Investigation of forward flow distributed combustion for gas turbine application

New innovative advanced combustion design methodology for gas turbine applications is presented that is focused on the quest towards zero emissions. The new design methodology is called colorless distributed combustion (CDC) and is significantly different from the currently used methodology. In this paper forward flow modes of CDC have been investigated for application to gas turbine combustors. The CDC provides significant improvement in pattern factor, reduced NO_x emission and uniform thermal field in the entire combustion zone for it to be called as an isothermal reactor. Basic requirement for CDC is carefully tailored mixture preparation through good mixing between the combustion air and product gases prior to rapid mixing with fuel so that the reactants are at much higher temperature to result in hot and diluted oxidant stream at temperatures that are high enough to autoignite the fuel and oxidant mixture. With desirable conditions one can achieve spontaneous ignition of the fuel with distributed combustion reactions. Distributed reactions can also be achieved in premixed mode of operation with sufficient entrainment of burned gases and faster turbulent mixing between the reactants. In the present investigation forward flow modes consisting of two non-premixed combustion modes and one premixed combustion mode have been examined that provide potential for CDC. In all the configurations the air injection port is positioned at the opposite side of the combustor exit, whereas the location of fuel injection ports is changed to give different configurations. Two combustion geometries resulting in thermal intensity of 5 MW/m³-atm and 28 MW/m³-atm are investigated. Increase in thermal intensity (lower combustion volume) presents many challenges, such as, lower residence time, lower recirculation of gases and effect of confinement on jet characteristics. The results are presented on the global flame signatures, exhaust emissions, and radical emissions using experiments and flowfield using numerical simulations. Ultra-low NO_x emissions are found for both the premixed and non-premixed combustion modes at the two thermal intensities investigated here. Almost colorless flames (no visible flame signatures) have been observed for the premixed combustion mode. The reaction zone is observed to be significantly different in the two non-premixed modes. Higher thermal intensity case resulted in lower recirculation of gases within the combustion chamber and higher CO levels, possibly due to lower associated residence time. The characteristics at the two thermal intensity combustors investigated here were found to be similar.     

Effect of flow field for colorless distributed combustion (CDC) for gas turbine combustion

Colorless distributed combustion (CDC) investigated here is focused on gas turbine combustion applications due to its significant benefits for, much reduced NOx emissions and noise reduction, and significantly improved pattern factor. CDC is characterized by distributed reaction zone of combustion which leads to uniform thermal field and avoidance of hot spot regions to provide significant improvement in pattern factor, lower sound levels and reduced NOx emission. Mixing between the combustion air and product gases to form hot and diluted oxidant prior to its mixing with the fuel is critical so that one must determine the most suitable mixing conditions to minimize the ignition delay. Spontaneous ignition of the fuel occurs to provide distributed reaction combustion conditions. The above requirements can be met with different configuration of fuel and air injections with carefully characterized flow field distribution within the combustion zone. This study examines four different sample configurations to achieve colorless distributed combustion conditions that reveal no visible color of the flame. They include a baseline diffusion flame configuration and three other configurations that provide conditions close to distributed combustion conditions. For all four modes same fuel and air injection diameters are used to examine the effect of flow field configuration on combustion characteristics. The results are compared from the four different configurations on flow field and fuel/air mixing using numerical simulations and with experiments using global flame signatures, exhaust emissions, acoustic signatures, and thermal field. Both numerical simulations and experiments are performed at a constant heat load of 25 kW, using methane as the fuel at atmospheric pressure using normal temperature air and fuel. Lower NOx and CO emissions, better thermal field uniformity, and lower acoustic levels have been observed when the flame approached CDC mode as compared to the baseline case of a diffusion flame. The reaction zone is observed to be uniformly distributed over the entire combustor volume when the visible flame signatures approached CDC mode.     

