Bi2O3 Vaporization in Microwave-Sintered ZnO Varistors

Vaporization of Bi₂O₃ in microwave-sintered ZnO varistors is discussed in this study. The Bi₂O₃ vaporization of ZnO varistors sintered by a conventional electric furnace is also studied for comparison. The results show that the Bi₂O₃ vaporization in microwave-sintered ZnO varistors is more homogenous from the surface to the inside of the sample, which results from the special thermal gradient inside the microwave-sintered samples, and we also find out that the Bi₂O₃ vaporization directly affects the electrical properties of ZnO varistors. Microwave-sintered samples exhibit more excellent electrical properties than the conventional ones because the homogenous Bi₂O₃ vaporization leads to more uniform microstructures.     

Grain Growth of ZnO during Bi2O3 Liquid-Phase Sintering

Grain growth of ZnO during the liquid-phase sintering of binary ZnO–Bi₂O₃ ceramics has been studied for Bi₂O₃ contents from 3 to 12 wt% and sintering from 900° to 1400°C. The results are considered in combination with previously published studies of ZnO grain growth in the ZnO–Bi₂O₃ system. For the Bi₂O₃ contents of the present study, the rate of ZnO grain growth is found to decrease with increasing Bi₂O₃. Activation analysis, when combined with the results of similar analyses of the previous studies, reveals a change in the rate-controlling mechanism for ZnO grain growth. Following a low-Bi₂O₃-content region of nearly constant activation energy values of about 150 kJ/mol, further Bi₂O₃ additions cause an increase of the activation energy to about 270 kJ/mol. consistent with accepted models of liquid-phase sintering, it is concluded that the rate-controlling mechanism of ZnO grain growth during liquid-phase sintering in the presence of Bi₂O₃ changes from one of a phase-boundary reaction at low Bi₂O₃ levels to one of diffusion through the liquid phase at about the 5 to 6 wt% Bi₂O₃ level and above.     

Microstructure of Varistors Prepared with Zinc Oxide Nanoparticles Coated with Bi2O3

Zinc oxide (ZnO) nanoparticles coated with 1–5 wt% Bi₂O₃ were prepared by precipitating a Bi(NO₃)₃ solution onto a ZnO precursor. Transmission electron microscopy showed that a homogeneous Bi₂O₃ layer coated the surface of the ZnO nanoparticles and that the ZnO particle size was ∼30–50 nm. Scanning electron microscopy showed that ZnO grains sintered at 1150°C were homogeneous in size and surrounded by a uniform Bi₂O₃ layer. When the ZnO grains were surrounded fully by Bi₂O₃ liquid phases, further increases in the ZnO grain size were not affected by the Bi₂O₃ content. This predesigned ZnO nanoparticle structure was shown to promote homogeneous ZnO grains with perfect crystal growth.     

Transformational Plasticity in Bi2O3

Transformational plasticity associated with the monoclinic-to-cubic phase transition at 730°C in Bi₂O₃ was observed and characterized. This phenomenon is explained in terms of Greenwood and Johnson's model of internal stress-induced deformation, proceeding, in this instance, by a time-dependent, grain-size-sensitive creep mechanism, probably grain-boundary sliding. Criteria are proposed for choosing other prospective transformationally plastic ceramics; they are met by Bi₂WO₆, which also exhibits extensive transformation plasticity.     

Grain Growth Behavior of Bi2O3-Doped ZnO Grains in a Multilayer Varistor

A novel bismuth-doped zinc oxide (ZnO) laminated structure is prepared in the present study. Seven layers with thickness ranging from 20 to 140 μm are laminated together with platinum (Pt) inner electrodes. The growth of Bi₂O₃-doped ZnO grains within a very limited space between Pt electrodes is investigated. The grain growth behavior outside the confinement of electrodes is also studied for comparison purposes. At the beginning of sintering, a similar grain growth behavior is observed at different locations of the laminated structure. However, as sintering proceeds, the rate of grain growth within the Pt inner electrodes is decreased because of the decrease of available transportation paths. The grains between the electrodes then develop into a columnar shape as they make contact with the electrodes above and below them. Both the grain size and its distribution decrease with decreasing layer thickness.     

