Gradient thermal cycling behavior of a thermal barrier coating system constituted by NiCoCrAlY bond coat and pure metastable tetragonal nano-4YSZ top coat

Pure metastable tetragonal (t’) phase 4YSZ top coats with thickness of 100 and 200 μm were deposited on NiCoCrAlY-coated second generation single crystal superalloy by air plasma spray (APS). The two thermal barrier coatings were evaluated under gradient thermal cycling test using gas mixture of propane and oxygen. After flame shock test, the values of Young's modulus, hardness and degree of densification all exhibited a gradient distribution across YSZ thickness. In contrast to intensive sintering at surface of 200 μm 4YSZ coating, the TBC sample with 4YSZ layer of 100 μm underwent poor oxidation at interface of YSZ and bond coat, forming a duplex oxide scale: (Ni,Co)(Cr,Al)₂O₄ spinel over Al₂O₃, which promoted the delamination at the top-coat/bond-coat interface. The resistance against gradient thermal cycling, the phase stability of 4YSZ and the failure mechanism of the TBCs, were discussed correlating to the effects of YSZ thickness.     

Thermal aging behavior of plasma sprayed LaMgAl11O19 thermal barrier coating

The crystallization behavior of the amorphous phase of the plasma sprayed LaMgAl₁₁O₁₉ (LaMA) coating during thermal aging processes has been investigated. Results indicate that LaMA coating exhibits much similar microstructure and thermal properties such as close coefficient of thermal expansion and specific heat capacity etc. to the sintered LaMA bulk after aging at 1673 K for 20 h. On the other hand, a solid state reaction seems to occur to reform the ideal magnetoplumbite-type LaMA phase coupled with the formations of the La-rich aluminate intermediate phases. When the aging temperature is held between 1273 K and 1473 K, nanosized platelet-like grains as well as sub-grains with high aspect ratios are present. The phase stability has been investigated through the chemical compositions and X-ray diffraction analysis. The recrystallization mechanism of the amorphous LaMA coating has been explored by tracing the microstructure evolutions during thermal aging process.     

The effect of magnesium compounds (MgO and MgAl2O4) on the synthesis of Lanthanum magnesium hexaaluminate (LaMgAl11O19) by solid-state reaction method

In the present study, the lanthanum magnesium hexaaluminate (LaMgAl₁₁O₁₉)(LaMA) powder was synthesized by the solid–state reaction method using two types of magnesium compounds, including magnesium oxide (MgO) and magnesium aluminate (MgAl₂O₄) spinel (MAS). The effect of substitution of magnesium oxide with MAS on the synthesis temperature, intermediate compounds and morphology of synthesized powders were investigated. The microstructural results showed that the intermediate compounds of lanthanum aluminate (LaAlO₃), aluminum oxide and MAS were formed in the presence of magnesium oxide, whereas in the latter case, the LaAlO₃ intermediate phase was not observed and La₄Al₂MgO₁₀ was formed at about 810 °C. Also in both cases, a single LaMA phase with the platelet-like morphology was formed. The thickness of the LaMA platelets decreased from 300 nm to 125 nm and the synthesis temperature increased from 1330 °C to 1355 °C, by replacing MgO with MAS.     

Superposed structure of double-ceramic layer based on YSZ/LaMgAl11O19 thermal barrier coating

The superposed structure of double ceramic layer (SDCL) could be an effective means to develop long-life thermal barrier coating (TBC) at high temperatures. In this study, YSZ/LaMgAl₁₁O₁₉ TBC system with double-ceramic layer (DCL) and SDCL structures were prepared on nickel-based superalloy substrates by atmospheric plasma spraying. The thermal cycling behavior of the coatings was investigated using a furnace at 1000 °C and burner-rig facility at 1375 ± 25 °C on the coating surface. Results showed that the thermal cycle life of the SDCL structure was increased by 7.2% for the furnace and 13.2% for the burner-rig facility compared with that of the DCL structure. The relatively long thermal cycle life of the SDCL structure was attributed to the blocking of the propagation of cracks in the LMA layers by the YSZ ceramic layer and the release of residual thermal stresses by the formation of cracks in the LMA layers.     

