Tribological behavior of short‐fiber‐reinforced polyimide composites under dry‐sliding and water‐lubricated conditions

Polyimide composites reinforced with short‐cut fibers such as carbon, glass, and quartz fibers were fabricated by the polymerization of monomer reactants process. The mechanical properties of the composites with different fiber contents were evaluated. The friction and wear properties of the polyimide and its composites were investigated under dry‐sliding and water‐lubricated conditions. The results indicated that the short‐carbon‐fiber‐reinforced polyimide composites had better tensile and flexural strengths and improved tribological properties in comparison with glass‐fiber‐ and quartz‐fiber‐reinforced polyimide composites. The incorporation of short carbon fibers into the polyimide contributed to decreases in the friction coefficient and wear rate under both dry and water‐lubricated conditions and especially under water lubrication because of the boundary lubrication effect of water. The polyimide and its composites were characterized by plastic deformation, microcracking, and spalling under both dry and water‐lubricated conditions, which were significantly abated under the water‐lubricated condition. The glass and quartz fibers were easily abraded and broken; the broken fibers transferred to the mating metal surface and increased the surface roughness of mating stainless steel, which led to the wear rate increasing for the glass‐fiber‐ and quartz‐fiber‐reinforced polyimide composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Wood‐fiber‐reinforced poly(lactic acid) composites: Evaluation of the physicomechanical and morphological properties

This article presents the results of a study of the processing and physicomechanical properties of environmentally friendly wood‐fiber‐reinforced poly(lactic acid) composites that were produced with a microcompounding molding system. Wood‐fiber‐reinforced polypropylene composites were also processed under similar conditions and were compared to wood‐fiber‐reinforced poly(lactic acid) composites. The mechanical, thermomechanical, and morphological properties of these composites were studied. In terms of the mechanical properties, the wood‐fiber‐reinforced poly(lactic acid) composites were comparable to conventional polypropylene‐based thermoplastic composites. The mechanical properties of the wood‐fiber‐reinforced poly(lactic acid) composites were significantly higher than those of the virgin resin. The flexural modulus (8.9 GPa) of the wood‐fiber‐reinforced poly(lactic acid) composite (30 wt % fiber) was comparable to that of traditional (i.e., wood‐fiber‐reinforced polypropylene) composites (3.4 GPa). The incorporation of the wood fibers into poly(lactic acid) resulted in a considerable increase in the storage modulus (stiffness) of the resin. The addition of the maleated polypropylene coupling agent improved the mechanical properties of the composites. Microstructure studies using scanning electron microscopy indicated significant interfacial bonding between the matrix and the wood fibers. The specific performance evidenced by the wood‐fiber‐reinforced poly(lactic acid) composites may hint at potential applications in, for example, the automotive and packaging industries. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4856–4869, 2006     

Improvement of interfacial properties of carbon fiber‐reinforced poly(phthalazinone ether ketone) composites by introducing carbon nanotube to the interphase

This article aims to improve interfacial properties of carbon fiber‐reinforced poly(phthalazinone ether ketone) (PPEK) composites by means of preparing carbon nanotube (CNT)/carbon fiber hybrid fiber. XPS was used to characterize the chemical structure of unsized carbon fiber and SEM was used to observe the surface topography of carbon fibers. Specific area measurement, dynamic contact angle, and interfacial shear strength (IFSS) testing were performed to examine the effect of CNT on the interfacial properties of carbon fiber/PPEK composites. By the introduction of CNT to the interphase of carbon fiber‐reinforced PPEK composites, an enhancement of IFSS by 55.52% was achieved. Meanwhile, the interfacial fracture topography was also observed and the reinforcing mechanism was discussed. POLYM. COMPOS., 36:26–33, 2015. © 2014 Society of Plastics Engineers     

Barrier properties for short‐fiber‐reinforced epoxy foams

The barrier properties of short‐fiber‐reinforced epoxy foam are characterized and compared with unreinforced epoxy foam in terms of moisture absorption, flammability properties, and impact properties. Compression and shear properties are also included to place in perspective the mechanical behavior of these materials. Compared with conventional epoxy foam, foam reinforced with aramid fibers exhibits higher moisture absorption and lower diffusion, while glass‐fiber‐reinforced foam is significantly stiffer and stronger. In addition, the polymeric foam composites studied present superior fire‐resistance compared with conventional epoxy foam systems. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3266–3272, 2006     

Long jute fiber‐reinforced polypropylene composite: Effects of jute fiber bundle and glass fiber hybridization

