激光冲击强化与喷丸提高不锈钢疲劳性能对比研究

对不锈钢材料1Cr11Ni2W2MoV进行了激光冲击强化和喷丸强化后表面粗糙度和残余应力测试分析,与喷丸相比,激光冲击强化对试件表面形貌和表面粗糙度的影响更小,产生的残余压应力更大。对光滑试件和2种强化后试件的振动疲劳对比试验表明,激光冲击强化能显著提高不锈钢材料振动疲劳寿命,是喷丸的2倍以上。     

Surface durability of powder-forged roller treated by shot peening

To investigate the influence of shot peening on the surface durability of powder-forged rollers, the case-hardened powder-forged rollers with a forging density of 7.5 g/cm³ treated by the single shot peening and the double shot peening were fatigue-tested under a sliding-rolling contact condition. The surface roughness, the surface hardness and the surface compressive residual stress of the rollers were increased by the shot peening. In addition, the pores near the roller surface were deformed by the shot peening. The failure mode of all the test rollers was spalling due to subsurface cracking. The fatigue lives of all the test rollers were improved by the shot peening, and that of the test roller S08, which was shot-peened with the hardest steel shots in this experimental range, was especially improved. The surface durability of the test roller S08 was also most improved by the shot peening. Cracks became difficult to occur and propagate under the roller surface since the pores near the roller surface were deformed by the stronger shot peening. In this study, double shot peening, which generally restrains the increase in surface roughness, was not particularly effective for the improvement in the surface durability of the powder-forged rollers, because the influence of tangential force on fatigue was not always great in a case of subsurface cracking.     

Effect of shot peening parameters on microhardness of AISI 1045 and 316L material: an analysis using design of experiment

Shot peening is widely used to improve the fatigue properties of components and structures. Residual stresses, surface roughness, and work hardening are the main beneficial effects induced in the surface layer from shot peening, which depend on the correct choice of the peening parameters. In this investigation, experiments were designed using the full factorial design of experiment (DOE) technique and an air blast type of shot peening machine. Effects of process parameters such as pressure, shot size, stand-off distance, and exposure time on surface microhardness for AISI 1045 and 316L materials were investigated. An ANOVA was carried out to identify the significant peening parameters. In the case of 316L material, the maximum surface hardness was found to be in the range of 450–824 Hv, whereas it was found to be in the range of 314–360 Hv for AISI 1045. A critical assessment was made so as to understand the variation of microhardness in the direction of peening. Empirical equations between the peening parameters and the surface microhardness for both materials were developed, which are useful in predicting the surface microhardness. It is believed that this technique could prove beneficial in industries for reduction of performance variation and cost and to increase productivity.     

Mechanical and Tribological Properties of Shot-Peened SAE 1070 Steel

The effects of shot peening pressure on the mechanical and tribological properties of shot-peened SAE 1070 steel strips were systematically investigated. The surface hardness of the shot-peened steel strips significantly increased with increased shot peening pressure due to the promoted cold work-hardening effect. The tribological results showed that the increased surface roughness of the shot-peened steel strips associated with increased shot peening pressure resulted in their increased friction by enhancing mechanical interlocking between two rubbing surfaces. The wear of the shot-peened steel strips decreased with increased shot peening pressure via their increased surface hardness. However, the shot-peened steel strips at shot peening pressures less than 345 kPa did not exhibit better wear resistance than the as-received steel strip, indicating that a certain intensity of shot peening was required to improve the wear resistance of the shot-peened steel strips. It could be concluded that the mechanical and tribological properties of the shot-peened steel strips were significantly influenced by the shot peening pressure.     

喷丸与激光喷丸强化高强度钢对比试验

为了考察和对比喷丸(SP)和激光喷丸(LSP)2种表面强化技术对金属零件的强化效果,以30CrMnSiNi2A钢为试样,进行喷丸和激光喷丸强化处理试验。试验结果显示,2种强化试样的残余压应力和硬度都有较大的提高。分别测定了喷丸强化和激光喷丸强化试样在同一应力水平下的疲劳寿命,并运用扫描电镜分析了两者的疲劳断口。试验结果表明,激光喷丸强化试样中值疲劳寿命是喷丸强化试样的1.11~2.75倍,激光喷丸强化比喷丸强化在提高金属零件表面性能方面的效果更佳。     

喷丸强化在新能源汽车轴齿上的应用

针对某新能源输入轴上仿真安全因子偏低的齿轮进行喷丸强化,结合其喷丸强化重点区域进行了有效的工装和喷丸饱和曲线工艺设计。同时,对喷丸后的齿面粗糙度以及规定位置进行了残余应力测试。喷丸后的输入轴应力合格及满足整车耐久测试要求,确认合理的喷丸能有效改善轴齿的应力状态,提高其弯曲和接触安全系数。     

