Chemical and electrochemical characterization of TiO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> atomic layer depositions on AZ-31 magnesium alloy

In this study, innovative TiO₂/Al₂O₃ mono/multilayers were applied by atomic layer depositions (ALD) on ASTM-AZ-31 magnesium/aluminum alloy to enhance its well-known scarce corrosion resistance. Four different configurations of ALD layers were tested: single TiO₂ layer, single Al₂O₃ layer, Al₂O₃/TiO₂ bilayer and Al₂O₃/TiO₂/Al₂O₃/TiO₂ multilayer deposited using Al[(CH₃)]₃ (trimethylaluminum, TMA), and TiCl₄ and H₂O precursors. All depositions were performed at 120°C to obtain an amorphous-like structure of both oxide layers. The four coatings were then investigated using different techniques, such as scanning electron microscope (SEM), stylus profilometer, glow discharge optical emission spectrometry (GDOES) and polarization curves in 0.05-M NaCl solution. The thickness of all the coatings was around 100 nm. The layers compositions were successfully investigated by the GDOES technique, although obtained data seem to be affected by substrate roughness and differences in sputtering rates between ceramic oxides and metallic magnesium alloy. Corrosion resistance showed to be strongly enhanced by the nanometric coatings, giving lower corrosion current densities in 0.05-M NaCl media with respect to the uncoated substrate (from 10⁻⁴ to 10⁻⁶ A/cm² for the single layers and from 10⁻⁴ to 10⁻⁸ A/cm² for the bi- and multilayers). All polarization curves on coated samples also showed a passive region, wider for the bi-layer (from −0.58 to −0.43 V with respect to Ag/AgCl) and multilayer (from −0.53 to −0.38 V with respect to Ag/AgCl) structures.     

Epoxidation of Propylene on a [Ag<Subscript>14</Subscript>O<Subscript>9</Subscript>] Cluster Representing Ag<Subscript>2</Subscript>O (001) Surface: A Density Functional Theory Study

Abstract  

Density functional theory calculations were employed to study partial oxidation of propylene on a [Ag₁₄O₉] cluster representing Ag₂O (001) surface for which positive effect for ethylene oxide formation has been reported in our earlier work at the same level of theory (Fellah et al., Catal Lett 141:762, 2011). Propylene oxide (PO), propanal, acetone and П-allyl radical formation reaction mechanisms were investigated. Π-allyl formation path and two propylene adsorption paths resulting in PO formation are competing reactions on silver oxide (001) surface because of their comparable activation barriers (9, 8 and 9 kcal/mol, respectively) while Π-allyl formation path is generally a more favorable path on Ag (111) surface as reported in previous theoretical literature. SO₂ adsorption calculations indicate that silver oxide has lower Lewis basicity relative to oxygen atom adsorbed on silver. Calculations also showed that surface oxygen atom of Ag₂O (001) has a higher spin density compared to that of oxygen atom adsorbed on Ag (111), which indicates that oxygen atom on Ag₂O (001) cluster has a more radical character.     

Temperature programmed desorption of oxygen from Pd films interfaced with Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-doped ZrO<Subscript>2</Subscript>

The origin of the effect of non-faradaic electrochemical modification of catalytic activity (NEMCA) or Electrochemical Promotion was investigated via temperature-programmed-desorption (TPD) of oxygen, from polycrystalline Pd films deposited on 8 mol%Y₂O₃–stabilized–ZrO₂ (YSZ), an O²⁻ conductor, under high-vacuum conditions and temperatures between 50 and 250 °C. Oxygen was adsorbed both via the gas phase and electrochemically, as O²⁻, via electrical current application between the Pd catalyst film and a Au counter electrode. Gaseous oxygen adsorption gives two adsorbed atomic oxygen species desorbing at about 300 °C (state β₁) and 340–500 °C (state β₂). The creation of the low temperature peak is favored at high exposure times (exposure >1 kL) and low adsorption temperatures (T_ads < 200 °C). The decrease of the open circuit potential (or catalyst work function) during the adsorption at high exposure times, indicates the formation of subsurface oxygen species which desorbs at higher temperatures (above 450 °C). The desorption peak of this subsurface oxygen is not clear due to the wide peaks of the TPD spectra. The TPD spectra after electrochemical O²⁻ pumping to the Pd catalyst film show two peaks (at 350 and 430 °C) corresponding to spillover O_ads and according to the reaction:

The role of TiO<Subscript>2</Subscript> layers deposited on YSZ on the electrochemical promotion of C<Subscript>2</Subscript>H<Subscript>4</Subscript> oxidation on Pt

The electrochemical promotion of Pt/YSZ and Pt/TiO₂/YSZ catalyst-electrodes has been investigated for the model reaction of C₂H₄ oxidation in an atmospheric pressure single chamber reactor, under oxygen excess between 280 and 375 °C. It has been found that the presence of a dispersed TiO₂ thin layer between the catalyst electrode and the solid electrolyte (YSZ), results in a significant increase of the magnitude of the electrochemical promotion of catalysis (EPOC) effect. The rate enhancement ratio upon current application and the faradaic efficiency values, were found to be a factor of 2.5 and 4 respectively, higher than those in absence of TiO₂. This significantly enhanced EPOC effect via the addition of TiO₂ suggests that the presence of the porous TiO₂ layer enhances the transport of promoting O²⁻ species onto the Pt catalyst surface. This enhancement may be partly due to morphological factors, such as increased Pt dispersion and three-phase-boundary length in presence of the TiO₂ porous layer, but appears to be mainly caused by the mixed ionic-electronic conductivity of the TiO₂ layer which results to enhanced O²⁻ transport to the Pt surface via a self-driven electrochemical promotion O²⁻ transport mechanism.     

Preparation and Characterization of Mesoporous MoO<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> Composite with High Surface Area by Self-Supporting and Ammonia Method

Abstract  

A mesoporous MoO₃/TiO₂ composite was prepared from titanate derivative by consecutive self-supporting and ammonia method. All samples were characterized by X-ray Diffraction, N₂ adsorption–desorption, Raman Spectra and Field-Emission Scanning Electron Microscopy. The results showed that mesoporous MoO₃/TiO₂ composite had a higher surface area (173 m²/g) and a better MoO₃ dispersion than that prepared by traditional impregnation (90 m²/g). As for hydrodesulfurization tests, mesoporous MoO₃/TiO₂ composite in this case presented a better catalytic performance, attributed to its high surface area and good dispersion of MoO₃. It can be found that self-supporting played a key role in preparing mesoporous MoO₃/TiO₂ composite with high surface area. Additionally, aqueous ammonia could effectively dissolve excess MoO₃, which helped to obtain mesoporous MoO₃/TiO₂ composite with better dispersion of MoO₃.     

Facile synthesis of nano-Li<Subscript>4</Subscript> Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> for high-rate Li-ion battery anodes

One of the most promising anode materials for Li-ion batteries, Li₄Ti₅O₁₂, has attracted attention because it is a zero-strain Li insertion host having a stable insertion potential. In this study, we suggest two different synthetic processes to prepare Li₄Ti₅O₁₂ using anatase TiO₂ nanoprecursors. TiO₂ powders, which have extraordinarily large surface areas of more than 250 m² g^-1, were initially prepared through the urea-forced hydrolysis/precipitation route below 100°C. For the synthesis of Li₄Ti₅O₁₂, LiOH and Li₂CO₃ were added to TiO₂ solutions prepared in water and ethanol media, respectively. The powders were subsequently dried and calcined at various temperatures. The phase and morphological transitions from TiO₂ to Li₄Ti₅O₁₂ were characterized using X-ray powder diffraction and transmission electron microscopy. The electrochemical performance of nanosized Li₄Ti₅O₁₂ was evaluated in detail by cyclic voltammetry and galvanostatic cycling. Furthermore, the high-rate performance and long-term cycle stability of Li₄Ti₅O₁₂ anodes for use in Li-ion batteries were discussed.     

Experimental and theoretical analysis of element mercury adsorption on Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Ag composites

A novel magnetic nano-sorbent Fe₃O₄/Ag was synthesized and applied to capture the elemental mercury from the simulated flue gas. The morphology, components and crystal phase of the sorbents were characterized by transmission electron microscope (TEM), energy dispersive spectrometry (EDS) and X-ray diffraction (XRD), respectively. The mercury removal performance of the sorbents was investigated through the fixed-bed tests. The results indicated that silver was successfully loaded on the surface of Fe₃O₄ particles, which could significantly enhance the Hg⁰ removal performance of the sorbents. Flue gas components, including CO₂, SO₂, and NO, have little impact on the Hg⁰ removal performance of Fe₃O₄/Ag sorbents, while O₂ has a slightly positive effect. The Hg⁰ removal efficiency decreased with the increasing of temperature, Hg⁰ inlet concentration and gas hourly space velocity. Only one broad mercury desorption peak at approximately 210 °C could be observed during the temperature-programmed desorption (TPD) process, which indicated that mercury species existing on the surface of Fe₃O₄/Ag sorbents might be elemental mercury instead of oxidized mercury. Furthermore, the reusability tests showed that the Fe₃O₄/Ag sorbents could be efficiently regenerated and reused. Finally, the theoretical analysis based on the DFT method showed that a weak chemisorption of Hg⁰ on Fe₃O₄ sorbents changed to a strong chemisorption when silver was loaded. The results of theoretical analysis conformed to the experiments results well.     