Evaluation of hot corrosion behavior of plasma sprayed ceria and yttria stabilized zirconia thermal barrier coatings in the presence of Na2SO4+V2O5 molten salt

In this study, substrates of Inconel 738 LC superalloy coupons were first sprayed with a NiCoCrAlY bondcoat and then with a ceria and yttria stabilized zirconia (CYSZ; ZrO₂−25 wt%CeO₂−2.5 wt%Y₂O₃) topcoat by air plasma spraying (APS). Hot corrosion studies of plasma sprayed thermal barrier coatings (TBCs) were conducted in 45 wt%Na₂SO₄+55 wt%V₂O₅ molten salt at 1000 °C for 30 h. The results showed that the coating defects, such as pores and microcracks play important roles as effective paths for the salt penetration in hot corrosion. Based on the results, the reaction between molten salt and stabilizers of zirconia (Y₂O₃ and CeO₂), the formation of YVO₄, CeVO₄ and CeO₂ crystals, the detrimental phase transformation of zirconia from tetragonal to monoclinic due to the depletion of stabilizers and finally, the creation of stresses were recognized to be in the degradation mechanism of CYSZ ceramic coatings in the presence of molten sulfate–vanadate salt.     

Local residual stress evolution of highly irregular thermally grown oxide layer in thermal barrier coatings

Local residual stress in thermally grown oxide (TGO) layers is the primary cause of failure of thermal barrier coating (TBC) systems, especially TBCs prepared by air plasma spray (APS) with a highly irregular TGO. Herein, the distribution of residual stress and the evolution of the irregular TGO layer in APS TBCs were investigated as a function of oxidation time. The stress was measured from cross-sectional micrographs and converted to the actual stress inside the coatings before sectioning. The TGO exhibited significant inhomogeneity at different locations. Stress conversion occurred across the TGO thickness; the layer near the yttria-stabilised zirconia (YSZ) component exhibited compressive stress, whereas that along the bond coat was under tensile stress. The evolution of the compressive stress is also discussed. These analyses may provide a better understanding of the mechanism of APS TBCs.     

Failure mechanisms in model thermal and environmental barrier coating systems

The durability of environmental barrier coating (EBC) systems in gas turbine engine environments depends upon their temperature dependent rates of degradation by processes such as steam volatilization and bond coat oxidation. While addition of a thermal barrier coating (TBC) reduces the temperature within the EBC system, it introduces new failure mechanisms. Deposition of a segmented HfO₂ TBC with a reduced in-plane Young’s modulus is essential to avoid bifurcated TBC channel cracking into a Yb₂Si₂O₇ EBC, and delamination, as a result of an approximately 50% difference in coefficients of thermal expansion (CTE) of the coating layers. During prolonged high temperature steam cycling, a thin fluorite phase reaction layer is observed to develop at the HfO₂-YbDS interface consistent with recent thermochemical assessments. The CTE of the fluorite phase is shown to be substantially higher than that of either of the layers to which it is bonded, resulting in tunnel cracking of the fluorite, and eventual coating delamination of the TBC at either the fluorite-HfO₂ or YbDS-fluorite interfaces upon cooling. The study highlights the importance of matching the CTEs of the TBC and EBC layers during coating system design, and those of the reaction products that may form between them.     

Thermal cycling and hot corrosion behavior of a novel LaPO4/YSZ double-ceramic-layer thermal barrier coating

LaPO₄ powders were produced by a chemical co-precipitation and calcination method. The ceramic exhibited a monazite structure, kept phase stability at 1400?°C for 100?h, and had low thermal conductivity (~ 1.41?W/m?K, 1000?°C). LaPO₄/Y₂O₃ partially stabilized ZrO₂ (LaPO₄/YSZ) double-ceramic-layer (DCL) thermal barrier coatings (TBCs) were fabricated by air plasma spray. The LaPO₄ coating contained many nanozones. Thermal cycling tests indicated that the spallation of LaPO₄/YSZ DCL TBCs initially occurred in the LaPO₄ coating. The failure mode was similar to those of many newly developed TBCs, probably due to the low toughness of the ceramics. LaPO₄/YSZ DCL TBCs were highly resistant to V₂O₅ corrosion. Exposed to V₂O₅ at 700–900?°C for 4?h, La(P,V)O₄ formed as the corrosion product, which had little detrimental effect on the coating microstructure. At 1000?°C for 4?h, a minor amount of LaVO₄ was generated.     

