Nanocasting Synthesis of Mesostructured Co<Subscript>3</Subscript>O<Subscript>4</Subscript> via a Supercritical CO<Subscript>2</Subscript> Deposition Method and the Catalytic Performance for CO Oxidation

Abstract  

We demonstrate a supercritical CO₂ (scCO₂) deposition method to synthesize mesostructured Co₃O₄ with crystalline walls using SBA-15 as the hard template. By variation of the scCO₂ pressure, randomly organized nanorods or a highly ordered mesoporous structure of Co₃O₄ is obtained after only one filling operation. The catalytic tests show that the randomly organized Co₃O₄ nanorods display excellent activity for CO oxidation with the complete conversion of CO even at room temperature, while neither the ordered mesoporous nor bulk Co₃O₄ is active at this low-temperature, demonstrating the important role of Co₃O₄ morphology in catalysis.     

Side-by-Side In(OH)<Subscript>3</Subscript> and In<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanotubes: Synthesis and Optical Properties

A simple and mild wet-chemical approach was developed for the synthesis of one-dimensional (1D) In(OH)₃ nanostructures. By calcining the 1D In(OH)₃ nanocrystals in air at 250 °C, 1D In₂O₃ nanocrystals with the same morphology were obtained. TEM results show that both 1D In(OH)₃ and 1D In₂O₃ are composed of uniform nanotube bundles. SAED and XRD patterns indicate that 1D In(OH)₃ and 1D In₂O₃ nanostructures are single crystalline and possess the same bcc crystalline structure as the bulk In(OH)₃ and In₂O₃, respectively. TGA/DTA analyses of the precursor In(OH)₃ and the final product In₂O₃ confirm the existence of CTAB molecules, and its content is about 6%. The optical absorption band edge of 1D In₂O₃ exhibits an evident blueshift with respect to that of the commercial In₂O₃ powders, which is caused by the increasing energy gap resulted from decreasing the grain size. A relatively strong and broad purple-blue emission band centered at 440 nm was observed in the room temperature PL spectrum of 1D In₂O₃ nanotube bundles, which was mainly attributed to the existence of the oxygen vacancies.     

Preparation and characterization of mesoporous TiO<Subscript>2</Subscript> thin film

Ordered hexagonal mesoporous TiO₂ thin film was prepared by the evaporation-induced self-assembly (EISA) method using triblock copolymer (Pluronic P123) and tetrabutyl orthotitanate (Ti(OBu ⁿ )₄, TBOT) in 1-methoxy-2-propanol (C₄H₁₀O₂, PGME) solvent. The arrangement of mesopores was identified by small-angle X-ray diffraction and transmission electron microscopy (TEM). The well-ordered hexagonal mesoporous TiO₂ had a high specific surface area of 239 m²/g and an average pore size of 6.3 nm. The structure of mesoporous TiO₂ thin film was anatase with a 5.1 nm crystallite. The absorption band shift of the mesoporous TiO₂ toward longer wavelengths as calcined at 350 °C due to the residual carbon.     

Synthesis of Heterogeneous Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> Nanostructured Anodes with Long-Term Cycle Stability

The 0D-1D Lithium titanate (Li₄Ti₅O₁₂) heterogeneous nanostructures were synthesized through the solvothermal reaction using lithium hydroxide monohydrate (Li(OH)·H₂O) and protonated trititanate (H₂Ti₃O₇) nanowires as the templates in an ethanol/water mixed solvent with subsequent heat treatment. A scanning electron microscope (SEM) and a high resolution transmission electron microscope (HRTEM) were used to reveal that the Li₄Ti₅O₁₂ powders had 0D-1D heterogeneous nanostructures with nanoparticles (0D) on the surface of wires (1D). The composition of the mixed solvents and the volume ratio of ethanol modulated the primary particle size of the Li₄Ti₅O₁₂ nanoparticles. The Li₄Ti₅O₁₂ heterogeneous nanostructures exhibited good capacity retention of 125 mAh/g after 500 cycles at 1C and a superior high-rate performance of 114 mAh/g at 20C.     

