Influence of Tetraalkylammonium Compounds on Photocatalytic and Physical Properties of TiO<Subscript>2</Subscript>

A wide range of experimental data are reported for the first time on the TiO₂ prepared by hydrolysis of highly concentrated Ti(OⁱPr)₄ in water solutions of quaternary ammonium compounds (QACs). These TiO₂ materials have been shown to be photocatalytically active under visible light irradiation (LED, 450 nm) using acetone as a model substrate oxidized in the gas phase. Five-fold increase in activity in comparison with the commercial photocatalyst KRONOClean 7000 is achieved. Colloidal solutions of hydrolyzed Ti(OⁱPr)₄ have been studied by SAXS method suggesting the way in which QACs solutions may influence the final composition of TiO₂. Phase composition, morphology, texture and surface properties of the modified TiO₂ have been studied using XRD, BET, SEM and low-temperature FTIR with CO probe. The surface elemental composition has been investigated by XPS method. Additional low-energy levels and high concentration of acid surface sites originated from N/C-doping, are likely to be the main reasons for exceptional photocatalytic performance of these samples.

Graphical Abstract

Open image in new window

     

Photocatalytic inactivation and removal of algae with TiO<Subscript>2</Subscript>-coated materials

The capabilities of TiO₂-coated materials for the inactivation and removal of algae were investigated. As supports for TiO₂, non-woven fabric and Ni foam were chosen. To evaluate the ability of noble metal cocatalyst additions to facilitate the photocatalytic algal inhibition of TiO₂-coated materials, Pd nanoparticles were deposited on non-woven fabric-supported TiO₂ by photoelectrochemical deposition. The fabric-supported Pd/TiO₂ showed higher inhibition activity for algal growth compared to the fabric-supported TiO₂ without Pd. In addition, Ni foam-supported TiO₂ also showed high inhibition activity, both in laboratory-scale tests and open-air tests. Therefore, TiO₂-coated materials with suitable coating methods such as the use of cocatalysts or large surface area can substantially inhibit algal growth. The ability of the TiO₂-coated materials to inhibit algae correlated well with their activity for the photocatalytic decolorization of methylene blue, suggesting a nonspecific mechanism in the breakdown of cellular structures.     

Photocatalytic Generation of H<Subscript>2</Subscript> Gas from Neat Ethanol over Pt/TiO<Subscript>2</Subscript> Nanotube Catalysts

TiO₂ nanotubes promoted with Pt metal were prepared and tested to be the photocatalytic dehydrogenation catalyst in neat ethanol for producing H₂ gas (C₂H₅OHC₃CHO +H₂). It was found that the ability to produce H₂, the liquid phase product distribution and the catlyst stability of these promoted nano catalysts all depended on the Pt loading and catalyst preparation procedure. These Pt/TiO₂ catalysts with TiO₂ nanotubes washed with diluted H₂SO₄ solution produced 1, 2-diethoxy ethane (acetal) as the major liquid phase product, while over those washed with diluted HCl solution or H₂O, acetaldehyde was the major liquid phase product.     

Synergism Between Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Au/TiO<Subscript>2</Subscript> in the Low Temperature Oxidation of Propene

CO impedes the low temperature (<170 °C) oxidation of C₃H₆ on supported Pt. Supported Au catalysts are very effective in the removal of CO by oxidation, although it has little propene oxidation activity under these conditions. Addition of Au/TiO₂ to Pt/Al₂O₃ either as a physical mixture or as a pre-catalyst removes the CO and lowers the light-off temperature (T ₅₀) for C₃H₆ oxidation compared with Pt catalyst alone by ~54 °C in a feed of 1% CO, 400 ppm C₃H₆, 14% O₂, 2% H₂O.     