Present status and future prospects of plasma sprayed multilayered thermal barrier coating systems

Thermal barrier coatings (TBCs) play a pivotal role in protecting the hot structures of modern turbine engines in aerospace as well as utility applications. To meet the increasing efficiency of gas turbine technology, worldwide research is focused on designing new architecture of TBCs. These TBCs are mainly fabricated by atmospheric plasma spraying (APS) as it is more economical over the electron beam physical vapor deposition (EB-PVD) technology. Notably, bi-layered, multi-layered and functionally graded TBC structures are recognized as favorable designs to obtain adequate coating performance and durability. In this regard, an attempt has been made in this article to highlight the structure, characteristics, limitations and future prospects of bi-layered, multi-layered and functionally graded TBC systems fabricated using plasma spraying and its allied techniques like suspension plasma spray (SPS), solution precursor plasma spray (SPPS) and plasma spray –physical vapor deposition (PS-PVD).     

Microstructural evaluation and thermal oxidation behaviors of YSZ/NiCoCrAlYTa coatings deposited by different thermal techniques

In this paper, two coating techniques, the high velocity oxy-fuel (HVOF) and air plasma spray (APS) techniques, were used to deposit a bond coat of NiCoCrAlYTa on the Inconel 625 substrate, followed by applying a topcoat of yttria-stabilized zirconia (YSZ). The samples were preoxidized in an argon-controlled furnace at a temperature of 1000 °C for 12 and 24 h to characterize the microstructure of a thermally grown oxide (TGO) using the two coating techniques. The most suitable preoxidized samples were further tested for isothermal oxidation at 1000 °C for up to 120 h, and a hot corrosion test was performed at 1000 °C for up to 52 h or until spalling occurred. As-sprayed and oxidized samples prepared with different coating techniques were evaluated in terms of their microstructure using different characterization methods, such as field emission scanning electron microscopy (FESEM), variable pressure scanning electron microscopy (VPSEM), energy dispersive X-ray spectroscopy (EDS) equipped with energy dispersive X-ray and X-ray diffraction (XRD) analyses. In addition, the mechanical properties of these samples were evaluated using adhesion tests. The results show that the YSZ/NiCoCrAlYTa coating applied with the HVOF technique forms a more thin and continuous layer of TGO than that obtained when applying a YSZ/NiCoCrAlYTa coating using the APS technique, indicating that a severe brittle oxidation interface exists between the two layers. The results also indicate that the mechanical strength obtained from the adhesion test of the coated samples is observably affected by the oxidation behaviors obtained with the different deposition techniques chosen.     

Comparison of thermal shock resistances of plasma-sprayed nanostructured and conventional yttria stabilized zirconia thermal barrier coatings

The main goal of the current study is evaluation and comparison of thermal shock behavior of plasma-sprayed nanostructured and conventional yttria stabilized zirconia (YSZ) thermal barrier coatings (TBCs). To this end, the nanostructured and conventional YSZ coatings were deposited by atmospheric plasma spraying (APS) on NiCoCrAlY-coated Inconel 738LC substrates. The thermal shock test was administered by quenching the samples in cold water of temperature 20–25 °C from 950 °C. In order to characterize elastic modulus of plasma-sprayed coatings, the Knoop indentation method was employed. Microstructural evaluation, elemental analysis, and phase analysis were performed using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffractometry (XRD) respectively. The results revealed that failures of both nanostructured and conventional TBCs were due to the spallation of ceramic top coat. Thermal stresses caused by mismatch of thermal expansion coefficients between the ceramic top coat and the underlying metallic components were recognized as the major factor of TBC failure. However, the nanostructured TBC, due to bimodal unique microstructure, presented an average thermal cycling lifetime that was approximately 1.5 times higher than that of the conventional TBC.     

Heat treatment effect on coating shock resistance of thermal barrier coating system with different types of bond coat

The effect of heat treatment, growth of the TGO layer, oxidation of bond coat, and the impact of the presence of two bond coats on the TBC's thermal shock resistance has been investigated experimentally. TGO oxide layers were created with two-time heat treatment of 12 and 24 h at 1000. Then the thermal shock test was performed on the APS/APS and HVOF/APS/APS samples. The results show that the use of two BCs and the presence of a thin TGO layer has a good effect on TBC performance. The presence of two BC layers increased the shock resistance by an average of 37.2%. 12 h heat treatment caused a 14.0% and 17.4% shock resistance increase in samples with the HVOF/APS/APS layer and APS/APS layer, respectively. 24 h heat treatment decreased the samples' performance by 6.7% and 10.2% for samples with two BC and one BC, respectively.     

