Corrosion behaviour of Lotus-type porous high nitrogen nickel-free stainless steels

Corrosion behaviour of three austenitic Lotus-type porous high nitrogen Ni-free stainless steels exposed to an acidic chloride solution has been investigated by electrochemical tests and weight loss measurements. Polarization resistance indicates that the corrosion rate of Lotus-type porous high nitrogen Ni-free stainless steels is an order of magnitude lower than that of Lotus-type porous 316L stainless steel in acidic environment. The localised corrosion resistance of the investigated high nitrogen Ni-free stainless steels, measured as pitting potential, E_b, also resulted to be higher than that of type 316L stainless steel. The influences of porous structure, surface finish and nitrogen addition on the corrosion behaviour were discussed.     

Effect of Geobacter sulfurreducens on the microbial corrosion of mild steel, ferritic and austenitic stainless steels

The influence of Geobacter sulfurreducens was tested on the anaerobic corrosion of four different steels: mild steel 1145, ferritic steel 403 and austenitic steels 304L and 316L. Within a few hours, the presence of cells induced a free potential (E_oc) ennoblement around +0.3 V on 1145 mild steel, 403 ferritic steel and 304L austenitic steels and slightly less on 316L. The kinetics of E_oc ennoblement depended on the amount of bacteria in the inoculum, but the final potential value depended essentially on the nature of the material. This effect was due to the capacity of G. sulfurreducens to create a direct cathodic reaction on steel surfaces, extracting the electrons directly from material. The presence of bacterial cells modified the corrosion features of mild steel and ferritic steel, so that corrosion attacks were gathered in determined zones of the surface. Local corrosion was significantly enhanced on ferritic steel. Potential ennoblement was not sufficient to induce corrosion on austenitic steels. In contrast G. sulfurreducens delayed the occurrence of pitting on 304L steel because of its capability to oxidize acetate at high potential values. The electrochemical behaviour of 304L steel was not affected by the concentration of soluble electron donor (acetate, 1–10 mM) or the amount of planktonic cells; it was directly linked to the biofilm coverage. After polarization pitting curves had been recorded, microscopic observations showed that pits propagated only in the surface zones where cell settlement was the densest. The study evidenced that Geobacter sulfurreducens can control the electrochemical behaviour of steels in complex ways that can lead to severe corrosion. As Geobacteraceae are ubiquitous species in sediments and soils they should now be considered as possible crucial actors in the microbial corrosion of buried equipment.     

Corrosion and passivation of low-temperature nitrided AISI 304L and 316L stainless steels in acidified sodium sulphate solution

304L and 316L steels were nitrided at 425 °C for 30 h and examined at various depths in 0.1 M Na₂SO₄ acidified to pH 3.0. In the near-surface region with about 7-14 wt% N, at potentials of active state anodic currents were much higher than those for untreated steels, whereas in deeper regions with <7 wt% N the currents were only slightly increased in comparison with untreated steels or they were even lower in passive and transpassive states. Surface films were composed of oxygen-containing species on top and of Cr-N species in deeper layers. It is suggested that strong corrosion of near-surface regions is associated with nitride precipitates. Beneficial effect of low nitrogen concentrations can be due to initially accelerated corrosion which leads to larger amounts of passivating species and to the accumulation of corrosion resistant chromium nitrides.     

Corrosion behaviour of micro-plasma arc welded stainless steels in H3PO4 under flowing conditions at different temperatures

This paper studies the general corrosion behaviour of the micro-plasma arc welded AISI 316L stainless steel in phosphoric acid at different temperatures (25–60 °C) and at a Reynolds number of 1456. Galvanic corrosion has been studied using zero-resistance ammeter (ZRA) measurements and polarization curves (by the mixed potential theory). Results show that the microstructure of the stainless steel is modified due to the micro-plasma arc welding procedure. Coupled current density values obtained from polarization curves increase with temperature. ZRA tests present the highest i_G values at 60 °C; however, the values are very close to zero for all the temperatures studied. This is in agreement with the low value of the compatibility limit and of the parameter which evaluates the importance of the galvanic phenomenon. Both techniques present the most positive potentials at the highest temperature. This study reveals that micro-plasma arc welded AISI 316L stainless steels are appropriated working in the studied H₃PO₄ media from a corrosion point of view for all the temperatures analysed.     