Distributed swirl combustion for gas turbine application

Colorless distributed combustion (CDC) has been shown to provide significant improvement in gas turbine combustor performance. Colorless distributed combustion with swirl is investigated here to develop ultra-low emissions of NO and CO, and significantly improved pattern factor. Experimental investigations have been performed using a cylindrical geometry combustor with swirling air injection and axial hot gas exit stream from the combustor. Air was injected tangentially to impart swirl to the flow inside the combustor. The results obtained from the combustor have demonstrated very low levels of NO (∼3 PPM) and CO (∼70 PPM) emissions at an equivalence ratio of 0.7 and a high heat release intensity of 36 MW/m³-atm under non-premixed combustion. To further simulate gas turbine operating conditions, inlet air to the combustor was preheated to 600 K temperature and the combustor operated at 2 atm pressure. Results showed very low levels of CO (∼10 PPM) but the NO increased somewhat to ∼10 PPM at an equivalence ratio of 0.5 and heat release intensity of 22.5 MW/m³-atm under non-premixed combustion conditions. For premixed combustion, the combustor demonstrated low levels of both NO (5 PPM) and CO (8 PPM) at an equivalence ratio of 0.6 and a heat release intensity of 27 MW/m³-atm. Results are reported at different equivalence ratios on the emission of NO and CO, lean stability limit and OH^* chemiluminescence. These results suggest that further performance improvement can be achieved with improved fuel mixture preparation prior to the ignition of fuel at higher operational pressures using swirling combustor design for our quest to develop ultra low emission high intensity combustor for gas turbine application.     

Swirling distributed combustion for clean energy conversion in gas turbine applications

Distributed combustion provides significant performance improvement of gas turbine combustors. Key features of distributed combustion includes uniform thermal field in the entire combustion chamber, thus avoiding hot-spot regions that promote NO_x emissions (from thermal NO_x) and significantly improved pattern factor. Rapid mixing between the injected fuel and hot oxidizer has been carefully explored for spontaneous ignition of the mixture to achieve distributed combustion reactions. Distributed reactions can be achieved in premixed, partially premixed or non-premixed modes of combustor operation with sufficient entrainment of hot and active species present in the flame and their rapid turbulent mixing with the reactants. Distributed combustion with swirl is investigated here for our quest to explore the beneficial aspects of such flows on clean combustion in simulated gas turbine combustion conditions. The goal is to develop high intensity combustor with ultra low emissions of NO and CO, and much improved pattern factor. Experimental results are reported from a cylindrical geometry combustor with different modes of fuel injection and gas exit stream location in the combustor. In all the configurations, air was injected tangentially to impart swirl to the flow inside the combustor. Ultra-low NO_x emissions were found for both the premixed and non-premixed combustion modes for the geometries investigated here. Swirling flow configuration, wherein the product gas exits axially resulted in characteristics closest to premixed combustion mode. Change in fuel injection location resulted in changing the combustion characteristics from traditional diffusion mode to distributed combustion regime. Results showed very low levels of NO (∼3 PPM) and CO (∼70 PPM) emissions even at rather high equivalence ratio of 0.7 at a high heat release intensity of 36 MW/m³-atm with non-premixed mode of combustion. Results are also reported on lean stability limit and OH^* chemiluminescence under both premixed and non-premixed conditions for determining the extent of distribution combustion conditions.     

Development of high intensity CDC combustor for gas turbine engines

Colorless distributed combustion (CDC) has been demonstrated to provide ultra-low emission of NOx and CO, improved pattern factor and reduced combustion noise in high intensity gas turbine combustors. The key feature to achieve CDC is the controlled flow distribution, reduce ignition delay, and high speed injection of air and fuel jets and their controlled mixing to promote distributed reaction zone in the entire combustion volume without any flame stabilizer. Large gas recirculation and high turbulent mixing rates are desirable to achieve distributed reactions thus avoiding hot spot zones in the flame. The high temperature air combustion (HiTAC) technology has been successfully demonstrated in industrial furnaces which inherently possess low heat release intensity. However, gas turbine combustors operate at high heat release intensity and this result in many challenges for combustor design, which include lower residence time, high flow velocity and difficulty to contain the flame within a given volume. The focus here is on colorless distributed combustion for stationary gas turbine applications. In the first part of investigation effect of fuel injection diameter and air injection diameter is investigated in detail to elucidate the effect fuel/air mixing and gas recirculation on characteristics of CDC at relatively lower heat release intensity of 5 MW/m³ atm. Based on favorable conditions at lower heat release intensity the effect of confinement size (reduction in combustor volume at same heat load) is investigated to examine heat release intensity up to 40 MW/m³ atm. Three confinement sizes with same length and different diameters resulting in heat release intensity of 20 MW/m³ atm, 30 MW/m³ atm and 40 MW/m³ atm have been investigated. Both non-premixed and premixed modes were examined for the range of heat release intensities. The heat load for the combustor was 25 kW with methane fuel. The air and fuel injection temperature was at normal 300 K. The combustor was operated at 1 atm pressure. The results were evaluated for flow field, fuel/air mixing and gas recirculation from numerical simulations and global flame images, and emissions of NO, CO from experiments. It was observed that the larger air injection diameter resulted in significantly higher levels of NO and CO whereas increase in fuel injection diameter had minimal effect on the NO and resulted in small increase of CO emissions. Increase in heat release intensity had minimal effect on NO emissions, however it resulted in significantly higher CO emissions. The premixed combustion mode resulted in ultra-low NO levels (<1 ppm) and NO emission as low as 5 ppm was obtained with the non-premixed flame mode.     

