Effect of fibers treatment on dynamic mechanical and thermal properties of epoxy hybrid composites

Epoxy hybrid composites fabricated by reinforcing 2‐hydroxy ethyl acrylate (2‐HEA) treated oil palm empty fruit bunch (EFB) and jute fibers. It assume that chemical modification of jute and oil palm EFB fibers increased fiber/matrix interfacial bonding and it results in enhanced thermal properties of hybrid composites. Dynamic mechanical and thermal analysis of treated hybrid composites was carried out. Results indicated that chemical modification of oil palm EFB and jute fibers affect the dynamic mechanical and thermal properties of hybrid composites. The storage modulus values of hybrid composites increases with chemical treatment and loss modulus increased with fiber treatment in hybrid composites. Damping factor peak values of treated hybrid composites shifted toward the lower temperature compared to both untreated hybrid composites. Cole–Cole analysis was made to understand the phase behaviour of the hybrid composites. Thermogravimetric analysis indicated an increased in thermal stability of hybrid composite with the incorporation of chemically modified fibers. POLYM. COMPOS., 36:1669–1674, 2015. © 2014 Society of Plastics Engineers     

Palm‐based bio‐composites hybridized with kaolinite

This study described the mechanical and thermal properties of hybrid bio‐composites from oil palm empty fruit bunch (EFB) fibers and kaolinite. The polyurethane (PU) used as matrix is formed by reacting palm kernel oil (PKO)‐based polyester with crude isocyanate. The blending ratio of PU to EFB fibers was fixed at 35 : 65 and kaolinite was added at 0, 5, 10, 15, and 20% (by weight). The occurrence of chemical interactions between the hydroxyl terminals in both fillers and the PU system was determined via FTIR spectroscopy. Hybrid bio‐composites showed improved stiffness, strength, and better water resistance with the addition of kaolinite to an extent. At 15% of kaolinite loading, maximum flexural and impact strengths were observed. The interaction between kaolinite with PU matrix and EFB fibers enhanced the mechanical properties of the bio‐composites, which was justified from the FTIR spectrum. However, over‐packing of kaolinite was observed at 20% kaolinite loading, which ruptured the cellular walls and degraded strength of the bio‐composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of filler‐to‐matrix blending ratio on the mechanical strength of palm‐based biocomposite boards

The effect of the blending ratio of a polyurethane matrix and oil‐palm empty fruit bunch (EFB) fibers on the mechanical properties of biocomposite boards has been studied. The PU matrix and EFB fibers were used at blending ratios of 25:75, 30:70 and 35:65 (by weight). The mechanical property of hardness was studied. The intention of this study was to produce fiberboard from a vegetable oil‐based polyester as the matrix and biomass from the palm oil industry, namely EFB. It was found that the blending ratio with a lower filler loading (35:65) gave higher impact and flexural strengths due to better fiber encapsulation which enhanced the fiber–matrix interfacial adhesion. Copyright © 2005 Society of Chemical Industry     

Effect of Fiber Esterification on Fundamental Properties of Oil Palm Empty Fruit Bunch Fiber/Poly(butylene adipate-co-terephthalate) Biocomposites

A new class of biocomposites based on oil palm empty fruit bunch fiber and poly(butylene adipate-co-terephthalate) (PBAT), which is a biodegradable aliphatic aromatic co-polyester, were prepared using melt blending technique. The composites were prepared at various fiber contents of 10, 20, 30, 40 and 50 wt% and characterized. Chemical treatment of oil palm empty fruit bunch (EFB) fiber was successfully done by grafting succinic anhydride (SAH) onto the EFB fiber surface, and the modified fibers were obtained in two levels of grafting (low and high weight percentage gain, WPG) after 5 and 6 h of grafting. The FTIR characterization showed evidence of successful fiber esterification. The results showed that 40 wt% of fiber loading improved the tensile properties of the biocomposite. The effects of EFB fiber chemical treatments and various organic initiators content on mechanical and thermal properties and water absorption of PBAT/EFB 60/40 wt% biocomposites were also examined. The SAH-g-EFB fiber at low WPG in presence of 1 wt% of dicumyl peroxide (DCP) initiator was found to significantly enhance the tensile and flexural properties as well as water resistance of biocomposite (up to 24%) compared with those of untreated fiber reinforced composites. The thermal behavior of the composites was evaluated from thermogravimetric analysis (TGA)/differential thermogravimetric (DTG) thermograms. It was observed that, the chemical treatment has marginally improved the biocomposites' thermal stability in presence of 1 wt% of dicumyl peroxide at the low WPG level of grafting. The improved fiber-matrix surface enhancement in the chemically treated biocomposite was confirmed by SEM analysis of the tensile fractured specimens.     

