An Enhanced A-MSDU Frame Aggregation Scheme for 802.11n Wireless Networks

The main goal of the IEEE 802.11n standard is to achieve a minimum throughput of 100 Mbps at the MAC service access point. This high throughput has been achieved via many enhancements in both the physical and MAC layers. A key enhancement at the MAC layer is frame aggregation in which the timing and headers overheads of the legacy MAC are reduced by aggregating multiple frames into a single large frame before being transmitted. Two aggregation schemes have been defined by the 802.11n standard, aggregate MAC service data unit (A-MSDU) and aggregate MAC protocol data unit (A-MPDU). As a consequence of the aggregation, new aggregation headers are introduced and become parts of the transmitted frame. Even though these headers are small compared to the legacy headers they still have a negative impact on the network performance, especially when aggregating frames of small payload. Moreover, the A-MSDU is highly influenced by the channel condition due mainly to lack of subframes sequence control and retransmission. In this paper, we have proposed an aggregation scheme (mA-MSDU) that reduces the aggregation headers and implements a retransmission control over the individual subframes at the MSDU level. The analysis and simulations results show the significance of the proposed scheme, specifically for applications that have a small frame size such as VoIP.     

IEEE 802.11n: enhancements for higher throughput in wireless LANs

This article introduces a new standardization effort, IEEE 802.11n, an amendment to IEEE 802.11 standards that is capable of much higher throughputs, with a maximum throughput of at least 100 Mb/s, as measured at the medium access control data services access point. The IEEE 802.11n will provide both physical layer and MAC enhancements. In this article we introduce some PHY proposals and study the fundamental issue of MAC inefficiency. We propose several MAC enhancements via various frame aggregation mechanisms that overcome the theoretical throughput limit and reach higher throughput. We classify frame aggregation mechanisms into many different and orthogonal aspects, such as distributed vs. centrally controlled, ad hoc vs. infrastructure, uplink vs. downlink, single-destination vs. multi-destination, PHY-level vs. MAC-level, single-rate vs. multirate, immediate ACK vs. delayed ACK, and no spacing vs. SIFS spacing.     

基于IEEE 802.11高速无线局域网的速率自适应MAC协议研究

目前的IEEE 802.11标准在物理层提供了对多种发送速率的支持,然而在MAC层却没有规定速率自适应的方法。该文研究了高速IEEE 802.11 无线局域网中的速率自适应方案。首先,提出了EACK协议,EACK使用基本速率发送MAC头,并在ACK帧中携带信道信息,因而能够较快速地响应信道的变化,同时具有少的开销;其次,在EACK基础上,提出了一种恒定发送时间(CEACK)的策略,CEACK能够克服传统IEEE 802.11 DCF MAC协议的理论吞吐量上限,并且具有更好的时间公平性能,能够应用于高速的无线局域网。     

Efficient MAC strategies for the IEEE 802.11n wireless LANs

Current IEEE 802.11 wireless local area network (WLAN) standard products can provide up to 54 Mbps raw transmission rate, while non‐standard WLAN products with 108 Mbps have already appeared in the market, and the next generation WLAN will provide much higher transmission rates. However, the medium access control (MAC) was designed for lower data rates, such as 1–2 Mbps, and it is not an efficient MAC. Furthermore, a theoretical throughput limit exists due to overhead and limitations of physical implementations, and therefore increasing transmission rate cannot help a lot. Designing efficient MAC strategies becomes critical and important. In this paper, we introduce and propose a series of efficient MAC strategies to overcome the fundamental overhead, and to improve performance. The protocols and mechanisms include Direct Link Protocol, Without Acknowledgement, Without Retransmissions, Block Acknowledgement Protocol, Concatenation, Packing, Multiple Frame Transmission (versions 1 and 2) and Piggyback. The aim of this paper is to introduce and propose these efficient new MACs not only for current IEEE 802.11 standards (.11a/.11b/.11g), but also for the next generation WLAN with higher speed and higher throughput, especially for IEEE 802.11n. Copyright © 2006 John Wiley & Sons, Ltd.     

