Drying of Transformer Board

ABSTRACT

The internal insulation in shell type power transforms is usually ensured by the stacking of plates of board impregnated with oil. A board is in equilibrium with the atmosphere at a moisture content varying from seven to eight percent by weight, but, when the insulating function is required, the water content must be lower than 0.5 %. The aim of the present work is the understanding and the modelling of transformer boards drying.

The first part of this work presents experimental studies showing that the drying of transform board follows two regimes :

- a fast regime in the fim period

- a slow regime, up to 99 percent of dryness.

The effect of heating and the influence of the board thickness on the drying rate also studied. In the second part of this paper, we presnt a model capable to represent the observed kinetics of transformer board drying. This model is based on the diffusion of water vapour in the gaseous phases combined with the transfer of water vapor from the fibres to the -us phase. The due of the average global transfer coefficient can be deduced from the slope of the curve 1 f(drying time), where x     

HEAT AND MASS TRANSFER DURING SAPWOOD DRYING ABOVE THE FIBRE SATURATION POINT

Pine sapwood was dried in an air convection kiln at temperatures between 60-80 °C. Temperature and weight measurements were used to calculate the position of the evaporation front beneath the surface. It was assumed that the drying during a first regime is controlled by the heat transfer to the evaporation front until irreducible saturation occurs. Comparisons were made with CT-scanned density pictures of the dry shell formation during initial stages of drying of boards.

The results indicate a receding evaporation front behaviour for sapwood above approximately 40-50% MC when the moisture flux is heat transfer controlled. After that we finally reach a period where bound water diffusion is assumed to control the drying rate.

The heat transfer from the circulating air to the evaporation front controls the migration flux. In many industrial kilns the heating coils therefore have too small heat transfer rates for batches of thin boards and boards with high sapwood content.     

HIGH INTENSITY DRYING

A mathematical model simulating the heat and mass transfer process during high intensity drying of paper and board has been developed. The model is successful in predicting the vapor pressure developments, pressure driven bulk flow of liquid and vapor, and increased drying rates during high-intensity drying, closely matching the experimental determination.

The model predicts substantial amounts of water removal in the liquid form during high-intensity drying being pushed out of the web by pressurized vapor zone. Water removal by pressure flow of liquid could account for as much as one-third of the total water removed.

Similar to drying under conventional conditions, the existence of a dry zone, wet zone and an intermediate zone with accompanying advancing heat pipe has also been shown for drying under high intensity conditions.     

Food Drying and Dewatering

Food drying and dewatering raises a growing interest because of increasing requirements in quality, specially in the production of ingredients and additives for food formulation. Heat and mass transfers, as well as mechanical phenomena and reactions kinetics induced by these transfers must be more and more carefully controlled during drying and storage.

This chapter relates recent advances in

- drying of solids

- spray-drying

- drum-dryine

- superheateded steam drying

- osmotice dehydration

- hot oil immersion drying     

ESTIMATION OF FUNCTIONS IN DRYING EQUATIONS

In drying problem, particularly for drying foodstuff, modelling is very difficult. Many physical effects have to be taken into account for mass transfer ; then mass transfer coefficient varies

In different models unknown functions must be estimated. It is particularly the case in simple models of drying using average values of water content, where the mass transfer varies versus mean water content in falling rate period. On the other hand in the “diffusion model” we have the same problem concerning the diffusion coefficient which must be also estimated

The method we propose in this paper for these two models : simple and “diffusion model” of drying consists from measurements of temperature and water content of the product to search a numerical approach of the unknown function. This method uses optimization techniques on computer and least squares criterion between model values and experimental data

Results are given for the “diffusion model” applied to shelled corn drying to find the diffusion coefficient and for a simple 11107 del applied to plum drying to find the mass transfer coefficient.     

MULTI-STAGE SPRAY DRYING METHOD IN MANUFACTURING HEAVY DUTY DETERGENTS

Collision of droplets; counter-current spray dryer; drying rate; heat transfer; nonphosphated detergent; spray drying

The spray drying method of non-phosphated granular detergents is studied to decrease the amount of agglomerate particles. The formation of agglomerates is mainly influenced by the concentration of droplets in spray cloud and the water content of droplets at the time of collision. The overlaps of different spray clouds should be de- creased.

The drying rate near the nozzle zone is considerably faster than that calculated by Ranz-Marshal's equation. According to these phenomena, “Multi-stage spray drying” is developed, which is characterized by in stalling plural spraying stages in a spray dryer.