Polyurethane composites based on oil palm empty fruit bunches: Effect of isocyanate/hydroxyl ratio and chemical modification of empty fruit bunches with toluene diisocyanate and hexamethylene diisocyanate on mechanical properties

This study focuses on the effect of isocyanate (NCO)/hydroxyl (OH) group ratios and chemical modification of oil palm empty fruit bunches (EFBs) with toluene diisocyanate (TDI) and hexamethylene diisocyanate (HMDI) on the mechanical properties of EFB–polyurethane (PU) composites. The tensile, flexural, and impact properties are affected by the NCO/OH ratios. The tensile strengths, flexural strengths, and toughness increase as the NCO/OH increases; however, the modulus decreases. The reduction in the modulus is attributable to the increased flexibility of the PU linkages. Chemical modification of the EFBs increases the tensile strength, flexural strength, and toughness; however, the modulus is lowered as the percentage of treated EFB is increased. Impact strength results show that the strength increases as the NCO/OH ratio is increased. At NCO/OH ratios of 1.0 and 1.1, the composites with HMDI‐treated fibers exhibit higher impact strength than those with TDI‐treated and untreated fibers, respectively. This may be due to the longer and more flexible chain length of HMDI as compared to TDI, which enables the composites to absorb more energy before failure. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

ACETYLATED PLANT-FIBER-REINFORCED POLYESTER COMPOSITES: A STUDY OF MECHANICAL,HYGROTHERMAL, AND AGING CHARACTERISTICS

The potential of acetylation of plant fibers to improve the properties of composites was studied. The chemical modification of oil palm empty fruit bunch (EFB), coconut fiber (Coir), oil palm frond (OPF), jute, and flax using noncatalyzed acetic anhydride were investigated. Proof of acetylation was indicated by the increase in weight percent gain (WPG). Acetylation at a reaction temperature of 120°C had resulted in the reduction in the tensile properties (stress, modulus, and elongation at break) of EFB and Coir composites. However, at 100°C, the acetylated samples exhibited improved properties. The mechanical properties of acetylated EFB- and Coir-fiber-reinforced polyester composites was evaluated at different fiber loadings. The tensile strength and modulus were improved, but elongation at break was slightly reduced upon acetylation, particularly at high fiber loading. Impact properties were moderately increased for those composites with fiber loadings up to 45%. Acetylation exhibited a low moisture absorption, comparable with glass-fiber composites. Acetylated EFB and Coir composites showed superior retention of tensile and impact properties after aging in water up to 12 months.     

Preparation and characterization of chemically modified Jute–Coir hybrid fiber reinforced epoxy novolac composites

In this study, the effects of fiber surface modification and hybrid fiber composition on the properties of the composites is presented. Jute fibers are cellulose rich (>65%) modified by alkali treatment, while the lignin rich (>40%) coconut coir fibers consist in creating quinones by oxidation with sodium chlorite in the lignin portions of fiber and react them with furfuryl alcohol (FA) to create a coating around the fiber more compatible with the epoxy resins used to prepare polymer composites. The maximum improvement on the properties was achieved for the hybrid composite containing the jute–coir content of 50 : 50. The tensile and flexural strength are recorded as 25 and 63 MPa at modified coir fiber content of 50 vol %, respectively, which are 78% and 61% higher than those obtained for unmodified fiber reinforced composites, i.e., tensile and flexural strength are 14 and 39 MPa, respectively. The reinforcement of the modified fiber was significantly enhanced the thermal stability of the composites. SEM features correlated satisfactorily with the mechanical properties of modified fiber reinforced hybrid composites. SEM analysis and water absorption measurements have confirmed the FA-grafting and shown a better compatibility at the interface between chemically modified fiber bundles and epoxy novolac resin. Hailwood–Horrobin model was used to predict the moisture sorption behavior of the hybrid composite systems. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

The effect of compounding techniques on the mechanical properties of oil palm empty fruit bunch–polypropylene composites