Highly ordered mesoporous CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and CuFe<Subscript>2</Subscript>O<Subscript>4</Subscript> with crystalline walls

The highly ordered mesoporous CoFe₂O₄ and CuFe₂O₄ with crystalline walls can be synthesized by hard template with using mesoporous silica SBA-15 as hard template and using ferric nitrate, cobalt nitrate, and copper nitrate as metal precursors. These new mesoporous materials above have high surface areas, narrow pore size distribution, and large pore volumes, which are believed to be valuable for the potential application in the field of sensors, catalysis, message recording, magnetics, and biology. This work provides a method to fabricate the highly ordered mesoporous materials composed of multi-metal oxides with crystalline walls. The development of such versatile approach is of great significance in practical application. It can be envisaged that this established method is significantly expandable to the controlled synthesis of the mesoporous functional materials with diverse compositions.     

Zeolite Confined Ti(OH)<Subscript>4</Subscript> Nanoparticles in Highly Active and Selective Oxidation Catalyst

Abstract  

Some highly active, hydrophilic, MFI structured titanium silicate catalysts are characterized by an intense UV absorption centered in the 213–233 nm (43000–47000 cm⁻¹) range. The assignment of this band to a specific molecular structure has remained unclear unlike the well published <213 nm charge transfer excitations between the 2p lattice oxygen orbitals and the 3d orbitals of isomorphously inserted, isolated, tetrahedral Ti-atoms in TS-1 and the >233 nm UV bands of higher coordinated Ti-atoms at lattice defects or in variously agglomerated extra lattice Ti _x O _y (OH) _z species. To decipher the structural origin of this intermediate UV band, we used Time-Dependent Density Functional Theory (TD-DFT) to compute the UV spectra of various model compositions and show in this paper that only one model, in which isolated tetrahedral Ti(OH)₄ molecules reside in the zeolite channels without any covalent bond to the framework, fits the experimental UV spectrum. Hence these confined tetrahedral Ti(OH)₄ nanoparticles may account for the enhanced activity and selectivity of some MFI type titanium silicate catalysts.     

NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript>@SiO<Subscript>2</Subscript> Nanoparticles Stabilized by Porous Silica Shells

Abstract  

NiFe₂O₄ nanoparticles stabilized by porous silica shells (NiFe₂O₄@SiO₂) were prepared using a one-pot synthesis and characterized for their physical and chemical stability in severe environments, representative of those encountered in industrial catalytic reactors. The SiO₂ shell is porous, allowing transport of gases to and from the metal core. The shell also stabilizes NiFe₂O₄ at the nanoparticle surface: NiFe₂O₄@SiO₂ annealed at temperatures through 973 K displays evidence of surface Ni, as verified by H₂ TPD analyses. At 1,173 K, hematite forms at the surface of the metallic cores of the NiFe₂O₄@SiO₂ nanoparticles and surface Ni is no longer observed. Without the silica shell, however, even mild reduction (at 773 K) can draw Fe to the surface and eliminate surface Ni sites.     

Single-crystalline nanoporous Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> nanotubes

Single-crystalline nanoporous Nb₂O₅ nanotubes were fabricated by a two-step solution route, the growth of uniform single-crystalline Nb₂O₅ nanorods and the following ion-assisted selective dissolution along the [001] direction. Nb₂O₅ tubular structure was created by preferentially etching (001) crystallographic planes, which has a nearly homogeneous diameter and length. Dense nanopores with the diameters of several nanometers were created on the shell of Nb₂O₅ tubular structures, which can also retain the crystallographic orientation of Nb₂O₅ precursor nanorods. The present chemical etching strategy is versatile and can be extended to different-sized nanorod precursors. Furthermore, these as-obtained nanorod precursors and nanotube products can also be used as template for the fabrication of 1 D nanostructured niobates, such as LiNbO₃, NaNbO₃, and KNbO₃.     

