Phase stability,microstructural evolution and room temperature mechanical properties of TiO2 doped 8 mol% Y2O3 stabilized ZrO2 (8Y-CSZ)

The effect of TiO₂ dopant on phase stability, microstructural evolution and room temperature mechanical properties of 8 mol% yttria-stabilized cubic zirconia (8Y-CSZ) was studied. The results show that TiO₂ (up to 10 wt%) can be dissolved in solid solution in the zirconia matrix. When the dopant amount is less than 5 wt%, TiO₂ doped 8Y-CSZ remains single phase cubic zirconia. Increased additions of TiO₂ destabilize the cubic phase and cause the formation of tetragonal zirconia with a resultant microstructure consisting of large cubic zirconia grains and small tetragonal zirconia grains. EDS analyses show that yttria is partitioned between these two types of grains. The solubility of TiO₂ is the highest for cubic grains which also have higher yttria concentrations. Room temperature mechanical property measurements show that hardness does not change significantly with additions of TiO₂, but fracture toughness is more than doubled for 10 wt% TiO₂ doped 8Y-CSZ.     

Developments on the mechanical properties of MgO-MgAl2O4 composite refractories by ZrSiO4-3 mol% Y2O3 addition

Improvements and the effects of additions of ZrSiO₄-3 mol% Y₂O₃ into MgO-MgAl₂O₄ composite refractories on mechanical properties and thermal stress resistance parameters were investigated. Significant improvements were achieved on mechanical properties and R-R_st parameters up to ∼2 and ∼3-fold ratios. The major parameters improving mechanical properties and thermal behaviour of refractories were determined as follows: (i) the increase in resistance to crack initiation and propagation due to formation of Mg₂SiO₄ phase after decomposition of zircon; (ii) propagation of the microcracks formed in the structure for a short distance by interlinking each other; (iii) arresting or deviation of microcracks when reaching pores or ZrO₂ grains released after dissociation of zircon, located together with Y₂O₃ particles, and furthermore; (iv) co-presence of both intergranular and transgranular types of cracks, and with incorporation of zircon-Y₂O₃; (v) increase in density; and (vi) a significant reduction in MgO grain size.     

Carbon dioxide reforming of ethanol over Ni/Y2O3–ZrO2 catalysts

Supported nickel catalysts of composition Ni/Y₂O₃–ZrO₂ were synthesized in one step by the polymerization method and compared with a nickel catalyst prepared by wet impregnation. Stronger interactions were observed in the formed catalysts between NiO species and the oxygen vacancies of the Y₂O₃–ZrO₂ in the catalysts made by polymerization, and these were attributed to less agglomeration of the NiO during the synthesis of the catalysts in one step. The dry reforming of ethanol was catalyzed with a maximum CO₂ conversion of 61% on the 5NiYZ catalyst at 800 °C, representing a better response than for the catalyst of the same composition prepared by wet impregnation.     

Sintering mechanism and dielectric properties of LiTaO3 matrix composites with the addition of Al2O3 particles

Highly densified Al₂O₃/LiTaO₃ (ALT) ceramic composites were fabricated by hot-pressing in a nitrogen atmosphere. The addition of Al₂O₃ particles could significantly improve the densification of LiTaO₃. Sintering mechanism of the LiTaO₃ ceramic incorporated with Al₂O₃ particles is proposed. Dielectric constant of 5 vol.% Al₂O₃/LiTaO₃ (5ALT) composite ceramic was slightly increased in the range from 30 kHz to 10⁶ Hz, but the dielectric loss was lowered in the whole range from 10³ Hz to 10⁶ Hz. Piezoelectric constant (d₃₃) of the 5ALT ceramic composite is about 50% of that of LiTaO₃ single crystal.     

Laser stereolithography of ZrO2 toughened Al2O3

Ceramic laser stereolithography is a manufacturing process suitable candidate for the production of complex shape technical ceramics. The green ceramic is produced layer by layer through laser polymerisation of UV curable ceramic suspensions. A number of critical issues deserve attention: high solid loading and low viscosity of the suspensions, high UV reactivity, prevention of interlayer delamination in the green and in the sintered body, good mechanical performance. In this work, ZrO₂-reinforced Al₂O₃ components have been obtained from an acrylic modified zircon loaded with alumina powders. The zircon compound is effective as organic photoactivated resin and allows the dispersion of a high volume fraction of Al₂O₃ powder (up to 50 vol.%) while keeping viscosity at reasonable low values. The zircon compound also represents a liquid ceramic precursor that converts to oxide after burning out of the binder. Thank to the good dispersion of the alumina powder in the zircon acrylate, a uniform dispersion of ZrO₂ submicron particles is obtained after pyrolysis. These are located at the grain boundaries between alumina grains. Formation of both monoclinic and tetragonal ZrO₂ occurs as evidenced by XRD. No delamination occurs in bending tests as evidenced by SEM fractography, satisfactory modulus and strength values were concurrently found.     