Grain Growth of ZnO in ZnO-Bl2O3 Ceramics with Ai2O3 Additions

Grain growth of ZnO during liquid-phase sintering of a ZnO-6 wt% Bi₂O₃ ceramic was investigated for A1₂O₃ additions from 0.10 to 0.80 wt%. Sintering in air for 0.5 to 4 h at 900° to 1400°C was studied. The AI₂O₃ reacted with the ZnO to form ZnAl₂O₄ spinel, which reduced the rate of ZnO grain growth. The ZnO grain-growth exponent was determined to be 4 and the activation energy for ZnO grain growth was estimated to be 400 kJ/mol. These values were compared with the activation parameters for ZnO grain growth in other ceramic systems. It was confirmed that the reduced ZnO grain growth was a result of ZnAl₂O₄ spinel particles pinning the ZnO grain boundaries and reducing their mobility, which explained the grain-growth exponent of 4. It was concluded that the 400 kJ/mol activation energy was related to the transport of the ZnAl₂O₄ spinel particles, most probably controlled by the diffusion of O^2- in the ZnAl₂O₄ spinel structure.     

Kinetics of Solid-State Reaction of Bi2O3 and Fe2O3

Solid-state reactions of equimolar mixtures of Bi₂O₃ and Fe₂O₃ from 625° to 830°C and their kinetics were investigated. The reaction rates were determined from the integrated X-ray diffraction intensities of the strongest peaks of the reactants and products. The activation energy for the formation of BiFeO₃ was 96.6±9.0 kcal/mol; that for a second-phase compound, Bi₂Fe₄O₉, which formed above 675°C, was 99.4±9.0 kcal/mol. Specific rate constants for these simultaneous reactions were obtained. The preparation of single-phase BiFeO₃ from the stoichiometric mixture of Bi₂O₃ and Fe₂O₃ is discussed.     

Differences in Wetting Characteristics of Bi2O3 Polymorphs in ZnO Varistor Materials

Detailed analysis of the microstructure of grain boundaries, especially triple-grain and multiple-grain junctions, in ZnO varistor materials has been performed using transmission electron microscopy. Different polymorphs of Bi₂O₃ are shown to exhibit different wetting properties on ZnO interfaces. Recent investigations suggest that the equilibrium configuration consists of crystalline Bi₂O₃ in the triple-grain and multiple-grain junctions and an amorphous bismuth-rich film in the ZnO/ZnO grain boundaries. The present investigation supports this suggestion for δ-Bi₂O₃ and also adds to the microstructural image and wetting properties of α-Bi₂O₃.     

The System Bi2O3-SiO2

The Bi₂O₃-rich side of the system Bi₂O₃-SiO₂ was studied with powder X-ray diffraction and differential thermal analysis. In the composition 6Bi₂O₃. x SiO₂, the metastable γ phase (bcc) was observed to exist over the range of 0 < x ≤ 1. In most of the compositions studied, metastable phases of water-quenched melts transformed into another metastable phase before reaching stable phases. A modification of the phase diagram is proposed.     

Liquid-Phase Sintering of MgO–Bi2O3

Liquid-phase sintering of MgO-5 wt% Bi₂O₃ was studied by loading dilatometry. The ratio of the creep viscosity to the densification viscosity (∼1.8) and the sintering stress remained nearly constant in a wide density interval. These results, together with results on several other systems, indicate that the constancy of the sintering stress during densification may be a general phenomenon, regardless of densification mechanism.     

Transformational Superplasticity in the Bi2O3-Sm2O3 Eutectoid System

Transformational superplasticity associated with the eutectoid reaction in the Bi₂O₃-Sm₂O₃ system was observed and characterized in hypoeutectoid and hypereutectoid compositions. Transformational strain varied linearly with applied stress and exhibited a stress-axis intercept, or threshold stress, that is related to the proeutectoid microconstituent. Results are explained quantitatively using the analysis by Greenwood and Johnson and a creep mechanism.     

Grain Growth in Sintered ZnO and ZnO-Bi2O3 Ceramics

Grain growth in a high-purity ZnO and for the same ZnO with Bi₂O₃ additions from 0.5 to 4 wt% was studied for sintering from 900° to 1400°C in air. The results are discussed and compared with previous studies in terms of the phenomenological kinetic grain growth expression: G ⁿ— G ⁿ₀= K ₀ t exp(— Q/RT ). For the pure ZnO, the grain growth exponent or n value was observed to be 3 while the apparent activation energy was 224 ± 16 kJ/mol. These parameters substantiate the Gupta and Coble conclusion of a Zn²⁺ lattice diffusion mechanism. Additions of Bi₂O₃ to promote liquidphase sintering increased the ZnO grain size and the grain growth exponent to about 5, but reduced the apparent activation energy to about 150 kJ/mol, independent of Bi₂O₃ content. The preexponential term K ₀ was also independent of Bi₂O₃ content. It is concluded that the grain growth of ZnO in liquid-phase-sintered ZnO-Bi₂O₃ ceramics is controlled by the phase boundary reaction of the solid ZnO grains and the Bi₂O₃-rich liquid phase.     

