Design of a novel bifunctional catalyst IrFe/Al2O3 for preferential CO oxidation

In this study, a novel bifunctional catalyst IrFe/Al₂O₃, which is very active and selective for preferential oxidation of CO under H₂-rich atmosphere, has been developed. When the molar ratio of Fe/Ir was 5/1, the IrFe/Al₂O₃ catalyst performed best, with CO conversion of 68% and oxygen selectivity towards CO₂ formation of 86.8% attained at 100 °C. It has also been found that the impregnation sequence of Ir and Fe species on the Al₂O₃ support had a remarkable effect on the catalytic performance; the activity decreased following the order of IrFe/Al₂O₃ > co-IrFe/Al₂O₃ > FeIr/Al₂O₃. The three catalysts were characterized by XRD, H₂-TPR, FT-IR and microcalorimetry. The results demonstrated that when Ir was supported on the pre-formed Fe/Al₂O₃, the resulting structure (IrFe/Al₂O₃) allowed more metallic Ir sites exposed on the surface and accessible for CO adsorption, while did not interfere with the O₂ activation on the FeO_x species. Thus, a bifunctional catalytic mechanism has been proposed where CO adsorbed on Ir sites and O₂ adsorbed on FeO_x sites; the reaction may take place at the interface of Ir and FeO_x or via a spill-over process.     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

Comparison of catalytic activity and selectivity of Pd/(OSC + Al2O3) and (Pd + OSC)/Al2O3 catalysts

The effect of the Pd addition method into the fresh Pd/(OSC + Al₂O₃) and (Pd + OSC)/Al₂O₃ catalysts (OSC material = Ce_xZr_1−xO₂ mixed oxides) was investigated in this study. The CO + NO and CO + NO + O₂ model reactions were studied over fresh and aged catalysts. The differences in the fresh catalysts were insignificant compared to the aged catalysts. During the CO + NO reaction, only small differences were observed in the behaviour of the fresh catalysts. The light-off temperature of CO was about 20 °C lower for the fresh Pd/(OSC + Al₂O₃) catalyst than for the fresh (Pd + OSC)/Al₂O₃ catalyst during the CO + NO + O₂ reaction. For the aged catalysts lower NO reduction and CO oxidation activities were observed, as expected. Pd on OSC-containing alumina was more active than Pd on OSC material after the agings. The activity decline is due to a decrease in the number of active sites on the surface, which was observed as a larger Pd particle size for aged catalysts than for fresh catalysts. In addition, the oxygen storage capacity of the aged Pd/(OSC + Al₂O₃) catalyst was higher than that of the (Pd + OSC)/Al₂O₃ catalyst.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

A comparison study on non-thermal plasma-assisted catalytic reduction of NO by C3H6 at low temperatures between Ag/USY and Ag/Al2O3 catalysts

A comparison study was carried out on non-thermal plasma (NTP)-assisted selective catalytic reduction (SCR) of NO_x by propene over Ag/USY and Ag/Al₂O₃ catalysts. Ag/USY was almost inactive in thermal SCR while it showed obvious activities in NTP-assisted SCR at 100 °C–200 °C. Although the NO_x conversion over Ag/Al₂O₃ was also enhanced at 300 °C–400 °C by the assistance of NTP, it was ineffective below 250 °C. The intermediates over Ag/USY and Ag/Al₂O₃ were investigated using in situ DRIFTS method. It was found that key intermediates in HC-SCR, such as NCO, CN, oxygenates and some N-containing organic species were enriched after the assistance of NTP. The differences in the behaviors of above intermediates were not found between these two kinds of catalysts. However, some evidences suggested that different properties of the absorbed NO_x species resulted in the distinction of SCR reactions over Ag/USY and Ag/Al₂O₃. TPD profiles of Ag/Al₂O₃ showed that nitrates formed over the catalyst were quite stable at low temperatures, which might occupy the active sites and were unfavorable to SCR reactions. The nitrates over Ag/USY were unstable, among which the unidentate nitrate species is probably contributed to the SCR reactions at low temperatures.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Effect of Pt on the water resistance of Co-zeolites upon the SCR of NOx with CH4