Electrochemical behavior of sintered oxide dispersion strengthened stainless steels

The electrochemical behavior of powder metallurgy (P/M) oxide dispersion strengthened stainless steels (SS) (316L and 434L) have been compared with standard 430 and 316 wrought samples in 0.05 mol/l sulfuric acid. The effects of sintering temperature and yttria addition on the electrochemical behavior have been studied. The behaviour of the dispersion strengthened SS was comparable to that of the straight P/M samples. The straight P/M samples sintered at 1400 °C exhibited better corrosion resistance compared to the samples sintered at 1250 °C and this has been correlated to sintered densities. The P/M austenitic SS were superior to the P/M ferritic SS. Pitting resistance, studied by cyclic polarization experiments in 3.56 wt.% NaCl, of the P/M samples were comparable to the wrought samples. The addition of Y₂O₃ did not affect the pitting resistance.     

Comparative studies on the corrosion properties of a Fe-Mn-Al-Si steel and an interstitial-free steel

Recent developments in a group of super ductile Fe-Mn-Al-Si steels with high-manganese content demands for more research in the corrosion behavior of such steels. The corrosion properties of the Fe-Mn-Al-Si steel was studied in acidic (0.1 M H₂SO₄), alkaline (0.1 M NaOH) and chloride-containing (3.5% NaCl) environments, using immersion and polarization experiments and compared with that of interstitial-free (IF) steel. In acidic solution, the Fe-Mn-Al-Si steel exhibited significantly lower corrosion resistance than that of IF steel. Though the Fe-Mn-Al-Si steel showed lower corrosion resistance as compared to IF steel in chloride solution, the difference was not as substantial as observed in acidic medium. However, in alkaline solution, the Fe-Mn-Al-Si steel showed no significant difference in the corrosion resistance in comparison with that of IF steel, and moreover exhibited substantially high corrosion resistance than in acidic and chloride solution. The post-corrosion characterization studies showed higher corrosion attack of the Fe-Mn-Al-Si steel exposed to acidic solution as compared to that in alkaline and chloride solutions, which is consistent with the corrosion measurement data.     

Aqueous corrosion behaviour of sintered stainless steels manufactured from mixes of gas atomized and water atomized powders

The electrochemical corrosion improvement of a powder metallurgical (PM) stainless steel is studied in this work. Water atomized (WA) ferritic AISI 434L powders have been mixed with gas atomized (GA) austenitic (AISI 316L type) and ferritic (AISI 430L type) powders and processed through the traditional PM route. The addition of GA powder to the usual WA powder decreases the mean size of the pores of the sintered stainless steels. As the bigger pores are the ones that are able to act as crevices, unlike the smaller ones - that act as closed porosity, reduction in the number of big pores tends to improve the corrosion behaviour of PM stainless steels. Reductions of the corrosion rate (i_corr) and increases of the corrosion potential (E_corr) have been measured in neutral media, with and without chlorides. Moreover, the additional beneficial effect of achieving a duplex microstructure through the addition of GA austenitic powders to the WA ferritic powders has also been verified.     

