Measuring the mass of an electron by LC/TOF-MS: a study of "twin ions"

While investigating the in-source CID fragmentation of nonsteroidal antiinflammatory drugs (NSAIDs), it was noticed that the same fragment ion (nominal mass) formed in either positive or negative ion electrospray for a suite of NSAIDs. For example, ibuprofen with a molecular mass of 206, fragments to the m/z 161 ion in negative ion from its deprotonated molecule (m/z 205, [M - H]-) and fragments to the m/z 161 ion in positive ion from its protonated molecule (m/z 207, [M + H]+). This fragment ion was euphemistically called a "twin ion"because of the same nominal mass despite opposite charge. The CID fragmentation of the twin ions was confirmed also by LC/MS/MS ion trap. Accurate mass measurements in negative ion show that the loss was due to CO2 (measured loss of 43.9897 atomic mass units (u) versus calculated loss of 43.9898 u for N = 10) and in positive ion the loss is due to HCOOH (measured loss of 46.0048 u versus calculated loss of 46.0055 u, N = 10). It was realized that, in fact, the ions were not "identical mass twins of opposite charge" but separated in accurate mass by two electrons. The accurate mass measurement by liquid chromatography/time-of-flight-mass spectrometry (LC/TOF-MS) can distinguish between the two fragment ions of ibuprofen (161.13362 +/- 0.00019 and 161.13243 +/- 0.00014 for N = 20). This experiment was repeated for two other NSAIDs, and the mass of an electron was measured as the difference between the twin ions, which was 0.00062 u +/- 14.8% relative standard deviation (N = 20 analyses). Thus, the use of continuous calibration makes it possible to measure the mass of an electron within one significant figure using the NSAID solution. This result shows the importance of including electron mass in accurate mass measurements and the value of a benchmark test for LC/TOF-MS mass accuracy.     

Inlet ionization: a new highly sensitive approach for liquid chromatography/mass spectrometry of small and large molecules

Inlet ionization is a new approach for ionizing both small and large molecules in solids or liquid solvents with high sensitivity. The utility of solvent based inlet ionization mass spectrometry (MS) as a method for analysis of volatile and nonvolatile compounds eluting from a liquid chromatography (LC) column is demonstrated. This new LC/MS approach uses reverse phase solvent systems common to electrospray ionization MS. The first LC/MS analyses using this novel approach produced sharp chromatographic peaks and good quality full mass range mass spectra for over 25 peptides from injection of only 1 pmol of a tryptic digest of bovine serum albumin using an eluent flow rate of 55 μL min(-1). Similarly, full acquisition LC/MS/MS of the MH(+) ion of the drug clozapine, using the same solvent flow rate, produced a signal-to-noise ratio of 54 for the major fragment ion with injection of only 1 μL of a 2 ppb solution. LC/MS results were acquired on two different manufacturer's mass spectrometers using a Waters Corporation NanoAcquity liquid chromatograph.     

Accurate mass liquid chromatography/mass spectrometry on quadrupole orthogonal acceleration time-of-flight mass analyzers using switching between separate sample and reference sprays. 2. Applications using the dual-electrospray ion source

A new electrospray dual sprayer, LockSpray, was developed for accurate mass measurements on a quadrupole orthogonal acceleration time-of-flight mass spectrometer (oa-Q-ToF). With the dual-sprayer ion source, both sprays are orthogonal to each other. A mechanism similar to the one employed on the multiplexed electrospray source (MUX) allows switching between reference and sample sprayer. The reference sprayer is optimized for low flow rates, whereas the sample sprayer is a conventional Z-spray type sprayer. Earlier work using a modified MUX ion source on an orthogonal acceleration time-of-flight instrument showed promising results. In this paper, examples obtained with the LockSpray, specifically designed for accurate mass measurements on an oa-Q-ToF, are presented. The examples include results obtained for the identification of impurities in drug substances such as cimetidine and rosiglitazone, using accurate mass tandem mass spectrometry in both positive and negative ion electrospray modes. Good mass accuracies, i.e., within 2 mDa of the theoretical value, were obtained in MS and MS/MS operation.     