The objective of this work was to study the promotional effect of Pt on Co-zeolite (viz. mordenite, ferrierite, ZSM-5 and Y-zeolite) and Co/Al₂O₃ on the selective catalytic reduction (SCR) of NO_x with CH₄ under dry and wet reaction stream. After being reduced in H₂ at 350°C, the PtCo bimetallic zeolites showed higher NO to N₂ conversion and selectivity than the monometallic samples, as well as a combination of the latter samples such as mechanical mixtures or two-stage catalysts. After the same pretreatment, under wet reaction stream, the bimetallic samples were also more active. Among the other catalysts studied with 5% of water in the feed, (NO = CH₄ = 1000 ppm, O₂ = 2%), the NO conversion dropped to zero over Co_2.0Mor at 500°C and GHSV = 30,000 h⁻¹, whereas it is 20% in Pt_0.5Co_2.0Mor. In Pt/Co/Al₂O₃ the NO_x conversion dropped below 5% with only 2% of water under the same reaction conditions. The specific activity given as molecules of NO converted per total metal atom per second were 16.5 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Fer, 13 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Mor, 4.33 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0ZSM-5 and 0.5 × 10⁻⁴ s⁻¹ for Pt/Co/Al₂O₃. The Y-zeolite-based samples were inactive in both mono and bimetallic samples. The species initially present in the solid were Pt° and Co°, together with Co²⁺ and Pt²⁺ at exchange positions. Co° seems not to participate as an active site in the SCR of NO_x. Those species remained after the reaction but some reorganization occurred. A synergetic effect among the different species that enhances both the NO to NO₂ reaction, the activation of CH₄ and also the ability of the catalyst to adsorb NO, could be responsible for the high activity and selectivity of the bimetallic zeolites.     

Al18B4O33 aluminium borate: A new efficient support for palladium in the high temperature catalytic combustion of methane

Well crystallised aluminium borate Al₁₈B₄O₃₃ has been synthesised from alumina and boric acid with a BET area of 18 m²/g after calcination at 1100 °C. Afterwards, 2 wt.% Pd/Al₁₈B₄O₃₃ was prepared by conventional impregnation of Pd(NO₃)₂ aqueous solution and calcination in air at 500 °C. The catalytic activity of Pd/Al₁₈B₄O₃₃ in the complete oxidation of methane was measured between 300 and 900 °C and compared with that of Pd/Al₂O₃. Pd/Al₁₈B₄O₃₃ exhibited a much lower activity than Pd/Al₂O₃ when treated in hydrogen at 500 °C or aged in O₂/H₂O (90:10) at 800 °C prior to catalytic testing. Surprisingly, a catalytic reaction run up to 900 °C in the reaction mixture induced a steep increase of the catalytic activity of Pd/Al₁₈B₄O₃₃ which became as active as Pd/Al₂O₃. Moreover, the decrease of the catalytic activity observed around 750 °C for Pd/Al₂O₃ and attributed to PdO decomposition into metallic Pd was significantly shifted to higher temperatures (820 °C) in the case of Pd/Al₁₈B₄O₃₃. The existence of two distinct types of PdO species formed on Al₁₈B₄O₃₃ and being, respectively, responsible for the improvement of the activity at low and high temperature was proposed on the basis of diffuse reflectance spectroscopy and temperature-programmed desorption of O₂.     

The effect of oxygen concentration on the reduction of NO with propylene over CuO/γ-Al2O3

The effect of oxygen concentration on the pulse and steady-state selective catalytic reduction (SCR) of NO with C₃H₆ over CuO/γ-Al₂O₃ has been studied by infrared spectroscopy (IR) coupled with mass spectroscopy studies. IR studies revealed that the pulse SCR occurred via (i) the oxidation of Cu⁰/Cu⁺ to Cu²⁺ by NO and O₂, (ii) the co-adsorption of NO/NO₂/O₂ to produce Cu²⁺(NO₃⁻)₂, and (iii) the reaction of Cu²⁺(NO₃⁻)₂ with C₃H₆ to produce N₂, CO₂, and H₂O. Increasing the O₂/NO ratio from 25.0 to 83.4 promotes the formation of NO₂ from gas phase oxidation of NO, resulting in a reactant mixture of NO/NO₂/O₂. This reactant mixture allows the formation of Cu²⁺(NO₃⁻)₂ and its reaction with the C₃H₆ to occur at a higher rate with a higher selectivity toward N₂ than the low O₂/NO flow. Both the high and low O₂/NO steady-state SCR reactions follow the same pathway, proceeding via adsorbed C₃H₇---NO₂, C₃H₇---ONO, CH₃COO⁻, Cu⁰---CN, and Cu⁺---NCO intermediates toward N₂, CO₂, and H₂O products. High O₂ concentration in the high O₂/NO SCR accelerates both the formation and destruction of adsorbates, resulting in their intensities similar to the low O₂/NO SCR at 523–698 K. High O₂ concentration in the reactant mixture resulted in a higher rate of destruction of the intermediates than low O₂ concentration at temperatures above 723 K.     