The effect of test temperature on SCC behavior of austenitic stainless steels in boiling saturated magnesium chloride solution

The stress corrosion cracking (SCC) of the austenitic stainless steels of types 304, 310 and 316 was investigated as a function of test temperature in boiling saturated magnesium chloride solution (MgCl₂) using a constant load method. Both of types 304 and 316 exhibited similar corrosion elongation curves, while the corrosion elongation curve of type 310 was different from those of types 304 and 316, in terms of the three parameters such as time to failure (t_f), steady-state elongation rate (l_ss) and transition time to time to failure ratio (t_ss/t_f) obtained from the corrosion elongation curves for these stainless steels. The relationship between the time to failure and a reciprocal of test temperature fell in two straight lines on a semi-logarithmic scale as well as the relationship between the steady-state elongation rate and a reciprocal of test temperature. These regions were considered to correspond to a SCC-dominated region and a hydrogen embrittlement (HE)-dominated region from the value of (t_ss/t_f) and the fracture appearance. The relationship between the steady state elongation rates versus time to failure on a logarithmic scale became a straight line, whereas the slopes of the line for the stainless steels were different with the different fracture mechanism such as SCC and HE. It was found that the linearity of the relationship can be used to predict the time to failure for the stainless steels in the corrosive environment. In addition, type 310 did not suffer from HE, which means that type 310 showed only SCC. This would be explained by whether or not a formation of α′-martensite takes place.     

Microelectrochemical corrosion study of super martensitic welds in chloride-containing media

Pitting corrosion was studied in welded joints of supermartensitic stainless steels. The electrochemical behavior of three different weldment zones (weld metal (WM), parent metal (PM) and heat affected zone (HAZ)) was characterized independently using an electrochemical minicell through potentiodynamic and potentiostatic techniques. The minicell design selected for this work has the additional advantage of showing promise for service application. Macro-electrochemical characterization was also used to provide a basis for comparison and check the effectiveness of minicell techniques in characterizing the corrosion resistance of welded super martensitic stainless steels. Minicell experiments exhibit a great capacity to discriminate between the different welding zones. The electrochemical response can be correlated with the microstructure of the different zones. Thermal cycles resulting from the welding procedure do not have an important effect on the amount of retained austenite or on the values of the pitting potential E_P in the HAZ.     

Effect of ageing heat treatments on the microstructure and intergranular corrosion of powder metallurgy duplex stainless steels

The influence of ageing heat treatments (675 and 875 °C for 1.5 to 48 h) on the microstructure and intergranular corrosion resistance of sintered in nitrogen duplex stainless steels was investigated. The materials were obtained by sintering mixtures of austenitic AISI 316L and ferritic AISI 430L powders. Corrosion behaviour was evaluated by using electrochemical techniques. The beneficial effect of nitrogen on corrosion behaviour of solution annealed samples was established. During ageing, secondary phases were precipitated and the intergranular and transgranular corrosion resistance significantly decreased though repassivation was observed in specimens aged at 875 °C for times up to 8 h.     

Pitting corrosion behaviour of austenitic stainless steels with Cu and Sn additions

The influence of Cu and Sn on the pitting corrosion resistance of AISI 304 and 316 stainless steels in chloride-containing media has been investigated. The corrosion behaviour was evaluated by cyclic polarization, potentiostatic CPT measurements and electrochemical impedance spectroscopy in 3.5 wt% NaCl. The corrosion resistance was also studied in FeCl₃ under Standard ASTM G-48. According to the results, Cu addition favours pit nucleation but inhibits its growth, whereas Sn exerts the opposite effect, favouring pit growth and inhibiting its nucleation. Studies by SEM, X-ray mapping and EDS analysis showed Cu-, Cl- and O-rich corrosion products that reduce the extent of corrosion damage.     

Corrosion behavior of iron-based alloys in the LiBr + ethylene glycol + H2O mixture

The corrosion resistance of 1018 carbon steel, 304 and 316 type stainless steels in the LiBr (55 wt.%) + ethylene glycol + H₂O mixture at 25, 50 and 80 °C has been studied using electrochemical techniques which included potentiodynamic polarization curves, electrochemical noise and electrochemical impedance spectroscopy techniques. Results showed that, at all tested temperature, the three steels exhibited an active-passive behavior. Carbon steel showed the highest corrosion rate, since both the passive and corrosion current density values were between two and four orders of magnitude higher than those found for both stainless steels. Similarly, the most active pitting potential values was for 1018 carbon steel. For 1018 carbon steel, the corrosion process was under a mixed diffusion and charge transfer at 25 °C, whereas at 50 and 80 °C a pure diffusion controlled process could be observed. For 316 type stainless steel, at 25 and 50 °C a species adsorption controlled process was observed, whereas at 80 °C a diffusion controlled mechanism was present. Additionally, at 25 °C, the three steels were more susceptible to uniform type of corrosion, whereas at 50 and 80 °C they were very susceptible to localized type of corrosion.     