Structural characterization of protein tryptic peptides via liquid chromatography/mass spectrometry and collision-induced dissociation of their doubly charged molecular ions

The formation of multiply charged molecular ions via the field-assisted ion evaporation mechanism during electrospray ionization enables the use of an atmospheric pressure ionization quadrupole mass spectrometer system for characterizing biologically important peptides. The straightforward implementation of high-performance liquid chromatography (HPLC) into this new strategy to determine the molecular weight of tryptic peptides via the pneumatically assisted electrospray (ion spray) interface is presented. Examples utilizing both microbore (1.0 mm) and standard bore (4.6 mm) inside diameter columns are shown for the LC/MS molecular weight determination of tryptic peptides in methionyl-human growth hormone (met-hGH). Injected levels from 50 to 75 pmol of tryptic digest onto 1 mm i.d. HPLC columns provided full-scan LC/MS or LC/MS/MS results without postcolumn splitting of the effluent. When standard 4.6 mm i.d. HPLC columns were used, a 20:1 postcolumn split was utilized, which required from 1 to 5 nmol of injected tryptic digest for full-scan LC/MS or LC/MS/MS results. Collision-induced dissociation (CID) mass spectra resulting from either "infusion" or on-line LC/MS/MS analysis of the abundant doubly charged ions that predominate for tryptic peptides under electrospray conditions provided structurally useful sequence information for met-hGH and human hemoglobin tryptic digests. The slower mass spectrometer scan rate used during infusion of sample provides more accurate mass assignments than on-line LC/MS or LC/MS/MS, but the latter on-line experiments preclude ambiguities caused by matrix or component interferences. However, in some instances very weak CID product ions preclude complete tryptic peptide structural characterization based upon the CID data alone.(ABSTRACT TRUNCATED AT 250 WORDS)     

Metabolite identification using automated comparison of high-resolution multistage mass spectral trees

Multistage mass spectrometry (MS(n)) generating so-called spectral trees is a powerful tool in the annotation and structural elucidation of metabolites and is increasingly used in the area of accurate mass LC/MS-based metabolomics to identify unknown, but biologically relevant, compounds. As a consequence, there is a growing need for computational tools specifically designed for the processing and interpretation of MS(n) data. Here, we present a novel approach to represent and calculate the similarity between high-resolution mass spectral fragmentation trees. This approach can be used to query multiple-stage mass spectra in MS spectral libraries. Additionally the method can be used to calculate structure-spectrum correlations and potentially deduce substructures from spectra of unknown compounds. The approach was tested using two different spectral libraries composed of either human or plant metabolites which currently contain 872 MS(n) spectra acquired from 549 metabolites using Orbitrap FTMS(n). For validation purposes, for 282 of these 549 metabolites, 765 additional replicate MS(n) spectra acquired with the same instrument were used. Both the dereplication and de novo identification functionalities of the comparison approach are discussed. This novel MS(n) spectral processing and comparison approach increases the probability to assign the correct identity to an experimentally obtained fragmentation tree. Ultimately, this tool may pave the way for constructing and populating large MS(n) spectral libraries that can be used for searching and matching experimental MS(n) spectra for annotation and structural elucidation of unknown metabolites detected in untargeted metabolomics studies.     

Protocol for liquid chromatography/mass spectrometry of glutathione conjugates using postcolumn solvent modification

A novel protocol for thermospray liquid chromatography/mass spectrometry (LC/MS) analysis of mixtures of glutathione conjugates is reported. Solvent conditions for optimal high-performance liquid chromatography are not always the same as for optimal thermospray ionization mass spectrometry. Labile glutathione conjugates that give poor spectra in aqueous ammonium acetate yield more intense molecular ion signals with increased percentages of acetonitrile. Direct injection thermospray ionization using 30-60% acetonitrile in aqueous ammonium acetate produced protonated molecular ions for glutathione conjugates of menadione, styrene oxide, pentachlorophenyl methyl sulfone, chlorodinitrobenzene, and chlorambucil. Since, the high percentages of organic modifier needed for good molecular ion intensity preclude chromatographic separation of these polar compounds, successful graphic separation of these polar compounds, successful LC/MS was facilitated by postcolumn addition of organic modifiers to the mobile phase. This new methodology allowed excellent chromatographic separations and thermospray ionization mass spectra to be obtained for a mixture of haloalkane glutathione conjugates. Moreover, cleavage of the gamma-glutamyl-cysteine amide bond of glutathione results in class-characteristic fragment ions. Changes in the fragmentation pathways in spectra acquired with and without organic modifiers shed light on the importance of the desolvation process in obtaining good molecular ion sensitivity in thermospray.     