The activity and characterization of sol–gel Sn/Al2O3 catalyst for selective catalytic reduction of NOx in the presence of oxygen

Catalytic performance of Sn/Al₂O₃ catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO_x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO₂ had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al₂O₃ (SG) catalyst, and the maximum NO₂ conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO_x desorption accompanied with O₂ around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H₂O and SO₂ at low temperature, and the temperature window was also broadened in the presence of H₂O and SO₂, however the NO_x desorption and NO conversion decreased sharply on the 300 ppm SO₂ treated catalyst, the catalytic activity was inhibited by the presence of SO₂ due to formation of sulfate species (SO₄²⁻) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al₂O₃ (SG) was not decreased in the presence of large oxygen.     

On the nature of the silver phases of Ag/Al2O3 catalysts for reactions involving nitric oxide

The nature of the silver phases of Ag/Al₂O₃ catalysts (prepared by silver nitrate impregnation followed by calcination) was investigated by X-ray diffractograms (XRD), transmission electron microscopy (TEM) and UV–VIS analyses and related to the activity of the corresponding materials for the oxidation of NO to NO₂. The UV–VIS spectrum of the 1.2 wt.% Ag/Al₂O₃ exhibited essentially one band associated with Ag⁺ species and the NO₂ yields measured over this material were negligible. A 10 wt.% Ag/Al₂O₃ material showed the presence of oxidic species of silver (as isolated Ag⁺ cations and silver aluminate), but the UV–VIS data also revealed the presence of some metallic silver. The activity for the NO oxidation to NO₂ of this sample was moderate. The same 10% sample either reduced in H₂ or used for the C₃H₆-selective catalytic reduction (SCR) of NO showed a significantly larger proportion of silver metallic phases and these samples displayed a high activity for the formation of NO₂. These data show that the structure and nature of the silver phases of Ag/Al₂O₃ catalysts can markedly change under reaction feed containing only a fraction of reducing agent (i.e. 500 ppm of propene) in net oxidizing conditions (2.5% O₂). The low activity for N₂ formation during the C₃H₆-SCR of NO (reported in an earlier study) over the high loading sample can, therefore, be related to the presence of metallic silver, which is yet a good catalyst for NO oxidation to NO₂. The reverse observations apply for the oxide species observed over the low loading sample, which is a good SCR catalyst but do not oxidize NO to NO₂.     

A new concept in high performance ceria–zirconia oxygen storage capacity material with Al2O3 as a diffusion barrier

CeO₂–ZrO₂ solid solution ((Ce,Zr)O₂) is an indispensable oxygen storage capacity (OSC) material for emission control in gasoline-fuelled automobiles. The high performance OSC material developed in this study is composed of Al₂O₃ as “a diffusion barrier” and (Ce,Zr)O₂ particles in intervening layers on a nanometer scale, and is abbreviated as “ACZ”. The Brunauer–Emmett–Teller (BET) specific surface area (SSA) of ACZ after durability testing in air at 1000 °C was 20 m²/g, which is higher than that of conventional CZ (2 m²/g) composed of (Ce,Zr)O₂ without Al₂O₃. After heat treatment at 1000 °C in air, the particle size of (Ce,Zr)O₂ in ACZ was about 10 nm and that without Al₂O₃ was one-half of the size in pure CZ. The OSC was roughly characterized by the total capacity (OSC-c1) and the oxygen release rate (OSC-r). In a fresh catalyst, ACZ and CZ had almost the same OSC-c1; however, the OSC-r of ACZ was twice as fast as CZ. After durability testing, the OSC-r of both ACZ and CZ were reduced significantly, but the OSC-r of ACZ was about five times as fast as CZ. While the OSC-c1 was hardly influenced by the (Ce,Zr)O₂ crystallite size and Pt particle size on the supports, the OSC-r was influenced by both of these parameters. The improvement of the OSC-r in the fresh catalyst and inhibition of the decrease in the OSC-r after durability testing were achieved by suppression of particle growth of (Ce,Zr)O₂ in ACZ by introducing Al₂O₃ as a diffusion barrier with resultant inhibition of sintering of Pt particles.     