Empirical modeling of shot peening parameters for welded austenitic stainless steel using grey relational analysis

The attempt of this paper is to present an effective approach for the optimization of the shot peening process of welded AISI 304 austenitic stainless steel with multi performance characteristics using Grey relational analysis (GRA) based on Taguchi orthogonal array. Twenty-seven experimental runs are performed to determine best process parameters level. An analysis of variance (ANOVA) is carried out to identify significant peening parameters. The response tables are obtained for analyzing the optimal levels of shot peening parameters and major factors that affect the quality function. The multiple performance characteristics including tensile strength, surface hardness and surface roughness are the quality functions considered for the optimization. Further mathematical models are developed using regression analysis for the tensile strength, surface hardness and surface roughness. It will be very helpful to the engineers in deciding the levels of the shot peening parameters for desired performance characteristics.     

Fretting Wear Behavior of Laser Peened Ti-6Al-4V

This work deals with the influence of laser peening on the fretting wear behavior of Ti-6Al-4V. Laser peening was carried out on Ti-6Al-4V. The laser-peened surface was characterized by transmission electron microscopy. Surface roughness, nanoindentation hardness, residual stress, and tensile properties of the material in both laser-peened and unpeened conditions were determined. Fretting wear tests were conducted at different normal loads using a ball-on-flat contact geometry. Laser peening resulted in the formation of nanocrystallites on the surface and near-surface regions, increased hardness, and compressive residual stress. Laser peening did not affect the tensile properties and surface roughness significantly. There was no considerable difference between the values of the tangential force coefficient of laser-peened and unpeened samples. The fretting scar size, wear volume, and wear rate of laser-peened specimens were lower than those of unpeened samples. This may be attributed to an increase in surface hardness due to strain hardening and grain refinement at the surface and near-surface regions, higher compressive residual stress, and higher resistance to plastic deformation of laser-peened samples.     

Relation between surface hardening and roughness induced by ultrasonic shot peening

This paper is focused on the identification of a relation between surface hardening and roughness induced by ultrasonic shot peening. A method that dissociates the influence of roughness from the value of the true macroscopic hardness is applied to AISI 316L stainless steel specimens treated using different processing conditions. The true macroscopic hardness is identified and used to determine the surface roughness parameter and scale that give the best relation between hardness and roughness. A relation is identified between the five point pit height S_5V roughness parameter (local depth of roughness) and hardness using a high-pass filter with a cut-off of 100 µm. This power function was identified at a scale that corresponds to the size of the shot impacts.     

Impact of surface hardening treatment generated by shot peening on the fatigue life of brass alloy

Brass alloy is widely used because of some attractive properties such as high electrical and thermal conductivity. But its fatigue performance after surface treatment is not very well explored in literature. Thus, in the present work, particular emphasis was given to the influence of surface treatment by shot peening on the fatigue life of brass alloy, throughout surface roughness and microstructural evolution. Fatigue tests were performed on unpeened, peened and peened then polished specimens. Various times of surface hardening treatment as 30, 60 and 120 min were considered. Experimental results reveal that the fatigue life of peened brass alloy decrease for all studied hardening treatment conditions. Surface roughness and microstructural properties showed large sensitivity to the shot peening process of brass alloy.     

Effect of shot peening on rolling contact fatigue and lubricant film thickness within mixed lubricated non-conformal rolling/sliding contacts

The effect of shot peening on rolling contact fatigue (RCF) and lubricant film thickness within non-conformal rolling/sliding contacts operated under mixed lubrication conditions was observed in this study. Rolling contact fatigue tests and film thickness measurements were carried out using specimens with modified surface topography by shot peening process using glass beads having diameter between 0.07 and 0.11 mm. It has been shown that the effect of shot peening on RCF has no positive effect even if shot peened surface of the roller exhibited somewhat higher hardness in contrast to the grounded surface. The reduction of RCF may be caused due to asperities interactions because after shot peening the surface roughness of the roller was increased. Film thickness measurements confirmed that the contact is realized actually only between asperity peaks of shot peened ball and smooth disc.Conversely, no negative effect on RCF was observed when the shot peened surface of the roller was polished. The polish of asperity peaks causes the creation of lands and micro-cavities, which may be employed as lubricant micro-reservoirs. From film thickness measurements it has been observed that lubricant emitted by shallow micro-cavities can provide the local increase in lubrication film thickness, which thereby reduces asperities interactions. Similar results were obtained for start-up conditions where the squeeze lubricant enlarges film thickness and reduces surface interactions.From the obtained results, it can be suggested that properly designed surface topography modification could help to increase the efficiency of lubrication films leading to the enhancement of contact fatigue life of non-conformal mixed lubricated rolling/sliding contacts.     

