Effect of Nanoparticle Surface Treatment on Nonisothermal Crystallization Behavior of Polypropylene/Calcium Carbonate Nanocomposites

Polypropylene (PP)/CaCO₃ nanocomposites were prepared by melt-blending method using a Haake-90 mixer. The CaCO₃ nanoparticles were surface modified with a coupling agent before compounding. A fine dispersion of the modified nanoparticles in the nanocomposites was observed by transmission electron microscopy (TEM). Effects of surface treatment of CaCO₃ nanoparticles on the nonisothermal crystallization behavior and kinetics of PP/CaCO₃ nanocomposites were investigated by differential scanning calorimetry (DSC). Jeziorny and Mo methods were used to describe the nonisothermal crystallization process. It was shown that the crystallization temperature of the nanocomposites increased due to the heterogeneous nucleation of the surface-treated nanoparticles. It was found that the nanoparticles modified with a proper content range of coupling agent could facilitate the nonisothermal crystallization of the nanocomposites under certain conditions (the cooling rate and the relative degree of crystallinity). This may be a potential application for the crystallization controlling of composites in manufacturing. In addition, the activation energy of crystallization for the nanocomposites and the nucleation activity of the nanoparticle were estimated by using Kissinger and Dobreva's methods, respectively. It could be concluded that the surface-treated nanoparticles had a strong nucleating activity, which caused the decrease of the activation energy of the nanocomposites.     

Isothermal crystallization and melting behaviors of nano TiO2‐modified polypropylene/polyamide 6 blends

Titanium dioxide (TiO₂) nanoparticles were functionalized with toluene‐2,4‐diisocyanate and then polypropylene/polyamide 6/(PP/PA6) blends containing functionalized‐TiO₂ were prepared using a twin screw extruder. Isothermal crystallization and melting behavior of the as‐prepared composites were investigated using differential scanning calorimetry and wide‐angle X‐ray diffraction. Isothermal crystallization analysis shows that the TiO₂ nanoparticles have two effects on PP/PA6 blends, i.e., it can favor the improvement of crystallization ability and decrease the crystallization rate of PP/PA6 blends. The improvement of crystallization ability is superior over decreasement of crystallization rate of PA6 chains caused by TiO₂, therefore PA6 in PP/PA6/TiO₂ nanocomposites have higher crystallization rate than that of PA6 in pure PP/PA6 blends, which indicated TiO₂ nanoparticles favored the crystallization of PA6. The TiO₂ nanoparticles show no effects on the equilibrium melting temperature (T) values of PP phase but decreases the T values of PA6 phase. In addition, the TiO₂ nanoparticles did not change the crystalline polymorph of PP/PA6 blends basically; however, favored the formation of β‐PP. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Synthesis and properties of homogeneously dispersed polyamide 6/MWNTs nanocomposites via simultaneous in situ anionic ring‐opening polymerization and compatibilization

Toluene 2, 4‐diisocyanate (TDI) functionalized multiwalled carbon nanotubes (MWNTs‐NCO) were used to prepare monomer casting polyamide 6 (MCPA6)/MWNTs nanocomposites via in situ anionic ring‐opening polymerization (AROP). Isocyanate groups of MWNTs‐NCO could serve as AROP activators of ?‐caprolactam (CL) in the in situ polymerization. Fourier transform infrared (FTIR) showed that a graft copolymer of PA6 and MWNTs was formed in the in situ polymerization. MWNTs‐PA6 covalent bonds of the graft copolymer constituted a strong type of interfacial interaction in the nanocomposites and increased the compatibility of MWNTs and MCPA6 matrix. The nanocomposites were characterized for the morphology, mechanical, crystallization, and thermal properties through field emission transmission electron microscopy (FETEM), tensile testing, differential scanning calorimeter (DSC), and thermogravimetric analysis (TGA). FETEM analysis showed that MWNTs were homogeneously dispersed in MCPA6 matrix. The initial tensile strengths and tensile modulus of the nanocomposite with 1.5 wt % loading of MWNTs were enhanced by about 16 and 13%, respectively, compared with the corresponding values for neat MCPA6. DSC analysis indicated that the crystallization temperature of the nanocomposites was increased by 8°C by adding 1.5 wt % MWNTs compared with pure MCPA6. Besides, it was found that the thermal stability of MCPA6 was improved by the addition of the MWNTs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Location of functionalized-TiO<Subscript>2</Subscript> nanoparticle in an immiscible PP/PA6 blends and its effect on the compatibility of the components