Processing of hot pressed Al2O3–Cr2O3/Cr-carbide nanocomposite prepared by MOCVD in fluidized bed

Nanosized particles dispersed uniformly on Al₂O₃ particles were prepared from the decomposition of precursor Cr(CO)₆ by metal organic chemical vapor deposition (MOCVD) in a fluidized chamber. These nanosized particles consisted of Cr₂O₃, CrC_1−x, and C. A solid solution of Al₂O₃–Cr₂O₃ and an Al₂O₃–Cr₂O₃/Cr₃C₂ nanocomposite were formed when these fluidized powders were pre-sintered at 1000 and 1150 °C before hot-pressing at 1400 °C, respectively. In addition, an Al₂O₃–Cr₂O₃/Cr-carbide (Cr₃C₂ and Cr₇C₃) nanocomposite was formed when the particles were directly hot pressed at 1400 °C. The interface between Cr₃C₂ and Al₂O₃ is non-coherent, while the interface between Cr₇C₃ and Al₂O₃ is semi-coherent.     

A comparative study of Ag/Al2O3 and Cu/Al2O3 catalysts for the selective catalytic reduction of NO by C3H6

The selective catalytic reduction (SCR) of NO by C₃H₆ in excess oxygen was evaluated and compared over Ag/Al₂O₃ and Cu/Al₂O₃ catalysts. Ag/Al₂O₃ showed a high activity for NO reduction. However, Cu/Al₂O₃ showed a high activity for C₃H₆ oxidation. The partial oxidation of C₃H₆ gave surface enolic species and acetate species on the Ag/Al₂O₃, but only an acetate species was clearly observed on the Cu/Al₂O₃. The enolic species is a more active intermediate towards NO + O₂ to yield—NCO species than the acetate species on the Ag/Al₂O₃ catalyst. The Ag and Cu metal loadings and phase changes on Al₂O₃ support can affect the activity and selectivity of Ag/Al₂O₃ and Cu/Al₂O₃ catalysts, but the formation of enolic species is the main reason why the activity of the Ag/Al₂O₃ catalyst for NO reduction is higher than that of the Cu/Al₂O₃ catalyst.     

Inhibition effect of H2O on V2O5/AC catalyst for catalytic reduction of NO with NH3 at low temperature

The inhibition effect of H₂O on V₂O₅/AC catalyst for NO reduction with NH₃ is studied at temperatures up to 250 °C through TPD, elemental analyses, temperature-programmed surface reaction (TPSR) and FT-IR analyses. The results show that H₂O does not reduce NO and NH₃ adsorption on V₂O₅/AC catalyst surface, but promotes NH₃ adsorption due to increases in Brønsted acid sites. Many kinds of NH₃ forms present on the catalyst surface, but only NH₄⁺ on Brønsted acid sites and a small portion of NH₃ on Lewis acid sites are reactive with NO at 250 °C or below, and most of the NH₃ on Lewis acid sites does not react with NO, regardless the presence of H₂O in the feed gas. H₂O inhibits the SCR reaction between the NH₃ on the Lewis acid sites and NO, and the inhibition effect increases with increasing H₂O content. The inhibition effect is reversible and H₂O does not poison the V₂O₅/AC catalyst.     

Effect of Rh loading on the performance of Rh/Al2O3 for methane partial oxidation to synthesis gas

