共查询到15条相似文献,搜索用时 62 毫秒
1.
2.
奥氏体耐热不锈钢309S高温抗氧化性能研究 总被引:1,自引:0,他引:1
采用不连续称重法测得了奥氏体耐热不锈钢309S在不同温度下的高温氧化动力学曲线,结果表明309S钢高温氧化动力学曲线遵循抛物线规律.利用扫描电镜、X射线衍射和XPS的方法对氧化膜表面的形貌及化学元素沿氧化膜纵深方向的分布情况进行了研究,发现各温度下的氧化膜均均匀覆盖于基体表面;500℃下氧化膜氧化产物表层主要为Cr2O3和Fe2O3,内层主要为Cr2O3和NiO;1 000℃下氧化膜表层主要成分为Cr2O3、NiO、Fe3O4或Fe2O3,氧化膜内层基本不含NiO,主要为Cr2O3、Fe3O4或Fe2O3. 相似文献
3.
4.
5.
6.
对比了冷轧和拨拔两种不同工艺下,铁铬铝合金丝在表面状态.高温氧化增重率,合金含量的变化、氧化膜及强其断口形貌等方面的差异,研究证明,冷轧合金丝比冷拔丝具有较优良的高温抗氧化性能。 相似文献
7.
研究了310S耐热不锈钢在800、900、1000、1100、1200℃时高温循环氧化性能,采用SEM、XRD、EDS对高温循环氧化生成物进行分析。实验结果表明:1000℃以下时,钢的氧化速率较为缓慢,当温度达到1200℃时其氧化速率急剧增加。310S耐热不锈钢高温循环氧化产物分为3层,外层是FeO·Cr2O3和尖晶石结构的MnCr2O4,中间为Cr2O3,内层为SiO2氧化膜,这种结构是其具有良好耐高温氧化性能的主要原因。 相似文献
8.
通过压力机和手动轧制机对WS-4非自耗真空电弧炉熔炼制备的Al的质量分数为0%、2%、4%的310S耐热钢在950~1 250℃进行开坯轧制,研究不同Al含量的310S耐热钢热轧板材在800℃下的高温拉伸性能,用SEM观察拉伸断口。结果表明:不含Al和Al的质量分数为2%的合金,它们的高温抗拉强度均为210 MPa左右,但当Al的质量分数增加到4%时,合金的热强性显著提高。3种合金拉伸断面均可以看到大小明显不同的显微韧窝,合金在断裂前经历了比较大的塑性变形,所以均为韧性沿晶断裂。随Al含量的增加,合金断口中的显微韧窝所占的比例随之增加。 相似文献
9.
为了进一步提高310S钢种的洁净度,满足其耐蚀性能。利用化学分析、金相及小样电解、扫描电镜等手段研究了以EAF+AOD+LF流程生产310S耐热钢原精炼工艺下的钢水洁净度,并在此基础上提出了优化方案。结果表明,通过适当提高AOD还原炉渣碱度、LF进站采用铝粉进行深脱氧和延长大流量底吹氩气搅拌时间等手段提高了310S钢水洁净度,其中连铸坯w(T[O])由0.003 4%下降到0.002 5%,消除了直径大于30μm的大颗粒夹杂物,直径超过15μm的夹杂物数量减少了5.8%,1~7μm的弥散夹杂物数量增加了15.5%。 相似文献
10.
采用SEM与XPS,对Mg-11Al-3Zn+xCa高温氧化膜的物相组成和化学成分进行定性和定量分析。结果表明:含Ca镁合金高温氧化时,表面形成了致密的CaO/MgO保护层,改善了Mg-11Al-3Zn疏松的蜂窝状氧化膜结构,消除了氧化膜开裂现象,显著地增强了镁合金高温抗氧化性能。 相似文献
11.
Oxidation rates and scale/steel interface configuration of 9Ni steels were investigated at 1000--1 250 ℃ in air. The results revealed that Cu addition caused high temperature oxidation resistance to deteriorate. High tempera ture oxidation rates increased and scale/steel interface configuration became complicated due to Cu addition. Scale/ steel interface appeared to be network above certain temperature. Temperature required to form network scale/steel interface dropped more than 100 ℃ for 1.5% Cu-containing steel. (Fe,Ni,Cu)x Oy in inner oxidation layer dissocia ted to Fe-Ni-Cu phase and released active oxygen which can react with base steel easily. So the inner oxidation layer became the second source of oxidizing agent besides atmosphere. Internal stress at austenite grain boundary caused local oxide to fragment. So the scale/steel interface appeared to be network. Liquid Si-rich phase formed at sufficient ly high temperature. Penetration of the liquid Si-rich phase along austenite grain enhanced austenite grain oxidizing. 相似文献
12.
《钢铁研究学报(英文版)》2016,(3):231-237
In order to figure out the oxidation behavior of steels during heating,five micro-alloyed steels were subjected to continuous and isothermal oxidation using the thermo gravimetric analyzer and the Gleeble-3500thermo-mechanical simulator.The microstructure of oxide scales,especially the thickness fractions of Fe2O3,Fe3O4 and FeO layers,was analyzed using the scanning electron microscope(SEM),electron probe microanalyzer(EPMA)and electron backscattered diffraction(EBSD)techniques.The micro-alloyed steels containing alloying elements(Si,Cr,Ni and Cu)show a higher oxidation resistance compared with the low carbon steel.It is found that alloying elements accumulated at scale/substrate interface during high temperature oxidation.Alloying elements function in two ways in the oxidation of steels:one is enhancing the scale/substrate interface and consequently suppressing the blister of scales;and the other is impeding the outward diffusion of iron cations from substrate to scales,resulting in the decrease of oxidation rate.As the diffusion of iron cations is impeded,the thickness fractions of Fe2O3 and Fe3O4of micro-alloyed steels are more than those of low carbon steels. 相似文献
13.
14.
对奥氏体耐热不锈刚310S在800、1 000、1 200℃下氧化140 h形成的氧化膜断面及基体进行能谱分析。结果发现:随着温度的升高,氧化膜厚度增加;氧化膜都由Mn、Cr和Si的氧化物组成,Mn、Cr的氧化物分布在氧化膜最外层,Si的氧化物分布在内层;同时,当温度升高到1 200℃时,基体发生了严重的Si内氧化,导致奥氏体耐热不锈刚310S抗氧化性降低。 相似文献
15.
Cu-Cr合金高温氧化行为分析 总被引:3,自引:0,他引:3
该文用热分析天平,结合金相、X射线衍射(XRD)、扫描电镜(SEM)和能谱(EXD)研究了Cu—Cr合金在不同温度下的氧化行为。结果表明,Cu—Cr合金在700℃-900℃氧化符合抛物线规律,其最外层氧化膜为CuO,内层为Cu2O和Cr2O3,铬有助于提高合金的抗氧化能力。 相似文献