Abrasive wear behaviour of laser sintered iron–SiC composites

Direct metal laser sintering (DMLS) is one of the popular rapid prototyping technologies for producing metal prototypes and tooling of complex geometry in a short time. However, processing of metal matrix composites (MMCs) by laser sintering is still in infant stage. Thermal cracks and de-bonding of reinforcements are reported while processing MMCs by laser sintering process. There are reports on use of metallic-coated ceramic reinforcements to overcome these problems. The present investigation is aimed at using nickel-coated SiC in developing iron composites by DMLS technique and to characterize its abrasive wear behaviour.Microstructure, microhardness, and abrasive wear tests have been carried out on both DMLS iron and its composites sintered at a laser scan speed of 100 mm/s. Abrasion wear tests have been carried out using a pin-on-disc type machine. SiC abrasive papers of grit size 60, 80, and 150 having an average particle size of 268, 192, and 93 μm, respectively, have been used. Load was varied between 5 and 25 N in steps of 5, while the sliding distance and sliding velocity of 540 m and 2.5 m/s, respectively was adopted for all the tests. Optical, scanning electron micrograph and surface roughness observation of worn surfaces have been undertaken.An increase in microhardness and a decrease in density of the laser sintered iron–SiC composites was observed with increase in SiC content. The abrasive wear resistance of composites increases with increased content of SiC in iron matrix. For a given grit size of SiC abrasive paper, at all the loads studied, iron–SiC composites exhibit excellent abrasive wear resistance. Increase in abrasive wear was observed with the increase in abrasive particle size.     

16MnR焊接接头高能喷丸表面强化的研究

采用16MnR压力容器钢气体保护焊接头进行高能喷丸表面强化试验,利用金相显微镜、扫描电镜、硬度测试以及X射线衍射等方法对不同时间喷丸处理的表层组织形貌、变形层硬度以及晶粒尺寸进行了分析。结果表明,焊接接头的焊缝、热影响区和母材随着喷丸时间的延长,晶粒逐渐细化,表层硬度和硬化层深度逐渐增加,显微硬度随着距表层深度的增加而降低,当喷丸时间120min时,焊缝、热影响区、母材表层硬度可分别提高240HV、215HV、223HV。喷丸时间继续增加,硬度值增幅不明显。综合喷丸时间对表层组织、硬度和变形层深度的影响,焊接接头各区结果都显示120min喷丸处理的样品强化效果最佳。     

喷丸强化因素对钛合金固体粒子冲蚀抗力的影响

探讨了喷丸强化(SP)因素(残余压应力引入、表面粗糙度增大和表面加工硬化等)对Ti6Al4V钛合金固体粒子冲蚀(SPE)行为的影响和作用机制,为充分发挥SP改进航空发动机零部件服役性能的潜力提供依据。结果表明:Ti6Al4V合金表面直接喷丸处理,其SPE抗力无明显改变;SP处理后进行表面抛光,Ti6Al4V合金SPE抗力明显增加。SP造成的表面粗糙度增大导致了钛合金在大小冲击攻角下的SPE抗力的下降;SP引入的表面残余压应力对提高钛合金在90°大攻角下的SPE抗力起了重要作用,原因是SP残余压应力增加了裂纹闭合力和抑制了疲劳裂纹早期扩展;SP引起的表面加工硬化作用对提高钛合金在30°小攻角下的SPE抗力有重要贡献,这归于加工硬化提高了材料表面在小攻角下的微犁削抗力。     

A non-local fatigue approach to quantify Ti-10V-2Fe-3Al fretting cracking process: Application to grinding and shot peening

This paper presents an experimental study on the tribological behaviour and cracking response of a Ti-10V-2Fe-3Al titanium alloy under fretting loading with a cylinder on plane configuration. Three types of surfaces were investigated: a polished one considered as the reference, a ground one and a shot peened surface. Surfaces were compared with respect to residual stress, hardness and roughness. The first step of this study was to determine sliding conditions and coefficient of friction of the three contact types. Next, fretting tests under stabilized partial slip regime were carried out to investigate crack nucleation and propagation. Results show that whatever surface roughness or residual stress in the material, tribological behaviour is the same. These latter confirm that sliding condition and coefficient of friction in partial slip regime is due to material effect and not to roughness or surface hardness. Then, residual stress induced by grinding or shot peening have no influence on the crack nucleation threshold under fretting solicitation because crack nucleation is only induced by a sufficient tangential loading. The crack nucleation threshold is formalized by applying the Crossland criterion taking into account the stress gradient and the ensuing “size effect”. As expected, cracks propagation is influenced by residual stress under the surface. Compared to the reference case, for a same loading parameters set, residual stress induced by grinding is not sufficient to decrease the crack length reached whereas effects of shot peening decrease highly these latter. So, there is a threshold of residual stress from which residual stresses are useful against cracking.     