Feasibility research of Yb3Al5O12 garnet as environmental barrier coating materials

In this work, Yb₃Al₅O₁₂ (YbAG) garnet, as a new material for environment barrier coating (EBC) application, was synthesized and prepared by atmospheric plasma spraying (APS). The phases and microstructures of the coatings were characterized by XRD, EDS and SEM, respectively. The thermal stability was measured by TG-DSC. The mechanical and thermal-physical properties, including Vickers hardness (H_v), fracture toughness (K_IC), Young's modulus (E), thermal conductivity (κ) and coefficient of thermal expansion (CTE) were also measured. The results showed that the as-sprayed coating was mainly composed of crystalline Yb₃Al₅O₁₂ and amorphous phase which crystallized at around 917 °C. Moreover, it has a hardness of 6.81 ± 0.23 GPa, fracture toughness of 1.61 ± 0.18 MPa m^1/2, as well as low thermal conductivity (0.82–1.37 W/m·K from RT-1000 °C) and an average coefficient of thermal expansion (CTE) (∼6.3 × 10⁻⁶ K⁻¹ from RT to 660 °C). In addition, the thermal shock and water-vapor corrosion behaviors of the Yb₃Al₅O₁₂-EBC systems on the SiC_f/SiC substrates were investigated and their failure mechanisms were analyzed in details. The Yb₃Al₅O₁₂ coating has an average thermal shock lifetime of 72 ± 10 cycles as well as an excellent resistance to steam. These combined properties indicated that the Yb₃Al₅O₁₂ coating might be a potential EBC material. Both the thermal shock failure and the steam recession of the Yb₃Al₅O₁₂-EBC systems are primarily associated with the CTE mismatch stress.     

Experimental investigation of Al2O3/8YSZ and CeO2/8YSZ plasma sprayed thermal barrier coating on diesel engine

In this research work, aluminium oxide/yttria stabilized zirconia (20%Al₂O₃/80%8YSZ) and ceria/yttria stabilized zirconia (20%CeO₂/80%8YSZ) were coated through atmospheric plasma spray technique (APS) as thermal barrier coating (TBC) over CoNiCrAlY bond coat on aluminium alloy (Al-13%Si) substrate piston crown material and their thermal cycling behavior were studied experimentally. Thermal cycle test of both samples were conducted at 800?°C. Microstructural, phase and elemental analysis of the TBC coatings were experimentally investigated. The performance, combustion and emission characteristics of Al₂O₃/8YSZ, CeO₂/8YSZ TBC coated and uncoated standard diesel engine were experimentally investigated. The test results revealed that CeO₂/8YSZ based TBC has an excellent thermal cycling behavior in comparison to the Al₂O₃/8YSZ based TBC. The spallation of the Al₂O₃/8YSZ TBC occurred mainly due to the formation of thermally grown oxide (TGO), and growth of residual stresses at top coating and bond coating interface. The experimental results also revealed that the increase of brake thermal efficiency and reduction of specific fuel consumption for both TBC coated engine. Further reduction of HC, CO and smoke and increase of NOx emission were recorded for both TBC coated engine compared to the standard diesel engine.     

Thermal shock resistance of thermal barrier coatings for nickel-based superalloy by supersonic plasma spraying

Double-layer thermal barrier coatings (TBCs), including a top ZrO₂ layer and an inner CoNiCrAlY layer, were deposited on nickel-based superalloy using supersonic atmospheric plasma spraying (SAPS). Thermal shock resistance of the TBCs between 1200 °C and room temperature was investigated. After thermal shock test, the adhesive strength of the coatings was evaluated through scratch test. The SAPS–TBCs present good thermal shock resistance, exhibiting only 0.26% mass gain up to 150-time thermal cycling. Before thermal cyclic treatment, SAPS–TBCs exhibited a strong adhesion with the absence of the thermally grown oxide (TGO) between out and inner layer. With the increasing of thermal cycles, the TGO layer was formed and its thickness firstly increased and then dropped down. The critical load fell down by about 32% for topcoat–bondcoat adhesion (up to 50 cycles) and 35% or so for TBCs–substrate adhesion (up to 150 cycles) compared to the counterpart of as-sprayed specimens. The strain introduced by the existence of TGO and mixed oxides resulted in a varied adhesion for TBCs on nickel-based alloy during thermal cycling.     