Consequently, non-phosphated detergents are manufactured with the same powder properties and productivity as phosphated detergents.     

A DISTRIBUTED PARAMETER APPROACH TO THE DYNAMICS OF ROTARY DRYING PROCESSES

A nonequilibrium distributed parameter model for rotary drying and cooling processes described by a set of partial differitial equations with nonlinear algebraic constraints is developed in this work. These equations arise from the multi-phase heat and mass balances on a typical rotary dryer. A computational algorithm is devekped by employing a polynonial approximation ( orthogonal collocation) with a glotal splinc technique leading to a differential-algebraic equation ( DAE) system. The numerical solution is carried out by using a standard DAE solver.

The two- phase-flow heat transfer coelficient is computed by introducing a correction factor to the commonly accepted correlations. Since interaction between the falling particles are considered in the correction factor,the results are more reliable than those computed by assuming that heat transfer between a single falling particle and the drying air is unaffected by other particles. The heat transfer computations can be further justified via a study on the analogies between heat and mass transfer.

The general model devloped in this work is mathematically more ritorous yet more flexible that the lumped parameter models established by one of the authors (Douglas et al., (1993)). The three major assumptions of an equilibrium operation, perfect mixing and constant drying raic, are removed in the distributed parameter model.

The simulation results are compared with the operational data from an industrial sugar dryer and predictions from earlier models. The model and algorithm successfully predict the steady state behaviour of rotary dryers and collers. The generalized model can be applied to fertilizer drying processes in which the assumption of constant drying rate is no longer valid and the existing dynamic models are not applicable.     

Drying Sawdust in a Pulsed Fluidized Bed

The objective of this work was the experimental and theoretical study of sawdust drying, in batch and continuous experiences, using a pulsed fluidized bed dryer.

In the batch experiences, a 2³ factorial design was used to determine the kinetics of drying, the critical moisture content, and the effective coefficients of both diffusivity and heat transfer, all of them as a function of the velocity and temperature of the air, the speed of turning of the slotted plate that generates the air pulses in the dryer, using sawdust with 65% moisture in each run.

In the continuous operation, a 2³ factorial design was used to study the effect of the solid flow and the velocity and temperature of the air on both the product moisture and the distribution of residence times. In order to determine these last ones, digital image processing was used, utilizing sawdust colored by a solution of methylene blue as tracer.

The statistically significant factors were the velocity and the temperature of the heating air, for both the continuous and batch operations. Although the speed of turn of the slotted plate was not significant, it was observed that the air pulses increased the movement of particles, facilitating its fluidization, especially at the beginning of drying.

The heat transfer coefficients were adjusted according to the equation Nu = 0.0014 Re_p^1.52, whose standard deviation of fit is 0.145.

The period of decreasing rate was adjusted to several diffusivity models, giving the best fit the simplified variable diffusivity model (SVDM). The curve of distribution of residence times was adjusted using the model of tanks in series, with values between 2.6 and 5 tanks.     

EFFECT OF CREEP AND MECHANO-SORPTIVE EFFECT ON STRESS DEVELOPMENT DURING DRYING

Constitutive equations to quantify wood deformation under combined mechanical loading and moisture content change (1] were coupled with the moisture distribution developed during drying to predict stress and strain in 50 by 190-mm Douglas-fir heartwood lumber.

Two combinations of temperature and relative humidity were used to dry the wood. The overall board shrinkage and the immediately released and set strains were measured as a function of time. Those strains were compared with analytic results, which showed good agreement.

The roles that four strain components played in the development of stress-both at board surface and center were compared for different drying conditions. The significance of creep and mechano-sorptive strain in relieving the stress was demonstrated by varying the model parameters.     