Sorption studies of CO<Subscript>2</Subscript>, CH<Subscript>4</Subscript>, N<Subscript>2</Subscript>, CO,O<Subscript>2</Subscript> and Ar on nanoporous aluminum terephthalate [MIL-53(Al)]

Aluminum terephthalate, MIL-53(Al), metal–organic framework synthesized hydrothermally and purified by solvent extraction method was used as an adsorbent for gas adsorption studies. The synthesized MIL-53(Al) was characterized by powder X-Ray diffraction analysis, surface area measurement using N₂ adsorption–desorption at 77 K, FTIR spectroscopy and thermo gravimetric analysis. Adsorption isotherms of CO₂, CH₄, CO, N₂, O₂ and Ar were measured at 288 and 303 K. The absolute adsorption capacity was found in the order CO₂>CH₄>CO>N₂>Ar>O₂. Henry’s constants, heat of adsorption in the low pressure region and adsorption selectivities for the adsorbate gases were calculated from their adsorption isotherms. The high selectivity and low heat of adsorption for CO₂ suggests that MIL-53(Al) is a potential adsorbent material for the separation of CO₂ from gas mixtures. The high selectivity for CH₄ over O₂ and its low heat of adsorption suggests that MIL-53(Al) could also be a compatible adsorbent for the separation of methane from methane–oxygen gas mixtures.     

Preparation of MCM-41 Supported Salen Vanadium Complex and its Catalysis for the Oxidation of Cyclohexane with H<Subscript>2</Subscript>O<Subscript>2</Subscript> as an Oxidant

A secondary amino group modified MCM-41 (mobile crystalline material number 41) was synthesized and used as a support for the immobilization of a salen oxovanadium complex via a multi-grafting method. The immobilized complex was characterized by UV–Vis spectroscopy, X-ray diffraction (XRD), N₂ adsorption and ICP analysis techniques. The immobilized complex was found to be an effective catalyst for oxidation of cyclohexane using H₂O₂ as an oxidant under mild conditions. A conversion of 45.5% of cyclohexane was obtained with a selectivity of 100% of the cyclohexanone/cyclohexanol mixture when the reaction was run at 60 °C for 12 h in acetonitrile. Decomposition of the complex, which leads to the deactivation of the catalyst, is observed and a decomposition mechanism is discussed.     

Aqueous-Phase Hydrogenolysis of Glycerol to 1,3-propanediol Over Pt-H<Subscript>4</Subscript>SiW<Subscript>12</Subscript>O<Subscript>40</Subscript>/SiO<Subscript>2</Subscript>

Abstract  

Hydrogenolysis of glycerol to 1,3-propanediol in aqueous-phase was investigated over Pt-H₄SiW₁₂O₄₀/SiO₂ bi-functional catalysts with different H₄SiW₁₂O₄₀ (HSiW) loading. Among them, Pt-15HSiW/SiO₂ showed superior performance due to the good dispersion of Pt and appropriate acidity. It is found that Br?nsted acid sites facilitate to produce 1,3-PDO selectively confirmed by Py-IR. The effects of weight hourly space velocity, reaction temperature and hydrogen pressure were also examined. The optimized Pt-HSiW/SiO₂ catalyst showed a 31.4% yield of 1,3-propanediol with glycerol conversion of 81.2% at 200 °C and 6 MPa.     

Nanocasting Synthesis of Ultrafine WO<Subscript>3</Subscript> Nanoparticles for Gas Sensing Applications

Ultrafine WO₃ nanoparticles were synthesized by nanocasting route, using mesoporous SiO₂ as a template. BET measurements showed a specific surface area of 700 m²/gr for synthesized SiO_2, while after impregnation and template removal, this area was reduced to 43 m²/gr for WO3 nanoparticles. HRTEM results showed single crystalline nanoparticles with average particle size of about 5 nm possessing a monoclinic structure, which is the favorite crystal structure for gas sensing applications. Gas sensor was fabricated by deposition of WO₃ nanoparticles between electrodes via low frequency AC electrophoretic deposition. Gas sensing measurements showed that this material has a high sensitivity to very low concentrations of NO₂ at 250°C and 300°C.     

