加拿大油砂溶剂抽提分离工艺的研究

对加拿大油砂进行了溶剂抽提分离试验,考察了石油醚、石脑油、甲苯、环己烷以及重整汽油对提取效果的影响,确定重整汽油为最佳抽提溶剂.综合考察了提取温度、溶剂与油砂体积比、提取时间以及搅拌速度等工艺操作条件对油砂沥青提取的影响,结果表明,在提取温度500℃,溶剂和油砂的体积比为1∶1,提取时间60 min,搅拌速度为80 r/min的条件下,油砂沥青提取率达到92.57%.     

克拉玛依油砂溶剂萃取分离实验研究

以克拉玛依油砂为实验对象,考察石油醚、环己烷、正戊烷、正庚烷、甲苯、CS2及复合溶剂EOSA萃取分离油砂沥青的效果,确定EOSA为最佳萃取溶剂。研究了温度、溶剂用量、时间对EOSA萃取分离油砂沥青收率的影响。结果表明,在萃取温度30℃、剂砂比2 mL/g条件下萃取30 min,油砂沥青的收率可达95%以上。再生实验结果表明,在60~80℃条件下,溶剂回收率超过99%。该工艺具有无水参与、零排放、低能耗、高收率等优点。     

油砂沥青溶剂提取回收组合工艺

采用有机溶剂提取-超临界CO2回收溶剂这一组合方法对加拿大Athabasca油砂进行了提取分离及溶剂回收实验,通过实验筛选出最佳抽提溶剂为重整汽油。溶剂提取的最佳工艺条件:提取温度80℃,溶剂流量60mL/min,提取时间60min。在此条件下油砂沥青提取率达到92.74%。对超临界CO2-重整汽油体系的相行为进行研究,并通过实验综合考察了温度、压力、CO2流量以及回收时间等工艺操作条件对溶剂回收的影响。结果表明:在回收温度50℃,回收压力13MPa,溶剂与CO2分离温度70℃,压力5MPa,CO2流量7.5L/h,时间1h的条件下,重整汽油的回收率为98.71%。     

溶剂提取SZ36-1模拟油砂油的实验研究

用溶剂提取法处理SZ36-1模拟油砂,优选120#溶剂油为适宜提取溶剂,确定260 nm为测定原油含量的最佳紫外可见吸收波长。考察了提取温度、提取次数、剂砂质量比、抽提时间等条件对模拟油砂处理的影响。结果表明,在剂砂质量比10∶1,75℃下提取40 min,重复提取3次的条件下,油砂油提取率达95%以上,尾砂含油量低于0.35%。原油提取效果好、清除彻底,为120#溶剂油提取油砂油、检验SZ36-1油砂污染程度提供了依据。     

油砂油泥含油率测定方法研究

以中国内蒙扎赉特旗油砂为例,利用有机溶剂抽提的方法测定油砂含油率,并通过实验及抽提溶剂的性质等确定了最佳实验操作条件.实验结果表明:选用120#溶剂油为抽提试剂,在抽提温度为115℃、抽提时间为3.5 h的条件下,可有效的把油砂油从油砂中抽提出来,从而根据重量法测得油砂油含率.该方法同时可适用于对油泥油含率的测定.     

印尼特细油砂的基本性质和加工路线研究

印尼特细油砂是一种原产于印度尼西亚的稠油资源,常见有黄色和黑色两种。通过甲苯溶剂抽提法和减压蒸馏法可得到油砂沥青和细砂粒,得到的油砂沥青和砂粒用于油砂基本性质的测定。并简单探讨了该油砂适宜的加工路线。印尼油砂具有含油率高,含硫量高的特点,并且适合采用热解法进行后续加工成轻质油。     

新疆油砂水洗分离提油工艺研究

以新疆风砂16#油砂为测试样品进行油砂水洗分离影响因素的分析.实验综合考察了加热温度、分离试剂质量分数、加热时间、剂砂质量比等因素对油砂分离的影响.通过正交实验得出油砂水洗分离的最佳工艺操作条件为:分离温度90℃、ω(分离剂)=5%、分离时间20 min、剂砂质量比为2:1,追加实验结果表明在此操作条件下,油砂出油率最高可达94%以上.分离残砂经两次清洗后砂中含油丰<1%、pH值<8、砂中试剂总质量分数≤0.7%,达到排放标准,对环境无污染.     