In-spray supercharging of peptides and proteins in electrospray ionization mass spectrometry

Enhanced charging, or supercharging, of analytes in electrospray ionization mass spectrometry (ESI MS) facilitates high resolution MS by reducing an ion mass-to-charge (m/z) ratio, increasing tandem mass spectrometry (MS/MS) efficiency. ESI MS supercharging is usually achieved by adding a supercharging reagent to the electrospray solution. Addition of these supercharging reagents to the mobile phase in liquid chromatography (LC)-MS/MS increases the average charge of enzymatically derived peptides and improves peptide and protein identification in large-scale bottom-up proteomics applications but disrupts chromatographic separation. Here, we demonstrate the average charge state of selected peptides and proteins increases by introducing the supercharging reagents directly into the ESI Taylor cone (in-spray supercharging) using a dual-sprayer ESI microchip. The results are comparable to those obtained by the addition of supercharging reagents directly into the analyte solution or LC mobile phase. Therefore, supercharging reaction can be accomplished on a time-scale of ion liberation from a droplet in the ESI ion source.     

Determination of ethylenethiourea in crops using particle beam liquid chromatography/mass spectrometry.

Several food crops were analyzed for residues of ethylenethiourea (ETU), a suspect thyroid and liver carcinogen present in EBDC fungicides, using a commercial particle beam (PB) LC/MS method. The PB/LC/MS detection limits for ETU in crops (5 ppb, 1.25 ng) are comparable to those obtained by LC with electrochemical detection. Spectra obtained from crop samples containing as little as 5 ng of ETU were matched with the NBS library reference EI spectrum. Isotopically labeled ETU was used as an internal standard for quantitation and determination of recoveries. No enhancement of molecular ion signal intensity from unlabeled ETU was observed upon coelution with the isotopically labeled variant. This MS method permits detection of ETU with increased selectivity without compromising sensitivity.     

Packed column supercritical fluid chromatography/mass spectrometry for high-throughput analysis. Part 2

A supercritical fluid chromatograph was previously interfaced to a mass spectrometer (SFC/MS) and the system evaluated for applications requiring high sample throughput using negative-mode atmospheric-pressure chemical ionization (APCI) (Ventura et al. Anal. Chem. 1999, 71, 2410-2416). This report extends the previous work demonstrating the effectiveness of SFC/MS, using positive ion APCI for the analysis of compounds with a wide range of polarities. Substituting SFC/MS for LC/MS results in substantial time saving, increased chromatographic efficiency, and more precise quantitation of sample mixtures. Flow injection analysis (FIA) also benefits from our SFC/MS system. A broader range of solvents is compatible with the SFC mobile phase compared with LC/MS, and solutes elute more rapidly from the SFC/MS system, reducing sample carryover and cycle time. Our instrumental setup also allows for facile conversion between LC/MS and SFC/MS modes of operation.     