Nanocomposites based on 70/30 (w/w) polypropylene (PP)/polyamide 6 (PA6) immiscible blends and functionalized-TiO₂ nanoparticles were prepared via melt compounding. The influences of TiO₂ on the morphology of nanocomposites were investigated. Scanning electron microscopy results revealed the domain size of the dispersed PA6 phase decreased in presence of functionalized-TiO₂ and the TiO₂ nanoparticles were preferentially located at the PA6 phase and at the interfacial region between PP and PA6, which were ascertained by differential scanning calorimetry. The functionalized-TiO₂ nanoparticles played the compatibilizer for the immiscible PP/PA6 blends, increasing the interaction of the two phases in certain extent. Therefore, a clear compatibiliting effect was induced by the TiO₂ in the immiscible PP/PA6 blends.     

Effect of carbon nanotube on PA6/ECO composites: Morphology development,rheological, and thermal properties

Thermoplastic elastomer (TPE) nanocomposites based on polyamide‐6 (PA6)/poly(epichlorohydrin‐co‐ethylene oxide) (ECO)/multiwall carbon nanotube (MWCNTs) were prepared by melt compounding process. Different weight ratios of ECO (20, 40, and 60 wt %) and two kinds of functionalized and non‐functionalized MWCNTs were employed to fabricate the nanocomposites. The morphological, rheological, and mechanical properties of MWCNTs‐filled PA6/ECO blends were studied. The scanning electron microscopy of PA6/ECO blends showed that the elastomer particles, ECO, are well‐dispersed within the PA6 matrix. The significant improvement in the dispersibility of the carboxylated carbon nanotubes (COOH‐MWCNTs) compared to that of non‐functionalized MWCNTs (non‐MWCNTs) was confirmed by transmission electron microscopy images. The tensile modulus of samples improved with the addition of both types of MWCNTs. However, the effect of COOH‐MWCNTs was much more pronounced in improving mechanical properties of PA6/ECO TPE nanocomposites. Crystallization results demonstrated that the MWCNTs act as a nucleation agent of the crystallization process resulted in increased crystallization temperature (T_c) in nanocomposites. Rheological characterization in the linear viscoelastic region showed that complex viscosity and a non‐terminal storage modulus significantly increased with incorporation of both types of MWCNTs particularly at low frequency region. The increase of rheological properties was more pronounced in the presence of carboxylic (COOH) functional groups, in the other words by addition of COOH‐MWCNTs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45977.     

Nonisothermal melt crystallization kinetics of poly(ethylene terephthalate)/Barite nanocomposites

Poly(ethylene terephthalate) (PET)/Barite nanocomposites were prepared by direct melt compounding. The nonisothermal melt crystallization kinetics of pure PET and PET/Barite nanocomposites, containing unmodified Barite and surface‐modified Barite (SABarite), was investigated by differential scanning calorimetry (DSC) under different cooling rates. With the addition of barite nanoparticles, the crystallization peak became wider and shifted to higher temperature and the crystallization rate increased. Several analysis methods were used to describe the nonisothermal crystallization behavior of pure PET and its nanocomposites. The Jeziorny modification of the Avrami analysis was only valid for describing the early stage of crystallization but was not able to describe the later stage of PET crystallization. Also, the Ozawa method failed to describe the nonisothermal crystallization behavior of PET. A combined Avrami and Ozawa equation, developed by Liu, was used to more accurately model the nonisothermal crystallization kinetics of PET. The crystallization activation energies calculated by Kissinger, Takhor, and Augis‐Bennett models were comparable. The results reveal that the different interfacial interactions between matrix and nanoparticles are responsible for the disparate effect on the crystallization ability of PET. POLYM. COMPOS., 31:1504–1514, 2010. © 2009 Society of Plastics Engineers     

Nonisothermal Crystallization and Melting Behaviors of PP/PA6/TiO2 Nanocomposites

