Reactive Hot Pressing of ZrB2–SiC Composites

A ZrB₂–SiC composite was prepared from a mixture of zirconium, silicon, and B₄C via reactive hot pressing. The three-point bending strength was 506 ± 43 MPa, and the fracture toughness was 4.0 MPa·m^1/2. The microstructure of the composite was observed via scanning electron microscopy; the in-situ -formed ZrB₂ and SiC were found in agglomerates with a size that was in the particle-size ranges of the zirconium and silicon starting powders, respectively. A model of the microstructure formation mechanism of the composite was proposed, to explain the features of the phase distributions. It is considered that, in the reactive hot-pressing process, the B and C atoms in B₄C will diffuse into the Zr and Si sites and form ZrB₂ and SiC in situ , respectively. Because the diffusion of Zr and Si atoms is slow, the microstructure (phase distributions) of the obtained composite shows the features of the zirconium and silicon starting powders.     

Thermophysical Properties of ZrB2 and ZrB2–SiC Ceramics

Thermophysical properties were investigated for zirconium diboride (ZrB₂) and ZrB₂–30 vol% silicon carbide (SiC) ceramics. Thermal conductivities were calculated from measured thermal diffusivities, heat capacities, and densities. The thermal conductivity of ZrB₂ increased from 56 W (m K)⁻¹ at room temperature to 67 W (m K)⁻¹ at 1675 K, whereas the thermal conductivity of ZrB₂–SiC decreased from 62 to 56 W (m K)⁻¹ over the same temperature range. Electron and phonon contributions to thermal conductivity were determined using electrical resistivity measurements and were used, along with grain size models, to explain the observed trends. The results are compared with previously reported thermal conductivities for ZrB₂ and ZrB₂–SiC.     

Microstructure and Properties of Spark Plasma-Sintered ZrO2–ZrB2 Nanoceramic Composites

In a recent work, ¹ we have reported the optimization of the spark plasma sintering (SPS) parameters to obtain dense nanostructured 3Y-TZP ceramics. Following this, the present work attempts to answer some specific issues: (a) whether ZrO₂-based composites with ZrB₂ reinforcements can be densified under the optimal SPS conditions for TZP matrix densification (b) whether improved hardness can be obtained in the composites, when 30 vol% ZrB₂ is incorporated and (c) whether the toughness can be tailored by varying the ZrO₂–matrix stabilization as well as retaining finer ZrO₂ grains. In the present contribution, the SPS experiments are carried out at 1200°C for 5 min under vacuum at a heating rate of 600 K/min. The SPS processing route enables retaining of the finer t -ZrO₂ grains (100–300 nm) and the ZrO₂–ZrB₂ composite developed exhibits optimum hardness up to 14 GPa. Careful analysis of the indentation data provides a range of toughness values in the composites (up to 11 MPa·m^1/2), based on Y₂O₃ stabilization in the ZrO₂ matrix. The influence of varying yttria content, t -ZrO₂ transformability, and microstructure on the properties obtained is discussed. In addition to active contribution from the transformation-toughening mechanism, crack deflection by hard second phase brings about appreciable increment in the toughness of the nanocomposites.     

In Situ Synthesis of Ultrafine ZrB2–SiC Composite Powders and the Pressureless Sintering Behaviors

Ultrafine ZrB₂–SiC composite powders have been synthesized in situ using carbothermal reduction reactions via the sol–gel method at 1500°C for 1 h. The powders synthesized had a relatively smaller average crystallite size (<200 nm), a larger specific surface area (∼20 m²/g), and a lower oxygen content (∼1.0 wt %). Composites of ZrB₂+20 wt% SiC were pressureless sintered to ∼96.6% theoretical density at 2250°C for 2 h under an argon atmosphere using B₄C and Mo as sintering aids. Vickers hardness and flexural strength of the sintered ceramic composites were 13.9±0.3 GPa and 294±14 MPa, respectively. The microstructure of the composites revealed that elongated SiC grain dispersed uniformly in the ZrB₂ matrix. Oxidation from 1100° to 1600°C for 30 min showed no decrease in strength below 1400°C but considerable decrease in strength with a rapid weight increment was observed above 1500°C. The formation of a protective borosilicate glassy coating appeared at 1400°C and was gradually destroyed in the form of bubble at higher temperatures.     

