共查询到19条相似文献,搜索用时 125 毫秒
1.
2.
3.
4.
通过连铸坯低倍腐蚀评估铸坯中心偏析、中心疏松等铸坯内部缺陷,反馈铸坯内部质量。从铸机辊缝、动态轻压下、喷嘴、钢水过热度、化学成分等方面研究铸坯内部质量的影响因素和控制措施。工艺优化后连铸低倍合格率上升8.17个百分点,提高了1#连铸机的内部质量。 相似文献
5.
6.
在用220mm^2的连铸机连铸GCr15轴承钢方坯的基础工艺上,通过调整连铸时钢水过热度、拉速、二冷配水、电磁搅拌的参数来减少连铸轴承钢大方坯的中心碳偏析及中心疏松等低倍组织缺陷,从而提高GCr15轴承钢方坯的质量。 相似文献
7.
8.
高碳钢连铸坯的质量受拉速、二冷比水量、钢水过热度的影响较大。本文以SWRH382B预应力钢铸坯为研究对象,研究了拉速、二冷比水量、钢水过热度三个连铸参数对铸坯中心碳偏析的影响,从而得出了最佳的连铸工艺。 相似文献
9.
分析帘线钢连铸过程中中心偏析的形成原理及对铸坯质量的影响。研究帘线钢连铸坯中心偏析的控制措施,包括连铸拉速与钢水温度优化控制、结晶器电磁搅拌、凝固末端轻压下、二冷动态控制等核心工艺技术。通过应用这些技术,帘线钢WLX72A和WLX82A连铸坯平均中心碳偏析指数分别控制在1.042和1.027,综合合格率达到99.97%。 相似文献
10.
本文讨论了连铸GCr15轴承钢过程中,通过控制好合适的中间包过热度和拉速之间的关系,以及选择合适的电磁搅拌的工艺参数,能够取得较好的GCr15轴承钢的低倍组织和有效控制铸坯的中心碳偏析。 相似文献
11.
Effects of continuous casting process parameters on carbon segregation degree of 38CrMoAl steel big round billet 总被引:2,自引:0,他引:2
The effects of continuous casting process parameters (superheat degree, casting speed and F- EMS) on the carbon segregation of round billet with diameter 600mm of 38CrMoAl steel were investigated by industrial experiments and numerical simulations. The results show that the equiaxed crystal rate and solidification structure both affect the carbon segregation. When the superheat is low, shrinkage tends to occur, and the shrinkage is often accompanied by severe segregation. When the superheat is high, the equiaxed grain ratio is lower, carbon segregation is also severer, so the superheat degree is controlled at 30??. With the increasing of casting speed?? it can obviously spur the growth of columnar crystals and formation of central pipe; both columnar crystals and central pipe are the major cause of segregation, so the suitable casting speed is 0. 19m/min. Final electromagnetic stirring has the effect of uniform liquid steel composition and temperature, which increases the density of solidification structure, and reduces the central shrinkage hole, thereby reducing carbon segregation, but the electromagnetic stirring effect is greatly affected by the installation position. Based on comprehensive consideration of the production and quality in practical production, the suitable process parameters are established: the optimal superheat is 30??, casting speed is 0. 28m/min, the combination of electromagnetic stirring is M- EMS+S- EMS+F- EMS, and the corresponding electromagnetic stirring parameters are M- EMS of 101A/2Hz??S- EMS of 200A/8Hz??F- ME of 900A/8Hz. Under the above process conditions, it will be more reasonable for the F- EMS installation position to move 0. 4-0. 5m toward the meniscus. 相似文献
12.
通过对铸坯的低倍检验和中间裂纹部位的电镜扫描,分析了连铸板坯中间裂纹的位置和成因,提出了从钢水成分、二冷配水、铸机设备状况、钢水过热度、拉速等方面的改进措施,使连铸坯中间裂纹的发生率和级别大幅度下降。 相似文献
13.
阐述了在武钢第一炼钢厂条件下生产高碳钢时浇铸温度的控制措施。通过改善钢包、中包的保温效果,并采用合理的LF炉温度控制模式,可以使得高碳钢在进行低拉速浇铸时获得稳定且较低的过热度.从而有效降低铸坯碳偏析。 相似文献
14.
摘要:基于国内某厂高碳钢小方坯连铸生产过程,首先利用ProCAST软件进行过热度对连铸坯宏观偏析影响的模拟研究,然后对过热度分别为44、39和28℃的连铸坯横断面和纵截面进行宏观偏析和疏松缩孔的研究。模拟结果表明:连铸坯横断面中心碳偏析随着过热度的增加不断增大,过热度超过25℃时,连铸坯横断面中心碳偏析度更加严重;试验结果表明,过热度分别为44、39和28℃ 的连铸坯横断面中心碳最大偏析度分别为1.39、1.32和1.06。结合模拟结果能够有效指导实际生产过程中连铸参数的调整,过热度越高,连铸坯中心碳偏析、条带状疏松缩孔越严重,为了降低连铸坯宏观偏析,建议将过热度控制在25~30℃。 相似文献
15.
16.
17.
基于国内某厂齿轮钢小方坯连铸生产过程,利用ProCAST软件建立移动切片模型,能够高效模拟连铸过程中的宏观偏析,模型分别模拟研究了不同过热度、二冷水量和拉坯速度等对宏观偏析的影响。模拟结果与碳偏析检测结果吻合良好,验证了移动切片模型模拟连铸坯宏观偏析的准确性。由于溶质浮力的影响,内弧侧的宏观偏析强于外弧侧。随着过热度的增加,铸坯中心碳偏析度从1.06增加至1.15。过热度控制在25 ℃范围内,可以保证铸坯的宏观碳偏析度控制在1.10范围内。随着连铸二冷水量的增加,铸坯中心偏析改善程度较小,铸坯中心碳偏析度从1.16降低至1.13。随着拉坯速度的增加,铸坯中心偏析呈现加重的趋势,铸坯中心碳偏析度由1.14增加至1.21,拉坯速度控制在1.4 m·min–1范围内,可保证铸坯中心碳偏析度低于1.15。 相似文献
18.
19.
通过大量的现场取样,结合实验室研究手段,系统的研究钢水过热度、拉速、二次冷却强度等工艺参数对高碳连铸坯中心偏析的影响,从而得出最佳的生产参数控制范围,改善swRH82B高碳钢连铸坯的中心偏析,提高铸坯质量和加工性能。 相似文献