Two types of long jute fiber pellet consisting of twisted‐jute yarn (LFT‐JF/PP) and untwisted‐jute yarn (UT‐JF/PP) pellets are used to prepare jute fiber–reinforced polypropylene (JF/PP) composites. The mechanical properties of both long fiber composites are compared with that of re‐pelletized pellet (RP‐JF/PP) of LFT‐JF/PP pellet, which is re‐compounded by extrusion compounding. High stiffness and high impact strength of JF/PP composites are as a result of using long fiber. However, the longer fiber bundle consequently affects the distribution of jute fiber. The incorporation of 10 wt % glass fibers is found to improve mechanical properties of JF/PP composites. Increasing mechanical properties of hybrid composites is dependent on the type of JF/PP pellets, which directly affect the fiber length and fiber orientation of glass fiber within hybrid composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41819.     

Mechanical,thermal, and dynamic mechanical properties of long glass fiber‐reinforced thermoplastic polyurethane/polyoxymethylene composites

Long glass fiber (LGF)‐reinforced thermoplastic polyurethane (TPU) elastomers and polyoxymethylene (POM) (LGF/TPU/POM) composites were prepared by using self‐designed impregnation device. Dynamic mechanical properties of the LGF/TPU/POM composites have been investigated by using dynamic mechanical thermal analysis. The results indicated that the storage modulus and glass transition temperature of the composites increase with increasing the glass fibers content and scanning frequencies. In addition, the Arrhenius relationship has been used to calculate the activation energy of α‐transition of the LGF/TPU/POM composites. The thermal stability of the LGF/TPU/POM composites was investigated by thermogravimetric analysis. The consequence demonstrated that the thermal stability increase with augmenting the content of glass fibers. The mechanical properties of the composites are investigated by a universal testing machine and a ZBC‐4 Impact Pendulum. The results demonstrated the mechanical properties of the composites aggrandize with augmenting the glass fibers content. The good dispersion of the LGFs in the matrix resins is obtained from scanning electron micrographs. POLYM. COMPOS., 35:2067–2073, 2014. © 2014 Society of Plastics Engineers     

Performance of long glass fiber‐reinforced polypropylene composites at different injection temperature

Long glass fiber‐reinforced polypropylene composites were prepared using self‐designed impregnation device. Effects of the different injection temperature on mechanical properties, crystallization, thermal, and dynamic mechanical properties of long glass fiber‐reinforced polypropylene composites were discussed. The differential scanning calorimetry (DSC) results indicate that the melting peak temperature of PP/LGF composites gradually reduced, however, the crystallinity of PP/LGF composites gradually increased with increasing injection temperature. Thermo‐gravimetric analyzer (TGA) results demonstrate that with increasing injection temperature, the temperature of the PP/LGF composites melt increased, the viscosity of the PP/LGF composites melt lowered, the mold filling of the PP/LGF composites melt was easy, the shear force of glass fiber was relatively low, which made the residual length of glass fiber in products increase. Dynamic thermal mechanical analyzer (DMA) results show that the storage modulus of PP/LGF composites is the highest while the injection temperature is at 290°C, and the peak value of tan σ of PP /LGF composites at 290°C is minimal, which indicates that the mechanical properties of PP /LGF composites at 290°C is the best. What' more, the injection temperature at 290°C significantly ameliorated “glass fiber rich skin” of products of glass fiber‐reinforced composites. J. VINYL ADDIT. TECHNOL., 24:233–238, 2018. © 2016 Society of Plastics Engineers     

Incorporation of epoxidized soybean oil as co‐matrix in epoxy resin toward developing plastisol/particulate toughened glass fiber composites

Epoxidized soybean oil was incorporated as a co‐matrix into an epoxy resin, and the hybrid resin system was used for preparing glass fiber‐reinforced composites. Effect of addition of poly(vinyl chloride) plastisol and selected particulate fillers (fly ash and wood flour) to epoxy/epoxidized soybean oil matrix on mechanical and water uptake properties of glass fiber‐reinforced composites were studied. Fourier transform infrared spectroscopy was used to reveal the curing state of these composites. It was observed that tensile strengths and moduli decreased with the inclusion of all additives. However, addition of poly(vinyl chloride) plastisol, fly ash, and wood flour particulate fillers showed significant increase in impact strengths compared with neat epoxy composite in a synergistic manner. Water uptake results of the composites were found to be in good agreement with ? OH peak intensities obtained from Fourier transform infrared spectroscopy. Finally, acousto‐ultrasonic nondestructive technique was successfully used to assess damage states and to relate stress wave factors with tensile strength properties of modified epoxy‐based glass fiber composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40586.     