Adsorption of thallium cations on RuO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript> electrodes

The electrochemical ion-exchange properties of RuO₂–TiO₂ film electrodes with different composition have been studied in acidic and alkaline media. Thallium-cation uptake has been observed only from the latter and its extent was found to be a function of electrode potential and composition. At potentials near 0.0 V (RHE), the amount of adsorbed Tl⁺ exhibited a maximum, and decreased with increasing potential, reaching a broad minimum in the range 0.4–0.8 V. A further increase in the electrode potential, above about 1.0 V, led to an increase of adsorbed thallium species, essentially due to deposition of a few layers of Tl(III) hydroxide. In fact, the release of the latter species was found to be much slower than that of thallium ions adsorbed at 0.0 V. For the latter, in turn, the double injection/ejection mechanism, currently accepted to explain the charge-storage in oxide electrodes, seems to be confirmed. The high Γ values attained at 0.0 V indicate that the large ionic radius of Tl⁺ does not prevent its diffusion through the thinner pore texture of the oxide coatings, possibly because of its poor hydration, related with lower charge density at the ion surfaces.     

Dye sensitized CO<Subscript>2</Subscript> reduction over pure and platinized TiO<Subscript>2</Subscript>

TiO₂ thin and thick films promoted with platinum and organic sensitizers including novel perylene diimide dyes (PDI) were prepared and tested for carbon dioxide reduction with water under visible light. TiO₂ films were prepared by a dip coating sol–gel technique. Pt was incorporated on TiO₂ surface by wet impregnation [Pt(on).TiO₂], or in the TiO₂ film [Pt(in).TiO₂] by adding the precursor in the sol. When tris (2,2′-bipyridyl) ruthenium(II) chloride hexahydrate was used as sensitizer, in addition to visible light activity towards methane production, H₂ evolution was also observed. Perylene diimide derivatives used in this study have shown light harvesting capability similar to the tris (2,2′-bipyridyl) ruthenium(II) chloride hexahydrate.     

Effect of TiO<Subscript>2</Subscript> loading on the activity of V/TiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> in the catalytic oxidehydrogenation of ethylbenzene with carbon dioxide

TiO₂-Al₂O₃ mixed oxides with different compositions ranging from 40wt-% to 95wt-% of TiO₂ were prepared by sol-gel method and impregnated with different amounts of VO _x . Supports and catalysts were characterized by X-ray diffraction (XRD), physisorption, temperature preprogrammed reduction (H₂-TPR), and ammonia temperature programmed desorption (NH₃-TPD). TiO₂ content in the support had obvious effect on the crystal structure, texture characteristic, acid property, and catalytic activity in dehydrogenation of ethylbenzene (EB) with carbon dioxide. The highest catalytic activity was acquired when the TiO₂ content was 50 wt-%.     

Li<Subscript>2</Subscript>Cu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> + SiO<Subscript>2</Subscript>/Ti compositions for the catalytic afterburning of diesel soot

Two methods were used to obtain a catalytically active oxide coating on the surface of titanium for the catalytic afterburning of diesel soot: plasma electrochemical formation of an oxide film on the surface of titanium and extraction pyrolytic deposition of the Li₂Cu₂(MoO₄)₃ compound. The Li₂Cu₂(MoO₄)₃/TiO₂ + SiO₂/Ti compositions synthesized by the single-step extraction pyrolytic treatment of the oxidized surface of titanium ensured a high burning rate of soot of ∼300°C. The subsequent deposition of Li₂Cu₂(MoO₄)₃ lowers the activity of the catalyst, due probably to the growth of molybdate phase crystallites and the filling of open oxide film pores. Double lithium-copper molybdate is able to reduce appreciably the concentration of CO in the oxidation products of soot. The advantages of these methods are the possibility of forming high-cohesion durable coatings on surfaces of any complexity, the simplicity of their implementation, and high productivity and low cost. The obtained results can be recommended for use in developing methods for creating composite coatings on catalytic soot filters.     

Ni<Superscript>2+</Superscript> reduction under solar irradiation over CuFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/TiO<Subscript>2</Subscript> catalysts

The photo-electrochemical characterization of the hetero-system CoFe₂O₄/TiO₂ was undertaken for the Ni²⁺ reduction under solar light. The spinel CoFe₂O₄ was prepared by nitrate route at 940 °C and the optical gap (1.66 eV) was well matched to the sun spectrum. The flat band potential (-0.21 V_SCE) is more cathodic than the potential of Ni²⁺/Ni couple (-0.6 V_SCE), thus leading to a feasible nickel photoreduction. TiO₂ with a gap of 3.2 eV is used to mediate the electrons transfer. The reaction is achieved in batch configuration and is optimized with respect to Ni²⁺ concentration (30 ppm); a reduction percentage of 72% is obtained under sunlight, the Ni²⁺ reduction is strongly enhanced and follows a first order kinetic with a rate constant of 4.6×10^-2 min^-1 according to the Langmuir-Hinshelwood model.     