Promoting Effect of Triglyme on Lean NO<Subscript>x</Subscript> Reduction Over Ag/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

Abstract  

The highly oxygenated hydrocarbon triethylene glycol dimethyl ether or triglyme (CH₃O–(C₂H₄O–)₃CH₃) was found to efficiently reduce NO_x under lean conditions over Ag/Al₂O₃, but gave a low NO_x conversion over Cu-ZSM-5. Furthermore, triglyme showed an extraordinary promoting effect when added together with propene as reducing agent for NO_x over Ag/Al₂O₃ at low temperature. This is most likely due to that triglyme promotes the activation of propene.     

TiO<Subscript>2</Subscript>/Ni Inverse-Catalysts Prepared by Atomic Layer Deposition (ALD)

Abstract  

Atomic layer deposition (ALD) was used to deposit TiO₂ on Ni particles, and the catalytic activity of Ni for CO₂ reforming of methane (CRM) was evaluated. In the presence of TiO₂ islands on Ni surfaces, the onset temperature of the CRM reaction was lower than that of bare Ni. During the CRM reaction, carbon was deposited on the surface of bare Ni, which reduced the catalytic activity of the surface with time, and TiO₂ islands were able to remove carbon deposits from the surface. When the Ni surface was completely covered with TiO₂, the catalytic activity disappeared, demonstrating that tuning of the TiO₂ coverage on Ni is important to maximize the activity of the CRM reaction.     

Oxygen permeability and structural stability of La<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>Co<Subscript>0.2</Subscript>Fe<Subscript>0.8</Subscript>O<Subscript>3−<Emphasis Type="Italic">δ</Emphasis></Subscript> membrane

La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ oxides were synthesized by citrate method and hydrothermal method. The oxides prepared by citrate method are perovskite type structure, while the oxides by hydrothermal method have a small amount of secondary phase in the powder. Pyrex glass seal and Ag melting seal provided reliable gas-tight sealing of disk type dense membrane in the range of operation temperature, but commercial ceramic binder could not be removed from the support tube without damage to the tube or membrane. Though the degree of gas tightness increases in the order of glass>Ag>ceramic binder, in the case of glass seal, the undesired spreading of glass leads to an interfacial reaction between it and the membrane and reduction of effective permeation area. The oxygen flux of La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ membrane increases with increasing temperature and decreasing thickness, and the oxygen permeation flux through 1.0 mm membrane exposed to flowing air (P _h =0.21 atm) and helium (P₁=0.037 atm) is ca. 0.33 ml/cm²·min at 950 °C. X-ray diffraction analysis for the membrane after permeation test over 160 h revealed that La₂O₃ and unknown compound were formed on the surface of membrane. The segregation compounds of surface elements formed on both surfaces of membrane irrespective of spreading of glass sealing material. This paper was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

CO<Subscript>2</Subscript> retention ability on alkali cation exchanged titanium silicate,ETS-10

ETS-10 was ion exchanged by various alkali cations (Li⁺, Na⁺, K⁺, Rb⁺ and Cs⁺) and the BET surface area and pore volume was exactly consistent with cationic size; that is, in the order of Li⁺ > Na⁺ > K⁺ > Rb⁺ > Cs⁺. It was observed that a single point adsorption capacity was inversely proportional to cationic size. The largest CO₂ capacity was observed for Li⁺-ETS-10 and it is attributed to greater cation–quadrupole interactions with CO₂ than larger cation. The results also suggests that as the CO₂ loading is increased, the accessibility of adsorbing CO₂ to framework basic O⁻ sites should have become difficult with the increase in cationic size due to the blocking effect by extra-framework CO₂-M⁺. The slight decrease in the slope of adsorption capacity with temperature, especially beyond 373 K for Li⁺-ETS-10 and K⁺-ETS-10 suggests that the adsorption of CO₂ on small alkali cation exchanged-ETS-10 at high temperature is somewhat associated with basic oxygen anion sites in framework due to the existence of large pore. The CO₂-TPD results show that the amount of desorbed CO₂ at higher temperature was proportionally increased due to the increased basicity of oxygen anions in framework. It also shows that the desorption temperature associated with alkali cations in extra-framework (corresponding to low temperature desorption peak) has been lowered with the increase in cationic size, indicating weak cation–quadrupole interactions with CO₂ for larger cations.     