Influence of sintering temperature and holding time on the densification, phase transformation, microstructure and properties of hot pressing WC-40 vol.%Al2O3 composites

WC-40 vol.%Al₂O₃ composites were prepared by high energy ball milling followed by hot pressing. The tungsten carbide (WC) and commercial alumina (Al₂O₃) powders composed of amorphous Al₂O₃, boehmite (AlOOH) and χ-Al₂O₃ were used as the starting materials. The phase transformation during sintering, the influence of sintering temperature and holding time on the densification, microstructure, Vickers hardness and fracture toughness and the toughening effects of WC-40 vol.%Al₂O₃ composites were investigated. The results showed that the amorphous Al₂O₃, AlOOH and χ-Al₂O₃ were transformed to α-Al₂O₃ completely during the sintering process. With the increasing sintering temperature and holding time, the relative density increased and both the Vickers hardness and fracture toughness increased initially to the maximum values and then decreased. When the as milled powders were hot pressed at 1540 °C for 90 min, a relative density of 97.98% and a maximum hardness of 18.65 GPa with an excellent fracture toughness of 10.43 MPa m^1/2 of WC-40 vol.%Al₂O₃ composites were obtained.     

Preparation of ZrO2/Gd2O3 composite ceramic materials by coprecipitation method

High burnup is a goal for further development of advanced nuclear power in the future. However, along with the increase of burnup, it becomes more diffidult to control reactor reactivity, which affects the operation safety of the nuclear reactor. Al₂O₃/B₄C burnable poison materials widely used in pressurized water reactor currently will not meet the requirements of burnable poison materials in high burnup nuclear power. Because of the better performance of ZrO₂/Gd₂O₃ burnable poison materials than that of Al₂O₃/B₄C, this paper studies the preparation of ZrO₂/Gd₂O₃ composite ceramic materials by the coprecipitation method. The experimental results show that at the sintering temperature of 1500–1650 °C, ZrO₂/Gd₂O₃ composite ceramic grains are small, compact and uniform with the generation of homogeneous solid solution. At 1600 °C, ZrO₂–10%Gd₂O₃ has the highest density and mechanical strength.     

Processing and mechanical properties of ZrO2–TiB2 composites

In this paper, a strategy is described to develop high toughness yttria-stabilised tetragonal zirconia polycrystalline (Y-TZP) composites reinforced with hard TiB₂ particles. The experimental results revealed that fully dense Y-TZP composites with 30 vol.% TiB₂ can be obtained with a moderate hardness of 13 GPa, a high strength up to 1280 MPa and an excellent indentation toughness up to 10 MPa m^1/2 by hot pressing in vacuum at 1450 °C. The toughness of the composites can be tailored between 4 and 10 MPa m^1/2 by varying the yttria stabiliser content of the ZrO₂ matrix between 3 and 2 mol%. An optimum composite toughness was achieved for a ZrO₂ matrix with an overall yttria content of 2.5 mol%, obtained by mixing pure monoclinic and 3 mol% Y₂O₃ co-precipitated ZrO₂ starting powders. An important observation is that the thermal residual tensile stress in the ZrO₂ matrix due to the TiB₂ addition, needs to be taken into account when optimising the transformability of the ZrO₂ matrix in order to develop high toughness Y-TZP composites.     

Matrix–filler interactions in polysilazane-derived ceramics with Al2O3 and ZrO2 fillers

Interactions between a poly(vinyl)silazane and Al₂O₃ or Y₂O₃-stabilised ZrO₂ fillers were studied during the fabrication of polysilazane-derived bulk ceramics in order to investigate the influence of oxide fillers on resulting properties. Specimens were produced by coating of the filler powders with the polysilazane, warm-pressing of the resulting composite powders, and pyrolytic conversion in flowing N₂ at various temperatures between 1000 °C and 1400 °C. Significant differences in densification were observed, depending on the filler used. Reactions between the polysilazane-derived matrix and Al₂O₃ or ZrO₂ at temperatures ≥1300 °C resulted in the formation of Si₅AlON₇ or ZrSiO₄, respectively. Reactivity in the polysilazane-derived component was a result of SiO₂ contamination caused primarily by adsorbed species on the filler particle surface. Knowledge of polysilazane/filler interface processes is found to be decisive for the prediction of properties such as shrinkage and porosity, which heavily influence performance of a material.     