Preparation of TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> composite oxide and its photocatalytic degradation of rhodamine B

The composite semiconductor photocatalyst TiO₂/SiO₂ was prepared by template-hydrothermal method using carbon spheres as the template. The structural and optical properties of TiO₂/SiO₂ were characterized by XRD, SEM, BET, UV–Vis DRS, TG-DTA, PL techniques. The formation of hydroxyl radical on the surface of TiO₂/SiO₂ was studied with terephthalic acid as the probe molecule, combined with fluorescence technique. The results showed that the specific surface area of TiO₂/SiO₂ composite was 327.9 m²/g, and the specific surface area of TiO₂/SiO₂ was larger than that of pure TiO₂. Photocatalytic degradation of rhodamine B showed that TiO₂/SiO₂ composite oxide under visible light illumination 40 min, the degradation rate was 98.6 % and the degradation rate of pure TiO₂ was only 11.9 %. The apparent first-order rate constant of TiO₂/SiO₂ was 33 times that of pure TiO₂ and more than 6 times that of P25 when the molar ratio of Ti to Si was 1:1 under visible light irradiation. Moreover, it’s also as much as 5 times that of pure TiO₂ and is more than 1 times that of P25 under UV light irradiation 25 min. Based on the experimental results, ^·O₂ ^? and h⁺ were suggested to be the major active species which was responsible for the degradation reaction. The increased photocatalytic activity of TiO₂/SiO₂ may be mainly attributed to effectively suppressing the recombination of hole/electron pairs. After the photocatalyst TiO₂/SiO₂ was reused 5 times, the degradation rate of rhodamine B could reach 89.2 % under visible light irradiation. Moreover, The composite semiconductor photocatalyst TiO₂/SiO₂ was selective towards the degradation of rhodamine B.     

Preparation of hydrophobic SiO<Subscript>2</Subscript>@(TiO<Subscript>2</Subscript>/MoS<Subscript>2</Subscript>) composite film and its self-cleaning properties

TiO₂/MoS₂ composite was encapsulated by hydrophobic SiO₂ nanoparticles using a sol–gel hydrothermal method with methyltriethoxysilane (MTES), titanium tetrachloride (TiCl₄), and molybdenum disulfide (MoS₂) as raw materials. Then, a novel dual functional composite film with hydrophobicity and photocatalytic activity was fabricated on a glass substrates via the combination of polydimethylsiloxane adhesives and hydrophobic SiO₂@(TiO₂/MoS₂) composite particles. The influence of the mole ratios of MTES to TiO₂/MoS₂ (M:T) on the wettability and photocatalytic activity of the composite film was discussed. The surface morphology, chemical compositions, and hydrophobicity of the composite film on the glass substrate were investigated by scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and water contact angle (water CA) measurements. The results indicated that the composite film exhibited stable superhydrophobicity and excellent photocatalytic activity for degradation of methyl orange (MO) even after five continuous cycles of photocatalytic reaction when M/T was 7:1. The water CA and degradation efficiency for MO remained at 154° and 94%, respectively. Further, the composite film showed a good non-sticking characteristic with the water sliding angle (SA) at about 4°. The SiO₂@(TiO₂/MoS₂) composite consisting of hydrophobic SiO₂ nanoparticles and TiO₂/MoS₂ heterostructure could provide synergistic effects for maintaining long-term self-cleaning performance.     

Combustion of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Al thermit mixtures in steel tubes

Explored was the combustion of Fe₂O₃/TiO₂/Al thermit mixtures in steel tubes upon variation in green composition and with special emphasis on the dependence of combustion temperature T _c and burning velocity U on reaction heat Q. Special attention was given to incompleteness of combustion for compositions with low Q.     