DEVELOPMENT AND VALIDATION OF A PROCESS SIMULATOR FOR DRYING SUBBITUMINOUS COAL

Drying subbituminous coal has never been practiced commercially. The commercial dryers built to date have been designed for drying surface moisture in conjunction with upstream coal preparation facilities. This type of drying is mainly controlled by input energy and the basis of the design is an energy balance. In drying inherent moisture from subbituminous coal, the thermal conductivity of the coal and the diffusion of molecular water within coal particles impose limitations on the process conditions. Energy input and solids residence time in the dryer have to be controlled properly for simultaneously balancing the heat and mass transfer within the coal particles. Improper control of either parameter can cause fires and explosions during the key steps of the drying process—drying and cooling

In parallel to the Anaconda coal drying pilot plant program, a cross-flow, fluid-bed coal drying/cooling process simulator was developed for: (1) understanding the drying phenomena on an individual particle basis; (2) analyzing potential risks and safety limits, and (3) designing the Anaconda pilot plant program

The development of the process simulator was based on both first principles and laboratory data and can be divided into two phases:

1 Development of a semi-mechanistic drying model for Powder River Basin subbituminous coal employing an analytical solution of the diffusion equation

2.Formulation of a fluid-bed cross-bed cross-flow dryer/cooler simulator employing simultaneous heat and mass transfer

This model was validated against process variables data taken on a 4 tph pilot plant. An operable range, or process envelope, has been developed through the pilot plant experience and the process simulation study. Based on the model predictions, an uncertainly range was defined in the design recommendations of a pioneer coal drying plant in scale-up.     

HEAT AND MASS TRANSFER IN THE SHORT-TERM CONTACT OF THE MOIST MATERIALS WITH THE HEATING SURFACE

Compounded boundary-valued problem of the diffusion-filtering heat and mass transfer with arbitrary dimensions of the transfer potential vector was raised and solved based on the theory of short-term contact between the moist material and heat-transfer surface.

The boundary lines of the application of the short-term contact models were established.

The solution of the problem allows to select the directions of the intensification of the drying processes with short-term contact of the phases and to calculate various technological characteristics of the drying processes.     

RELATIONSHIP BETWEEN A SOLAR DRYING MODEL OF RED PEPPER AND THE KINETICS OF PURE WATER EVAPORATION (I)

Drying of red pepper under solar radiation was investigated, and a simple model related to water evaporation was developed. Drying experiments at constant laboratory conditions were undertaken where solar radiation was simulated by a 1000 W lamp.

In this first part of the work, water evaporation under radiation is studied and laboratory experiments are presented with two objectives: to verify Penman's model of evaporation under radiation, and to validate the laboratory experiments. Modifying Penman's model of evaporation by introducing two drying conductances as a function of water content, allows the development of a drying model under Eolar radiation.

In the second part of this paper, the model is validated by applying it to red pepper open air solar drying experiments.     

MASS TRANSFER MODELING FOR VIRGINIA TOBACCO CURING

Four mathematical models, describing the moisture transfer during Virginia tobacco curing under varying air-temperature and humidity were tested using experimental data from an industrial dryer.

The model, based on the assumption that the major resistance to moisture transfer is at the air boundary layer and that the driving force is the water activity difference, was found to be the most accurate. The appropriate mass transfer coefficient was determined.

An empirical equation, predicting the equilibrium moisture content of Virginia tobacco as a function of temperature and water activity of the surrounding air, was proposed and experimentally tested.     

TRANSFER PLASMAS DESTROY PCB FLUIDS

High voltage, ac transfer arcs were used as a reaction zone to destroy polychlorinated biphenyls dissolved in transformer fluid. The extremely high temperature of the arc is of sufficient magnitude that it destroys both the PCB's and the oil in which the PCB's are dissolved.

Although fast pyrolysis is the major destructive mechanism, several other features of the process are unique. For example, the transfer arc discharge is submerged. The arc is created beneath the surface of the transformer oil at a water interface. Furthermore, the water phase is part of the electrical circuit; but it also participates in the reaction chemistry of the plasma arc. Water vapor created by the discharge reacts with the carbon and acetylene formed by pyrolysis to produce hydrogen and carbon monoxide. This retards carbon buildup within the system.

The presence of the water phase also provides a convenient adsorption medium for acid gases (HC1) which are formed by pyrolysis of the PCB's, These gases are infinitely more soluble in the water phase than they are in the transformer oil through which they would have to pass to escape the submerged reaction zone. As a result, this new technology provides a convenient small-scale destruction for oils contaminated with PCB     

UNSTEADY, TWO-DIMENSIONAL HEAT AND MASS TRANSFER IN A PACKED BED OF FINE PARTICLES WITH AN ENDOTHERMIC PROCESS

The basic differential equations controlling the temperature and concentration field in a single packed bed of fine particles were derived and solved for the general case in which unsteady, two-dimensional heat and mass transfer lakes place with an endothermic process.