Development and evaluation of a candidate reference method for the determination of total cortisol in human serum using isotope dilution liquid chromatography/mass spectrometry and liquid chromatography/tandem mass spectrometry

Cortisol is an important diagnostic marker for the production of steroid hormones, and accurate measurements of serum cortisol are necessary for proper diagnosis of adrenal function. A candidate reference method involving isotope dilution coupled with liquid chromatography/mass spectrometry (LC/MS) and liquid chromatography/tandem mass spectrometry (LC/MS/MS) has been developed and critically evaluated. An isotopically labeled internal standard, cortisol-d(3), was added to serum, followed by equilibration and solid-phase and ethyl acetate extractions to prepare samples for liquid chromatography/mass spectrometry electrospray ionization (LC/MS-ESI) and liquid chromatography/tandem mass spectrometry electrospray ionization (LC/MS/MS-ESI) analyses. (M + H)(+) ions at m/z 363 and 366 for cortisol and its labeled internal standard were monitored for LC/MS. The transitions of (M + H)(+) --> [(M + H)(+) - 2H(2)O] at m/z 363 --> 327 and 366 --> 330 were monitored for LC/MS/MS. The accuracy of the measurement was evaluated by a comparison of results of this candidate reference method on lyophilized human serum reference materials for cortisol [Certified Reference Materials 192 and 193] with the certified values determined by gas chromatography/mass spectrometry reference methods and by a recovery study for the added cortisol. The results of this method for total cortisol agreed with the certified values within 1.1%. The recovery of the added cortisol ranged from 99.8% to 101.0%. This method was applied to the determination of cortisol in samples of frozen serum pools. Excellent precision was obtained with within-set CVs of 0.3%-1.5% and between-set CVs of 0.04%-0.4% for both LC/MS and LC/MS/MS analyses. The correlation coefficients of all linear regression lines ranged from 0.998 to 1.000. The detection limits (at a signal-to-noise ratio of approximately 3-5) were 10 and 15 pg for LC/MS and LC/MS/MS, respectively. This method, which demonstrates good accuracy and precision, and is free from interferences from structural analogues, qualifies as a candidate reference method and can be used as an alternative reference method to provide an accuracy base to which the routine methods can be compared.     

Integration of knowledge-based metabolic predictions with liquid chromatography data-dependent tandem mass spectrometry for drug metabolism studies: application to studies on the biotransformation of indinavir

Despite recent advances in the application of data-dependent liquid chromatography/tandem mass spectrometry (LC/MS/MS) to the identification of drug metabolites in complex biological matrixes, a prior knowledge of the likely routes of biotransformation of the therapeutic agent of interest greatly facilitates the detection and structural characterization of its metabolites. Thus, prediction of the [M + H]+ m/z values of expected metabolites allows for the construction of user-defined MS(n) protocols that frequently reveal the presence of minor drug metabolites, even in the presence of a vast excess of coeluting endogenous constituents. However, this approach suffers from inherent user bias, as a result of which additional "survey scans" (e.g., precursor ion and constant neutral loss scans) are required to ensure detection of as many drug-related components in the sample as possible. In the present study, a novel approach to this problem has been evaluated, in which knowledge-based predictions of metabolic pathways are first derived from a commercial database, the output from which is used to formulate a list-dependent LC/MS(n) data acquisition protocol. Using indinavir as a model drug, a substructure similarity search on the MDL metabolism database with a similarity index of 60% yielded 188 "hits", pointing to the possible operation of two hydrolytic, two N-dealkylation, three N-glucuronidation, one N-methylation, and several aromatic and aliphatic oxidation pathways. Integration of this information with data-dependent LC/MS(n) analysis using an ion trap mass spectrometer led to the identification of 18 metabolites of indinavir following incubation of the drug with human hepatic postmitochondrial preparations. This result was accomplished with only a single LC/MS(n) run, representing significant savings in instrument use and operator time, and afforded an accurate view of the complex in vitro metabolic profile of this drug.     

MALDI-FTICR imaging mass spectrometry of drugs and metabolites in tissue

A new approach is described for imaging mass spectrometry analysis of drugs and metabolites in tissue using matrix-assisted laser desorption ionization-Fourier transform ion cyclotron resonance (MALDI-FTICR). The technique utilizes the high resolving power to produce images from thousands of ions measured during a single mass spectrometry (MS)-mode experiment. Accurate mass measurement provides molecular specificity for the ion images on the basis of elemental composition. Final structural confirmation of the targeted compound is made from accurate mass fragment ions generated in an external quadrupole-collision cell. The ability to image many small molecules in a single measurement with high specificity is a significant improvement over existing MS/MS based technologies. Example images are shown for olanzapine in kidney and liver and imatinib in glioma.     