Spatially distributed flame transfer functions for predicting combustion dynamics in lean premixed gas turbine combustors

The present paper describes a methodology to improve the accuracy of prediction of the eigenfrequencies and growth rates of self-induced instabilities and demonstrates its application to a laboratory-scale, swirl-stabilized, lean-premixed, gas turbine combustor. The influence of the spatial heat release distribution is accounted for using local flame transfer function (FTF) measurements. The two-microphone technique and CH^∗ chemiluminescence intensity measurements are used to determine the input (inlet velocity perturbation) and the output functions (heat release oscillation), respectively, for the local flame transfer functions. The experimentally determined local flame transfer functions are superposed using the flame transfer function superposition principle, and the result is incorporated into an analytic thermoacoustic model, in order to predict the linear stability characteristics of a given system. Results show that when the flame length is not acoustically compact the model prediction calculated using the local flame transfer functions is better than the prediction made using the global flame transfer function. In the case of a flame in the compact flame regime, accurate predictions of eigenfrequencies and growth rates can be obtained using the global flame transfer function. It was also found that the general response characteristics of the local FTF (gain and phase) are qualitatively the same as those of the global FTF.     

Increasing the power output of hydrogen internal combustion engines by means of supercharging and exhaust gas recirculation

Spark ignition engines can be relatively easily converted to hydrogen using port fuel injection (PFI). However, because of the lower volumetric energy density of a hydrogen–air mixture and the occurrence of abnormal combustion phenomena such as backfire, hydrogen-fueled PFI engines suffer from a power deficit in comparison with gasoline engines. This paper reports measurements on a single-cylinder hydrogen engine equipped with a supercharger and an exhaust gas recirculation (EGR) system. Using EGR combined with supercharging and a three-way catalyst (TWC) is shown to significantly increase the power output while limiting tailpipe emissions of oxides of nitrogen (NO_x).     

燃气轮机燃烧室三维冷态流场数值模拟

本文针对某燃气轮机环管型燃烧室三维冷态流场的数值模拟问题进行了研究。根据该型燃气轮机燃烧室的设计图纸建立真实的三维计算几何模型;在计算中采用SIMPLE算法,k-ε双方程湍流模型,对其进行了冷态空气流场的数值模拟;通过对各处流场分布的分析,特别是对主要区域各关键截面的流动分析,可以判断出燃烧室设计的合理性,为进一步优化燃烧室的结构设计、改善流场结构,并为开展燃烧室热态流场的数值模拟奠定了基础。     

Heat release rate markers for premixed combustion

The validity of the commonly used flame marker for heat release rate (HRR) visualization, namely the rate of the reaction OH + CH₂O ⇔ HCO + H₂O is re-examined. This is done both for methane–air and multi-component fuel–air mixtures for lean and stoichiometric conditions. Two different methods are used to identify HRR correlations, and it is found that HRR correlations vary strongly with stoichiometry. For the methane mixture there exist alternative HRR markers, while for the multi-component fuel flame the above correlation is found to be inadequate. Alternative markers for the HRR visualization are thus proposed and their performance under turbulent conditions is evaluated using DNS data.     