The time-change of particle- and fluid-temperature and concentration of water vapor (humidity) were calculated by a numerical method which assumed that the rate of the endothermic process can be expressed by a first-order rate equation and that the fluid flowing through the bed is of the piston flow type.

The experiments were conducted for the drying of silica-gel and the two-stage dehydration reaction of natural gypsum to demonstrate the applicability of the present theoretical analysis.

It has been found that the calculated results show satisfactory agreement with the measured data within the range of the experimental conditions employed.     

ATMOSPHERIC CONTACT DRYING OF GRANULAR BEDS WETTED WITH A BINARY MIXTURE

When regarding the atmospheric contact drying of granular beds wetted with a liquid mixture, both the drying rate and the selectivity of the process, i.e. the change of moisture composition, are of interest. The batch drying of a free flowing ceramic substance, wetted with a 2-propanol-water mixture, is investigated in a rotary dryer with heated wall and air flow.

The theoretical analysis is based on physical models for heat and mass transfer, moisture migration and particle transport, which are presented in examples.

The experimental and theoretical results show that higher selectivities can be achieved by reducing the particle size because of the lower liquid-phase mass-transfer resistance. An increase of the rotational speed leads to a higher drying rate with slightly decreased selectivity if the particles are sufficiently small, since contact heat transfer is enhanced.     

Sublimation Kinetics during Freeze-Drying of Pharmaceutical Protein Formulation

The influence of total gas pressure and shelf temperature on sublimation kinetics of BSA-based formulation in glass vial as geometrical configuration was determined with a pilot freeze-dryer in standard operating freeze-drying conditions.

The sublimation rate curves showed three different periods with a plateau corresponding to a stationary regime. These kinetics data were mainly dependent on the shelf temperature and slightly influenced by the total gas pressure. Thus, the sublimation process in our conditions was mainly governed by overall heat transfer rate from the plate and from the surroundings to the sublimation front.

Moreover, it proved that the water vapor mass transfer mechanism through the dried layer occurs by molecular diffusion in Knudsen regime.

Finally, these experimental sublimation kinetics data were found in a quite fair agreement with the set up results. They confirm the validation of previous modeling of mean product temperature profiles during the freeze-drying by using the finite element code FEMLAB in real vial geometry (2-D).     

MODEL SELECTI0N IN AIR DRYING OF FOODS

The purpose of this investigation is to compare various drying models with respect to (a) the accuracy in calculating the material moisture content and temperature versus time and (b) the computation time required.

Mechanistic as well as phenomenological heat and mass transfer models are considered. The mechanistic models are formulated by considering different combinations of mechanisms between (1) moisture diffusion in the solid towards its external surface (2) vaporization and convective transfer of the vapor into the air stream (3) convective heat transfer from the air to the solid's surface (4) conductive heat transfer within the solid mass. The phenomenological model incorporates the drying constant while the mechanistic models incorporate the mass diffusivity, the mass transfer coefficient in the air boundary layer, the thermal conductivity, and the heat transfer coefficient in the air boundary layer.

The proposed methodology is applied to experimental data of four vegetables, namely, potato, onion, carrot, and green pepper. The experiments involve three thickness levels, five temperatures, three water activities, and three air velocities. The results obtained concern (a) the standard deviations between experimental and calculated values of material moisture content andtemperature, which, in combination with the computation time, are the necessary information for model selection for a special application, and (b) the model parameter estimates which are necessary to use the selected model.     

EVALUATION OF OVERALL HEAT TRANSFER RATES BETWEEN BUBBLING FLUIDIZED BEDS AND IMMERSED SURFACES

A mechanistic model to evaluate heat transfer rates between the dense phase of gas fluidized beds and immersed surfaces has been recently presented by the authors. This model, denoted Generalized Heterogeneous Model (GHM), is formulated in terms of effective thermal properties for particles and interstitial gas. It has been conceived with the purpose of achieving a generalized formulation accounting simultaneously for conductive, gas convective and radiant effects.

The model was previously tested as regards its capability to predict radiative heat transfer rates in beds at high temperature and gas convective contribution in beds of large particles and high operating pressures.

It is the principal object of this contribution to evaluate the performance of the GHM for a wide range of particle sizes, covering from The purely conductive regime to the gas convection dominant regime.

Also, the main assumptions incorporated in the model are revised and some modifications are introduced, mainly on the basis of the results obtained by Mazza et al. (1997b).