Effects of Excess Bi2O3 on the Ferroelectric Behavior of Nd-Doped Bi4Ti3O12 Thin Films

Effects of excess Bi₂O₃ content on formation of (Bi_3.15Nd_0.85)Ti₃O₁₂ (BNT) films deposited by RF sputtering were investigated. The microstructures and electrical properties of BNT thin films are strongly dependent on the excess Bi₂O₃ content and post-sputtering annealing temperature, as examined by XRD, SEM, and P – E hysteresis loops. A small amount of excess bismuth improves the crystallinity and therefore polarization of BNT films, while too much excess bismuth leads to a reduction in polarization and an increase in coercive field. P – E loops of well-established squareness were observed for the BNT films derived from a moderate amount of Bi₂O₃ excess (5 mol%), where a remanent polarization 2P _r of 25.2 μC/cm² and 2E _c of 161.5 kV/cm were shown. A similar change in dielectric constant with increasing excess Bi₂O₃ content was also observed, with the highest dielectric constant of 304.1 being measured for the BNT film derived from 5 mol% excess Bi₂O₃.     

Cubic-to-Tetragonal Displacive Transformation in Gd2O3–Bi2O3 Ceramics

Gd₂O₃-doped Bi₂O₃ polycrystalline ceramics containing between 2 and 7 mol% Gd₂O₃ were fabricated by pressureless sintering powder compacts. The as-sintered samples were tetragonal at room temperature. Hightemperature X-ray diffraction (XRD) traces showed that the samples were cubic at elevated temperatures and transformed into the tetragonal polymorph during cooling. On the basis of conductivity measurements as a function of temperature and differential scanning calorimetry (DSC), the cubic → tetragonal as well as tetragonal → cubic → teansition temperatures were determined as a function of Gd₂O₃ concentration. The cubic → tetragonal transformation appears to be a displacive transformation. It was observed that additions of ZrO₂ as a dopant, which is known to suppress cation interdiffusion in rare-earth oxide–Bi₂O₃ systems, did not suppress the transition, consistent with it being a displacive transition. Annealing of samples at temperatures 660°C for several hundred hours led to decomposition into a mixture of monoclinic and rhombohedral phases. This shows that the tetragonal polymorph is a metastable phase.     

Origin of Solid-State Activated Sintering in Bi2O3-Doped ZnO

Activated sintering in Bi₂O₃-doped ZnO has been studied with emphasis on the mechanistic role of intergranular amorphous films. The atomic-level microstructures and bismuth solute distributions in doped powders have been investigated using high-resolution electron microscopy and scanning transmission electron microscopy. Densification is observed to be significant below the bulk eutectic temperature in the presence of Bi₂O₃ concentrations as low as 0.58 mol%. Transmission electron microscopy of as-calcined and sintered powders shows that significant neck growth and particle coarsening occur in the solid state. Intergranular amorphous films of ∼1 nm thickness, terminating in wetting menisci at sinter-necks, are observed to form concurrently with the onset of activated sintering. In a few instances, amorphous films are also observed at surfaces of the ZnO particles. These films appear to be the free-surface counterpart to equilibrium-thickness intergranular films. Activated sintering in this binary system is attributed to rapid mass transport through subeutectic, equilibrium-thickness intergranular films, with the amorphous phase also providing capillary pressure.     

Nature of Intergranular Phase in Nonohmic ZnO Ceramics Containing 0.5 Mol% Bi2O3

The intergranular phase obtained by sintering a binary mixture of ZnO + 0.5 mol% Bi₂O₃ was isolated by using a dilute solution of HCIO₄, which etches ZnO preferentially. The combined results of selected-area electron diffraction and microscopy, microprobe analysis, and X-ray diffraction strongly indicate that the intergranular material is a polycrystalline phase of tetragonal β-Bi₂O₃ ( P 42₁ c ), rather than the amorphous ZnO-Bi₂O₃ phase reported earlier. It appears that the nonohmic behavior in this prototype metal-oxide varistor must be an interfacial property associated with the semiconducting ZnO grains separated by thin layers of high-resistivity Bi₂O₃.