Preparation and properties of β-CaSiO3/ZrO2 (3Y) nanocomposites

β-CaSiO₃/ZrO₂ (3Y) nanocomposites were successfully fabricated by spark plasma sintering (SPS) technique. The addition of nanocrystalline ZrO₂ could inhibit the phase transition of micrometer sized CaSiO₃ and increase its phase transitional temperature. The relative densities of the dense β-CaSiO₃/ZrO₂ nanocomposites were above 98%. Nanocrystalline ZrO₂ has formed a network structure in the nanocomposites, which could improve the mechanical properties of nanocomposites. The fracture strength and fracture toughness of the nanocomposites were as high as 395 MPa and 4.08 MPa m^1/2, respectively. The nanocomposites showed good in vitro bioactivity with hydroxyapatite (HA) layer formation on the ZrO₂ network of the nanocomposites in simulated body fluid. The spark plasma sintered β-CaSiO₃/ZrO₂ (3Y) nanocomposite may provide a new bone graft for load bearing applications.     

Reduction and oxidation properties of Fe2O3/ZrO2 oxygen carrier for hydrogen production

Fe₂O₃ is a promising oxygen carrier for hydrogen production in the chemical-looping process. A set of kinetic studies on reduction with CH₄, CO and H₂ respectively, oxidation with water and oxygen containing Ar for chemical-looping hydrogen production was conducted. Fe₂O₃ (20 wt.%)/ZrO₂ was prepared by a co-precipitation method. The main variables in the TGA (thermogravimetric analyzer) experiment were temperatures and gas concentrations. The reaction kinetics parameters were estimated based on the experimental data. In the reduction by CH₄, CO and H₂, the reaction rate changed near FeO. Changes in the reaction rate due to phase transformation were observed at low temperature and low gas concentration during the reduction by CH₄, but the phenomenon was not remarkable for the reduction by CO and H₂. The reduction rate achieved using CO and H₂ was relatively faster than achieved using CH₄. The Hancock and Sharp method of comparing the kinetics of isothermal solid-state reactions was applied. A phase boundary controlled model (contacting sphere) was applied to the reduction of Fe₂O₃ to FeO by CH₄, and a different phase boundary controlled model (contacting infinite slab) was fit well to the reduction of FeO to Fe by CH₄. The reduction of Fe₂O₃ to Fe by CO and H₂ can be described by the former phase boundary controlled model (contacting sphere). This phase boundary controlled model (contacting sphere) also fit well for the oxidation of Fe to Fe₃O₄ by water and FeO to Fe₂O₃ by oxygen containing Ar. These kinetics data could be used to design chemical-looping hydrogen production systems.     

Synthesis and sintering of Y2O3-doped ZrO2 powders using two Pechini-type gel routes

Yttria-tetragonal zirconia polycrystal (ZrO₂ + 4.5 mol% Y₂O₃) nanocrystalline powder was synthesized by two Pechini-type gel routes, the in situ polymerized complex (IPC) method and the PEG/AF method. FTIR spectra confirmed coordination of metal ions with the polymer by different routes, depending on the method used. The crystallite size of the powder increased from 5 nm to 8 nm when the temperature was increased from 450 °C to 600 °C and calcination times increased from 2 h to 24 h. The morphology of the powders differed only when the organic impurities were not completely eliminated. After calcination, the morphology of the powders produced by the two methods showed porous agglomerates composed of smaller particles. All the resulting microstructures were very similar, regardless of the method employed to obtain the powder or the calcination times and temperatures.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Enhanced mechanical properties of 3 Y2O3 stabilized tetragonal ZrO2 incorporating tourmaline particles

The current study reports on the improvement of mechanical properties of 3?mol% Y₂O₃ stabilized tetragonal ZrO₂ (3Y-TZP) by introduction of tourmaline through ball milling and subsequent densification by pressureless sintering at 800, 1200, 1300, 1400?°C. Findings demonstrate that no matter which sintering temperature the 3Y-TZP ceramic containing 2?wt% tourmaline reach a maximum value in flexural strength and fracture toughness as compared to other composite ceramics. As the tourmaline content is 2?wt% and the sintering temperature is 1300?°C, the flexural strength and fracture toughness of the composite ceramics are the highest, increases of 36.2% and 36.6% over plain 3Y-TZP ceramic respectively. The unique microstructure was systematically investigated through X-ray diffraction, scanning electron microscopy, energy dispersive spectrum, and flourier transform-infrared. The strengthening and toughening mechanism of tourmaline in 3Y-TZP ceramic were also discussed.     