IEEE 802.11 medium access control enhancements based on simultaneous multiple‐input multiple‐output bandwidth sharing

The demand for higher data rate has spurred the adoption of multiple‐input multiple‐output (MIMO) transmission techniques in IEEE 802.11 products. MIMO techniques provide an additional spatial dimension that can significantly increase the channel capacity. A number of multiuser MIMO system have been proposed, where the multiple antenna at the physical layer are employed for multiuser access, allowing multiple users to share the same bandwidth. As these MIMO physical layer technologies further evolve, the usable bandwidth per application increases; hence, the average service time per application decreases. However, in the IEEE 802.11 distributed coordination function‐based systems, a considerable amount of bandwidth is wasted during the medium access and coordination process. Therefore, as the usable bandwidth is enhanced using MIMO technology, the bandwidth wastage of medium access and coordination becomes a significant performance bottleneck. Hence, there is a fundamental need for bandwidth sharing schemes at the medium access control (MAC) layer where multiple connections can concurrently use the increased bandwidth provided by the physical layer MIMO technologies. In this paper, we propose the MIMO‐aware rate splitting (MRS) MAC protocol and examine its behavior under different scenarios. MRS is a distributed MAC protocol where nodes locally cooperate with one another to share bandwidth via splitting the spatial channels of MIMO systems. Simulation results of MRS protocol are obtained and compared with those of IEEE 802.11n protocol. We show that our proposed MRS scheme can significantly outperform the IEEE 802.11n in medium access delay and throughput. Copyright © 2012 John Wiley & Sons, Ltd.     

Towards providing optimal energy‐efficiency and throughput for IEEE 802.11 WLANs

IEEE 802.11 wireless network standard has become one of the most used wireless networking technologies for smart devices as it offers mobility support and low cost deployment. However, these devices deeply rely on the energy provided by their batteries, which results in limited running time. IEEE 802.11 network standard provides stations with carrier sense multiple access with collision avoidance for the medium access. Yet it results in stations to consume an important amount of power. Therefore, minimizing WiFi‐based energy consumption in smart devices has been received substantial attention in both academia and industry. Accordingly, this paper * proposes a novel beacon‐based energy‐efficient collision‐free medium access control protocol for any type of IEEE 802.11 stations, regardless of being stationary or mobile, or having different amount of traffic flow, transmission rates, or traffic types. The proposed scheme is valid for all types of low or wide bandwidth, single or multiuser multiple‐input multiple‐output WLAN channels, such as IEEE 802.11a\b\g\n\ac. In the proposed scheme, energy saving is achieved, enabling stations to transmit on the right time and maintaining stations in the doze state during a predetermined sleep_time interval after each successful frame transmission, by making use of modified control and management frames of the standard IEEE 802.11 protocol. The proposed scheme reduces the probability of collisions and may allow stations to enter the collision‐free state, regardless of the number of stations on the channel and their traffic types. Widespread simulations have been executed to validate the efficiency of the proposed method. The results demonstrate that the proposed method significantly increases overall throughput and reduces power consumption of stations over IEEE 802.11 WLANs.     

A novel IEEE 802.11‐based MAC protocol supporting cooperative communications

Cooperative diversity is a transmission technique, where multiple terminals form a virtual antenna array that realizes spatial diversity gain in a distributed fashion. The concept of cooperation has already been introduced to MAC layer to design MAC protocol. But it does not take advantage of physical layer's cooperation. In this paper, we present a novel MAC protocol based on IEEE 802.11, called C‐MAC, which is able to support the basic building block of cooperative system. In other words, in C‐MAC, a source would invite a relay node into data transmission if there exits an available one. During data transmission, the source sends the signal to destination in the first time slot. The relay node will retransmit the overheard information to the destination in the second time slot. The destination combines two signals from the source and the helper to create the spatial diversity and robustness against channel fading. The C‐MAC is backward compatible to the legacy IEEE 802.11 system. The performance of C‐MAC mainly depends on physical layer's performance as it just provides the support for cooperation at the MAC layer. If the physical layer works well, C‐MAC would outperform IEEE 802.11 when considering packet error rate (PER). We also perform extensive simulation using ns‐2 with assumptive physical parameters. The results show that C‐MAC would outperform 802.11 if PER is over some threshold, e.g. when PER is 0.4, C‐MAC can achieve up to 11.5% higher throughput than IEEE 802.11. Copyright © 2011 John Wiley & Sons, Ltd.     

Channel Estimation Scheme for WLAN Systems with Backward Compatibility

IEEE 802.11n standards introduced a mixed‐mode format frame structure to achieve higher throughput with multiple antennas while providing backward compatibility with legacy systems. Although multi‐input multi‐output channel estimation was possible only with high‐throughput long training fields (HT‐LTFs), the proposed scheme utilizes a legacy LTF as well as HT‐LTFs in a decision feedback manner to improve the accuracy of the estimates. It was verified through theoretical analysis and simulations that the proposed scheme effectively enhances the mean square error performance.     

