Electrodeposition of zinc on AZ91D magnesium alloy pre‐treated by stannate conversion coatings

A stannate chemical conversion process followed by an activation procedure was employed as the pre‐treatment process for AZ91D magnesium alloy substrate. Zn was electroplated onto the pre‐treated AZ91D magnesium alloy surface from pyrophosphate bath to improve the corrosion resistance and the solderability. The surface morphologies of conversion coating and zinc coating were examined with scanning electron microscope (SEM). The phase composition of conversion coating was investigated by X‐ray diffraction (XRD). The electrochemical corrosion behavior of the coatings in the corrosive solution was investigated by potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS). The experimental results showed that the activated stannate chemical conversion coating provided a suitable interface between zinc coating and the AZ91D magnesium alloy substrate. The corrosion resistance of the AZ91D substrate was improved by the zinc coating.     

AZ91 镁合金表面Ce-Mn 转化膜组织及性能表征

室温下,在AZ91 镁合金表面制备Ce-Mn 复合转化膜,通过单因素实验研究了Ce(NO3 )3 浓度和KMnO4 浓度对转化膜耐腐蚀性能的影响,确定了较佳的浓度配比。分析了转化膜的结构及组成,通过交流阻抗谱,研究了Ce-Mn 对基体镁合金的防护机制。结果表明:Ce-Mn 转化膜为非晶态物相结构,膜层主要由铈、锰和少量镁的氧化物或氢氧化物组成,Ce-Mn 转化膜可对镁合金起到较好的防护作用。     

镁锂合金表面锌锰磷化膜的制备与性能表征

采用化学转化法在镁锂合金表面制备了外观深灰色、结构均匀致密、耐蚀性能良好的锌锰磷酸盐转化膜,并研究了磷化温度对磷化膜性能的影响。采用扫描电子显微镜(SEM)、能谱(EDS)仪、X射线光电子能谱(XPS)和X射线衍射(XRD)仪对膜层的表面形貌、化学组成及结构进行了表征。采用动电位极化曲线、电化学交流阻抗(EIS)和腐蚀失重实验对磷化膜的耐蚀性进行了研究。结果表明,锌锰磷化膜主要由Zn、Zn3(PO4)2、MnHPO4、Mn3(PO4)2组成。锌锰磷酸化膜起到了保护镁锂合金的作用,提高了镁锂合金的耐蚀性,当磷化温度为45℃时,磷化膜的腐蚀电流密度最低,腐蚀速率最小,耐蚀性能最好。     

一步电沉积Ca-P/CTS复合涂层的制备及其耐蚀性

通过一步电沉积法在AZ31镁合金基体表面上沉积钙磷/壳聚糖(Ca-P/CTS)复合涂层,通过共聚焦显微镜(CLSM)、扫描电镜(SEM)和红外光谱分析仪(FT-IR)对Ca-P/CTS复合涂层的形貌、结构以及成分进行分析,采用电化学测试研究了其耐蚀性。结果表明:Ca-P/CTS复合涂层能够有效提高AZ31镁合金基体的耐蚀性,当壳聚糖的质量浓度为0.2g/L时,复合涂层的耐蚀性最好。     

Application of CeH–V/ sol–gel composite coating for corrosion protection of AM60B magnesium alloy

Application of a composite coating on AM60B magnesium alloy consisting of cerium–vanadium conversion coating and a hybrid sol–gel layer was investigated. Scanning electron microscopy and energy dispersive X-ray spectroscopy analyses revealed a cracked nodular structure for the cerium–vanadium conversion coating which was mainly composed of O, Ce, V, and Mg atoms. All the cracks in the conversion coating were completely sealed by a thin, compact and defect-free hybrid sol–gel film. Potentiodynamic polarization and electrochemical impedance spectroscopy experiments in Harrison's solution showed that the cerium–vanadium conversion coating provides minimal protection against corrosion while the composite coating significantly increases the corrosion resistance of the magnesium alloy. Sol–gel film provides protection against corrosion by sealing cracks in the cerium–vanadium conversion coating and acting as a barrier. Scanning electron microscopy analyses after polarization tests confirmed the results obtained by the electrochemical tests.     