Depassivation-repassivation behavior of type-312L stainless steel in NaCl solution investigated by the micro-indentation

Repassivation behavior of type-312L stainless steel containing 6% of molybdenum was examined in NaCl solution using in situ micro-indentation technique, together with type-304 and 316L stainless steels. High stability of the passive film formed on the type-312L stainless steel was also examined by depth profiling analysis of passive films using glow discharge optical emission spectroscopy (GDOES). In 0.9 mol dm⁻³ NaCl solution at 296 K the type-304 and 316L stainless steels are passive only up to 0.3 V (SHE), above which pitting corrosion occurs. In contrast, no pitting corrosion occurs on type-312L stainless steel. Despite the significant difference of the pitting corrosion resistance, the repassivation kinetics of the three stainless steels, examined by micro-indentation at 0.3 V (SHE), is similar. The presence of molybdenum in the stainless steel does not influence the repassivation kinetics. The charge required to repassivate the ruptured type-312L stainless steel surface increases approximately linearly with the potential, even though the passivity-maintaining current increased markedly at potentials close to the transpassive region. Repassivation occurs without accompanying significant dissolution of steel, regardless of the stability of passive state. Depth profiling analyses of the passive films on the type-312L stainless steels formed at several potentials revealed that molybdenum species enrich in the outer layer of the passive film, below which chromium-enriched layer is present. The permeation of chloride ions may be impeded by the outer layer containing molybdate, enhancing the resistance against the localized corrosion of the type-312L stainless steel.     

Corrosion behaviour of duplex stainless steels sintered in nitrogen

Duplex stainless steels obtained through powder metallurgy (PM) technology from austenitic AISI 316L and ferritic AISI 430L powders were mixed on different amounts to obtain biphasic structures with austenite/ferrite ratio of 50/50, 65/35 and 85/15. Prepared mixes of powders have been compacted at 750 MPa and sintered in N₂-H₂ (95% and 5%) at 1250 °C for 1 h. Corrosion behaviour, using electrochemical techniques such as anodic polarization measurement, cyclic anodic polarization scan and electrochemical potentio-kinetic reactivation test and double loop electrochemical potentio-kinetic reactivation double loop test were evaluated. For duplex stainless steels, when austenite/ferrite ratio increases the corrosion potential shifts to more noble potential and passive current density decreases. The beneficial effect of annealing solution heat treatment on corrosion behaviour was established and was compared with corrosion behaviour of vacuum sintered duplex stainless steels. The results were correlated with the microstructural features.     

Oxidation resistance of sintered stainless steels: effect of yttria additions

The porosity of sintered stainless steels modifies their oxidation behavior, as compared to that of wrought stainless steels. This work studies the oxidation behavior of three sintered stainless steels: one ferritic (AISI 434L) and two austenitic (AISI 316L and 304L). 304L with yttria additions is also been studied to explore the possibility of reducing the oxidation rate of austenitic stainless steels by using this reactive element. The results demonstrate the influence of the formation of NiFe₂O₄ on the high-temperature behavior of sintered austenitic stainless steels and the effectiveness of yttria additions in increasing the oxidation resistance at 800 °C.     

Microstructure and pitting corrosion resistance of annealed duplex stainless steel

The transition from metastable to stable pitting was studied in 0.5 M NaCl water solution for two cast duplex stainless steels under different microstructural conditions achieved by annealing in the range from 900 °C to 1200 °C. The ensuing microstructural changes in heat treated steels were defined and correlated with established pitting potentials (E_p) and sites of corrosion damage initiation. The variations in E_p have been discussed in terms of secondary phases precipitation. The critical condition for pit stability was quantified and used to select an appropriate microstructural state, resulting in the higher potential at which stable pit growth is first observed.     