Sorption studies of CO<Subscript>2</Subscript>, CH<Subscript>4</Subscript>, N<Subscript>2</Subscript>, CO,O<Subscript>2</Subscript> and Ar on nanoporous aluminum terephthalate [MIL-53(Al)]

Aluminum terephthalate, MIL-53(Al), metal–organic framework synthesized hydrothermally and purified by solvent extraction method was used as an adsorbent for gas adsorption studies. The synthesized MIL-53(Al) was characterized by powder X-Ray diffraction analysis, surface area measurement using N₂ adsorption–desorption at 77 K, FTIR spectroscopy and thermo gravimetric analysis. Adsorption isotherms of CO₂, CH₄, CO, N₂, O₂ and Ar were measured at 288 and 303 K. The absolute adsorption capacity was found in the order CO₂>CH₄>CO>N₂>Ar>O₂. Henry’s constants, heat of adsorption in the low pressure region and adsorption selectivities for the adsorbate gases were calculated from their adsorption isotherms. The high selectivity and low heat of adsorption for CO₂ suggests that MIL-53(Al) is a potential adsorbent material for the separation of CO₂ from gas mixtures. The high selectivity for CH₄ over O₂ and its low heat of adsorption suggests that MIL-53(Al) could also be a compatible adsorbent for the separation of methane from methane–oxygen gas mixtures.     

Preparation and characterization of mesoporous TiO<Subscript>2</Subscript> thin film

Ordered hexagonal mesoporous TiO₂ thin film was prepared by the evaporation-induced self-assembly (EISA) method using triblock copolymer (Pluronic P123) and tetrabutyl orthotitanate (Ti(OBu ⁿ )₄, TBOT) in 1-methoxy-2-propanol (C₄H₁₀O₂, PGME) solvent. The arrangement of mesopores was identified by small-angle X-ray diffraction and transmission electron microscopy (TEM). The well-ordered hexagonal mesoporous TiO₂ had a high specific surface area of 239 m²/g and an average pore size of 6.3 nm. The structure of mesoporous TiO₂ thin film was anatase with a 5.1 nm crystallite. The absorption band shift of the mesoporous TiO₂ toward longer wavelengths as calcined at 350 °C due to the residual carbon.     

Effects of adding B<Subscript>2</Subscript>O<Subscript>3</Subscript> as a flux on phosphorescent properties in synthesis of SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript>: (Eu<Superscript>2+</Superscript>, DY<Superscript>3+</Superscript> phosphor

SrAl₂O₄: (Eu²⁺, Dy³⁺) phosphor was prepared by solid state reaction. B₂O₅ as a flux was added in SrAl₂O₄:(Eu ²⁺, Dy³⁺) in order to accelerate a solid state reaction. In this paper, the effects of B₂O₃ on the crystal structure and the phosphorescent properties of the material have been evaluated. The synthesized phosphor exhibited a broad band emission spectrum peaking at 520 nm, and the spectrum peak showed little effect by the B₂O₃ contents. The maximum afterglow intensity of the SrAl₂O₄: (Eu²⁺, Dy³⁺) phosphor was obtained at the B₂O₃ content of 5%. Adding the B₂O₃ caused uniform distortion to the crystal structure of the phosphor and resulted in reducing the lengths of a and c axes and Β angle of the SrAl₂O₄ crystal. The uniform distortion was accompanied with crystal defects which can trap the holes generated by the excitation of Eu²⁺ ions. The afterglow characteristic of the SrAl₂O₄: (Eu²⁺, Dy³⁺) phosphor was thus enhanced.     