Influence of substrate composition on the formation of phytic acid conversion coatings

In this paper, the formation and corrosion resistance of the phytic acid conversion coatings on Mg, Al, and AZ91D magnesium alloy were contrastively investigated using scanning electronic microscopy (SEM), Auger electron spectroscopy (AES), Fourier transform infrared spectroscopy (FTIR), electronic probe microscopic analyzer (EPMA), electronic balance, and electrochemical methods. The influence of phytic acid conversion coating as a middle layer on the properties of the paint on magnesium alloys was also investigated. The results show that the formation process of the conversion coatings is evidently influenced by the compositions of the substrate. The coating on pure aluminum is thinner and compacter than that on pure magnesium and the coating formed on α phase in AZ91D magnesium alloy is thinner but denser than that on β phase. The phytic acid conversion coatings formed on Mg, Al, and AZ91D magnesium alloy can all increase their corrosion resistance. The active functional groups of hydroxyl and phosphate radical are rich in the conversion coatings, which can improve the bonding between the organic paint and magnesium alloy and then improve their corrosion resistance.     

镁合金磷酸盐 /氮化硅双层复合膜结构及耐蚀性能研究

目的针对传统镁合金化学转化膜裂纹尺寸大、耐腐蚀性差等问题,制备一种镁合金磷酸盐/氮化硅双层结构的抗腐蚀复合膜。方法先对镁合金进行传统磷酸盐转化处理,再运用等离子体增强化学气相沉积技术沉积氮化硅膜层,分析复合膜的形貌、元素分布、表面电位及极化曲线,并与磷酸盐转化膜进行对比。结果氮化硅膜层能在磷酸盐转化膜裂纹处选择性优先沉积,从而在相当程度上填补转化膜层的裂纹,形成致密的复合膜结构。具有复合膜结构的镁合金表面电位和腐蚀电位明显高于传统磷酸盐转化处理的镁合金。结论镁合金表面制备磷酸盐/氮化硅双层复合膜后,抗腐蚀能力明显高于传统磷酸盐转化处理的镁合金。     

Study of Cerium and Lanthanum Conversion Coatings on AZ63 Magnesium Alloy Surface

采用扫描电子显微镜,X射线能谱,Tafel极化曲线和电化学阻抗谱法研究了铈镧转化膜对AZ63镁合金耐蚀性能的影响。结果表明,铈和镧的复合转化膜比单一稀土膜的表面更加均匀致密,对镁合金的耐蚀性有明显改善。双稀土转化膜的缓蚀效果随着浸泡成膜时间的增长而增加。延长时效时间有助于铈和镧的进一步氧化,耐蚀性能先增后减,时效48 h膜层的耐蚀效果最好。     

镁合金直接化学镀Ni-B镀层的腐蚀电化学行为研究

  研究了镁合金表面化学镀Ni-B合金的电化学行为,采用电化学动电位扫描极化曲线和交流阻抗研究了Ni-B镀层的腐蚀电化学行为,结果表明,Ni-B镀层在3.5%NaCl溶液中具有优良的耐蚀性能.所得Ni-B镀层的自腐蚀电位在－400 mV左右,相对于基体-1460 mV提高了1000 mV,自腐蚀电流密度小于0.7 μA/cm²,相对于基体28.5 μA/cm²降低了近两个数量级,说明Ni-B镀层能够有效地提高AZ91D 镁合金的耐腐蚀性能,使AZ91D镁合金在35%NaCl溶液腐蚀介质中的腐蚀速度明显降低.电化学交流阻抗测试结果符合极化曲线的测量结果,化学镀Ni B镀层后的AZ91D镁合金在3.5％NaCl溶液中的阻抗值相对于基体提高两个数量级,表现为自腐蚀电流降低,阻抗值相应提高.     

20% Al2O3-SiO2(sf)/AZ91D镁基复合材料微弧氧化陶瓷层电化学腐蚀性能

在磷酸盐体系电解液中,对20%(体积分数)硅酸铝短纤维(Al2O3-SiO2)增强AZ91D镁基复合材料进行微弧氧化表面处理获得陶瓷层。利用扫描电子显微镜(SEM)和X射线衍射(XRD)仪分析陶瓷层的表面形貌、截面组织和相组成,采用动电位极化和电化学阻抗谱(EIS)测试评价微弧氧化陶瓷层的电化学腐蚀性能。结果表明,该陶瓷层主要由MgO和MgAl2O4相组成。陶瓷层的腐蚀电流密度比镁基复合材料基体低3个数量级,电化学阻抗大幅升高,耐腐蚀性能明显高于复合材料基体     

Characterization of anodic coating formed on Mg-3Nd-0.2Zn-0.4Zr Mg alloy in alkaline electrolyte

Anodization of rare earth-containing Mg alloy of Mg-3Nd-0.2Zn-0.4Zr(mass fraction,%)(NZ30K) was performed in composite electrolyte containing NaOH,KOH,K_2SiO_3,Na_2SiO_3,NaF,KF etc.The anodic coating was characterized by using X-ray diffraction(XRD),field emission electron scanning mieroscope(FE-SEM) and electron probe microscopic analysis(EPMA).The corrosion resistance of the anodized alloy and the substrate was evaluated in 5%NaCl solution using electrochemical impedance spectroscopy(EIS).The results o...     