Pressureless Sintering of ZrB2–SiC Ceramics

A pressureless sintering process was developed for the densification of zirconium diboride ceramics containing 10–30 vol% silicon carbide particles. Initially, boron carbide was evaluated as a sintering aid. However, the formation of a borosilicate glass led to significant coarsening, which inhibited densification. Based on thermodynamic calculations, a combination of carbon and boron carbide was added, which enabled densification (relative density >98%) by solid-state sintering at temperatures as low as 1950°C. Varying the size of the starting silicon carbide particles allowed the final silicon carbide particle morphology to be controlled from equiaxed to whisker-like. The mechanical properties of sintered ceramics were comparable with hot-pressed materials with Vickers hardness of 22 GPa, elastic modulus of 460 GPa, and fracture toughness of ∼4 MPa·m^1/2. Flexure strength was ∼460 MPa, which is at the low end of the range reported for similar materials, due to the relatively large size (∼13 μm long) of the silicon carbide inclusions.     

Properties of ZrB2–SiC Ceramics by Pressureless Sintering

Pressureless sintering was used to densify ZrB₂–SiC ultra-high temperature ceramics. The physical, mechanical, thermal, electrical, and high temperature properties were investigated. This comprehensive set of properties was measured for ZrB₂ containing 20 vol% SiC in which B₄C and C were used as the sintering aids. The three-point flexural strength was 361±44 MPa and the elastic modulus was 374±25 GPa. The Vickers hardness and fracture toughness were 14.7±0.2 GPa and 4.0±0.5 MPa·m^1/2 respectively. Scanning electron microscopy studies of the microstructure of ZrB₂–SiC showed that SiC particles were distributed homogenously in the ZrB₂ matrix with little residual porosity.     

Thermal and Electric Properties in Hot-Pressed ZrB2–MoSi2–SiC Composites

The thermal and electrical properties of MoSi₂ and/or SiC-containing ZrB₂-based composites and the effects of MoSi₂ and SiC contents were examined in hot-pressed ZrB₂–MoSi₂–SiC composites. The thermal conductivity and electrical conductivity of the ZrB₂–MoSi₂–SiC composites were measured at room temperature by a nanoflash technique and a current–voltage method, respectively. The results indicate that the thermal and electrical conductivities of ZrB₂–MoSi₂–SiC composites are dependent on the amount of MoSi₂ and SiC. The thermal conductivities observed for all of the compositions were more than 75 W·(m·K)⁻¹. A maximum conductivity of 97.55 W·(m·K)⁻¹ was measured for the 20 vol% MoSi₂-30 vol% SiC-containing ZrB₂ composite. On the other hand, the electrical conductivities observed for all of the compositions were in the range from 4.07 × 10–8.11 × 10 Ω⁻¹·cm⁻¹.     

Solution-Based Synthesis of Submicrometer ZrB2 and ZrB2–TaB2

Zirconium diboride and a zirconium diboride/tantalum diboride mixture were synthesized by solution-based processing. Zirconium n -propoxide was refluxed with 2,4-pentanedione to form zirconium diketonate. This compound hydrolyzed in a controllable fashion to form a zirconia precursor. Boria and carbon precursors were formed via solution additions of phenol–formaldehyde and boric acid, respectively. Tantalum oxide precursors were formed similarly as zirconia precursors, in which tantalum ethoxide was used. Solutions were concentrated, dried, pyrolyzed (800°–1100°C, 2 h, flowing argon), and exposed to carbothermal reduction heat treatments (1150°–1800°C, 2 h, flowing argon). Spherical particles of 200–600 nm for pure ZrB₂ and ZrB₂–TaB₂ mixtures were formed.     

Pressureless Sintering of High-Density ZrB2–SiC Ceramic Composites

Ultra-high-temperature ceramic composites of ZrB₂ 20 wt%SiC were pressureless sintered under an argon atmosphere. The starting ZrB₂ powder was synthesized via the sol–gel method with a small crystallite size and a large specific surface area. Dry-pressed compacts using 4 wt% Mo as a sintering aid can be pressureless sintered to ∼97.7% theoretical density at 2250°C for 2 h. Vickers hardness and fracture toughness of the sintered ceramic composites were 14.82±0.25 GPa and 5.39±0.13 MPa·m^1/2, respectively. In addition to the good sinterability of the ZrB₂ powders, X-ray diffraction and scanning electron microscopy results showed that Mo formed a solid solution with ZrB₂, which was believed to be beneficial for the densification process.     