Oil palm empty fruit bunch–polypropylene (EFB–PP) composites were produced by employing 2 types of compounding techniques, that is, an internal mixer and a single-screw extruder. The mechanical and water absorption properties of both types of composites were investigated. Overall, for both types of composites, the incorporation of the EFB into PP matrix has resulted in the improvement in the tensile modulus. However, the tensile strength, elongation at break, and impact strength decreased with increasing filler loading. Poor filler–matrix interaction or compatibility and, also, the size irregularity of the EFB are believed to be responsible for the poor ultimate performance. Composites produced by an internal mixer (IM) have displayed higher tensile strength, tensile modulus, and impact strength than with those produced by extrusion (EX). The better performance has been attributed to the effectiveness of the IM, which produces better compounding and improves the wetting of the filler surface. Incorporation of compatibilizer and coupling agent, that is, Epolene wax (E-43) and 3-Aminopropyl triethoxysilane (3-APE), respectively, have produced composites with improved tensile strength for both EX and IM composites. In addition, both types of treatment have resulted in an increase in tensile modulus of EX composites and impact strength of IM composites. Water absorption tests have revealed that the presence of coupling agents and compatibilizers have affected the amount of water absorbed, especially for the 3-APE-treated EFB–PP composites. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2647–2655, 1998     

Effects of fiber‐surface treatment on the properties of hybrid composites prepared from oil palm empty fruit bunch fibers,glass fibers,and recycled polypropylene

In this article, we report the effects of hybridization and fiber‐surface modification on the properties of hybrid composites prepared from recycled polypropylene (RPP), coupling agents, oil palm empty fruit bunch (EFB), and glass fibers through a twin‐screw extruder and an injection‐molding machine. The surface of the EFB fibers was modified with different concentrations (10–15 wt %) and temperatures (60–90°C) of alkali solutions. The structure and morphology of the fibers were observed with the help of Fourier transform infrared spectroscopy and scanning electron microscopy. Different types of composites were fabricated with untreated, alkali‐treated, and heat‐alkali‐treated fibers. Comparative analysis of the mechanical, structural, morphological, and thermal properties of the composites was carried out to reveal the effects of treatment and hybridization. The analysis results reveal that composites prepared from the alkali‐treated (in the presence of heat) fibers show improved mechanical, thermal, and morphological properties with a remarkably reduced water absorption. Additionally, the crystallinity of RPP also increased with the development of biaxial crystals. The improvement of various properties in relation to the structures and morphologies of the composites is discussed. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43049.     

Modification of oil palm empty fruit bunches with maleic anhydride: The effect on the tensile and dimensional stability properties of empty fruit bunch/polypropylene composites

Oil palm empty fruit bunch (EFB)‐filled polypropylene (PP) composites were produced. The EFB filler was chemically modified with maleic anhydride (MAH). The effects of the filler size and chemical modification of EFBs on the tensile and dimensional stability properties of EFB–PP composites were studied. The composites with MAH‐treated EFBs showed higher tensile strengths than those with untreated EFBs. This was attributed to the enhanced compatibility between the MAH‐treated EFBs and PP matrix, as shown in a scanning electron microscopy study. Fourier transform infrared analysis showed evidence of C?C and C?O bonds from MAH at 1630 and 1730 cm^?1, respectively. The MAH‐treated PP composites showed lower water absorption and thickness swelling than those with untreated EFBs. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 827–835, 2003     

Tensile and Impact Properties of Thermoplastic Natural Rubber Reinforced Short Glass Fiber and Empty Fruit Bunch Hybrid Composites

Thermoplastic natural rubber (TPNR) hybrid composite with short glass fiber (GF) and empty fruit bunch (EFB) fiber were prepared via the melt blending method using an internal mixer type Thermo Haake 600p. The TPNR were prepared from natural rubber (NR), liquid natural rubber (LNR) and polypropylene (PP) thermoplastic, with a ratio of 20:10:70. The hybrid composites were prepared at various ratios of GF/EFB with 20% volume fraction. Premixture was performed before the material was discharged into the machine. The study also focused on the effect of fiber (glass and EFB) treatment using silane and maleic anhydride grafted polypropylene (MAgPP) as a coupling agent. In general, composite that contains 10% EFB/10% glass fiber gave an optimum tensile and impact strength for treated and untreated hybrid composites. Tensile properties increase with addition of a coupling agent because of the existence of adherence as shown in the scanning electron microscopy (SEM) micrograph. Further addition of EFB exceeding 10% reduced the Young's modulus and impact strength. However, the hardness increases with the addition of EFB fiber for the untreated composite and decreases for the treated composite.     

