共查询到20条相似文献,搜索用时 15 毫秒
1.
L. Cai Y. Zhang X. Xiao J. Zhang G. Xu 《Energy Sources, Part A: Recovery, Utilization, and Environmental Effects》2016,38(2):190-201
A process model using Aspen Plus was established to simulate the performance of a lignite-fired 1,025 t/h circulating fluidized bed boiler integrated with a dryer and a pyrolyzer for improving the energy efficiency. The combustion module of the proposed model was first verified by design data and the system characteristics of the circulating fluidized bed boiler combined with the coal dryer and the pyrolyzer were then investigated. The most suitable case for the retrofit of existing 1,025 t/h CFB boilers is that 35% of the coal was dried and then pyrolyzed with the energy efficiency of 95.3% and exergy efficiency of 50.2%. The results demonstrate the lignite-fired circulating fluidized bed boiler integrated with a dryer and a pyrolyzer facilitates the system performances effectively. 相似文献
2.
循环流化床锅炉技术是目前迅速发展起来的一项高效、清洁燃烧技术。结焦就是循环流化床锅炉运行中较为常见的故障,它直接影响到锅炉的安全经济运行。结合循环流化床锅炉的运行特点,根据本人几年来的流化床锅炉调试和运行经验,分析流化床锅炉结焦的主要原因,并对如何预防循环流化床锅炉结焦进行了探讨。 相似文献
3.
4.
5.
6.
依托于日趋成熟的节能型循环流化床锅炉燃烧技术,开发国内容量最大的节能型循环流化床热水锅炉势在必行。介绍了168 MW节能型循环流化床热水锅炉设计思路、结构及性能特点。 相似文献
7.
基于流态重构的循环流化床锅炉节能燃烧技术的应用实践 总被引:1,自引:0,他引:1
针对循环流化床锅炉辅机电耗普遍偏高的问题,先后在燃烧劣质无烟煤的135 MW机组和300MW机组循环流化床锅炉上进行了降低床料存量实现流态重构的燃烧试验,分析了基于流态重构的循环流化床锅炉节能燃烧技术对改善锅炉机组性能的影响.运行实践表明:流态重构后,循环流化床锅炉辅机电耗明显下降,在风机具备变频条件下电耗可降低更多;135 MW机组锅炉运行厂用电率从8.2%降低为6.9%,300MW机组锅炉厂用电率约为4.3%,锅炉主要受热面的磨损明显减轻,飞灰可燃物含量降低3%~5%. 相似文献
8.
简述了生物质燃料特性、高低差速床内循环机制、秸杆积灰与腐蚀原理、V+4T技术概要。V+4T关键技术和控制工艺在高低差速床生物质锅炉的应用,解决了生物质锅炉存在的积灰与腐蚀难题。 相似文献
9.
复合床式低倍率循环流化床锅炉的研制开发 总被引:1,自引:0,他引:1
本文全面分析了较高循环倍率循环流化床锅炉所存在的技术问题,提出采用设计经验成熟、运行稳定可靠、热效率高、电耗低的低循环倍率循环流化床锅炉技术来实现循环流化床锅炉的大型化的新技术思想,并据此研制开发出复合床式低倍率循环流化床锅炉新技术。通过介绍和分析复合床式低倍率循环流化床锅炉的技术原理及技术特点,展示新炉型所具有的锅炉主要部件的灵活布置方式,为循环流化床锅炉的大型化指出了新的发展方向。 相似文献
10.
叙述了循环流化床锅炉的概况、影响循环流化床锅炉正常运行的因素、解决影响循环硫化锅炉正常运行的有效措施,分析了循环流化床锅炉运行中的常见问题。 相似文献
11.
12.
13.
具有收缩出口结构的新型循环流化床锅炉的试验研究 总被引:2,自引:0,他引:2
通过在冷态循环流化床模型上进行的大量试验研究,提出了强化循环流化床锅炉出口端头效应的方法,分析了收缩出口结构可以强化循环流化床锅炉出口端头效应的机理。结果表明:收缩出口结构的收缩度对循环流化床锅炉流动特性和传热特性的影响存在一个最佳值,一般最佳收缩度与循环流化床锅炉当量直径之比为0.5。这一新发现对循环流化床锅炉的设计和运行有着重要的意义。图9参5。 相似文献
14.
针对循环流化床锅炉运行中存在的相关问题及完善措施,叙述了影响循环流化床锅炉热效率的主要因素,提出,提高循环流化床锅炉热效率的主要方法。 相似文献
15.
16.
循环流化床锅炉中心筒变形脱落原因分析及改进 总被引:2,自引:0,他引:2
循环流化床旋风分离器中心筒工作在高温条件下,在热膨胀和冷收缩的过程中容易变形和脱落,分离效果受到极大的影响。对循环流化床锅炉中心筒常见故障和分离效果差的原因进行分析,提出中心筒的改造措施。 相似文献
17.
18.
A new kind of measuring method that may be used to measure high temperature circulating solid particles flux in a circulating
fluidized bed boiler is studied in this paper. The measuring method is founded on the principle of thermal equilibrium. A
series of cold tests and hot tests were carried to optimize the structure and collocation of water-cooling tubes and showed
that the method had the advantage of simple, accurate, reliable and good applicability for on-line usage in a circulating
fluidized bed boiler. 相似文献
19.