FEM of residual stress and surface displacement of a single shot in high repetition laser shock peening on biodegradable magnesium implant

Laser shock peening (LSP) is one of the prominent surface processing techniques to improve the mechanical characteristics by inducing compressive residual stress on the specimen surface. Generally, LSP is performed using high energy, low repetition pulsed laser. Recently, High repetition laser shock peening (HRLSP) on biodegradable magnesium alloys has been reported. Increased speed and reduced operating costs are the key highlights of HRLSP. This work is aimed towards understanding of the residual stress profile beneath the specimen surface, where a Finite element method (FEM) has been proposed to show the ability of a tightly focussed nanosecond laser pulse for peening magnesium. The depth of maximum compressive residual stress of 48 MPa at 28 mm beneath surface was the result of the simulation. Also the Von Misses stress was analytically found to be 31.5 MPa, which is similar to the value from FEM at 30 MPa. Furthermore, the plastic displacement of FEM at 4.02 µm compares reasonably well with the experimental result at 3.698 µm, thereby validating the Finite element model. If increase in CRS can be created by single shot of laser pulse, it can be concluded that the same can be done beneath the entire magnesium surface using appropriate scanning protocols.

     

喷丸残余应力场有限元模拟研究进展

喷丸强化处理工艺可以显著提高金属材料的抗疲劳和抗应力腐蚀等性能,这与喷丸后在金属表面层形成的残余应力场紧密相关,因此对喷丸残余应力的大小及分布进行预测具有重要意义.对近年国内外喷丸残余应力场的有限元模拟进行评述,总结出6种典型的残余应力分析模型,分别是二维轴对称模型、四对称面模型、三对称面模型、双对称面模型、单对称面模...     

曲面铝合金锤击平整技术研究

以曲面铝合金为例,利用工业机器人锤击的方式对曲面类零件表面进行平整,并探究各锤击工艺参数对其表面的粗糙度、硬度及表面形貌的影响.将锤击装置装夹到工业机器人上,控制工业机器人以矩形光栅式运动路径对曲面铝合金表面进行锤击加工,并对锤击后表面的粗糙度、硬度及表面形貌进行测量观察.结果表明:经锤击加工后的铝合金表面粗糙度可达0...     

Some investigations into development of nozzle and suction system for air blast shot peening machine

Shot peening is an important surface enhancement process, which helps in assuring satisfactory fatigue life and reliability of the automotive, aerospace and marine components. One of the most important factors affecting shot peening performance is the type of shot peening machine. This paper presents an innovative design of a laboratory-based air blast shot peening machine. This machine has a vertical nozzle suction system to take the advantage of gravity feed as well as the feed created by suction of the pressurized air. Special attention was paid to the design of the nozzle and the mixing chamber so as to obtain adequate suction of shots. The performance of the machine was evaluated by carrying out various shot peening tests on AISI 1045 steel specimens. The tests included microscopic examination of coverage with ×10 magnification lens, fatigue and wear resistance. The wear resistance of the peened AISI 1045 material increased by 3.5 times the unpeened one. The fatigue tests showed improvement in fatigue life of the workpiece up to about four times. Besides, there was an increase in yield and torsional strength of the workpiece by about 1.5 times.     

激光喷丸强化系统协调控制方法与实现

针对复杂型面工件激光喷丸强化应用中对加工点位精度的要求以及激光脉冲触发时间点需要与工业机器人调姿到位时间点精确匹配,提出激光脉冲与工业机器人协调控制方法。通过脉冲能量检测实现出光快速反馈,并基于EKI接口通讯实现KUKA机器人运动控制及到位反馈,完成激光脉冲与工业机器人点位运动闭环匹配。在此基础上研制激光喷丸强化工艺系统,主要包含激光光源、工业机器人、传输光路、工艺辅助模块以及上位机控制平台。以平面点阵坐标进行协调控制实验及对整体叶盘进行激光喷丸强化实验。结果表明,本系统具备较好的激光脉冲-工业机器人协调控制精度,能自动完成激光喷丸强化工艺流程,具有对复杂型面工件的激光喷丸强化能力。