Fabrication and Characterization of an Ultra-High-Temperature Carbon Fiber-Reinforced ZrB2–SiC Matrix Composite

A novel carbon fiber-reinforced ZrB₂–SiC matrix composite was fabricated by heaterless chemical vapor infiltration through infiltration of SiC matrix into a carbon fiber-ZrB₂ powder preform. The C/ZrB₂–SiC composite presented a flexural strength of 148 MPa, a fracture toughness of 5.6 MPa·m^1/2, and a good oxidation and ablation resistance.     

Properties of a Pressureless-Sintered ZrB2–MoSi2 Ceramic Composite

A ZrB₂-based composite was fully densified by pressureless sintering at 1850°C with addition of 20 vol% MoSi₂. The microstructure was very fine, with mean dimensions of ZrB₂ grains around 2.5 μm. The four-point flexural strength in air was in excess of 500 MPa up to 1500°C.     

Thermodynamic Analysis of ZrB2–SiC Oxidation: Formation of a SiC-Depleted Region

A thermodynamic model was developed to explain the formation of a SiC-depleted layer during ZrB₂–SiC oxidation in air at 1500°C. The proposed model suggests that a structure consisting of (1) a silica-rich layer, (2) a Zr-rich oxidized layer, and (3) a SiC-depleted zirconium diboride layer is thermodynamically stable. The SiC-depleted layer developed due to active oxidation of SiC. The oxygen partial pressure in the SiC-depleted layer was calculated to lie between 4.0 × 10⁻¹⁴ and 1.8 × 10⁻¹¹ Pa. Even though SiC underwent active oxidation, the overall process was consistent with passive oxidation and the formation of a protective surface layer.     

Effect of the Machining Method on the Catalycity and Emissivity of ZrB2 and ZrB2–HfB2-Based Ceramics

The emissivity and the catalytic efficiency related to atomic oxygen recombination were investigated experimentally in the range 1000–2000 K for ZrB₂ and ZrB₂–HfB₂-based ceramics. In order to evaluate the effect of the machining method, two series of samples, one prepared by electrical discharge machining and the other machined by diamond-loaded tools, were tested. High emissivity (about 0.7 at 1700 K) and low recombination coefficients (on average 0.08 at 1800 K) were found for all the materials. The experimental data showed an effect of the surface machining on the catalytic behavior only on the ZrB₂-based composite; conversely, small variations were found in the recombination coefficients of ZrB₂–HfB₂-based samples for the different machining processes. The surface finish affected the emissivity at lower temperatures in both compositions, with the effect becoming negligible at temperatures above 1500 K.     

Homogeneous Fabrication of Al2O3–ZrO2–SiC Whisker Composite by Surface-Induced Coating

Al₂O₃–ZrO₂–SiC whisker composites were prepared by surface-induced coating of the precursor for the ZrO₂ phase on the kinetically stable colloid particles of Al₂O₃ and SiC whisker. The fabricated composites were characterized by a uniform spatial distribution of ZrO₂ and SiC whisker phases throughout the Al₂O₃ matrix. The fracture toughness values of the Al₂O₃–15 vol% ZrO₂–20 vol% SiC whisker composites (∼12 MPa.m^1/2) are substantially greater than those of comparable Al₂O₃–SiC whisker composites, indicating that both the toughening resulting from the process zone mechanism and that caused by the reinforced SiC whiskers work simultaneously in hot-pressed composites.     

Combustion Synthesis of MoSi2–SiC Composites

MoSi₂, SiC, and MoSi₂–SiC composites were prepared by the thermal explosion mode of self-propagating, high-temperature synthesis (SHS), from elemental powders Mo, Si, and carbon. The products were characterized using chemical analysis, X-ray diffraction, and scanning electron microscopy. The morphology of MoSi₂ in the product points out that it is in the molten state at the combustion temperature. SiC in the composite shows a very fine particle morphology. These results are supported by the earlier thermochemical calculation carried out on this system.     