Effect of coupling agent content and water absorption on the mechanical properties of coir‐agave fibers reinforced polyethylene hybrid composites

In this study, high‐density polyethylene/agave‐coir composites with two fiber contents (20 and 30 wt%) and different coir‐agave fiber ratios (1–0, 0.8–0.2, 0.6–0.4, 0.4–0.6, 0.2–0.8, and 0–1) were produced in a two‐step process using twin‐screw extrusion followed by injection molding. The effect of mixing two different natural fibers and the addition of coupling agent on water absorption, mechanical properties, and morphology is reported. The rule of hybrid mixture was used to predict the properties of the composites, showing a good agreement with the experimental data. The results obtained showed that the combination of different fibers produces composites with unique characteristics as coir fibers absorb less water than agave fibers, while at the same time increase more tensile and flexural strengths. On the other hand, agave fibers were found to improve the impact strength of coir composites. Also, the effect of water absorption on the mechanical properties was studied. Finally, the use of a coupling agent had a positive effect on mechanical properties, while lowering water uptake. POLYM. COMPOS., 37:3015–3024, 2016. © 2015 Society of Plastics Engineers     

Natural rubber composites reinforced with sisal/oil palm hybrid fibers: Tensile and cure characteristics

Natural rubber was reinforced with untreated sisal and oil palm fibers chopped to different fiber lengths. The influence of fiber length on the mechanical properties of the hybrid composites was determined. Increasing the fiber length resulted in a decrease in the properties. The effects of concentration on the rubber composites reinforced with sisal/oil palm hybrid fibers were studied. Increasing the concentration of fibers resulted in a reduction in the tensile strength properties and tear strength but an increase in the modulus of the composites. Fiber breakage analysis was evaluated. The vulcanization parameters, processability characteristics, and stress–strain properties of these composites were analyzed. The extent of fiber alignment and the strength of the fiber–rubber interface adhesion were analyzed from the anisotropic swelling measurements. Scanning electron microscopy studies were performed to analyze the fiber/matrix interactions. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2305–2312, 2004     

Effect of maleic anhydride‐grafted polypropylene on polypropylene/recycled acrylonitrile butadiene rubber/empty fruit bunch composite

The effect of maleic anhydride‐grafted polypropylene (PP‐g‐MAH) as a compatibilizer on the properties of polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr)/empty fruit bunch (EFB) composites were studied. The composites were melt mixed using a heated two roll mill at 180°C and a speed of 15 rpm with six different compositions (100/0/10, 80/20/10, 70/30/10, 60/40/10, 50/50/10, 40/60/10 phr). The effects of PP‐g‐MAH on mechanical, morphological and chemical properties of the PP/NBRr/EFB composites were examined. The PP‐g‐MAH compatibilized composites have higher tensile values compare to uncompatibilized composites. Scanning electron microscopy showed better adhesion between EFB and PP/NBRr matrices in the presence of PP‐g‐MAH. Better interaction was formed between EFB and PP/NBRr matrices via C‐O‐C ester bonds as indicated by FTIR analysis. J. VINYL ADDIT. TECHNOL., 24:275–280, 2018. © 2016 Society of Plastics Engineers     

Effect of stacking sequence on mechanical properties of hybrid flax/jute fibers reinforced thermoplastic composites

In this study, the hybrid composites were prepared by stacking jute/PP nonwoven and flax/MAPP woven fabrics in defined sequences. Polypropylene (PP) and maleic anhydride grafted polypropylene (MAPP) were used as matrix materials. Jute and flax fibers were treated with alkali solution in order to improve the interface properties of the resultant composites. The mechanical properties of these hybrid composites were analyzed by means of tensile, flexural, and drop‐weight impact tests. The effect of fabric stacking sequence on the mechanical properties of the composites was investigated. The stacking of nonwovens at the top and in alternate layers has resulted in maximum flexural strength, flexural stiffness, and impact force. It was also shown that hybrid composites have improved tensile, flexural, and impact properties in comparison to neat PP matrix. POLYM. COMPOS., 36:2167–2173, 2015. © 2014 Society of Plastics Engineers     

Effect of epolene E‐43 as a compatibilizer on the mechanical properties of palm fiber–poly(propylene) composites