POWMAC: a single-channel power-control protocol for throughput enhancement in wireless ad hoc networks

Transmission power control (TPC) has great potential to increase the throughput of a mobile ad hoc network (MANET). Existing TPC schemes achieve this goal by using additional hardware (e.g., multiple transceivers), by compromising the collision avoidance property of the channel access scheme, by making impractical assumptions on the operation of the medium access control (MAC) protocol, or by overlooking the protection of link-layer acknowledgment packets. In this paper, we present a novel power controlled MAC protocol called POWMAC, which enjoys the same single-channel, single-transceiver design of the IEEE 802.11 ad hoc MAC protocol but which achieves a significant throughput improvement over the 802.11 protocol. Instead of alternating between the transmission of control (RTS/CTS) and data packets, as done in the 802.11 scheme, POWMAC uses an access window (AW) to allow for a series of request-to-send/clear-to-send (RTS/CTS) exchanges to take place before several concurrent data packet transmissions can commence. The length of the AW is dynamically adjusted based on localized information to allow for multiple interference-limited concurrent transmissions to take place in the same vicinity of a receiving terminal. Collision avoidance information is inserted into the CTS packet and is used to bound/ the transmission power of potentially interfering terminals in the vicinity of the receiver, rather than silencing such terminals. Simulation results are used to demonstrate the significant throughput and energy gains that can be obtained under the POWMAC protocol.     

一种新的增加Ad hoc网络吞吐量的MAC协议设计

该文提出一种新的MAC协议,其目的是增加802.11b的网络容量。虽然IEEE的802.11b协议提供了较高的原始速率,但是物理层和MAC层随速率提高而引入的额外开销也不断增大。此外,物理层规范定义了两种物理层数据单元格式,但是研究者没有研究如何利用开销小的物理层数据单元来提高802.11b的容量。该文提出一种物理层自适应的算法,它能自适应地选择802.11b物理层规范中的两种不同物理层数据单元格式进行传输,并计算相应的网络分配向量。通过NS仿真证明,该协议能够提高网络的性能,如端到端的时延,有效吞吐量和传包率,特别是在高负载,高速率情况下。     

Parallel relay‐assisted three‐phase MIMO space division multiple access transmission for multi‐hop throughput improvement

Multi‐hop communications equipped with parallel relay nodes is an emerging network scenario visible in environments with high node density. Conventional interference‐free medium access control (MAC) has little capability in utilizing such parallel relays because it essentially prohibits the existence of co‐channel interference and limits the feasibility of concurrent communications. This paper aims at presenting a cooperative multi‐input multi‐output (MIMO) space division multiple access (SDMA) design that uses each hop's parallel relay nodes to improve multi‐hop throughput performance. Specifically, we use MIMO and SDMA to enable concurrent transmissions (from multiple Tx nodes to single/multiple Rx nodes) and suppress simultaneous links' co‐channel interference. As a joint physical layer (MAC/PHY) solution, our design has multiple MAC modules including load balancing that uniformly splits traffic packets at parallel relay nodes and multi‐hop scheduling taking co‐channel interference into consideration. Meanwhile, our PHY layer modules include distributive channel sounding that exchanges channel information in a decentralized manner and link adaptation module estimating instantaneous link rate per time frame. Simulation results validate that compared with interference‐free MAC or existing Mitigating Interference using Multiple Antennas (MIMA‐MAC), our proposed design can improve end‐to‐end throughput by around 30% to 50%. In addition, we further discuss its application on extended multi‐hop topology. Copyright © 2012 John Wiley & Sons, Ltd.     

Aggregation With Fragment Retransmission for Very High-Speed WLANs

In upcoming very high-speed wireless LANs (WLANs), the physical (PHY) layer rate may reach 600 Mbps. To achieve high efficiency at the medium access control (MAC) layer, we identify fundamental properties that must be satisfied by any CSMA-/CA-based MAC layers and develop a novel scheme called aggregation with fragment retransmission (AFR) that exhibits these properties. In the AFR scheme, multiple packets are aggregated into and transmitted in a single large frame. If errors happen during the transmission, only the corrupted fragments of the large frame are retransmitted. An analytic model is developed to evaluate the throughput and delay performance of AFR over noisy channels and to compare AFR with similar schemes in the literature. Optimal frame and fragment sizes are calculated using this model. Transmission delays are minimized by using a zero-waiting mechanism where frames are transmitted immediately once the MAC wins a transmission opportunity. We prove that zero-waiting can achieve maximum throughput. As a complement to the theoretical analysis, we investigate the impact of AFR on the performance of realistic application traffic with diverse requirements by simulations. We have implemented the AFR scheme in the NS-2 simulator and present detailed results for TCP, VoIP, and HDTV traffic. The AFR scheme described was developed as part of the IEEE 802.11n working group work. The analysis presented here is general enough to be extended to proposed schemes in the upcoming 802.11n standard. Trends indicated in this paper should extend to any well-designed aggregation schemes.     

