聚乙烯接枝马来酸锌离聚体对PC／PS体系增容作用的研究

本文用ＤＳＣ和ＳＥＭ等方法研究了不同接枝率、不同加入量的聚乙烯接枝马来酸锌（ＰＥｇ－ＭＡＺｎ）离聚体对ＰＣ／ＰＳ体系增容作用的影响。结果表明,在一定范围内ＰＥ－ｇ－ＭＡＺｎ接枝率越大、加入量越多对ＰＣ／ＰＳ体系的增容效果越好。     

PA1010／PP—g—ATBS／PP共混体系的形态与性能

采有向向双螺杆杆挤出机制备了不同组成的ＰＡ１０１０／ＰＰ及ＰＡ１０１０／ＰＰ－ｇ－ＡＴＢＳ／ＰＰ的共混物。采用聚丙烯接枝丙烯酰胺基甲基丙烷磺酸共聚物（ＰＰ－ｇ－ＡＴＢＳ）作为增容剂来研究对ＰＡ１０１０／ＰＰ共混体系形态与力学性能的影响，研究不同增容剂含量对ＰＡ１０１０／ＰＰ共混物的力学性能，形态结构的影响。     

反应型增容剂PS-co-GMA在PA1010/ABS共混体系中的增容作用

以ＰＳ－ｃｏ－ＧＡＭ作为ＰＡ１０１０／ＡＢＳ共混体系的增容剂,探讨了增容剂的含量对共混体系力学性能的影响,同时,利用熔融共混法制备了ＰＡ１０１０／ＡＢＳ－ｇ－ＧＭＡ共混体系,比较了两种增容方式对共混体系力学性能的影响。     

磺化聚苯乙烯离聚体增容PA1010／HIPS体系的结构与性能

用磺化聚苯乙烯离体增容ＰＡ１０１０／ＨＩＰＳ共混体系,通过ＳＥＭ、ＤＭＡ偏光显微镜和冲击试验考究了离体对ＰＡ１０１０／ＨＩＰＳ体系结构与性能的影响,结果表明未中和的磺化聚乙烯具有最明显的增容效果,其加入量不超过ＨＩＰＳ量的２０％时共混物的冲击性能得到了提高。     

PVC／SBR热塑性弹性体的研制

以ＡＢＳ、氯丁橡胶（ＣＲ）、马来酸酐（ＭＡ）接枝ＳＢＲ（ＳＢＲ－ＭＡ）作增容剂对ＰＶＣ／ＳＢＲ的共混比、增容剂、增塑剂用量做了优化选择。同时对动态硫化ＰＶＣ／ＳＢＲ的硫化体系、硫化工艺条件进行了探讨,并比较了动态硫化对共混体性能的影响。结果表明：ＰＶＣ／ＳＢＲ为８０／２０,增容剂ＡＢＳ／ＳＢＲ－ＭＡ为５／５时,选用半有效硫化体系,１６５℃下动态硫化６ｍｉｎ,共混物综合性能最佳     

增容剂对HDPE／AS合金流变和力学性能的影响

研究了增容剂氯化聚乙烯接枝（丙烯腈／苯乙烯）共聚物对ＨＤＰＥ／ＡＳ共混体系加工流变性能和力学性能的影响。增容剂使共混体系的塑化时间减少,且随着增容剂用量的增加,共混体系的平衡扭矩和拉伸强度增大,而断裂伸长率在ＨＤＰＥ／ＡＳ／ＰＥ－Ｃ－ｇ－ＡＳ＝８０／２０／４时出现极大值;螺杆转速的增加使共混体系的平衡扭矩增大。     

LDPE接枝马来酸锌离聚物对PP／PA6共混体系相容性的影响

采用ＳＥＭ和动态粘弹谱研究了不同接枝率的ＬＤＰＥ接枝马来酸锌离聚物（ＬＤＰＥ－ｇ－ＭＡＺｎ）对ＰＰ／ＰＡ６共混体系相容性的影响。ＬＤＰＥ－ｇ－ＭＡＺｎ采用熔融法合成,所制样品接枝率分别为１．５％（质量,下同）、４．５％和５．４％。研究结果表明,ＬＤＰＥ－ｇ－ＭＡＺｎ能有效地改善ＰＰ／ＰＡ６共混物的相容性,其相容性随离聚物接枝率的提高而增强。在ＰＰ（９０）／ＰＡ（１０）体系中,加入离聚物后分散相（ＰＡ６）更均匀、粒子尺寸更小,而且随着离聚物接枝率的提高,ＰＡ６颗粒的粒径就越小,分散越匀;在ＰＰ（５０）／ＰＡ（５０）的体系中,离聚物的加入使两相互相贯穿,在动态粘弹谱上表现出Ｔｇ相互靠近,熔断温度有所提高。     