Solid-phase microextraction liquid chromatography/tandem mass spectrometry to determine postharvest fungicides in fruits

A method to determine five postharvest fungicides (dichloran, flutriafol, o-phenylphenol, prochloraz, tolclofos methyl) in fruits (cherries, lemons, oranges, peaches) has been developed using solid-phase microextraction (SPME) coupled to liquid chromatography (LC) with photodiode array (DAD), mass spectrometry (MS), or tandem mass spectrometry (MS/MS) with ion trap detection. Extraction involved sample homogenization with an acetone/water solution (5:1), filtration, and acetone evaporation prior to fiber extraction. The pesticides were isolated with a fused-silica fiber coated with 50-microm Carbowax/template resin. The effects of pH, ion strength, sample volume, and extraction time were investigated, and their impact on the SPME-LC/MS was studied. Dynamic and static modes of desorption were compared and the variables affecting desorption processes in SPME-LC optimized. Static desorption provided the best recoveries and peak shapes. Recoveries at the limit of quantification (LOQ) levels were between 10% for prochloraz and 60% for o-phenylphenol, with relative standard deviations from 13.6% for prochloraz to 3.1% for o-phenylphenol. The versatility of the method was also exhibited by its excellent linearity in the concentration intervals between 0.0005 and 5 mg kg(-1) for dichloran and 0.01-10 mg kg(-1) for tolclofos methyl and prochloraz. LOQs ranged from 0.25 to 1 microg g(-1) using DAD, from 0.002 to 0.01 microg g(-1) using LC/MS, and from 0.0005 to 0.01 to microg g(-1) using LC/MS/MS. LOQs obtained in the present study using LC/MS and LC/MS/MS are lower than maximum residue limits established for all the fungicides in any matrix studied. The method enables to determine polar pesticides at low-microgram per gram levels in fruits.     

Packed column supercritical fluid chromatography/mass spectrometry for high-throughput analysis

A supercritical fluid chromatograph was interfaced to a mass spectrometer, and the system was evaluated for applications requiring high sample throughput. Experiments presented demonstrate the high-speed separation capability of supercritical fluid chromatography (SFC) and the effectiveness of supercritical fluid chromatography/mass spectrometry (SFC/MS) for fast, accurate determinations of multicomponent mixtures. A high-throughput liquid chromatography/mass spectrometry (LC/MS) analysis cycle time is reduced 3-fold using our general SFC/MS high-throughput method, resulting in substantial time saving for large numbers of samples. Unknown mixture characterization is improved due to the increased selectivity of SFC/MS compared to LC/MS. This was demonstrated with sample mixtures from a 96-well combinatorial library plate. In this paper, we report a negative mode atmospheric pressure chemical ionization (APCI) method for SFC/MS suitable for most of the components in library production mixtures. Flow injection analysis (FIA) also benefits from this SFC/MS system. A broader range of solvents is amenable to the SFC mobile phase compared with standard LC/MS solvents, and solutes elute more rapidly from the SFC/MS system, reducing sample carryover and cycle time. Finally, our instrumental setup allows for facile conversion between LC/MS and SFC/MS modes of operation.     

Large scale pesticide multiresidue methods in food combining liquid chromatography--time-of-flight mass spectrometry and tandem mass spectrometry

