylindrical alternate layers of Al₂O₃-(m-ZrO₂) and t-ZrO₂ made a concentric microgroup around 40 μm in diameter, with a common boundary layer between the adjacent groups. The thickness of both layers was around 2-3 μm. The microstructure was unidirectionally aligned throughout the composites. The composite microstructure was fibrous due to the unidirectional orientation of these microgroups. Detailed microstructure of the fabricated composites was characterized by SEM. The effect of the concentric layered microstructure on mechanical behavior was discussed. Material properties such as density, bending strength, Vickers hardness and fracture toughness were measured and evaluated depending on different sintering temperatures.     

Matrix–filler interactions in polysilazane-derived ceramics with Al2O3 and ZrO2 fillers

Interactions between a poly(vinyl)silazane and Al₂O₃ or Y₂O₃-stabilised ZrO₂ fillers were studied during the fabrication of polysilazane-derived bulk ceramics in order to investigate the influence of oxide fillers on resulting properties. Specimens were produced by coating of the filler powders with the polysilazane, warm-pressing of the resulting composite powders, and pyrolytic conversion in flowing N₂ at various temperatures between 1000 °C and 1400 °C. Significant differences in densification were observed, depending on the filler used. Reactions between the polysilazane-derived matrix and Al₂O₃ or ZrO₂ at temperatures ≥1300 °C resulted in the formation of Si₅AlON₇ or ZrSiO₄, respectively. Reactivity in the polysilazane-derived component was a result of SiO₂ contamination caused primarily by adsorbed species on the filler particle surface. Knowledge of polysilazane/filler interface processes is found to be decisive for the prediction of properties such as shrinkage and porosity, which heavily influence performance of a material.     

Microstructure and mechanical properties of Al2O3/Er3Al5O12 eutectic rods grown by the laser-heated floating zone method

Eutectic rods of Al₂O₃-Er₃Al₅O₁₂ were grown by directional solidification using the laser-heated floating zone method at rates in the range 25-1500 mm/h. Their microstructure and mechanical properties (hardness, toughness and strength) were investigated as a function of the growth rate. A homogeneous and interpenetrated microstructure was found in most cases, and interphase spacing decreased with growth rate following the Hunt-Jackson law. Hardness increased slightly as the interphase spacing decreased while toughness was low and independent of the microstructure. The rods presented very high bending strength as a result of the homogeneous microstructure, and their strength increased rapidly as the interphase spacing decreased, reaching a maximum of 2.7 GPa for the rods grown at 750 mm/h. The bending strength remained constant up to 1300 K and decreased above this temperature. The relationship between the microstructure and the mechanical properties was established from the analysis of the microstructure and of the fracture mechanisms.     

Properties and rapid consolidation of nanostructured Al2O3-Al2SiO5 composites by high frequency induction heated sintering

The rapid sintering of nanostructured Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites was investigated by a high-frequency induction heating sintering process. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition of grain growth. Highly dense nanostructured Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites were produced with simultaneous application of a 80 MPa pressure and induced output current of a total power capacity (15 kW) within 3 min. The sintering behavior, grain size and mechanical properties of Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites were investigated.