Synthesis and study on phase diagram of 1-10 mol% SnO2-doped Bi2O3

Bi₂O₃ materials doped with various SnO₂ concentrations were prepared by colloidal process and solid state reactions to achieve high density and uniform microstructure. Thermal behavior, and crystalline phases of the SnO₂-doped Bi₂O₃ (BSO) samples were investigated by differential thermal analyses, X-ray diffraction, and scanning electron microscopy. A new phase diagram of Bi₂O₃-(1-10 mol%) SnO₂ system is proposed in this study. The results show that 1 mol% SnO₂ doped concentration is totally dissolved in Bi₂O₃ without the existence of any impurity phases as compared to higher doping SnO₂ concentration.     

Reduction of NO by CO on Cu/ZrO2/Al2O3 catalysts: Characterization and catalytic activities

ZrO₂, γ-Al₂O₃ and ZrO₂/γ-Al₂O₃-supported copper catalysts have been prepared, each with three different copper loads (1, 2 and 5 wt%), by the impregnation method. The catalysts were characterized by nitrogen adsorption (BET), X-ray diffraction (XRD), temperature programmed reduction (TPR) with H₂, Raman spectroscopy and electronic paramagnetic resonance (EPR). The reduction of NO by CO was studied in a fixed-bed reactor packed with these catalysts and fed with a mixture of 1% CO and 1% NO in helium. The catalyst with 5 wt% copper supported on the ZrO₂/γ-Al₂O₃ matrix achieved 80% reduction of NO. Approximately the same rate of conversion was obtained on the catalyst with 2 wt% copper on ZrO₂. Characterization of these catalysts indicated that the active copper species for the reduction of NO are those in direct contact with the oxygen vacancies found in ZrO₂.     

Enhancement of oxygen storage capacity by reductive treatment of Al2O3 and CeO2–ZrO2 solid solution nanocomposite

Oxygen storage capacity (OSC) of CeO₂–ZrO₂ solid solution, Ce_xZr_(1−x)O₄, is one of the most contributing factors to control the performance of an automotive catalyst. To improve the OSC, heat treatments were employed on a nanoscaled composite of Al₂O₃ and CeZrO₄ (ACZ). Reductive treatments from 700 to 1000 °C significantly improved the complete oxygen storage capacity (OSC-c) of ACZ. In particular, the OSC-c measured at 300 °C reached the theoretical maximum with a sufficient specific surface area (SSA) (35 m²/g) after reductive treatment at 1000 °C. The introduced Al₂O₃ facilitated the regular rearrangement of Ce and Zr ions in CeZrO₄ as well as helped in maintaining the sufficient SSA. Reductive treatments also enhanced the oxygen release rate (OSC-r); however, the OSC-r variation against the evaluation temperature and the reduction temperature differed from that of OSC-c. OSC-r measured below 200 °C reached its maximum against the reduction temperature at 800 °C, while those evaluated at 300 °C increased with the reduction temperature in the same manner as OSC-c.     

Structural and optical properties of Tm:Y2O3 transparent ceramic with La2O3, ZrO2 as composite sintering aid

The paper reports the use of La₂O₃ and ZrO₂ co-doping as a composite sintering aid for the fabrication of Tm:Y₂O₃ transparent ceramics. Two groups of experiments were conducted for investigating the influences of composite sintering aids on the microstructures and the optical properties of Tm:Y₂O₃ transparent ceramics in contrast to single La³⁺ and single Zr⁴⁺ doped Tm:Y₂O₃. Samples with composite sintering aids could realize fine microstructures and good optical properties at relatively low sintering temperatures. Grain sizes around 10 μm and transmittances close to theoretical value at wavelength of 2 μm were achieved for the 9 at.% La³⁺, 3 at.% Zr⁴⁺ co-doped samples sintered at 1500-1600 °C. The influences of the composite sintering aids on the emission intensities and the phonon energies of Tm:Y₂O₃ ceramics were also investigated.     

Study of ruthenium supported on Ta2O5–ZrO2 and Nb2O5–ZrO2 as catalysts for the partial oxidation of methane

Ru-based catalysts supported on Ta₂O₅–ZrO₂ and Nb₂O₅–ZrO₂ are studied in the partial oxidation of methane at 673–873 K. Supports with different Ta₂O₅ or Nb₂O₅ content were prepared by a sol–gel method, and RuCl₃ and RuNO(NO₃)₃ were used as precursors to prepare the catalysts (ca. 2 wt.% Ru). At 673 K high selectivity to CO₂ was found. An increase of temperature up to 773 K produced an increase in the selectivity to syngas (H₂/CO = 2.2–3.1), and this is related with the transformation of RuO₂ to metallic Ru as was determined from XRD and XPS results. At 873 K and with co-fed CO₂ an increase of the catalytic activity and CO selectivity was found. A TOF value of 5.7 s⁻¹ and H₂/CO ratio ca. 1 was achieved over Ru(Cl)/6TaZr. Catalytic results are discussed as a function of the support composition and characteristics of Ru-based phases.     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.