SPS及其镧离聚物对PS/PBMA共混体系相容性的影响

通过运用溶液成膜共混法制备了系列聚苯乙烯／聚人烯酸丁酯（ＰＳ／ＰＢＭＡ）共混物。借助差示扫描量热法（ＤＳＣ）、傅里叶变换红外光谱（ＦＴＩＲ）、扫描电子显微镜９ＳＥＭ）研究了磺化磺苯乙烯（ＳＰＳ）及其离物对共体系相容性的影响。共混物中ＳＰＳ磺化度越高,ＰＢＭＡ相的下班伦为温度向高温方向移动越明显 。ＳＰＳ镧离聚物（ＳＰＳ１．８－Ｌａ）为增容剂时,ＤＣＳ结果显示共混物２相Ｔｇ靠扰;ＳＥＭ归咎显示２相分     

羧化聚苯乙烯增容PA1010/PS共混体系的形态及相容性研究

采用扫描电镜、动态粘弹谱和偏光显微镜等方法研究了羧化度的摩尔分数为３．２％时羧化聚苯然增容ＰＡ１０１０／ＰＳ共混体系的形态及相容性。结果表明,在ＰＡ１０１０／ＰＳ体系中ＣＰＳ的加入能有效地改善体系的相容性,这表现在加入ＣＰＳ后分散相与基体间的界面变得模糊。     

PET离聚物共混体系的结晶与熔融行为研究

利用ＤＳＣ对聚对苯二甲酸乙二酯（ＰＥＴ）与离聚物Ｓｕｒｌｙｎ和Ａｃｌｙｎ系列组成的共混体系的结晶与熔融行为进行了研究．结果表明，离聚物对ＰＥＴ的低温与高温结晶都有十分明显的促进作用，离聚物Ｎａ盐比离聚物Ｚｎ盐对ＰＥＴ的结晶加速作用显著。共混体系的熔融热焓随离聚物Ｎａ盐含量的增加有所降低，随Ｚｎ盐含量的增加稍有提高，两者的熔点及熔限与熔融热焓的变化规律一致．     

三元反应型增容剂PS-MAH-GMA在PA1010/ABS共混体系中的增容作用

以PS－MAH－GMA作为PA1010／ABS共混体系的增容剂，探讨了增容剂对共混物的力学性能的影响，结果发现：PS－MAH－GMA作为一种反应型增容剂，对于PA1010／ABS共混体系有较好的增容效果，可提高共混体系的力学性能。     

Investigation of phase morphology,thermal behavior,and impact properties of polyamide-1010/polystyrene blends compatibilized by lightly sulfonated polystyrene ionomers

The phase morphology, thermal behavior, and impact properties of polyamide-1010 (PA)/polystyrene (PS) blends compatibilized by sulfonated polystyrene (HSPS) and their zinc salts (ZnSPS) were investigated, using a dynamic mechanical analyzer (DMA), a scanning electron microscope (SEM), a differential scanning calorimetry (DSC), and a pendulum impact tester. It was found that the addition of the ionomer had an improved effect on the phase morphology of the resulting blends, where the HSPS was a more effective compatibilizer than was the ZnSPS due to its low melt viscosity and less self-agglomeration in the PA matrix. DSC results showed that with increasing the ionomer content the amount of the less perfect crystals of PA increased in these blends and, hence, led to a small increase in the crystallinity of the PA phase. The crystallization rate of the PA in the resulting blends was accelerated slightly by the ZnSPS but was decreased by the HSPS, which was probably due to the nucleation effect of ZnSPS for PA but no nucleation of HSPS. The best improvement in the notched impact strength of the blends was achieved with the content of the ionomer up to 20 wt % based on the amount of PS. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 61–69, 1998     

离聚物单体结构对PET非等温熔融结晶过程的影响

利用差示扫描量热仪、扫描电子显微镜、偏光显微镜等方法研究了不同单体结构的乙烯甲基丙烯酸离聚物(Surlyn)、乙烯基丙烯酸离聚物(Aclyn)及苯乙烯基丙烯酸离聚物(SAA)对聚对苯二甲酸乙二酯(PET)非等温熔融结晶过程的影响.结果表明,加入离聚物后PET的结晶速率常数K由0.35提高到1.00～2.37,提高结晶速率的能力为Aclyn>Surlyn>SAA.SAA中苯环的强位阻效应使其自聚集能力下降,Surlyn中羧酸钠基团上的甲基也产生了较大的位阻,降低了其自聚集能力,Aclyn分子链中没有多余基团干扰,其自聚集能力最强.     