Crystallization Behavior of Amorphous Zr<Subscript>55</Subscript>Cu<Subscript>20</Subscript>Ni<Subscript>10</Subscript>Al<Subscript>10</Subscript>Ti<Subscript>5</Subscript> Alloy

In the present study, the crystallization behavior and thermal stability of amorphous Zr₅₅Cu₂₀Ni₁₀Al₁₀Ti₅ alloy, obtained by melt-spinning, have been investigated using X-ray diffraction (XRD), differential thermal analysis (DTA) and transmission electron microscopy (TEM). The activation energy for crystallization has been evaluated by the Kissinger method, and it has been found that E _x obtained from the crystallization onset temperature (T _x) is lower than E _p determined by the crystallization peak temperature (T _P). During the continuous annealing process, ZrO and h-Al₃Zr₅ phases firstly precipitate from the amorphous matrix, then Zr₂Ni_0.66O_0.33 phase forms continuously and its relative content increases with increasing annealing temperature. However, no crystalline phases have been observed during the isothermal annealing process at 733 K (below T _x) for 90 min. The atomic clusters can keep the stability state through adjusting the short-range ordering.     

Effects of surface area on electrochemical performance of Li[Ni<Subscript>0.2</Subscript>Li<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>]O<Subscript>2</Subscript> cathode material

The effect of surface area on the electrochemical properties and thermal stability of Li[Ni_0.2Li_0.2Mn_0.6]O₂ powders was characterized using a charge/discharge cycler and DSC (Differential Scanning Calorimeter). The surface area of the samples was successfully controlled from ~4.0 to ~11.7 m² g⁻¹ by changing the molar ratio of the nitrate/acetate sources and adding an organic solvent such as acetic acid or glucose. The discharge capacity and rate capability was almost linearly increased with increase in surface area of the sample powder. A sample with a large surface area of 9.6–11.7 m² g⁻¹ delivered a high discharge capacity of ~250 mAh g⁻¹ at a 0.2 C rate and maintained 62–63% of its capacity at a 6 C rate versus a 0.2 C rate. According to the DSC analysis, heat generation by thermal reaction between the charged electrode and electrolyte was not critically dependent on the surface area. Instead, it was closely related to the type of organic solvent employed in the fabrication process of the powder.     

Synthesis of Submicron Nanocrystalline Y<Subscript>2</Subscript>O<Subscript>3</Subscript>: Eu Particles via Solvothermal Approach Using Surface Modifiers

In this paper, solvothermal synthesis of submicron nanocrystalline Y₂O₃: Eu particles with and without surface modifier (β-alanine and Tween-80) is investigated. X-ray diffraction ananlysis confirms the one-step formation of Y₂(OH)₅NO₃H₂O phase during solvothermal process and its conversion to Y₂O₃: Eu after heat treatment at 600 °C. Fourier transformation infrared spectroscopy showed that C=C, C–C and C–H peaks are corresponded to the surface modifiers i.e. tween-80 and β-alanine. Scanning electron microscopy and transmission electron microscopy images also showed that the modifier results in the particle morphology improvement from sheet-like to submicron spherical particles. Photoluminescence experiments indicated that the emission intensity increases due to the morphology modification.     

Effects of La<Subscript>2</Subscript>O<Subscript>3</Subscript> on ZrO<Subscript>2</Subscript> supported Ni catalysts for autothermal reforming of CH<Subscript>4</Subscript>

The effect of La₂O₃ content in Ni-La-Zr catalyst was investigated for the autothermal reforming (ATR) of CH₄. The catalysts were prepared by the coprecipitation method and had a mesoporous structure. Temperature programmed reduction (TPR) and X-ray photoelectron spectroscopy (XPS) indicated that a strong interaction developed between Ni species and the support with the addition of La₂O₃. Thermogravimetric analysis (TGA) and H₂-pulse chemisorption showed that the addition of La₂O₃ led to well dispersed NiO molecules on the support. Ni-La-Zr catalysts gave much higher CH₄ conversion than Ni-Zr catalyst. The Ni-La-Zr containing 3.2 wt% La₂O₃ showed the highest activity. The optimum conditions for maximal CH₄ conversion and H₂ yield were H₂O/CH₄=1.00, O₂/CH₄=0.75. Under these conditions, CH₄ conversion of 83% was achieved at 700 °C. In excess O₂ (O₂/CH₄>0.88), the catalytic activity was decreased due to sintering of the catalyst.     