Effect of oxide growth on the stress development in double-ceramic-layer thermal barrier coatings

A numerical study is conducted to investigate the effect of oxide growth on the stress development within the plasma sprayed double-ceramic-layer thermal barrier coatings. The roles of oxide morphology, growth rate, and oxidation duration are discussed. A two-dimensional periodical unit-cell model is developed, taking into account the different interfacial roughnesses among the coatings layers. Thermal gradient conditions are imposed during the high-temperature period to represent the non-uniform temperature distributions throughout the coatings thickness. It is found that stresses in the regions that close to the interface of the ceramic layers result from the thermal expansion mismatch and the non-uniform temperature field, in which the oxide growth reveals negligible influence on the development of the stresses. The gradually thickening thermally grown oxide (TGO) mainly contributes to the variations of stress and inelastic strain evolutions in its nearby regions. The residual stress fields in the coatings are almost unaffected by the oxide thickness after operating for a sufficiently long time. During long-term operation, the large inelastic deformation is found to be the intrinsic reason responsible for the cracking in the vicinity of TGO.     

Characteristics and thermal cycling behavior of plasma-sprayed Ba(Mg1/3Ta2/3)O3 thermal barrier coatings

Ba(Mg_1/3Ta_2/3)O₃ (BMT) powders were synthesized by the solid state reaction method. BMT thermal barrier coatings (TBCs) were deposited by atmospheric plasma spraying (APS). The phase composition and microstructure of the BMT coatings were characterized. The thermal cycling behavior of the BMT coatings was investigated by the water quenching method from 1150 °C to room temperature. The results reveal that BMT powders have an ordered hexagonal perovskite structure, whereas the as-sprayed coating of BMT has a disordered cubic perovskite structure because of the different degree of structural order for different treatment conditions. During thermal cycling testing, the entire spalling of coatings occurred within the BMT coating near the bond coat. This is attributed to the following reasons: (1) the growth of a thermally grown oxides (TGO) layer, which leads to additional stresses in the coatings; (2) the coefficient of thermal expansion mismatch between the BMT coating and bond coat, which develops enormous stress in the coatings; (3) the precipitation of Ba₃Ta₅O₁₅ due to the evaporation of MgO during the spraying process, which changes the continuity of the coatings.     

Structure-property relationship and design of plasma-sprayed La2Ce2O7/8YSZ composite coatings for gas turbine blades

Novel lanthanum-cerium oxide/8?wt% yttria partially stabilized zirconia (LC/8YSZ) thermal barrier coatings (TBCs) were deposited by supersonic atmospheric plasma spraying. The thermal insulation temperature and thermal shock resistance of LC/8YSZ double-ceramic-layer TBCs (DCL-TBCs) were quantitatively evaluated by a burner rig test. The results showed that the thermal insulation temperature increased with the increase of LC layer thickness in DCL-TBCs. When the thickness ratio between LC layer and 8YSZ layer was close to 1:1, the DCL-TBCs had the highest thermal shock resistance. LC/8YSZ thickness ratio significantly affected the energy release rate and the stress induced by thermal gradient or sintering. The sintering stress was found to be the main reason that caused the delamination of LC layer, however, the stress induced by thermal gradient resulted in the spallation of YSZ layer.     

Comparison of microstructure and mechanical properties of plasma-sprayed nanostructured and conventional yttria stabilized zirconia thermal barrier coatings

The main goal of this paper was to evaluate and compare the microstructure and mechanical properties of plasma-sprayed nanostructured and conventional yttria stabilized zirconia (YSZ) thermal barrier coatings (TBCs). To this end, NiCrAlY bond coat, nanostructured, and conventional YSZ coatings were deposited on Inconel 738LC substrate by atmospheric plasma spraying (APS). The mechanical properties of the coating were evaluated using nanoindentation and bonding strength tests. The microstructure and phase composition of the coating were characterized by field emission scanning electron microscopy (FESEM) and X-ray diffractometry (XRD). The nanostructured YSZ coating contained both nanosized particles retained from the powder and microcolumnar grains formed through the resolidification of the molten part of the powder, whereas the microstructure of the conventional YSZ coating consisted of columnar grain splats only. The phase composition of the as-sprayed nanostructured coating consisted of the non-transformable tetragonal phase, while the conventional coating showed the presence of both the monoclinic and non-transformable tetragonal phases. The results of nanoindentation and bonding strength tests indicated that the mechanical properties of the nanostructured coating were better than those of the conventional coating.