Composites of palm fibers and poly(propylene) (PP) were compounded in an extruder at 200°C. The composites were subsequently injection molded into standard tensile specimens for mechanical characterization. The fracture morphology of the specimens was analyzed by scanning electron microscopy. It was observed that the composite modulus increased with the increase of fiber content, indicating the existence of adhesion between PP and the much stiffer palm fibers. However, the adhesion was not satisfactory and resulted in a decrease in the composite tensile strength with fiber addition. The compatibilizer Epolene E‐43 was used to minimize this incompatibility between the wood fibers and the PP matrix. The maleated PP additive enhanced the fiber–matrix adhesion, resulting in an improvement in composite performance. Also, small fibers showed better mechanical properties than those of long fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2581–2592, 2004     

Mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

Polypropylene (PP) hybrid composites have been produced by compounding two types of mineral fillers, viz., talc and kaolin with PP copolymer using a twin screw extruder. The PP hybrid composite was injection‐molded into dumbbell specimen for tensile, flexural, and impact properties characterizations. MFI and SEM studies were used to characterize the flow and morphological properties of the PP hybrid composites. The result shows that most of the hybrid composites showed a significant decrease in flow, tensile, flexural, and impact properties compared with the single filler‐filled PP composites. However, a hybridization effect was seen for the PPT20K10 hybrid composites, through the synergistic coalescence of positive characteristics from 20 wt % of talc and 10 wt % of kaolin. This hybrid formulation have given an economically advantageous material with the mechanical properties (tensile, flexural, and impact) comparable to those of the talc‐filled PP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 434–441, 2007     

Effect of silane-based coupling agents and acrylic acid based compatibilizers on mechanical properties of oil palm empty fruit bunch filled high-density polyethylene composites

The mechanical properties of composites consisting of high-density polyethylene (HDPE) and oil palm fibrous wastes—that is, empty fruit bunch (EFB)—have been investigated. Tensile modulus showed an increase, whereas tensile strength, elongation at break, and impact strength decreased with increasing filler loading. The strong tendency of EFB to exist in the form of fiber bundles and the poor filler–matrix interaction is believed to be responsible for the poor strength displayed by the composites. Attempts to improve these properties using two types of coupling agents, that is, 3-aminopropyltrimethoxysilane (3-APM) and 3-aminopropyltriethoxysilane (3-APE) and two types of compatibilizers, poly(propylene–acrylic acid) (PPAA) and poly(propylene–ethylene–acrylic acid), (PPEAA), are described. While almost all chemical treatments increased the stiffness of the composites, limited improvement has been observed in the case of tensile strength. This have been attributed to the presence of fiber bundles that remain intact even after several types of chemical treatment have been carried out. Thus, the role of EFB as reinforcing agent is not fully realized. Scanning electron microscopy (SEM) micrographs revealed that the main energy-absorbing mechanisms contributing towards toughness enhancement is through the fiber bundle pull-out process. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 2189–2203, 1998     

Effect of fiber treatments on mechanical properties of coir or oil palm fiber reinforced polyester composites

The use of plant fibers as a reinforcement in polyester matrices requires the issue of compatibility between the two phases to be addressed. Because plant fibers present hydrophilic surfaces and polyesters are generally hydrophobic, poor fiber–matrix dispersion and wetting of the fibers by the matrix may result. As a consequence, the mechanical properties of the composite are severely reduced. This study considers the effect of fiber treatment by chemical modification of the fibers (acetylation) or the use of silane or titanate coupling agents on the mechanical properties of coir or oil palm reinforced polyester composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1685–1697, 2000     

Evaluation of interactions between compatibilizers and photostabilizers in coir fiber reinforced polypropylene composites

Coir fiber‐reinforced polypropylene composites (PP/CF), compatibilized with maleic anhydride grafted polypropylene (PPMAH) and stabilized with a hindered amine, HALS (Tinuvin^® 791) and UV absorber (Hostavin^® ARO 8), were prepared in a co‐rotating twin‐screw extruder. The effects of additives and their interactions were investigated by analyzing the mechanical properties, in tensile strength, scanning electron microscopy (SEM) and Differential Scanning Calorimetry (DSC). The results indicate that the incorporation of coir, in the presence of the compatibilizer, significantly increases tensile strength, but in the absence of the compatibilizer, the natural fibers act as stress concentrators, allowing a lower tensile strength to the sample. The joint presence of Tinuvin^® and the compatibilizer has a negative effect on tensile strength and on the compatibility of the natural fiber with the matrix. UV absorber does not affect the compatibility of the PP/CF composites. POLYM. ENG. SCI., 57:1179–1185, 2017. © 2017 Society of Plastics Engineers