载波钝化对AZ91D镁合金锡酸盐化学转化膜耐蚀性能的影响

用载波钝化方法控制AZ91D镁合金锡酸盐转化膜成膜过程,用扫描电镜（SEM）观察该转化膜的表面形貌,用极化曲线和电化学阻抗谱研究载波钝化对该转化膜耐蚀性能的影响。结果表明, 载波钝化使AZ91D镁合金表面生成一层颗粒直径略大于传统浸泡处理的锡酸盐转化膜,其耐蚀性能显著提高。     

PREPARATION OF MICROARC OXIDATION COATING ON (Al2O3-SiO2)sf/AZ91D MAGNESIUM MATRIX COMPOSITE AND ITS ELECTROCHEMICAL IMPEDANCE SPECTROSCOPIC ANALYSIS\par

在硅酸盐电解液体系中, 采用交流微弧氧化方法在增强体体积分数为33%的 (Al₂O₃-SiO₂)_sf/AZ91D镁基复合材料表面制备出完整的保护性氧化膜. 利用SEM, EDS和XRD分析了氧化膜的形貌、成分和相组成, 测量了膜层的显微硬度分布. 采用电化学阻抗谱(EIS)评价了微弧氧化表面处理前后复合材料的电化学腐蚀性能, 确立了不同浸泡时间对应的等效电路. 结果表明, 微弧氧化膜主要由MgO和Mg₂SiO₄相组成, 最大硬度达到1017 HV. 氧化膜电化学阻抗模值|Z|与镁合金基体相比大幅度提高, 耐腐蚀性能明显高于基体. 在3.5%NaCl溶液里浸泡96 h后, EIS出现感抗弧, 显示膜内部开始出现点蚀破坏. 氧化膜耐蚀性由膜内致密层特性所决定.     

Corrosion resistance and molecular dynamics behavior of the MAO/SAM composite coatings on magnesium alloy

To improve corrosion resistance of magnesium alloy AZ91D, y-Mercaptopropyltrimethoxysilane (MPTS) was assembled on the surface of micro-arc oxidation (MAO) treated magnesium alloy by self-assembly membrane (SAM) technique. The surface morphology and chemical components of the MAO/SAM composite coatings were analyzed by scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS). The corrosion resistance of samples was investigated by potentiodynamic polarization, electrochemical impedance spectroscopy and total immersion tests in a 3.5 wt % NaCl solution. The measured EIS data were simulated by an equivalent circuit. Also the molecular dynamic simulation was used to study the adsorption behavior at the molecular level. The results showed that the surface of magnesium alloy was well covered by the MAO/SAM composite coatings with a better corrosion resistance. Chemical adsorption was formed between the organic molecules and the surface of the MAO coating. The approach presented here afforded an effective alternative for surface modification of magnesium-based materials to meet the many aspects of the application requirements.     

Corrosion electrochemical behaviors of silane coating coated magnesium alloy in NaCl solution containing cerium nitrate

Sol–gel coatings cannot provide adequate corrosion protection for metal/alloys in the corrosive environments due to their high crack‐forming potential. This paper demonstrates the possibility to employ cerium nitrate as inhibitor to decrease the corrosion development of sol–gel‐based silane coating on the magnesium alloy in NaCl solution. Cerium nitrate was added into the NaCl solution where the silane coating coated magnesium alloy was immersed. Scanning electron microcopy (SEM) was used to examine surface morphology of the silane coating coated magnesium alloy immersed in NaCl solutions doped and undoped with cerium nitrate. The corrosion electrochemical behaviors were investigated using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) tests. The results showed that the introduction of cerium nitrate into NaCl solution could effectively inhibit the corrosion of the silane coating coated magnesium alloy. Moreover, the influence of concentration of cerium nitrate on the corrosion inhibition and the possible inhibiting mechanism were also discussed in detail.     