Hydrogen enrichment of methane and syngas for MILD combustion

Moderate or Intense Low-oxygen Dilution (MILD) combustion is a technology with important characteristics such as significant low emission and high-efficiency combustion. The hydrogen enrichment of conventional fuels is also of interest due to its favorable characteristics, such as low carbon-containing pollutants, high reaction intensity, high flammability, and thus fuel usage flexibility. In this study, the effects of adding hydrogen to methane and syngas fuels have been investigated under conditions of MILD combustion through numerical simulation of a well-set-up MILD burner. The Reynolds-Averaged Navier-Stokes (RANS) approach is adopted along the Eddy Dissipation Concept (EDC) combustion model with two different chemical mechanisms. Molecular diffusion is modeled using the differential diffusion approach. The effects of oxidizer dilution and fuel jet Reynolds number on the reactive flow field have been studied. Results show that with an increase in hydrogen portion of the fuel mixtures, the volume of the high-temperature region of combustion field increases whereas a reduction of oxidizer oxygen content leads to more proximity to the MILD condition. Increasing the fuel jet Reynolds number will result in an expansion of the combustion zone and shifting of this region in the axial direction. Predictions revealed that the methane flame is more sensitive to the oxidizer dilution and fuel jet Reynolds number than syngas. Moreover, enrichment of fuel with hydrogen seems to be better for acquiring condition of the MILD combustion for syngas rather than methane. Indeed, syngas shows more sensitivity to hydrogen enrichment than methane, which makes hydrogen a good additive to syngas in terms of MILD condition benefits.     

Study of flow and combustion characteristics of optimized low swirl premixed nozzle for micro gas turbine

With the micro gas turbine is used more and more widely, the operating conditions become complex and fluctuating which impacts the environmental friendliness of combustor. In this work, a low swirl premixed nozzle (LSPN) is designed based on the original premixed nozzle (OPN) of a 60 kW micro gas turbine, in order to adapt the flexibility of load and operating environment by improving the mixing performance of fuel and air. The flow and combustion characteristics of LSPN and OPN fed by natural gas is numerically studied using the standard k-ε model and the combined Finite Rate Chemistry/Eddy Dissipation Model (FRC/EDM) under various operating conditions. The results show that the mixing performance of air and fuel in LSPN has been improved. The flow unmixedness in LSPN is always smaller than OPN, and it is 41.74% lower at the outlet of the nozzle. While the equivalence ratio decreases, the mean temperature in the combustor decline. Furthermore, under the majority of operating conditions, the emission performance of LSPN is better than OPN.     

旋流器流量分配对燃气轮机燃烧性能的影响研究

目前锅炉燃烧控制主要依靠人工手动调整,为解决运行经验差异导致锅炉燃烧性能差异的问题,提出了一种基于动态标杆值的电站锅炉燃烧控制优化方法。在建立燃烧模型的基础上,以归一化经济与环保指标得到综合效益因子作为寻优判据,对历史工况进行数据挖掘,实现全工况下基于动态标杆值的运行参数自主寻优和更新,使锅炉燃烧、污染物排放相互协调。该方法已于某燃煤电站成功实践,结果表明：在应用案例中,寻优推送后综合效益因子提高了4.34%,使得锅炉热效率和NOx排放质量浓度相互协调更优。     

Combustion behavior and stability map of hydrogen-enriched oxy-methane premixed flames in a model gas turbine combustor