离聚体增容PA1010／SBS共混物的研究

采用磺化丁基胶锌盐(ZnSIIR)离聚体作为PA1010/SBS共混物的增容剂,研究了共混体系的结构、形态、相容性及对材料冲击性能的影响。结果表明,ZnSIIR的加入有效改善了SBS在PA1010中的相容性;对PA1010结晶起成核作用,并加快其结晶速率;共混物缺口冲击强度得到提高,且在PA1010/SBS为90/10、ZnSIIR为SBS的10％左右时效果较佳。     

PA／PP—g—MAH／PP共混物的界面和形态研究

用小角X光衍射和偏光显微镜等方法研究了具有相容区的PA101／PP-g-MAH/PP熔融共混物的界面和结晶开态，PA101和PP－g-MAH在熔融共混过程中生成新的基团，在相间存有界面，体系中两相的结晶形态均匀，共混物的拉伸屈服强度随着界面层厚度的增大而提高。     

Non‐isothermal crystallization kinetics of polyamide 1010/montmorillonite nanocomposite

The non‐isothermal crystallization kinetics of pure polyamide 1010 (PA1010) and PA1010/montmorillonite nanocomposite (PA1010/MMT) was investigated by differential scanning calorimetry (DSC) at various cooling rates. The Avrami analysis modified by Jeziorny and a new method developed by Mo can describe the non‐isothermal crystallization process of PA1010 and PA1010/MMT nanocomposite very well. The difference in the value of exponent n between PA1010 and PA1010/MMT nanocomposite suggests that the nano‐size montmorillonite layers act as nucleation agents of PA1010. The values of half‐time of crystallization and crystallization rate coefficient (CRC) show that the crystallization rate of PA1010/MMT nanocomposite is faster than that of PA1010 at a given cooling rate. Polym. Eng. Sci. 44:861–867, 2004. © 2004 Society of Plastics Engineers.     

The control of miscibility of PP/EPDM blends by adding lonomers and applying dynamic vulcanization

The control of miscibility for isotactic polypropylene (PP) and ethylene-propylene-diene terpolymer (EPDM) has been attempted by adding poly(ethylene-comethacrylic acid) (EMA) ionomers and by applying dynamic vulcanization. The rheological properties, crystallization behavior, and morphology of the dynamically vulcanized EPDM/PP/ionomer ternary blends were investigated with a Rheometrics dynamic spectrometer (RDS), a differential scanning calorimeter (DSC), and a scanning electron microscope (SEM). Two kinds of EMA ionomers neutralized with different metal ions (Na⁺ and ZN⁺⁺) were investigated. Blends were prepared on a laboratory internal mixer at 190°C. Blending and curing were performed simultaneously, i.e., EPDM was vulcanized with dicumyl peroxide (DCP) in the presence of PP/ionomer. The composition of PP and EPDM was fixed at 50/50 by wt% and the contents of EMA ionomer were vaired from 5 to 20 parts based on the total amount of PP and EPDM. It was found that the addition of ionomers and the application of the dynamic vulcanization were effective in enhancing the miscibility of PP and EPDM. The structure of the blends was controlled by the following three component phases, i.e., the phase of the dynamially valcanized EPDM, PP, and Zn-neutralized ionomer. The ternary blends showed more miscibility than the PP/EPDM binary blend. This is due to the thermoplastic interpenetrating polymer network (IPN) of the ternary blends. The structure and properties of the ternary blends differed, depending on the types and contents of ionomer, i.e., the ternary blend containing Na-neutralized ionomer did not show a thermoplastic IPN structure clearly, even though the blend was prepared by dynamic vulcanization. The ternary blend containing Zn-neutralized ionomer clearly showed the behavior of a thermoplastic IPN when the contents of ionomer and DCP were 15 parts and 1.0 part, respectively.     

Nonisothermal crystallization kinetics of flame‐sprayed polyamide 1010/nano‐ZrO2 composite coatings

Polyamide1010 (PA1010) and its composite with nanometer‐sized zirconia (PA1010/nano‐ZrO₂) coatings were deposited using a flame spray process. The kinetics of nonisothermal crystallization of PA1010/nano‐ZrO₂ composite coatings was investigated by differential scanning calorimetry (DSC) at various cooling rates. Several different analysis methods were used to describe the process of nonisothermal crystallization. The results showed that the modified Avrami equation and Mo's treatment could describe the nonisothermal crystallization of the composite coatings very well. The nano‐ZrO₂ particles have a remarkable heterogeneous nucleation effect in the PA1010 matrix. The values of halftime and Z_c showed that the crystallization rate increased with increasing cooling rates for both PA1010 and PA1010/nano‐ZrO₂ composite coating, but the crystallization rate of PA1010/nano‐ZrO₂ composite coating was faster than that of PA1010 at given cooling rate. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007