Catalytic performance for partial oxidation of methane (POM) to synthesis gas was studied over the Rh/Al₂O₃ catalysts with Rh loadings between 0.1 and 3 wt%. It was found that the ignition temperature of POM reaction increased with the decreasing of the Rh loadings in the catalysts. For the POM reaction over the catalysts with high (≥1 wt%) Rh loadings, steady-state reactivity was observed. For the reaction over the catalysts with low (≤0.25 wt%) Rh loadings, however, oscillations in CH₄ and reaction products (CO, H₂, and CO₂) were observed. Comparative studies using H₂-TPR, O₂-TPD and high temperature in situ Raman spectroscopy techniques were carried out in order to elucidate the relation between the redox property of the Rh species in the Rh/Al₂O₃ with different Rh loadings and the performance of the catalysts for the reaction. Three kinds of oxidized rhodium species, i.e. the rhodium oxide species insignificantly affected by the support (RhO_x), that intimately interacting with the Al₂O₃ surface (RhⁱO_x) and the Rh(AlO₂)_y species formed by diffusion of rhodium oxides in to sublayers of Al₂O₃ [C.P. Hwang, C.T. Yeh, Q.M. Zhu, Catal. Today, 51 (1999) 93.], were identified by H₂-TPR and O₂-TPD experiments. Among them, the first two species can be easily reduced by H₂ at temperature below 350 °C, while the last one can only be reduced by H₂ at temperature above 500 °C. The ignition temperatures of POM reaction over the catalysts are closely related to the temperature at which most of the RhO_x and RhⁱO_x species can be reduced by CH₄ in the reaction mixture. Compared to the Rh/Al₂O₃ with high Rh loadings, the catalysts with low Rh loadings contain more RhⁱO_x species which possess stronger RhO bond strength and are more difficult to be reduced than RhO_x by the reaction mixture. Higher temperature is therefore required to ignite the POM reaction over the catalysts with lower Rh loadings. The oscillation during the POM reaction over the Rh/Al₂O₃ with low Rh loadings can be related to the behaviour of Rh(AlO₂)_y species in the catalyst switching cyclically from the oxidized state to the reduced state during the reaction.     

Characteristics of La2O3 thin films deposited using metal organic chemical vapor deposition with different oxidant gas

La₂O₃ films were deposited using O₃ and the structural and electrical properties were investigated and compared with those of La₂O₃ films deposited using O₂. The deposition temperature of the La₂O₃ films using O₃ was slightly reduced compared to that of the La₂O₃ films generated using O₂. After a post-annealing process at 600 and 900 °C, the crystallinity of the La₂O₃ films using O₃ were smaller than that using O₂. The leakage current density increased after annealing at 600 °C due to densification and then decreased after annealing at 900 °C due to interfacial layer growth. The effective dielectric constant of the La₂O₃ films deposited using O₃ decreased at 900 °C due to interfacial layer growth. The La₂O₃ films deposited using O₃ showed better structural and electrical properties in this study.     

Formation of Y3Al5O12–Al2O3 eutectic microstructure with off-eutectic composition

Homogeneous-eutectic microstructure of Y₃Al₅O₁₂–Al₂O₃ system without coarse primary crystals was formed at an off-eutectic composition. This method utilizes a low migration rate in an amorphous phase. A mixture of Y₂O₃ and Al₂O₃ having the off-eutectic composition was melted and quenched rapidly to form an amorphous phase. A heat-treatment of the amorphous phase at 1000 °C and 1300 °C for 30 min formed Y₃Al₅O₁₂ and Al₂O₃ phases. SEM observation of this material, which was formed from the amorphous phase at 1300 °C for 30 min, showed homogeneous eutectic-like microstructure. The formation of the primary crystals (coarse Al₂O₃), which are always observed in the off-eutectic compositions by ordinary method, was completely suppressed.     

Quantification of the in situ DRIFT spectra of Pt/K/γ-A12O3 NOx adsorber catalysts

A method to quantify DRIFT spectral features associated with the in situ adsorption of gases on a NO_x adsorber catalyst, Pt/K/Al₂O₃, is described. To implement this method, the multicomponent catalyst is analysed with DRIFT and chemisorption to determine that under operating conditions the surface comprised a Pt phase, a pure γ-Al₂O₃ phase with associated hydroxyl groups at the surface, and an alkalized-Al₂O₃ phase where the surface –OH groups are replaced by –OK groups. Both DRIFTS and chemisorption experiments show that 93–97% of the potassium exists in this form. The phases have a fractional surface area of 1.1% for the 1.7 nm-sized Pt, 34% for pure Al₂O₃ and 65% for the alkalized-Al₂O₃. NO₂ and CO₂ chemisorption at 250 °C is implemented to determine the saturation uptake value, which is observed with DRIFTS at 250 °C. Pt/Al₂O₃ adsorbs 0.087 μmol CO₂/m²and 2.0 μmol NO₂/m², and Pt/K/Al₂O₃ adsorbs 2.0 μmol CO₂/m²and 6.4 μmol NO₂/m². This method can be implemented to quantitatively monitor the formation of carboxylates and nitrates on Pt/K/Al₂O₃ during both lean and rich periods of the NO_x adsorber catalyst cycle.