The article describes an experimental study and comparison of the combustion behavior and determines the stability map of turbulent premixed H₂-enriched oxy-methane flames in a model gas turbine combustor. Static stability limits, in terms of flashback and blow-out limits, are recorded over a range of hydrogen fraction (HF) at a fixed oxygen fraction (OF) of 30% and a particular inlet bulk velocity, and the results are compared with the non-enriched case (HF = 0%). The static stability limits are also recorded for different inlet bulk velocity (4.4, 5.2, and 6 m/s) and the results are compared to explore the effect of flow dynamics on operability limits of H₂-enriched flames. The stability maps are presented as a function of equivalence ratio (0.3–1.0) and HF (0%–75%) plotted on the contours of adiabatic flame temperature (AFT), power density (PD), inlet Reynolds number (Re) and reacting mixture mass flow rate ($\dot{m}$) to understand the physics behind flashback and blow-out phenomena. The results indicated that both the flashback and blow-out limits tend to move towards the leaner side with increasing HF due to the improved chemical kinetics. The stability limits are observed to follow the Reynolds number indicating its key role in controlling flame static stability limits. The results showed that H₂ enrichment is effective in the zone from HF = 20% up to HF = 50%, and O₂ enrichment is also effective in a similar zone from OF = 20% up to 50%, with wider stability boundaries for H₂ enrichment. Axial and radial temperature profiles are presented to explore the effect of HF on the progress of chemical reactions within the combustor and to serve as the basis for validation of numerical models. Flame shapes are recorded using a high-speed camera and compared for different inlet velocities to explore the effects of H₂-enrichment and equivalence ratio on flame stability. The equivalence ratio at which a transition of flame stabilization from the inner shear layer (ISL) to the outer recirculation zone (ORZ) occurs is determined for different inlet bulk velocities. The value of the transition equivalence ratio is found to decrease while increasing the inlet bulk velocity. Flame shapes near flashback limit, as well as near blow-out limit, are compared to explore the mechanisms of flame extinctions. Flame shapes are compared at fixed adiabatic flame temperature, fixed inlet velocity and fixed flow swirl to isolate their effects and investigate the effect of kinetic rates on flame stability. The results showed that the adiabatic flame temperature does not govern the flame static stability limits.     

Large Eddy Simulations of gaseous flames in gas turbine combustion chambers

Recent developments in numerical schemes, turbulent combustion models and the regular increase of computing power allow Large Eddy Simulation (LES) to be applied to real industrial burners. In this paper, two types of LES in complex geometry combustors and of specific interest for aeronautical gas turbine burners are reviewed: (1) laboratory-scale combustors, without compressor or turbine, in which advanced measurements are possible and (2) combustion chambers of existing engines operated in realistic operating conditions. Laboratory-scale burners are designed to assess modeling and fundamental flow aspects in controlled configurations. They are necessary to gauge LES strategies and identify potential limitations. In specific circumstances, they even offer near model-free or DNS-like LES computations. LES in real engines illustrate the potential of the approach in the context of industrial burners but are more difficult to validate due to the limited set of available measurements. Usual approaches for turbulence and combustion sub-grid models including chemistry modeling are first recalled. Limiting cases and range of validity of the models are specifically recalled before a discussion on the numerical breakthrough which have allowed LES to be applied to these complex cases. Specific issues linked to real gas turbine chambers are discussed: multi-perforation, complex acoustic impedances at inlet and outlet, annular chambers…. Examples are provided for mean flow predictions (velocity, temperature and species) as well as unsteady mechanisms (quenching, ignition, combustion instabilities). Finally, potential perspectives are proposed to further improve the use of LES for real gas turbine combustor designs.     

燃气轮机燃烧室内部流场的冷态模拟与优化设计

利用流体分析软件STAR-CD对一个燃气轮机燃烧室的内部流场完整真实的几何结构进行了三维的冷态模拟；得出其内部的流场分布，对其加以分析，找出原设计中存在的问题，并加以改进，得出更加合理的流场分布，从而指导燃烧室的结构设计。改进后的数值模拟结果表明，改进措施的效果是十分明显的，所建立的流动分析系统为燃气轮机燃烧室的优化设计提供了强有力的计算分析工具。     

An evaluation of detailed reaction mechanisms for hydrogen combustion under gas turbine conditions

Chemical kinetics in hydrogen combustion for elevated pressures have recently become more relevant because of the implementation of hydrogen as a fuel in future gas turbine combustion applications, such as IGCC or IRCC systems. The aim of this study is to identify a reaction mechanism that accurately represents H₂/O₂ kinetics over a large range of conditions, particularly at elevated pressures as present in a gas turbine combustor. Based on a literature review, six mechanisms of different research groups have been selected for further comparisons within this study. Reactor calculations of ignition delay times show that the mechanisms of Li et al. and Ó Conaire et al. yield the best agreement with data from shock tube experiments at pressures up to 33 bar. The investigation of one-dimensional laminar hydrogen flames indicate that these two mechanisms also yield the best agreement with experimental data of laminar flame speed, particularly for elevated pressures. The present study suggests that the Li mechanism is best suited for the prediction of H₂/O₂ chemistry since it includes more up-to date data for the range of interest.     