Separation characteristics of tetrapropylammoniumbromide templating silica/alumina composite membrane in CO<Subscript>2</Subscript>/N<Subscript>2</Subscript>, CO<Subscript>2</Subscript>/H<Subscript>2</Subscript> and CH<Subscript>4</Subscript>/H<Subscript>2</Subscript> systems

Nanoporous silica membrane without any pinholes and cracks was synthesized by organic templating method. The tetrapropylammoniumbromide (TPABr)-templating silica sols were coated on tubular alumina composite support ( γ-Al₂O₃/ α-Al₂O₃ composite) by dip coating and then heat-treated at 550 °C. By using the prepared TPABr templating silica/alumina composite membrane, adsorption and membrane transport experiments were performed on the CO₂/N₂, CO₂/H₂ and CH₄/H₂ systems. Adsorption and permeation by using single gas and binary mixtures were measured in order to examine the transport mechanism in the membrane. In the single gas systems, adsorption characteristics on the α-Al₂O₃ support and nanoporous unsupport (TPABr templating SiO₂/ γ-Al₂O₃ composite layer without α-Al₂O₃ support) were investigated at 20–40 °C conditions and 0.0–1.0 atm pressure range. The experimental adsorption equilibrium was well fitted with Langmuir or/and Langmuir-Freundlich isotherm models. The α-Al₂O₃ support had a little adsorption capacity compared to the unsupport which had relatively larger adsorption capacity for CO₂ and CH₄. While the adsorption rates in the unsupport showed in the order of H₂> CO₂> N₂> CH₄ at low pressure range, the permeate flux in the membrane was in the order of H₂≫N₂> CH₄> CO₂. Separation properties of the unsupport could be confirmed by the separation experiments of adsorbable/non-adsorbable mixed gases, such as CO₂/H₂ and CH₄/H₂ systems. Although light and non-adsorbable molecules, such as H₂, showed the highest permeation in the single gas permeate experiments, heavier and strongly adsorbable molecules, such as CO₂ and CH₄, showed a higher separation factor (CO₂/H₂=5-7, CH₄/H₂=4-9). These results might be caused by the surface diffusion or/and blocking effects of adsorbed molecules in the unsupport. And these results could be explained by surface diffusion. This paper is dedicated to Professor Hyun-Ku Rhee on the occasion of his retirement from Seoul National University.     

Detection of CO<Subscript>2</Subscript> and O<Subscript>2</Subscript> by iron loaded LTL zeolite films

Detection of oxygen and carbon dioxide is important in the field of chemical and biosensors for atmosphere and biosystem monitoring and fermentation processes. The present study reports on the preparation of zeolite films doped with iron nanoparticles for detection of CO₂ and O₂ in gas phase. Pure nanosized LTL type zeolite with monomodal particle size distribution loaded with iron (Fe-LTL) was prepared under hydrothermal condition from colloidal precursor suspensions. The zeolite was loaded with iron to different levels by ion exchange. The Fe-LTL suspensions were used for preparation of thin films on silicon wafers via spin coating method. The reduction of the iron in the zeolite films was carried out under H₂ flow (50% H₂ in Ar) at 300 °C. The presence of iron nanoparticles is proved by in situ ultra-violet-visible spectroscopy. The properties of the films including surface roughness, thickness, porosity, and mechanical stability were studied. In addition, the loading and distribution of iron in the zeolite films were investigated. The Fe-LTL zeolite films were used to detect O₂ and CO₂ in a concentration dependent mode, followed by IR spectroscopy. The changes in the IR bands at 855 and 642 cm^–1 (Fe?O?H and Fe?O bending vibrations) and at 2363 and 2333 cm^–1 (CO₂ asymmetric stretching) corresponding to the presence of O₂ and CO₂, respectively, were evaluated. The response to O₂ and CO₂ was instant, which was attributed to great accessibility of the iron in the nanosized zeolite crystals. The saturation of the Fe-LTL films with CO₂ and O₂ at each concentration was reached within less than a minute. The Fe-LTL films detected both oxygen and carbon dioxide in contrast, to the pure LTL zeolite film.