Titanium dioxide nanoparticles were functionalized with toluene-2,4-diisocyanate and then polypropylene/polyamide 6 blends containing functionalized titanium dioxide were prepared using a twin-screw extruder. The nonisothermal crystallization and melting behaviors of the as-prepared nanocomposites were investigated using differential scanning calorimetry. The nonisothermal crystallization differential scanning calorimetry data were analyzed by the modified-Avrami (Jeziorny) and combination of Ozawa and Avrami (Mo) methods. It can be found that the Jeziorny method can be used to describe the main crystallization process, and the Mo method can better deal with nonisothermal crystallization kinetics of the polypropylene and polyamide 6 phase in polypropylene/polyamide 6-based nanocomposites. The nonisothermal crystallization analysis shows that the titanium dioxide nanoparticles have two effects on polypropylene/polyamide 6 blends, i.e., it can favor the improvement of crystallization ability and decrease the crystallization rate of the polypropylene and polyamide 6 phase in polypropylene/polyamide 6-based nanocomposites. For one thing, the functionalized titanium dioxide nanoparticles in the polypropylene/polyamide 6-based nanocomposites act as effective nucleation agents and result in higher crystallization temperature (T₀) than that of the polypropylene and polyamide 6 in pure polypropylene/polyamide 6 blends, which indicated titanium dioxide nanoparticles favor the improvement of crystallization ability of the polypropylene and polyamide 6 phase. For another, the existence of functionalized titanium dioxide nanoparticles hinders the free movement of polymer chains and results in lower crystallinity than that of the polypropylene and polyamide 6 in pure polypropylene/polyamide 6 blends, which indicated titanium dioxide nanoparticles decrease the crystallization rate of the polypropylene and polyamide 6 phase in polypropylene/polyamide 6-based nanocomposites. The nonisothermal crystallization melting behaviors show that there is single or double melting peak, which varies with different cooling rates for the polyamide 6 phase in polypropylene/polyamide 6-based nanocomposites. Multiple melting peak is mainly caused by the different crystalline structure of the polyamide 6 phase, the melting peak I is mainly caused by γ crystal of the polyamide 6 phase, while the melting peak II corresponds to the thermodynamic stability of α crystal. Besides, the recrystallization of the polyamide 6 phase in the heating process, and the effect of the incorporation of the titanium dioxide nanoparticles may have some contributions to the appeared multiple melting peak of the polyamide 6 phase in the polypropylene/polyamide 6-based nanocomposites.     

Nucleation effect of surface treated TiO2 on Poly(trimethylene terephthalate) (PTT) nanocomposites

A study of the nucleation effect of TiO₂ in poly(trimethylene terephthalate)/TiO₂ nanocomposite has been carried out using different theoretical models. The models were applied and developed with the aim to describe and better understand the influence of the TiO₂ dispersion on crystallization characteristics of PTT. The PTT/TiO₂ nanocomposites with untreated and surface‐treated TiO₂ were prepared by the melt mixing method. The nucleation efficiency of the TiO₂ nanoparticles has been analyzed with the use of the Avrami model and Mo's method. It was found that the PTT matrix incorporated with surface‐treated TiO₂ particles has a higher crystallization temperature and melting point than that incorporated with untreated TiO₂ particles. As per the models, unlike untreated TiO₂, surface‐treated TiO₂ particles had a lesser effect on the degree of crystallization of the PTT matrix. The TiO₂ nanoparticles act as a nucleating agent in the PTT matrix thereby reducing t_½ of the crystallization and leading to easier crystallization of the polymer. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Nonisothermal crystallization kinetics and thermomechanical properties of multiwalled carbon nanotube‐reinforced poly(ε‐caprolactone) composites

BACKGROUND: The technological development of poly(ε‐caprolactone) (PCL) is limited by its short useful lifespan, low modulus and high crystallinity. There are a few papers dealing with the crystallization behavior of carbon nanotube‐reinforced PCL composites. However, little work has been done on the crystallization kinetics of melt‐compounded PCL/multiwalled carbon nanotube (MWNT) nanocomposites. In this study, PCL/MWNT nanocomposites were successfully prepared by a simple melt‐compounding method, and their morphology and mechanical properties as well as their crystallization kinetics were studied. RESULTS: The MWNTs were observed to be homogeneously dispersed throughout the PCL matrix. The incorporation of a very small quantity of MWNTs significantly improved the storage modulus and loss modulus of the PCL/MWNT nanocomposites. The nonisothermal crystallization behavior of the PCL/MWNT nanocomposites exhibits strong dependencies of the degree of crystallinity (X_c), peak crystallization temperature (T_p), half‐time of crystallization (t_1/2) and Avrami exponent (n) on the MWNT content and cooling rate. The MWNTs in the PCL/MWNT nanocomposites exhibit a higher nucleation activity. The crystallization activation energy (E_a) calculated with the Kissinger model is higher when a small amount of MWNTs is added, then gradually decreases; all the E_a values are higher than that of pure PCL. CONCLUSION: This paper reports for the first time the preparation of high‐performance biopolymer PCL/MWNT nanocomposites prepared by a simple melt‐compounding method. The results show that the PCL/MWNT nanocomposites can broaden the applications of PCL. Copyright © 2008 Society of Chemical Industry     