Liquid chromatography tandem mass spectrometry (LC-MS/MS) and liquid chromatography time-of-flight mass spectrometry (LC-TOFMS) are powerful and complementary techniques that can independently cover the majority of the challenges related with pesticide residue food control. The sequential combination of both systems benefits from their complementary advantages and assists to increase the performance and to simplify routine large scale pesticide multiresidue methods. The proposed approach consists of three stages: (1) automated pesticide screening by LC-TOFMS; (2) identification by LC-TOFMS accurate mass measurements; and (3) confirmation and quantitation by LC-MS/MS. We have developed a fast comprehensive (identification/confirmation + quantitation) automated screening method for 100 target pesticides in crops. In the first stage, a set of data including m/z accurate mass windows (within 20 mDa width) and retention time is obtained (using a standard solution containing all the targeted pesticides) in order to build the automated screening procedure, which is created automatically by assigning retention time and the m/z mass window for each target pesticide. Samples are then analyzed, and the method enables the screening and preliminary identification of the species first by retention time and m/z mass window, followed by subsequent identification (only if positive results) by LC-TOFMS accurate mass measurements. After that, final confirmation of the positive findings using two MRM transitions and accurate quantitation is performed by LC-MS/MS using a hybrid triple quadrupole linear ion trap (QqLIT) mass spectrometer. In addition, the use of this QqLIT instrument also offers additional advantageous scanning modes (enhanced product ion and MS3 modes) for confirmatory purposes in compounds with poor fragmentation. Examples of applications to real samples show the potential of the proposed approach, including the detection of nonselected "a priori" compounds as a typical case of retrospective evaluation of banned or misused substances.     

High-throughput liquid chromatography/mass spectrometry method for the determination of the chromatographic hydrophobicity index

A fast gradient reversed-phase liquid chromatography (LC) method, using an acetonitrile gradient was developed to determine the chromatographic hydrophobicity index (CHI), as reported by Valco et al. (Anal. Chem. 1997, 69, 2022-2029).The analytical method provides retention times, based on UV detection at two different wavelengths, which then are converted into CHI values after calibration with a set of test compounds. The CHI of each compound is measured at three different pH values, 2.0, 7.4, and 10.5; so using an 8-min gradient at each pH value one compound can be analyzed in approximately 24 min. The aim of this work is to improve the throughput of the CHI screening using a LC/MS approach, so the application of the LC/MS technique is an extension of the LC/UV approach previously reported by Valco et al. This approach allows contemporary injection of N compounds into the LC/MS system, the retention time of each compound can be then extracted from the selected ion recording chromatograms. The throughput of the existing screening method could be increased by N times, where N is the number of compounds injected, so only three runs are needed to determine the CHI at three different pH values for a set of N compounds. The highest value of N depends on the total number of channels that can be monitored simultaneously; in the present work, 32 channels were used. This LC/MS method has been tested for a number of commercial products analyzed as mixtures, and data obtained were compared with those coming from the classical LC/UV approach. In the same way, the method was tested for a number of compounds associated with two GlaxoWellcome projects in the antibacterial area. Data reported show that the LC/MS method can be successfully applied for analyzing compounds in mixtures and for compounds with poor UW absorption, which cannot be analyzed with the standard LC/UV method.     

Intramolecular isobaric fragmentation: a curiosity of accurate mass analysis of sulfadimethoxine in pond water

Liquid chromatography with time-of-flight mass spectrometry (TOF-MS) and quadrupole-time-of-flight (Q-TOF) mass spectrometry/mass spectrometry (MS/MS) were used for the accurate mass analysis of sulfadimethoxine in pond water of a fish hatchery. Sulfadimethoxine is the most important sulfa antimicrobial used in aquaculture to treat bacterial disease in a wide variety of fish. Because correct identification is essential to environmental monitoring of antimicrobial pharmaceuticals, accurate mass analyses (TOF and Q-TOF-MS/MS) were compared to nominal mass measurement (quadrupole ion trap). It was known that all six members of the sulfa antimicrobial family gave a common 6-sulfanilamido ion at a nominal mass of m/z 156; thus, this ion was the focus of TOF confirmation (exact mass 156.0119 u) along with the protonated molecule (exact mass 311.0814 u). In the process of accurate mass confirmation of the 156 m/z fragment ion, a second isobaric ion (exact mass m/z 156.0773), was discovered at the same nominal mass, which was not differentiated by quadrupole ion trap. The structure was assigned as 2-4-dimethoxypyridine and is exactly the other protonated half of the sulfadimethoxine molecule. This discovery led to the subsequent use of Q-TOF-MS/MS and high-resolution identification of five other important ion fragments for the identification of sulfadimethoxine in pond water at environmental concentrations. The caveats of using low-resolution mass spectrometry without MS/MS for environmental monitoring are discussed in the light of high profile monitoring of sulfa antimicrobial pharmaceuticals in the aquatic environment.     