Effects of sizing materials on the properties of carbon fiber‐reinforced polyamide 6,6 composites

This article aims to study the effect of the sizing materials type on the mechanical, thermal, and morphological properties of carbon fiber (CF)‐reinforced polyamide 6,6 (PA 6,6) composites. For this purpose, unsized CF and sized CFs were used. Thermogravimetric analysis was performed, and it has been found that certain amounts of polyurethane (PU) and PA sizing agents decompose during processing. The effects of sizing agent type on the mechanical and thermomechanical properties of all the composites were investigated using tensile, Izod impact strength test, and dynamic mechanical analysis. Tensile strength values of sized CF‐reinforced composites were higher than that of unsized CF‐reinforced composites. PA and polyurethane sized CF‐reinforced composites exhibited the highest impact strength values among the other sized CF‐reinforced composites. PU and PA sized CF‐reinforced composites denoted higher storage modulus and better interfacial adhesion values among the other sizing materials. Scanning electron microscope studies indicated that CFs which were sized with PU and PA have better interfacial bonding with PA 6,6 matrix among the sized CFs. All the results confirmed that PA and PU were suitable for CF's sizing materials to be used for PA 6,6 matrix. POLYM. COMPOS., 34:1583–1590, 2013. © 2013 Society of Plastics Engineers     

Properties and process ability of long fiber‐reinforced polymeric composites

The addition of nanoparticles to polymeric matrices has shown great promise for improving mechanical and thermal properties; however, this improvement comes with a decrease of processability. In this study, two different glass fabrics were used. One of them was Windstrand, a stitched equally‐biaxial R‐glass fabric the other was Advantex, a unidirectional glass fiber mat. Both of them are provided by Owens Corning. The mats were sprayed with carbon nanofibers (CNF) on both sides. Mechanical properties of composites manufactured via vacuum‐assisted resin transfer molding were obtained. Permeability, as a measure of processability, of the sprayed glass mats was measured. Mechanical properties are improved, whereas permeability decreases with the addition of CNF. POLYM. COMPOS., 35:655–664, 2014. © 2013 Society of Plastics Engineers     

Simultaneous enhancements in the mechanical,thermal, and electrical performances of glass‐fiber‐reinforced cyanate ester/epoxy composites with plasma‐functionalized carbon nanotubes at different temperatures

Woven glass‐fiber‐reinforced cyanate ester/epoxy composites modified with plasma‐functionalized multiwalled carbon nanotubes (MWCNTs) were prepared. The mechanical, thermal, and electrical properties of the composites were investigated at different temperatures. The results show that the interlaminar shear strength, thermal conductivity, and electrical conductivity of the composites at room temperature and the cryogenic temperatures were enhanced simultaneously by the incorporation of MWCNTs, whereas the nonconductive behavior of the composites as electrical insulating materials was not changed. Meanwhile, the reinforcing mechanism was also examined on the basis of the microstructure of the composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41418.     

Short‐beam and three‐point‐bending tests for the study of shear and flexural properties in unidirectional‐fiber‐reinforced epoxy composites

The bending properties of composite materials are often characterized with simply supported beams under concentrated loads. The results from such tests are commonly based on homogeneous beam equations. For laminated materials, however, these formulas must be modified to account for the stacking sequence of the individual plies. The horizontal shear test with a short‐beam specimen in three‐point bending appears suitable as a general method of evaluation for the shear properties in fiber‐reinforced composites because of its simplicity. In the experimental part of this work, the shear strength of unidirectional‐glass‐fiber‐reinforced epoxy resin composites was determined in different fiber directions with the short‐beam three‐point‐bending test. Also, the elastic constants and flexural properties of the same materials were determined from bending experiments carried out on specimens in the 0, 15, 30, 45, 60, 75, and 90° fiber directions with high span–thickness ratios. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 63–74, 2004     

On the analysis of force during secondary processing of natural fiber‐reinforced composite laminates

The rising concern regarding global warming has ignited a quest in the research fraternity towards development of sustainable materials that can reduce the carbon footprint. Natural fiber reinforced composites have made an excellent impression in the area of sustainable development because of their environmental and ecological aspects. These materials are widely used for manufacturing of engineering products. But, the use of natural fiber composites for engineering applications necessitates making of holes in order to ascertain assembly of several components by means of mechanical fastening. In this research endeavor, the drilling behavior of nettle/polypropylene (PP) composites has been experimentally investigated. The relative significance of the input process variables has also been studied with the help of statistical technique called analysis of variance (ANOVA). The present study established few significant facts in context of drilling of natural fiber reinforced composites. It has been observed that the facts established for drilling of synthetic fiber reinforced thermoset composites cannot be directly applied for natural fiber reinforced composites. POLYM. COMPOS., 38:164–174, 2017. © 2015 Society of Plastics Engineers     