Open image in new window

     

Effects of preparation methods for V<Subscript>2</Subscript>O<Subscript>5</Subscript>-TiO<Subscript>2</Subscript> aerogel catalysts on the selective catalytic reduction of NO with NH<Subscript>3</Subscript>

A series of V₂O₅-TiO₂ aerogel catalysts were prepared by the sol-gel method with subsequent supercritical drying with CO₂. The main variables in the sol-gel method were the amounts of V₂O₅ and when the vanadium precursor was introduced. V₂O₅-TiO₂ xerogel and V₂O₅/TiO₂ (P-25) were also prepared for comparison. The V₂O₅-TiO₂ aerogel catalysts showed much higher surface areas and total pore volumes than V₂O₅-TiO₂ xerogel and impregnated V₂O₅/TiO₂ (P-25) catalysts. The catalysts were characterized by N₂ physisorption, X-ray diffraction (XRD), FT-Raman spectroscopy, temperature-programmed reduction with H₂ (H₂-TPR), and temperature-programmed desorption of ammonia (NH₃-TPD). The selective catalytic reduction of NOx with ammonia in the presence of excess O₂ was studied over these catalysts. Among various V₂O₅-TiO₂ catalysts, V₂O₅ supported on aerogel TiO₂ showed a wide temperature window exhibiting high NOx conversions. This superior catalytic activity is closely related to the large amounts of strong acidic sites as well as the surface vanadium species with characteristics such as easy reducibility and monomeric and polymeric vanadia surface species. This work was presented at the 7 ^th Korea-China Workshop on Clean Energy Technology held at Taiyuan, Shanxi, China, June 26–28, 2008.     

Influence of operating temperature on CO<Subscript>2</Subscript>-NH<Subscript>3</Subscript> reaction in an aqueous solution

Although aqueous ammonia solution has been focused on the removal of CO₂ from flue gas, there have been very few reports regarding the underlying analysis of the reaction between CO₂ and NH₃. In this work, we explored the reaction of CO₂-NH₃-H₂O system at various operating temperatures: 40 °C, 20 °C, and 5 °C. The CO₂ removal efficiency and the loss of ammonia were influenced by the operating temperatures. Also, infrared spectroscopy measurement was used in order to understand the formation mechanism of ion species in absorbent, such as NH₂COO⁻, HCO₃⁻, CO₃²⁻, and NH₄⁺, during CO₂, NH₃, and H₂O reaction. The reactions of CO₂-NH₃-H₂O system at 20 °C and 40 °C have similar reaction routes. However, a different reaction route was observed at 5 °C compared to the other operating temperatures, showing the solid products of ammonium bicarbonates, relatively. The CO₂ removal efficiency and the formation of carbamate and bicarbonate were strongly influenced by the operating temperatures. In particular, the analysis of the formation carbamate and bicarbonate by infrared spectroscopy measurement provides useful information on the reaction mechanism of CO₂ in an aqueous ammonia solution.     

Thermal and neutron shielding properties of <Superscript>10</Superscript>B<Subscript>2</Subscript>O<Subscript>3</Subscript>/polyimide hybrid materials

In this study, ¹⁰B₂O₃/polyimide (PI) hybrid materials were synthesized with the aim to improve their thermal stability and neutron shielding properties. 3,3′-Diaminodiphenyl sulfone (DADPS) reacted with 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) in N-methyl-2-pyrrolidone (NMP) and mixed with amine functionalized ¹⁰B₂O₃ to prepare a series of poly (amic acid), meanwhile, corresponding PIs were obtained via the thermal imidization procedures. The morphologies and structures of the prepared hybrid materials were characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FT-IR). The thermooxidative and flame retardancy properties of the PI films were examined by thermogravimetric analysis (TGA) and limiting oxygen ındex (LOI). The experimental results showed that as the amount of functionalized ¹⁰B₂O₃ was increased, flame retardant properties of the hybrid films were increased. Hybrid materials were also irradiated with thermal neutrons. The neutron shielding properties increasing depends on the amount and the distribution of the ¹⁰B isotope.     

NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript>@SiO<Subscript>2</Subscript> Nanoparticles Stabilized by Porous Silica Shells

Abstract  

NiFe₂O₄ nanoparticles stabilized by porous silica shells (NiFe₂O₄@SiO₂) were prepared using a one-pot synthesis and characterized for their physical and chemical stability in severe environments, representative of those encountered in industrial catalytic reactors. The SiO₂ shell is porous, allowing transport of gases to and from the metal core. The shell also stabilizes NiFe₂O₄ at the nanoparticle surface: NiFe₂O₄@SiO₂ annealed at temperatures through 973 K displays evidence of surface Ni, as verified by H₂ TPD analyses. At 1,173 K, hematite forms at the surface of the metallic cores of the NiFe₂O₄@SiO₂ nanoparticles and surface Ni is no longer observed. Without the silica shell, however, even mild reduction (at 773 K) can draw Fe to the surface and eliminate surface Ni sites.