Preparation and crystallization of poly(ethylene terephthalate)/SiO2 nanocomposites by in‐situ polymerization

Poly(ethylene terephthalate) (PET)/SiO₂ nanocomposites were prepared by in situ polymerization. The dispersion and crystallization behaviors of PET/SiO₂ nanocomposites were characterized by means of transmission electron microscope (TEM), differential scanning calorimeter (DSC), and polarizing light microscope (PLM). TEM measurements show that SiO₂ nanoparticles were well dispersed in the PET matrix at a size of 10–20 nm. The results of DSC and PLM, such as melt‐crystalline temperature, half‐time of crystallization and crystallization kinetic constant, suggest that SiO₂ nanoparticles exhibited strong nucleating effects. It was found that SiO₂ nanoparticles could effectively promote the nucleation and crystallization of PET, which may be due to reducing the specific surface free energy for nuclei formation during crystallization and consequently increase the crystallization rate. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 655–662, 2006     

Nonisothermal crystallization kinetics of flame‐sprayed polyamide 1010/nano‐ZrO2 composite coatings

Polyamide1010 (PA1010) and its composite with nanometer‐sized zirconia (PA1010/nano‐ZrO₂) coatings were deposited using a flame spray process. The kinetics of nonisothermal crystallization of PA1010/nano‐ZrO₂ composite coatings was investigated by differential scanning calorimetry (DSC) at various cooling rates. Several different analysis methods were used to describe the process of nonisothermal crystallization. The results showed that the modified Avrami equation and Mo's treatment could describe the nonisothermal crystallization of the composite coatings very well. The nano‐ZrO₂ particles have a remarkable heterogeneous nucleation effect in the PA1010 matrix. The values of halftime and Z_c showed that the crystallization rate increased with increasing cooling rates for both PA1010 and PA1010/nano‐ZrO₂ composite coating, but the crystallization rate of PA1010/nano‐ZrO₂ composite coating was faster than that of PA1010 at given cooling rate. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Nonisothermal crystallization behavior and mechanical properties of poly(butylene succinate)/silica nanocomposites

Silica nanoparticles and poly(butylene succinate) (PBS) nanocomposites were prepared by a melt‐blending process. The influence of silica nanoparticles on the nonisothermal crystallization behavior, crystal structure, and mechanical properties of the PBS/silica nanocomposites was investigated. The crystallization peak temperature of the PBS/silica nanocomposites was higher than that of neat PBS at various cooling rates. The half‐time of crystallization decreased with increasing silica loading; this indicated the nucleating role of silica nanoparticles. The nonisothermal crystallization data were analyzed by the Ozawa, Avrami, and Mo methods. The validity of kinetics models on the nonisothermal crystallization process of the PBS/silica nanocomposites is discussed. The approach developed by Mo successfully described the nonisothermal crystallization process of the PBS and its nanocomposites. A study of the nucleation activity revealed that the silica nanoparticles had a good nucleation effect on PBS. The crystallization activation energy calculated by Kissinger's method increased with increasing silica content. The modulus and yield strength were enhanced with the addition of silica nanoparticles into the PBS matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of Dispersion Condition of Calcium Carbonate on the Crystallization and Melting Behavior of Polypropylene/CaCO3 Nanocomposites

Polypropylene/calcium carbonate (PP/CaCO₃) nanocomposites were prepared by melt compounding (C-1) and novel compounding process (C-2), respectively. Scanning electronic microscope (SEM) results illustrated that CaCO₃ nanoparticles were well dispersed at nanoscale in C-2, whereas the nanoparticles were mostly aggregate in C-1. Differential scanning calorimetry (DSC) measurements indicated the onset crystallization temperature was increased by 11.4°C and the supercooling wasdecreased by 13.68°C in C-2. A faster crystallization rate, a higher melting point, and a higher degree of crystallization in C-2 were also detected. Polarization light microscope (PLM) photographs showed the spherulites sizes of C-2 were 60 mm, whereas common spherulites with an average size of about 200 mm were observed in both pure PP and C-1. These phenomena demonstrated that the well-dispersed CaCO₃ nanoparticles could result in heterogeneous nucleation effect on PP even at quite low loading Q2 (1.5% wt.).     