聚苯胺/环氧涂层对AZ91D镁合金耐蚀性能的影响

通过化学氧化法合成本征态及氢氟酸掺杂态聚苯胺(PANI),用红外光谱对其结构进行表征。以环氧树脂为成膜物质,在AZ91D镁合金基体上制备了本征态及氢氟酸掺杂的 PANI/环氧涂层,用EIS方法研究涂层在3.5%NaCl溶液中的耐蚀性,并用SEM对浸泡后基体表面形貌进行观察。实验结果表明,与环氧清漆相比,本征态PANI的加入明显改善了环氧涂层的耐蚀性,而氢氟酸掺杂后进一步提高了PANI/环氧涂层的性能。用XPS对基体表面分析,发现添加聚苯胺的涂层在镁合金表面形成了具有保护作用的产物膜。     

Environmentally friendly anodization on AZ31 magnesium alloy

A novel anodization which is environmentally friendly,low voltage and low energy consumption was developed to improve corrosion resistance of AZ31 magnesium alloy.The corrosion resistance of the anodic films was studied by electrochemical impcdance spectroscopy(EIS) and potentiodynamic polarization techniques.The microstructure and compositions of films were examined by SEM,XPS and XRD.A new kind of organic additive used in the electrolyte is friendly to the environment.The compact, intact and uniform co...     

镁锂合金表面高锰酸盐转化膜的研究

采用化学转化法在镁锂合金表面制得了结构致密、耐蚀性能较好的高锰酸盐转化膜,研究了转化液中高锰酸盐溶液浓度对成膜效果的影响.实验采用扫描电子显微镜(SEM)、X射线衍射仪(XRD)和X射线光电子能谱(XPS)对所制得转化膜的表面形貌、结构和组成进行了测试.同时,使用动电位极化曲线、电化学交流阻抗谱和腐蚀失重3种方法对镁锂合金及其转化膜的耐腐蚀性能进行了深入研究.结果表明:高锰酸盐转化膜较均匀、平整,间隙较小,转化膜主要由锰的氧化物组成.提高了镁锂合金的耐腐蚀性能,当高锰酸盐溶液浓度为4.0 g/L时,转化膜的腐蚀电流密度小、容抗弧大、腐蚀速率低,耐腐蚀性能佳.     

冷喷涂铬锆铜涂层在海水中的耐蚀性能

采用冷喷涂技术在普通碳钢基体上制备了厚度为300μm的铬锆铜涂层,用扫描电子显微镜(SEM)观察涂层的组织形貌。用开路电位（OCP）、电化学阻抗谱和动电位极化曲线等电化学方法研究冷喷涂铬锆铜涂层在天然海水中的耐蚀性能。研究表明,铬锆铜涂层组织致密,在海水环境中,涂层表面形成一层致密的腐蚀产物膜,能有效阻止腐蚀介质向涂层内部渗透,对基体起到良好的保护作用。     

AZ31B镁合金氧化石墨烯掺杂钇盐转化膜耐蚀性研究

目的研究一种绿色环保的表面处理方法,以提高镁合金的耐蚀性。方法采用化学浸泡法,以硝酸钇为成膜物质,在AZ31B镁合金表面成功制备一种新型稀土盐转化膜,并以氧化石墨烯为阻隔剂对该转化膜进行复合掺杂。采用扫描电镜(SEM)对膜层的表面形貌进行观察,采用析氢实验和电化学测试对不同试样在3.5%Na Cl溶液中的耐蚀性进行了研究。结果镁合金钇盐转化膜表面平整均一,覆盖良好。氧化石墨烯掺杂后的钇盐膜层表面出现了大小不均一的瘤状物质,膜层完整,未出现裂痕。析氢实验结果显示,经过处理的转化膜试样可以极大地抑制腐蚀反应的发生。由极化曲线可知,钇盐转化膜的存在使镁合金的腐蚀电位发生了明显正移,正移了150 m V;而氧化石墨烯掺杂的钇盐膜层的腐蚀电位相对于掺杂前变化不大,但其腐蚀电流密度是掺杂前的1/28。电化学交流阻抗谱的测试结果显示,氧化石墨烯掺杂钇盐转化膜的电荷转移电阻最大,Rct为2485?·cm2;钇盐转化膜的电荷转移电阻次之,Rct为1224?·cm2。两者的电荷转移电阻相对于未经处理的镁合金都有明显提升。结论钇盐转化膜可以明显提高AZ31B镁合金的耐蚀性,氧化石墨烯的加入可以进一步提高转化膜层的耐蚀性。