Primary structure determination of peptides and enzymatically digested proteins using capillary liquid chromatography/mass spectrometry and rapid linked-scan techniques

Primary protein sequences were determined for both peptides and enzymatically digested proteins by rapid linked-scan (B/E) liquid chromatography/mass spectrometry/mass spectrometry (LC/MS/MS) at the low-picomole level (10-50 pmol). During the course of a single LC/MS/MS analysis, we demonstrated that it is possible to generate interpretable collision-induced dissociation spectra of the eluting proteolytic peptides. Molecular weights of tryptic peptides were established by using 1/10 of the protein digest by operating in the capillary LC/frit-FABMS mode. Peptides exhibiting the strongest MH+ ions were then selected for subsequent LC/MS/MS analysis (typically 1/5 of the remaining protein digest). Elution times for each chromatographic peak were generally greater than 30 s. It was therefore possible to obtain a minimum of six B/E fast linked-scan spectra during the course of elution of each peptide component. Typically, B/E linked scans of the greatest ion abundance (obtained at the chromatographic peak maximum) were averaged to enhance the signal/noise ratio at these low-picomole levels. Unit resolution was observed for product ions below m/z 1000. Rapid linked scanning by LC/frit-FABMS/MS provided mass assignments for product ions within 0.2-0.3 amu of theoretical values. Side-chain fragment ions (wn and dn) were also observed, which allowed for the differentiation of isobaric amino acids (e.g., leucine and isoleucine). Examples of the application of this fast linked-scan technique to LC/MS/MS are presented for complex mixtures of unknown peptides and the tryptic digestion of phosphorylated beta-casein.     

Comprehensive profiling of free and conjugated estrogens by capillary electrophoresis-time of flight/mass spectrometry

The biological activity of estrogens is tightly regulated by regioselective phase I/II metabolic transformations that are critical to human health. Current methods for analysis of urinary estrogens are limited by complicated sample pretreatment and/or inadequate specificity for free estrogens and their glucuronide/sulfate conjugates that vary widely in their intrinsic polarity. In this work, direct speciation of intact estrogen conjugates and their regioisomers is demonstrated using capillary electrophoresis-time-of-flight/mass spectrometry (CE-TOF/MS) when using an alkaline buffer system with negative ion mode detection. This method allows for resolution of weakly acidic native estrogens, anionic estrogen conjugates and their positional isomers without significant matrix-induced ion suppression effects in human urine. Identification of unknown estrogen metabolites using CE-TOF/MS is supported by accurate mass together with their characteristic relative migration times, which can be predicted based on two intrinsic physicochemical properties of an ion. CE-TOF/MS offers a promising strategy for comprehensive profiling of estrogens and other classes of steroid conjugates that is needed for deeper insight into the etiology and treatment of chronic disorders associated with impaired estrogen metabolism.     

Selective determination of aromatic sulfonates in landfill leachates and groundwater using microbore liquid chromatography coupled with mass spectrometry

Aromatic sulfonates (AS) are large-volume chemicals used in many technical processes of, for instance, the textile industry or construction. A LC/MS method for the selective determination of AS in environmental samples, based on a single-quadrupole MS, was developed and validated. The central point of this technique is the use of the compound-specific fragment ion SO3.- as marker for aromatic sulfonates. This negatively charged SO3 radical, together with the fact that AS undergo loss of SO2, allows screening for AS in complex matrixes, even in the presence of sulfate anions. Calibration curves generated from LC/MS data showed good linearity over 3 orders of magnitude, with an absolute limit of detection of approximately 1 ng. The relative standard deviation for mean areas obtained from reconstructed ion chromatograms ranged from 2.9 to 8.6%. Unlike UV detection, this LC/MS method gives similar response for both naphthalene- and benzene-sulfonates. The method presented was successfully applied to landfill leachates and groundwater, downstream of a landfill. Furthermore, this technique allowed identification of an unknown AS found in drain samples.