Crystallization behavior of poly(ϵ‐caprolactone)/Tio2 nanocomposites obtained by in situ polymerization

Poly(?‐caprolactone) (PCL)/titanium dioxide (TiO₂) nanocomposites were prepared by in situ polymerization of ?‐caprolactone in the presence of modified‐TiO₂ nanoparticles as initiators. The molecular weight of PCL matrix was dependent on the amount of the TiO₂ fillers. The incorporation of TiO₂ did not significantly affect the crystalline structure of PCL. Moreover, a tendency of the nanoparticles to form aggregates was observed, especially at higher fillers contents. The analysis of the crystallization process showed that the addition of TiO₂ nanoparticles accelerated the crystallization rate of PCL, and the crystallization rates increased by increasing the filler content. The crystallization activation energy dependence on the filler content observed here is probably the consequence of the two competing factors. The tendency of activation energy obtained by nonisothermal crystallization is similar to that of isothermal crystallization. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Nonisothermal crystallization behavior of melt‐intercalated polyethylene‐clay nanocomposites

The influence of nanoclay particles on the nonisothermal crystallization behavior of intercalated polyethylene (PE) prepared by melt‐compounding was investigated. It is observed that the crystallization peak temperature (T_p) of PE/clay nanocomposites is slightly but consistently higher than the neat PE at various cooling rates. The half‐time (t_0.5) for crystallization decreased with increase in clay content, implying the nucleating role of nanoclay particles. The nonisothermal crystallization data are analyzed using the approach of Avrami (Polymer 1971, 12, 150), Ozawa (Polym Eng Sci 1997, 37, 443), and Mo and coworkers (J Res Natl Bur Stand 1956, 57, 217), and the validity of the different kinetic models to the nonisothermal crystallization process of PE/clay nanocomposites is discussed. The approach developed by Mo and coworkers successfully explains the nonisothermal crystallization behavior of PE and PE/clay nanocomposites. The activation energy for nonisothermal crystallization of neat PE and PE/clay nanocomposites is determined using the Kissinger (J Res Natl Bur Stand 1956, 57, 217) method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3809–3818, 2006     

Studies on crystallization behaviors and crystal morphology of polyamide 66/clay nanocomposites

X‐ray diffraction methods, DSC thermal analysis, and polarized light microscopy (PLM) were used to investigate the structural changes of nylon 66/clay nanocomposites. PA 66/clay nanocomposites were prepared by the method of melt intercalation. The results indicate that the addition of the intercalated organo‐montmorillonite (OMMT) can induce generation of the β‐form crystal of PA 66 and substantially affect the arrangement of molecules in the α‐form crystal, although the crystallinity scarcely changes. Also, the DSC results indicate that the addition of OMMT in the PA 66 matrix leads to increases of crystallization temperatures and the full width at half maximum (FWHM) of the exothermic peaks. Moreover, the viscosity factor is the main influence on FWHM of the exothermic peaks of PA 66/clay nanocomposites. The results of nonisothermal crystallization kinetics show that OMMT has the effect of heterogeneous nucleation and leads to the decrease of the size of the spherocrystal. The heterogeneous nucleation effects of OMMTs influence the mechanism of crystallization and the growth mode of PA 66 crystals. PLM photographs verify that the size of spherocrystal is decreased and visually confirm the theory of crystallization kinetics. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 756–763, 2005     

Retracted: Effect of surface‐treated TiO2 on non‐isothermal crystallization behavior of poly trimethylene terephthalate nanocomposites