Reduction of a detailed reaction mechanism for hydrogen combustion under gas turbine conditions

The aim of this study is to find a reduced mechanism that accurately represents chemical kinetics for lean hydrogen combustion at elevated pressures, as present in a typical gas turbine combustor. Calculations of autoignition, extinction, and laminar premixed flames are used to identify the most relevant species and reactions and to compare the results of several reduced mechanisms with those of a detailed reaction mechanism. The investigations show that the species OH and H are generally the radicals with the highest concentrations, followed by the O radical. However, the accumulation of the radical pool in autoignition is dominated by HO₂ for temperatures above, and by H₂O₂ below the crossover temperature. The influence of H₂O₂ reactions is negligible for laminar flames and extinction, but becomes significant for autoignition. At least 11 elementary reactions are necessary for a satisfactory prediction of the processes of ignition, extinction, and laminar flame propagation under gas turbine conditions. A 4-step reduced mechanism using steady-state approximations for HO₂ and H₂O₂ yields good results for laminar flame speed and extinction limits, but fails to predict ignition delay at low temperatures. A further reduction to three steps using a steady-state approximation for O leads to significant errors in the prediction of the laminar flame speed and extinction limit.     

Simulation of producer gas flameless combustion with fresh reactant diluted by hot flue gas

Flameless combustion is considered as a flexible and efficient combustion process for low heating value gas fuel. This paper presents numerical simulations of premixed flameless combustion using producer gas as a fuel. Different initial conditions of the premixed fresh reactant (air/fuel mixture) and dilution levels are taken into account for the investigation. The numerical simulations were investigated using a network of chemical reactor models with the detailed reaction mechanism of GRI‐Mech 3.0. A threshold dilution level for flameless combustion fuelled by producer gas was determined. The numerical results show that dilution of the fresh reactant with hot combustion products and initial fresh reactant temperature play important roles in flameless combustion formation and its auto‐ignition behaviour, rather than equivalence ratio of the fresh reactant. In the flameless combustion regime, temperature and chemical concentrations were reduced while chemical kinetics process was decelerated, resulting in delay of the auto‐ignition process.     

9F型燃机多通道燃烧动态压力监测系统研究

干式低NOx燃烧技术(DLN)能降低燃气轮机NOx排放.燃烧稳定性监测是进行干式低NOx燃烧调整的基础,而燃烧压力脉动则是反映燃烧稳定性的重要参数.研制了适用于GE公司9F型燃机的多通道燃烧动态压力监测系统,包括动态压力传感器、数据采集卡以及分析软件.现场试验显示,该系统能在线采集燃机燃烧室内多通道的压力脉动,与电厂安装的便携式动态压力监测系统(CDMS)数据进行对比,两者都在频率94、138、217、302 Hz附近存在峰值.该系统为9F型燃机进行DLN燃烧调整提供了真实、可靠的数据支持.     

MILD combustion for hydrogen and syngas at elevated pressures

As gas recirculation constitutes a fundamental condition for the realization of MILD combustion, it is necessary to determine gas recirculation ratio before designing MILD combustor. MILD combustion model with gas recir- culation was used in this simulation work to evaluate the effect of fuel type and pressure on threshold gas recir- culation ratio of MILD mode. Ignition delay time is also an important design parameter for gas turbine combustor, this parameter is kinetically studied to analyze the effect of pressure on MILD mixture ignition. Threshold gas re- circulation ratio of hydrogen MILD combustion changes slightly and is nearly equal to that of 10 MJ/Nm3 syngas in the pressure range of 1-19 atm, under the conditions of 298 K fresh reactant temperature and 1373 K exhaust gas temperature, indicating that MILD regime is fuel flexible. Ignition delay calculation results show that pres- sure has a negative effect on ignition delay time of 10 MJ/Nm3 syngas MILD mixture, because OH mole fraction in MILD mixture drops down as pressure increases, resulting in the delay of the oxidation process.