Mechanical and thermal properties of hierarchical composites enhanced by pristine graphene and graphene oxide nanoinclusions

Epoxy resin nanocomposites incorporated with 0.5, 1, 2, and 4 wt % pristine graphene and modified graphene oxide (GO) nanoflakes were produced and used to fabricate carbon fiber‐reinforced and glass fiber‐reinforced composite panels via vacuum‐assisted resin transfer molding process. Mechanical and thermal properties of the composite panels—called hierarchical graphene composites—were determined according to ASTM standards. It was observed that the studied properties were improved consistently by increasing the amount of nanoinclusions. Particularly, in the presence of 4 wt % GO in the resin, tensile modulus, compressive strength, and flexural modulus of carbon fiber (glass fiber) composites were improved 15% (21%), 34% (84%), and 40% (68%), respectively. Likewise, with inclusion of 4 wt % pristine graphene in the resin, tensile modulus, compressive strength, and flexural modulus of carbon fiber (glass fiber) composites were improved 11% (7%), 30% (77%), and 34% (58%), respectively. Also, thermal conductivity of the carbon fiber (glass fiber) composites with 4% GO inclusion was improved 52% (89%). Similarly, thermal conductivity of the carbon fiber (glass fiber) composites with 4% pristine graphene inclusion was improved 45% (80%). The reported results indicate that both pristine graphene and modified GO nanoflakes are excellent options to enhance the mechanical and thermal properties of fiber‐reinforced polymeric composites and to make them viable replacement materials for metallic parts in different industries, such as wind energy, aerospace, marine, and automotive. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40826.     

Investigation on phosphorus halogen‐free flame‐retardancy systems in short glass fiber‐reinforced PC/ABS composites under rapid thermal cycle molding process condition

In this study, standard test specimens with flame‐retarded short glass fiber‐reinforced PC/ABS materials were fabricated under rapid thermal cycle injection molding condition by selecting a potassium perfluorobutane sulfonate flame retardant specially used for PC, FR2025, and two kinds of aryl phosphorus halogen‐free flame retardants, UN707 and PX‐220. The flame‐retardancy effect of the above different flame retardants on the studied systems was compared through combustion tests of the specimens. Meanwhile, the thermal and mechanical properties of flame‐retarded composites were studied by using the thermogravimetry analysis, dynamic mechanical thermal analysis (DMTA), and universal testing machine. The results show that the “candlewick effect” of fibers exacerbates the fire behavior of composites. With the increase of the aryl phosphorus halogen‐free flame retardants, the flame‐retardancy effect of composites is obviously improved, and the maximum thermal degradation rate of composites is significantly decreased. The UL94 combustion rating is improved, and the time of residual flame is substantially reduced with the increase of PC content under the same content of flame retardant. The DMTA results show that the flame retardants have a reinforcement action on PC/ABS matrix. However, the macroscopic mechanical properties are slightly decreased in the glass fiber‐reinforced composites because of the destructive effect of the flame retardants on the interface compatibility between matrix and fibers; the scanning electron microscopic micrographs of tensile fracture fully prove this action mechanism of flame retardants. In addition, the addition of toughener and antidripping additive significantly affects the flame retardancy and mechanical properties of composites. POLYM. COMPOS., 36:1653–1663, 2015. © 2014 Society of Plastics Engineers     

Glass‐fiber‐reinforced wood/plastic composites

The usage of wood‐plastic composites (WPCs) is rapidly growing because of their many advantages. However, they still suffer from lack of strength and toughness, which can be improved by adding a small amount of glass fiber reinforcement (GFR). Tensile tests of high‐density polyethylene WPC specimens with varying amounts of wood fiber content and 5% of GFR were carried out. Significant improvements in properties were observed. J. VINYL ADDIT. TECHNOL., 2008. © 2008 Society of Plastics Engineers.     