The study of the non‐isothermal crystallization behavior of poly(trimethylene terephthalate) (PTT)/TiO₂ nanocomposites using untreated and surface‐treated TiO₂ has been carried out with different theoretical models. The PTT/untreated TiO₂ and surface‐treated TiO₂ nanocomposites were prepared employing batch mixing technique with an aim to investigate the influence of the TiO₂ dispersion on the crystallization behavior. The nucleation efficiency of the TiO₂ nanoparticles has been demonstrated with the use of Avrami and Jeziorny models. Test results indicated that the PTT matrix with surface‐treated TiO₂ particles has higher crystallization temperature and melting point than those with untreated PTT/TiO₂ nanocomposites. Unlike untreated TiO₂, surface‐treated TiO₂ particles also showed less effect on the degree of crystallization of the PTT matrix. The TiO₂ nanoparticles act as a nucleating agent in the PTT matrix by reducing the t_½ of the crystallization time, thus making it easy to form crystals. © 2012 Society of Plastics Engineers     

Crystallization and morphology studies of biodegradable poly(ε‐caprolactone)/silica nanocomposites

Biodegradable poly(ε‐caprolactone) (PCL)/silica nanocomposites at various silica loadings were prepared via direct melt compounding method in this work. Scanning electron microscopy observation indicated that when the silica content was < 3 wt%, the nanoparticles dispersed evenly in the PCL matrix and exhibited only aggregates with particle size of less than 100 nm. The results of nonisothermal melt crystallization showed that the crystallization peak temperature was higher in the nanocomposites than in neat PCL; moreover, the overall crystallization rate was faster in the nanocomposites than in neat PCL during isothermal melt crystallization. Both nonisothermal and isothermal melt crystallization studies suggested that the crystallization of PCL was enhanced by the presence of silica and influenced by the silica loading. The effect of silica on the crystallization behavior was twofold: the presence of silica may provide heterogeneous nucleation sites for the PCL crystallization while the aggregates of silica may restrict crystal growth of PCL. However, the crystal structure of PCL remained almost unchanged despite the presence of silica in the nanocomposites. POLYM. COMPOS., 2013. © 2012 Society of Plastics Engineers     

Crystallization and melting behavior of multi‐walled carbon nanotube‐reinforced nylon‐6 composites

The crystallization and melting behavior of neat nylon‐6 (PA6) and multi‐walled carbon nanotubes (MWNTs)/PA6 composites prepared by simple melt‐compounding was comparatively studied. Differential scanning calorimetry (DSC) results show two crystallization exotherms (T_{CC, 1} and T_{CC, 2}) for PA6/MWNTs composites instead of a single exotherm (T_{CC, 1}) for the neat matrix. The formation of the higher‐temperature exotherm T_{CC, 2} is closely related to the addition of MWNTs. X‐ray diffraction (XRD) results indicate that only the α‐phase crystalline structure is formed upon incorporating MWNTs into PA6 matrix, independently of the cooling rate and annealing conditions. These observations are significantly different from those for PA6 matrix, where the increase in cooling rate or decrease in annealing temperature results in the crystal transformation from α‐phase to γ‐phase. The crystallization behavior of PA6/MWNTs composites is also significantly different from those reported in PA6/nanoclay systems, probably due to the difference in nanofiller geometry between one‐dimensional MWNTs and two‐dimensional nanoclay platelets. The nucleation sites provided by carbon nanotubes seem to be favorable to the formation of thermodynamically stable α‐phase crystals of PA6. The dominant α‐phase crystals in PA6/MWNTs composites may play an important role in the remarkable enhancement of mechanical properties. Copyright © 2005 Society of Chemical Industry     

Crystallization behavior of carbon nanotubes‐filled polyamide 1010

The nanocomposites of polyamide1010 (PA1010) filled with carbon nanotubes (CNTs) were prepared by melt mixing techniques. The isothermal melt‐crystallization kinetics and nonisothermal crystallization behavior of CNTs/PA1010 nanocomposites were investigated by differential scanning calorimetry. The peak temperature, melting point, half‐time of crystallization, enthalpy of crystallization, etc. were measured. Two stages of crystallization are observed, including primary crystallization and secondary crystallization. The isothermal crystallization was also described according to Avrami's approach. It has been shown that the addition of CNTs causes a remarkable increase in the overall crystallization rate of PA1010 and affects the mechanism of nucleation and growth of PA1010 crystals. The analysis of kinetic data according to nucleation theories shows that the increment in crystallization rate of CNTs/PA1010 composites results from the decrease in lateral surface free energy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3794–3800, 2006