Saturation throughput analysis of multi‐rate IEEE 802.11 wireless networks

IEEE 802.11 protocol supports adaptive rate mechanism, which selects the transmission rate according to the condition of the wireless channel, to enhance the system performance. Thus, research of multi‐rate IEEE 802.11 medium access control (MAC) performance has become one of the hot research topics. In this paper, we study the performance of multi‐rate IEEE 802.11 MAC over a Gaussian channel. An accurate analytical model is presented to compute the system saturation throughput. We validate our model in both single‐rate and multi‐rate networks through various simulations. The results show that our model is accurate and channel error has a significant impact on system performance. In addition, our numerical results show that the performance of single‐rate IEEE 802.11 DCF with basic access method is better than that with RTS/CTS mechanism in a high‐rate and high‐load network and vice versa. In a multi‐rate network, the performance of IEEE 802.11 DCF with RTS/CTS mechanism is better than that with basic access method in a congested and error‐prone wireless environment. Copyright © 2008 John Wiley & Sons, Ltd.     

Arbitration Interframe Space‐controlled Medium Access Control: a medium access control protocol guaranteeing absolute priority in wireless local area networks

The demand for multimedia services, such as voice over Internet Protocol, video on demand, information dissemination, and ?le sharing, is increasing explosively in wireless local area networks. These multimedia services require a certain level of QoS. Thus, it is important to provide QoS for multimedia applications. IEEE 802.11e tries to meet the QoS requirement of multimedia services by using Enhanced Distributed Channel Access. This gives more weights to high‐priority tra?c than low‐priority tra?c in accessing the wireless channel. However, Enhanced Distributed Channel Access suffers from many problems such as low aggregate throughput, high collision rates, and ineffective QoS differentiation among priority classes. In this paper, we propose a new medium access scheme, the Arbitration Interframe Space‐controlled Medium Access Control (AC‐MAC), that guarantees absolute priority in 802.11 wireless networks. In AC‐MAC, the AIFS and contention window values are controlled, so that a higher‐priority tra?c can preferentially access and effectively utilize the channel. Extensive simulations show that AC‐MAC can perfectly provide absolute priority and good throughput performance regardless of the number of contending nodes. In the simulation of voice over Internet Protocol service, AC‐MAC provides effective QoS differentiation among services and also meets the high level of QoS requirements. AC‐MAC also adapts quickly in a dynamic environment and provides good fairness among the nodes belonging to the same priority class. Copyright © 2011 John Wiley & Sons, Ltd.     

Design of an enhanced access point to optimize TCP performance in Wi-Fi hotspot networks

In the last years, the number of Wi-Fi hotspots at public venues has undergone a substantial growth, promoting the WLAN technologies as the ubiquitous solution to provide high-speed wireless connectivity in public areas. However, the adoption of a random access CSMA-based paradigm for the 802.11 MAC protocol makes difficult to ensure high throughput and a fair allocation of radio resources in 802.11-based WLANs. In this paper we evaluate extensively via simulations the interaction between the flow control mechanisms implemented at the TCP layer and the contention avoidance techniques used at the 802.11 MAC layer. We conducted our study considering initially M wireless stations performing downloads from the Internet. From our results, we observed that the TCP downlink throughput is not limited by the collision events, but by the inability of the MAC protocol to assign a higher chance of accessing the channel to the base station. We propose a simple and easy to implement modification of the base station’s behavior with the purpose of increasing the TCP throughput reducing useless MAC protocol overheads. With our scheme, the base station is allowed to transmit periodically bursts of data frames towards the mobile hosts. We design a resource allocation protocol aimed at maximizing the success probability of the uplink transmissions by dynamically adapting the burst length to the collision probability estimated by the base station. By its design, our scheme is also beneficial to achieve a fairer allocation of the channel bandwidth among the downlink and uplink flows, and among TCP and UDP flows. Simulation results confirm both the improvement in the TCP downlink throughput and the reduction of system unfairness.     