水剂空气化分离油砂的研究

在实验室条件下,使用自制分离器及浆化剂进行油砂分离试验,并通入空气来提高油砂分离效果。实验中主要考察了浆化剂量、浆化时间、浆化温度及通气量对油砂分离效果的影响。得出了水剂空气化分离油砂的最适宜操作条件: 剂砂比0．24:1,浆化温度60～65℃,浆化时间50min,通气量0．5 m3／h。而使用的水剂无毒,无腐蚀,价廉易得。该工艺操作简单,具有实用价值。     

水辅助溶剂法提取油砂中的沥青

开发了一种水辅助溶剂法从油砂中提取沥青的技术。该方法通过在油砂固相与有机溶剂间介入水层提取油砂中的沥青。以内蒙古扎赉特旗油砂矿为研究对象,考察了温度、剂砂质量比、提取时间、甲苯在复合溶剂中的含量及溶剂的种类与性质对沥青回收率高低的影响,结果表明：最佳提取条件为提取温度50℃,剂砂质量比1∶1,提取时间25min。沥青回收率与提取溶剂的性质紧密相关,水层介入有效降低了固体微粒组分在有机相中的含量,且便于后续的有机相与泥砂相的分离。通过对各种溶剂提取的沥青进行组分分析,发现各种溶剂对沥青提取能力的差异性源于溶剂的化学组成和结构不同。本文相关研究结果对溶剂法提取油砂中沥青技术及溶剂种类的选择具有指导作用。     

不同有机溶剂对新疆油砂沥青的组成性质影响

油砂作为一种非常规石油资源,越来越受到人们的重视。油砂沥青的含量和性质对其开发有着重要的影响。有机溶剂抽提可以测定油砂沥青的含量。本文研究了3种溶剂对新疆油砂的抽提能力,并对不同溶剂抽提得到的新疆油砂沥青进行了性质分析。结果表明,新疆油砂含油率（甲苯测）为11.75%,属于中品位油砂矿;甲苯、氯仿和石油醚3种不同溶剂对新疆油砂沥青进行抽提,发现3种溶剂抽提能力的大小关系为氯仿＞甲苯＞石油醚;抽提过程中,氯仿表现出对胶质和沥青质较强的萃取能力,而石油醚对沥青质的萃取能力几乎为0,采用氯仿可以更准确地测定油砂沥青的含量。氯仿抽提得到新疆油砂沥青及其组分的杂原子含量和分子量高于甲苯和石油醚抽提的。由红外谱图发现,氯仿抽提得到的油砂沥青的含氧、含硫官能团的吸收峰强度大于甲苯和石油醚抽提的,表明氯仿对油砂沥青中极性物质的抽提能力更强。     

油砂沥青分离技术研究进展

油砂作为一种储量丰富的非常规石油资源,越来越受到世界各国的广泛关注。对于油砂的加工利用,其前提就是油砂沥青的分离,因此对其技术的研究十分必要。本文首先介绍了油砂的组成及分类,然后着重对几种主要油砂分离技术（热水洗法、有机溶剂萃取法、超临界流体萃取法、超声波辅助萃取法、离子液体萃取法和热解干馏法）的优缺点进行了汇总,并详细分析了它们各自的分离流程。其中,热水洗法、有机溶剂萃取法和热解干馏法是目前研究相对成熟的3种方法,而其他方法虽然分离效果相对高,但是对工艺条件和设备的要求较高,导致较高的投资和运行成本,因此还需要对这些油砂沥青分离工艺进行更加深入的研究,以满足工业化应用的要求。最后,对油砂沥青分离技术的发展前景进行了展望。     

油砂沥青超声波减粘工艺研究

油砂沥青粘度较大,自然状态下不易流动,严重影响了管道输送及加工,针对目前油砂沥青研究中存在的问题,采用超声波进行了减粘的实验研究。实验综合考察了超声波作用时间、温度、超声波频率、超声波功率等因素对减粘效果的影响。实验结果表明,在适当的超声作用时间(20 min)、适宜的温度(30℃)、适宜的超声波频率(20 kHz)和超声波功率(250 W)的条件下,油砂沥青的减粘率可达80%以上。经超声波处理后的油砂沥青粘度略有恢复,但仍远低于处理前的粘度,超声波减粘效果良好。     

Prediction of bitumen content in oil sand based on FT-IR measurement

FT-IR spectra of bitumen are utilized to propose simple prediction method of bitumen content in oil sand. Analysis and fractionation of Athabasca oil sand were carried out by standard method. A fraction of bitumen dissolved in tetrahydrofuran (THF) was 9.1 wt% and insoluble fraction was found as concomitantly clean clay (sand). The asphaltene fraction of oil sand was 1.42 wt%, which has higher sulfur content and lower H/C molar ratio than that of maltene. The clean clay and bitumen were used to prepare clay/bitumen composites. FT-IR spectra of different clay/bitumen composite were measured and compared. From analysis of the absorbance data, the empirical equation to predict bitumen content in oil sand was acquired using linear least square fitting. Using this equation, bitumen content of Athabasca oil sand was predicted to have a value of 10.5 wt% which is similar to 9.1 wt% of bitumen content extracted by THF solvent from oil sand.     

Preparation of bitumen from oil sand by centrifugation

Centrifugation was shown to have certain advantages over solvent extraction for the separation of bitumen from oil sand for research purposes. No fractionation of the bitumen during centrifugation was detected by chemical analysis. Some limitations of the method are pointed out.     