Combustion Synthesis of Si3N4–SiC Composite Powders

Fine Si₃N₄-SiC composite powders were synthesized in various SiC compositions to 46 vol% by nitriding combustion of silicon and carbon. The powders were composed of α-Si₃N₄, β-Si₃N₄, and β-SiC. The reaction analysis suggested that the SiC formation is assisted by the high reaction heat of Si nitridation. The sintered bodies consisted of uniformly dispersed grains of β-Si₃N₄, β-SiC, and a few Si₂N₂O.     

Fabrication and Characterization of ZrB2-Based Ceramic Using Synthesized ZrB2–LaB6 Powder

ZrB₂–LaB₆ powder was obtained by reactive synthesis using ZrO₂, La₂O₃, B₄C, and carbon powders. Then ZrB₂–20 vol% SiC–10 vol% LaB₆ (ZSL) ceramics were prepared from commercially available SiC and the synthesized ZrB₂–LaB₆ powder via hot pressing at 2000°C. The phase composition, microstructure, and mechanical properties were characterized. Results showed that both LaB₆ and SiC were uniformly distributed in the ZrB₂ matrix. The hardness and bending strength of ZSL were 17.06±0.52 GPa and 505.8±17.9 MPa, respectively. Fracture toughness was 5.7±0.39 MPa·m^1/2, which is significantly higher than that reported for ZrB₂–20 vol% SiC ceramics, due to enhanced crack deflection and crack bridging near SiC particles.     

Oxidation of ZrB2–SiC: Influence of SiC Content on Solid and Liquid Oxide Phase Formation

The effect of SiC concentration on the liquid and solid oxide phases formed during oxidation of ZrB₂–SiC composites is investigated. Oxide-scale features called convection cells are formed from liquid and solid oxide reaction products upon oxidation of the ZrB₂–SiC composites. These convection cells form in the outermost borosilicate oxide film of the oxide scale formed on the ZrB₂–SiC during oxidation at high temperatures (≥1500°C). In this study, three ZrB₂–SiC composites with different amounts of SiC were tested at 1550°C for various durations of time to study the effect of the SiC concentration particularly on the formation of the convection cell features. A calculated ternary phase diagram of a ZrO₂–SiO₂–B₂O₃ (BSZ) system was used for interpretation of the results. The convection cells formed during oxidation were fewer and less uniformly distributed for composites with a higher SiC concentration. This is because the convection cells are formed from ZrO₂ precipitates from a BSZ oxide liquid that forms upon oxidation of the composite at 1550°C. Higher SiC-containing composites will have less dissolved ZrO₂ because they have less B₂O₃, which results in a smaller amount of precipitated ZrO₂ and consequently fewer convection cells.     

Reactive Hot Pressing of ZrB2–SiC–ZrC Composites at 1600°C

A ZrB₂–SiC–ZrC ceramic was produced by reactive hot pressing using Zr, Si, and B₄C as raw materials. The kinetics of the reaction process was studied. The reduction of powders by ball milling is of crucial importance for the sintering. The self-propagating high-temperature synthesis reaction between the raw powders can be ignited by controlling the sintering conditions, which leads to a sintering temperature as low as 1600°C, the lowest sintering temperature reported thus far. The relative density is 97.3%, with an open porosity of 0.6%, and the mechanical properties are comparable to the composites that sintered at higher temperatures. The depletion of oxygen impurities during the sintering was discussed.     

Microstructural Evolution and Grain Growth Kinetics in ZrB2–SiC Composites During Heat Treatment

This work reported the microstructural evolution and grain growth kinetics of ZrB₂–SiC composites containing 10, 20, and 30 vol% SiC during heat treatment at 2000°C. The coarsening of ZrB₂ occurred in the three systems, whereas the obvious coarsening for SiC appeared only in the composite with 30 vol% SiC. The kinetics analysis showed the ZrB₂ grain growth rate in the ZrB₂–30 vol% SiC was 25 times lower than that for ZrB₂–10 vol% SiC during heat treatment. Furthermore, the grain growth controlling mechanisms of ZrB₂ and SiC were discussed. In addition, it was found that the heat treatment had little effect on Vickers hardness and fracture toughness of ZrB₂–SiC.