Throughput-oriented MAC for mobile ad hoc networks: A game-theoretic approach

The conservative nature of the 802.11 channel access scheme has instigated extensive research whose goal is to improve the spatial reuse and/or energy consumption of a mobile ad hoc network. Transmission power control (TPC) was shown to be effective in achieving this goal. Despite their demonstrated performance gains, previously proposed power-controlled channel access protocols often incur extra hardware cost (e.g., require multiple transceivers). Furthermore, they do not fully exploit the potential of power control due to the heuristic nature of power allocation. In this paper, we propose a distributed, single-channel MAC protocol (GMAC) that is inspired by game theory. In GMAC, each transmitter computes a utility function that maximizes the link’s achievable throughput. The utility function includes a pricing factor that accounts for energy consumption. GMAC allows multiple potential transmitters to contend through an admission phase that enables them to determine the transmission powers that achieve the Nash equilibrium (NE). Simulation results indicate that GMAC significantly improves the network throughput over the 802.11 scheme and over another single-channel power-controlled MAC protocol (POWMAC). These gains are achieved at no extra energy cost. Our results also indicate that GMAC performs best under high node densities and large data packet sizes.     

一种新的基于跨层的Ad Hoc网络的MAC协议设计

为了提高Ad Hoc网络的性能,提出一种新的基于跨层的MAC协议,它能自适应的选择802.11b物理层规范中的两种不同的物理层数据单元格式进行传输。由于具有短导频的物理层数据单元格式比具有长导频的物理层数据格式占用更少的信道时间,基于跨层的MAC协议在一定条件下,采用具有短导频的物理层数据单元进行传输以减少物理层的开销,提高网络性能。其基本思想是如果需要通信的两个节点都支持具有短导频的物理层数据格式,则采用具有短导频的物理层数据格式进行传输,否则,采用具有长导频的物理层数据格式进行传输。同时提出一种自适应的网络分配向量计算算法,该算法能够根据MAC数据包的持续时间值判断节点是否支持具有短导频的物理层数据格式,不需要修改802.11b的帧格式。通过NS仿真证明,基于跨层的MAC协议能够提高网络的性能,如端到端的时延、吞吐量和传包率。     

基于IEEE 802.11g的光载无线网络媒体接入控制协议性能分析

This paper investigates the Medium Access Control (MAC) protocol performance in the IEEE 802.11g-over-fiber network for different payloads and fiber lengths using Direct Sequence Spread Spectrum-Orthogonal Frequency Division Multiplexing (DSSS- OFDM) and Extended Rate Physicals- Orthogonal Frequency Division Multiplexing (ERP-OFDM) physical layers using basic ac-cess mode, Request to Send/Clear to Send (RTS/CTS) and CTS-to-self mechanisms. The results show that IEEE 802.11g-over-fiber network employing the ERP-OFDM physical layer is much more efficient than that em-ploying the DSSS-OFDM physical layer, with regards to both throughput and delay. For a given maximum throughput/minimum delay, the tradeoff among the access mechanism, the fiber length, and the payload size must be considered. Our quantified results give a se-lection basis for the operators to quickly select suitable IEEE 802.11g physical layers and the different access mechanisms, and accurately predict the data throughput and delay given the specific parameters.     

The evolution of 5GHz WLAN toward higher throughputs

A standardization effort has started within the IEEE 802.11 working group to define the next generation of 802.11 wireless LANs. This article illustrates how throughput achieved above the MAC layer of 5 GHz WLANs can be increased from an existing 30 Mb/s maximum with 802.11a/g to rates exceeding 90 Mb/s. After a brief review of ongoing WLAN standardization activities, the support of a higher physical-layer bit rate by various standardized MAC protocols (802.11, 802.11e, and HIPERLAN/2) is discussed, showing the PHY and MAC layers must be considered jointly in order to achieve a significant throughput increase. Various physical layer techniques are compared in terms of performance and complexity. In particular, simulations show that by relying on MAC layers with good efficiency like 802.11e and HIPERLAN/2, a combination of space-time block coding with a possibility of channel bundling could bring a peak throughput increase from 30 to 90 Mb/s as well as a significant cell range increase.     

Saturation throughput analysis of IEEE 802.11e enhanced distributed coordination function

The IEEE 802.11 Task Group E will soon approve the 802.11e standard for medium access control (MAC) layer quality-of-service (QoS) enhancements to the 802.11 protocol, and it is widely believed that these enhancements will allow 802.11 technology to form the foundation of high-bandwidth vertically integrated networks. At the heart of 802.11e is a modified contention-based access mechanism, named the enhanced distributed coordination function (EDCF). In this paper, we propose and validate an analytical model for the saturation throughput of EDCF. Key to the accuracy of our model is a treatment of the postcollision period, which has been ignored by all previous 802.11 models. With results from the ns-2 simulator, we show that our model can accurately predict throughput over a wide range of scenarios, and thereby demonstrate its usefulness as a predictive tool for use in QoS provision. With context provided by our analytical model, we discuss the primary throughput differentiation mechanisms of EDCF.