Capillary Curves for Ex‐situ Washing of Oil‐Coated Particles

The oil removal efficiency for the ex situ extraction of bitumen from oil sands, or ex situ washing of oil‐contaminated sand and related processes is determined by the balance of forces at the oil/water and solid/fluid interfaces. The objective of this work is to estimate the balance of forces at the interface using dimensionless numbers, and their use in evaluating and engineering ex situ soil washing processes. To this end, bitumen was removed from bitumen‐coated sand particles using a two‐step process. In the first step, the particles were mixed with a suitable solvent (toluene) used, primarily, to reduce the viscosity of bitumen. The particles were then mixed with water or an aqueous surfactant solution capable of producing low interfacial tensions with the solvent‐bitumen mixture. The fraction of oil retained after washing was evaluated as a function of interfacial tension, solvent/bitumen ratio, mixing time, mixing velocity, and particle size. These ex situ washing conditions were normalized using dimensionless film and particle‐based Weber and Capillary numbers. The fraction of oil retained by the particles was plotted against these dimensionless numbers to generate capillary curves similar to those used in enhanced oil recovery. These curves reveal the existence of a critical film‐based Weber number and a particle‐based Capillary number that can be used in the design or evaluation of soil washing processes. The film‐based Weber number also explained literature data that associates interfacial tension with the removal of oil from oil‐based drill cuttings, as well as field observations on the role that particle size plays on the removal of oil in soil washing operations.     

Bitumen—sand interaction in oil sand processing

Bitumen—sand interaction was studied as a function of pH, particle size, temperature and solvent addition to bitumen. Sand particles can be easily detached from the bitumen surface at pH> 6. At pH < 6, strong attachment between bitumen and sand is observed. The bitumen—sand interaction is also particle-size dependent: the finer the particles, the stronger the attachment. The detachment of coarse particles from bitumen can be achieved by increasing the alkalinity of the solution, but not for fine particles, indicating that the particle size is one of the critical factors affecting liberation of bitumen from sand. Increasing temperature has two effects: it is not only reduces the viscosity to facilitate bitumen liberation, but also increases the electrostatic repulsion between sand and bitumen. This is confirmed by the DLVO theory and is in agreement with the batch extraction results on real oil sands.     

离子液体促进溶剂萃取油砂沥青

传统水洗法和溶剂萃取法萃取油砂沥青时,存在沥青中含有沙土和残沙中含有油等缺点。为解决上述缺点,本文采用不同比例的乙酸甲酯/正庚烷复合溶剂萃取油砂沥青,研究了离子液体（1-丁基-3-甲基咪唑四氟硼酸盐,[Emim]BF4）对该溶剂萃取体系的萃取率和分离洁净程度的影响。采用红外光谱仪和扫描电镜对萃取后的残沙和沥青的洁净程度进行了定性分析,并结合元素分析仪和电感耦合等离子体发射光谱仪获得萃取后残沙和沥青的洁净程度的定量结果。实验结果表明：当复合溶剂体积比为2∶3时,[Emim]BF4促使沥青回收率达到最大值94.20%,比单纯复合溶剂萃取体系的最大萃取率高7.92%;通过上述测试方法的定性和定量分析,证明了[Emim]BF4能有效解决沥青夹带沙土和残沙中含油的问题。     

Water‐Based Bitumen Recovery from Diluent‐Conditioned Oil Sands

Important process development aspects leading to more efficient bitumen recovery from diluent‐conditioned oil sands by water‐based methods are discussed. Bitumen viscosity of 0.5–2 Pa·s is required at the processing temperature and can be reduced to this level by bitumen dilution with an organic solvent. Oil sand porosity, however, poses a restriction on the amount of diluent that can be accepted by the oil sand. Also oil sand‐diluent conditioning time is an important process parameter and can vary from a few minutes for oil sands with low‐viscosity bitumen to several hours if viscosity of the bitumen is high. Additionally, the bitumen separation efficiency during digestion and flotation can be enhanced by reducing the bitumen/water interfacial tension through addition, for example, of tripolyphosphate to the aqueous phase.     

Clay minerals in nonaqueous extraction of bitumen from Alberta oil sands: Part 1. Nonaqueous extraction procedure

A non-aqueous bitumen extraction process was studied where only toluene and heptane, with no water additions, were used to extract bitumen from two Alberta oil sands ore samples. One sample had a high bitumen (13.5 wt.%) and low fines (5.3 wt.% < 45 μm) contents, while the other sample had an intermediate bitumen (10.5 wt.%) and high fines (23.3 wt.%) contents. Bitumen recovery and product quality were measured under different process conditions such as the ratio of toluene to heptane and settling time. The Dean Stark procedure was used to determine the solids, bitumen and water contents of the extraction products. In addition, the water content was determined by the Karl Fischer titration method. High bitumen recovery was obtained for both oil sands ore samples although the high fines ore sample was more sensitive to the extraction conditions, especially the toluene to heptane ratio. A product with high purity, containing more than 99.5 wt.% bitumen on a solvent-free basis, was produced at room temperature under the optimum extraction conditions tested. The optimum settling time to achieve a pure product was less than 10 min, based on solids and water contents in the supernatant.