Sulphur‐vulcanized polybutadiene as a matrix in glass fiber‐reinforced composite materials

The basic material used in this work was a low‐molecular‐weight polybutadiene with isocyanate endgroups in the main chain. The isocyanate groups were used for crosslinking of the oligomeric polybutadiene with glycerol as a three‐functional crosslinker. The prepared polybutadiene‐based polyurethane gel was subsequently vulcanized with sulphur. The effect of sulphur content on mechanical and electrical properties of resulting materials was investigated with the aim to find an optimum matrix composition for the preparation of composite materials. Several types of glass fiber fabric reinforcement differing in fabric weight and fabric ply thickness were tested. Mechanical properties of composites based on the optimum matrix composition and different types of glass fibers were measured and compared. Being vulcanized with sulphur, the polybutadiene was found to possess improved mechanical properties and retain an excellent electroinsulating character. Moreover, the sulphur‐vulcanized polybutadiene was proved good as a matrix for the preparation of glass fiber‐reinforced composite materials having enhanced tensile and flexural properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Flexural properties of S‐2 glass and TR30S carbon fiber‐reinforced epoxy hybrid composites

A study on the flexural properties of hybrid composites reinforced by S‐2 glass and TR30S carbon fibers is presented in this article. Test specimens were made by the hand lay‐up process in an intraply configuration with varying numbers of glass/epoxy laminas substituted for carbon/epoxy laminas. These specimens were then tested in the three point bend configuration in accordance with ASTM D790‐07 at a span to depth ratio of 32. The failed specimens were examined under an optical microscope, and the results show that the dominant failure mode is at the compressive side. The flexural behavior was also simulated by finite element analysis (FEA). Based on the FEA results, the flexural modulus and flexural strength were calculated. Good agreement is found between the experiments and FEA. It is shown that flexural modulus decreases with increasing percentage of S‐2 glass fibers, positive hybrid effects exist by substituting carbon fibers for glass fibers, and applying a thin layer of S‐2 glass fiber‐reinforced polymer on the compressive surface yields the highest flexural strength. The modeling approach presented will pave a way to the effective design of hybrid composites. POLYM. COMPOS., © 2012 Society of Plastics Engineers     

Taguchi method to optimize the micron and submicron size cenosphere particulates filled E‐glass fiber‐reinforced vinylester composites

In this work, the mechanical and tribological characteristics of E‐glass fiber‐reinforced vinylester composites have been investigated experimentally under dry sliding conditions. The E‐glass fiber‐reinforced vinylester composites with uniform micron and submicron size cenosphere particulates of three different sizes (2 µm, 900 nm, and 400 nm) had been prepared in the laboratory. In this work the effect of parameters such as applied normal load, particulate size, sliding speed, sliding distance and roughness on friction and wear behavior have been carried. A plan of experiments, based on the Taguchi design, was performed to acquire data in a controlled way. An orthogonal array L₂₇ (3¹³) and Analysis of variance (ANOVA) have been applied to investigate the influence of process parameters on the coefficient of friction (COF) and sliding wear behavior of these composites. It was found that the submicron size particulates 400 nm as filler contributed significantly to improve the mechanical properties and wear resistance of the composites. The experimental results indicate that the specific wear rate is greatly influenced by applied normal load and particle size. ANOVA results showed that the applied normal load significantly influence the specific wear rate of cenosphere filled glass fiber‐reinforced vinylester composites. Regression analysis is carried to check the suitability of the prediction equation and modeling of the wear parameters and the typical R² values for COF and specific wear rate are 86.7 and 94.3%, respectively. The scanning electron microscopy are used clarify the experimental in the frictional and wear testing. POLYM. COMPOS., 35:775–787, 2014. © 2013 Society of Plastics Engineers     

Synthetic fibers and thermoplastic short‐fiber‐reinforced polymers: Properties and characterization

Among the synthetic fibers, glass fibers (GF) are most widely used in thermoplastic short‐fiber‐reinforced polymers (SFRP), as they offer good strength and stiffness, impact resistance, chemical resistance, and thermal stability at a low price. Carbon fibers (CF) are applied instead of GF, when highest stiffness is required. Other types of synthetic fibers like aramid (AF), basalt (BF), polyacrylonitrile (PAN‐F), polyethylene terephthalate (PET‐F), or polypropylene fibers (PP‐F) are rarely used in SFRP, although they offer some advantages compared with GF. The aim of this article is, to give an overview of various fiber types with regard to their mechanical properties, densities, and prices as well as the performance of their thermoplastic composites. The mechanical properties are presented as Ashby plots of tensile strength versus tensile modulus, both in absolute and specific (absolute value divided by density) values. This overview also focuses on modification of fiber/matrix interaction, as interfacial adhesion has a huge impact on composite performance. A summary of established methods for characterization of fibers, polymers, and composites completes this article. POLYM. COMPOS., 35:227–236, 2014. © 2013 Society of Plastics Engineers