Synthesis of Highly Active Nano-Sized Pt/CeO<Subscript>2</Subscript> Catalyst via a Cerium Hydroxy Carbonate Precursor for Water Gas Shift Reaction

Abstract  

A novel precipitation/digestion route has been developed to synthesize crystalline cerium hydroxy carbonate (CHC: Ce(OH)CO₃) by using an equimolar quantity of cerium nitrate (Ce(NO₃)₃·6H₂O) and mixed precipitants (KOH + K₂CO₃) at room temperature. Nano-sized CeO₂ supports could be prepared by the pre-calcination of CHC at 400 °C for 4 h. A highly active water gas shift (WGS) catalyst, 1 wt.% Pt/CeO₂ catalyst showed almost equilibrium CO conversion with 100% CO₂ selectivity at 320 °C even at the gas hourly space velocity (GHSV) of 45,625 h⁻¹.     

Preparation and Characterization of Mesoporous MoO<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> Composite with High Surface Area by Self-Supporting and Ammonia Method

Abstract  

A mesoporous MoO₃/TiO₂ composite was prepared from titanate derivative by consecutive self-supporting and ammonia method. All samples were characterized by X-ray Diffraction, N₂ adsorption–desorption, Raman Spectra and Field-Emission Scanning Electron Microscopy. The results showed that mesoporous MoO₃/TiO₂ composite had a higher surface area (173 m²/g) and a better MoO₃ dispersion than that prepared by traditional impregnation (90 m²/g). As for hydrodesulfurization tests, mesoporous MoO₃/TiO₂ composite in this case presented a better catalytic performance, attributed to its high surface area and good dispersion of MoO₃. It can be found that self-supporting played a key role in preparing mesoporous MoO₃/TiO₂ composite with high surface area. Additionally, aqueous ammonia could effectively dissolve excess MoO₃, which helped to obtain mesoporous MoO₃/TiO₂ composite with better dispersion of MoO₃.     

Promoting Effect of Triglyme on Lean NO<Subscript>x</Subscript> Reduction Over Ag/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

Abstract  

The highly oxygenated hydrocarbon triethylene glycol dimethyl ether or triglyme (CH₃O–(C₂H₄O–)₃CH₃) was found to efficiently reduce NO_x under lean conditions over Ag/Al₂O₃, but gave a low NO_x conversion over Cu-ZSM-5. Furthermore, triglyme showed an extraordinary promoting effect when added together with propene as reducing agent for NO_x over Ag/Al₂O₃ at low temperature. This is most likely due to that triglyme promotes the activation of propene.     

Preparation of CuO-CeO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst with mesopore structure for water gas shift reaction

The water gas shift (WGS) reaction has been investigated widely in fuel cell technologies due to the potential for high fuel efficiency and lower emissions during the production of pure hydrogen. Industrially, the WGS reaction occurs in one of the following two ways: (a) high-temperature in the range of 310–450°C with Fe-Cr catalyst, (b) low-temperature in the range of 210–250°C with Cu-ZnO-Al₂O₃. In this study, a mesoporous catalyst was prepared, with a large surface area and uniformity in both pore size and distribution, by using a one-pot synthesis method. The prepared CuO-CeO₂-Al₂O₃ brought high CO conversion (82%), and was suitable for WGS reaction at low temperature (250 °C). This article is dedicated to Professor Chang Kyun Choi for celebrating his retirement from the School of Chemical and Biological Engineering, Seoul National University.