Chromium–palladium films on 316L stainless steel by pulse electrodeposition and their corrosion resistance in hot sulfuric acid solutions

Chromium–palladium alloy films with good adhesive strength and higher micro-hardness have been deposited on 316L stainless steel by pulse electroplating. The films are composed mainly of chromium and palladium crystallites in the metallic state, with grain sizes less than 100 nm. On the film surface Cr(OH)₃ and Cr₂O₃ are present. The co-deposited Cr and Pd in the films show a synergetic effect on passivation. In boiling 20 wt.% H₂SO₄ solution, boiling acetic–formic acid mixture, and simulated PEM fuel cells environment, the Cr–Pd-plated 316L steel shows excellent corrosion resistance.     

Accelerated corrosion of five commercial steels under a ZnCl2-KCl deposit in a reducing environment typical of waste gasification at 673-773 K

The corrosion of five Fe-Cr commercial steels containing 0-18 wt.% Cr at 673-773 K has been studied in a reducing H₂-HCl-CO₂ atmosphere under a ZnCl₂-KCl deposit typical of waste gasification environments. In comparison with the behavior of the same steels in a similar gas mixture without salt deposit, all steels suffered from accelerated corrosion induced by the salt and formed porous scales with poor adherence to the underlying steels. Some Cl was detected close to the steels/scale interface, indicating that Cl-containing species were able to go through the scale down to the metal matrix. Even though the corrosion rates generally decreased with increasing Cr content, the high-Cr stainless steel SS304 was still unable to provide a good corrosion resistance against the ZnCl₂-KCl deposit. The reaction mechanisms are discussed on the basis of thermodynamic considerations and of the “active oxidation” model.     

Effect of Mo and Mn additions on the corrosion behaviour of AISI 304 and 316 stainless steels in H2SO4

The work addresses the influence of Mn and Mo additions on corrosion resistance of AISI 304 and 316 stainless steels in 30 wt.% H₂SO₄ at 25 and 50 °C. Corrosion mechanism was determined by gravimetric tests, DC polarization measurements and electrochemical impedance spectroscopy (EIS). The morphology and nature of the reaction products formed on the material surface were analysed by scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS). Reduction of temperature from 50 to 25 °C drastically decreased the corrosion rate of AISI 304 and 316 stainless steels in sulphuric acid solution. Mn additions did not affect significantly the general corrosion resistance due to its low ability to form insoluble compounds in acid medium. Meanwhile, the formation of molybdenum insoluble oxides enhanced the corrosion performance.     

In vitro electrochemical investigations of advanced stainless steels for applications as orthopaedic implants

Potentiodynamic anodic polarization experiments on advanced stainless steels (SS), such as nitrogenbearing type 316L and 317L SS, were carried out in Hank’s solution (8 g NaCl, 0.14 g CaCl₂, 0.4 g KC1, 0.35 g NaHCO₃, 1 g glucose, 0.1 g NaH₂PO₄, 0.1 g MgCl₂, 0.06 g Na₂HPO₄ 2H₂O, 0.06 g MgSO₄ 7H₂O/1000 mL) in order to assess the pitting and crevice corrosion resistance. The results showed a significant improvement in the pitting and crevice corrosion resistance than the commonly used type 316L stainless steel implant material. The corrosion resistance was higher in austenitic stainless steels containing higher amounts of nitrogen. The pit-protection potential for nitrogen-bearing stainless steels was more noble than the corrosion potential indicating the higher repassivation tendency of actively growing pits in these alloys. The accelerated leaching study conducted for the above alloys showed very little tendency for leaching of metal ions, such as iron, chromium, and nickel, at different impressed potentials. This may be due to the enrichment of nitrogen and molybdenum at the passive film and metal interface, which could have impeded the releasing of metal ions through passive film.