Effect of Co,Ga, and Nd Additions on the Photocatalytic Properties of TiO<Subscript>2</Subscript> Nanopowders

In the present study, metal-ion-doped TiO₂ powders were prepared by a sol-gel process using titanium isopropoxide as a Ti precursor and cobalt, gallium, or neodymium as a dopant. For the prepared doped TiO₂ nanopowders, the photocatalytic behaviors in the decomposition of aqueous 1,4-dichlorobenzene (DCB) were investigated as a function of doping level and preparation conditions. We found that all of the metal ion doping improved the photocatalytic activity of TiO₂, though Nd doping was the most effective and Co doping was least effective. XRD analyses showed that doping with Ga and Nd ions suppresses the anatase-to-rutile phase transition for TiO₂, whereas doping with Co did not influence the phase transition. The UV-visible absorption spectra for these metal-ion-doped samples were red-shifted by ∼ 20–40 nm depending upon the doping level.Original English Text Copyright © 2005 by Fizika i Khimiya Stekla, Whang, J. Kim, E. Kim, Y. Kim, Lee.This article was submitted by the authors in English.     

Preparation of TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hollow spheres and their activity in methylene blue photodecomposition

PSA [poly-(styrene-methyl acrylic acid)] latex particle has been taken into account as template material in SiO₂ hollow spheres preparation. TiO₂-doped SiO₂ hollow spheres were obtained by using the appropriate amount of Ti(SO₄)₂ solution on SiO₂ hollow spheres. The photodecomposition of the MB (methylene blue) was evaluated on these TiO₂-doped SiO₂ hollow spheres under UV light irradiation. The catalyst samples were characterized by XRD, UV-DRS, SEM and BET. A TiO₂-doped SiO₂ hollow sphere has shown higher surface area in comparison with pure TiO₂ hollow spheres. The 40 wt% TiO₂-doped SiO₂ hollow sphere has been found as the most active catalyst compared with the others in the process of photodecomposition of MB (methylene blue). The BET surface area of this sample was found to be 377.6 m²g⁻¹. The photodegradation rate of MB using the TiO₂-doped SiO₂ catalyst was much higher than that of pure TiO₂ hollow spheres.     

Phase evolution during mechanochemical coreduction of V<Subscript>2</Subscript>O<Subscript>5</Subscript> and TiO<Subscript>2</Subscript> with A

The direct preparation of V-Ti solid solution alloy by coreduction of V₂O₅ and TiO₂ with Al in an attritor mill was investigated. The reduction of V₂O₅ with Al is highly exothermic, whereas reduction of TiO₂ with Al is not sufficiently exothermic for a self-sustaining reaction. A range of compositions of a mixture of V₂O₅ and TiO₂ can be so chosen as to make the overall reduction of V₂O₅ and TiO₂ with Al sufficiently exothermic for a self-sustaining reaction. Initial studies were done to identify the reaction products obtained by reducing V₂O₅ with Al. The reaction yielded the intermetallic phase (Al₃V), V, and Al₂O₃. SEM images indicated melting and solidification of the phases, leading to agglomeration. Further experiments involved mixing appropriate amounts of TiO₂ with V₂O₅ and reducing the mixture with Al. XRD data for products showed the presence of V, V₅Al₈, and Al₂O₃. X-Ray Florescence (XRF) analysis and energy dispersive analyzer (EDAX) of SEM sample images indicated the formation of V-Ti solid solution. Microstructure of the milled charges taken out prior to reaction initiation indicated morphology change in Al powder and agglomeration/segregation of reactants. As a result, the reaction of V₂O₅ with the excess Al at certain regions also promoted the formation of vanadium aluminide.     

Some characteristics of heat-resisting concretes modified by SiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript> nanoparticles

Nanoparticles of SiO₂ or TiO₂ have been added in the preparation of heat-resisting concretes of two types. The major technical and chemical characteristics have been determined. Features have been found in some of the technological operations in making the concretes of both types, and also aspects of the physicomechanical properties. Higher chemical stability has been found for heat-resisting concrete containing TiO₂ nanoparticles in an NaOH solution.