纤维增强聚合物复合材料界面残余热应力研究进展

本文综述了聚合物基纤维复合材料界面残余应力的形成，测定方法和各种理论分析方法，阐述了界面残余应力对办面粘结强度以及复合材料断裂韧性和强度的影响，最后对界面残余应力的控制方法作了评述。     

芳纶纤维/AFR树脂复合材料界面粘结性能的研究

为了改善芳纶纤维复合材料的界面粘结性能,合成了一种新型树脂(AFR)作为基体,以未经任何表面处理的芳纶纤维作增强材料,制备了芳纶纤维/AFR复合材料。采用测定表面能、接触角、层间剪切强度、横向拉伸性能和扫描电镜观察形貌等方法,从宏观和微观等方面研究了芳纶纤维/AFR复合材料的界面粘结性能。结果表明,AFR树脂与芳纶纤维有相近的表面能,AFR树脂溶液与芳纶纤维的接触角为42.8°,而环氧树脂(EP)与芳纶纤维的接触角为68°,说明AFR树脂对芳纶纤维的润湿性优于EP树脂;芳纶/AFR复合材料的层间剪切强度、横向拉伸强度和纵向拉伸强度分别为74.64MPa、25.34MPa和2256MPa,比芳纶/EP复合材料的相应强度分别提高了28.7%、32.5%和13.4%,其复合材料破坏面的形貌也说明芳纶纤维与AFR树脂之间的界面粘结性能较好。     

纤维增强聚合物基复合材料界面残余热应力研究

本文综述了聚合物基纤维复合材料界面残余热应力的形成、测定方法和各种分析方法。阐述了残余就地界面粘结强度以及复合材料韧性和强度的影响。最后对界面残余应力的控制方法作了评述。     

表面处理对剑麻纤维性能及与淀粉相容性的影响

采用碱处理、硅烷偶联剂处理以及两者复合的处理方法对剑麻纤维进行表面改性,研究了不同处理方法对剑麻纤维的性能以及剑麻纤维/淀粉复合材料界面粘结性能的影响。通过傅立叶变换红外光谱仪、热重分析仪、扫描电子显微镜和万能试验机对不同处理的剑麻纤维进行表征,使用拔出实验测试剑麻/淀粉复合材料的界面粘结情况,并采用二参数威布尔模型计算拉伸强度和界面剪切强度。结果表明,所有处理方法都能提高剑麻纤维的热稳定性和界面剪切强度。与未处理纤维相比,碱处理后的剑麻纤维与淀粉的界面剪切强度最高,为2.011 MPa,提高了19%。     

复合材料飞轮研究进展

本文对比了复合材料飞轮转子与金属材料飞轮转子的性能,指出复合材料比强度高、密度小等特点使其可以使飞轮具有更高的极限转速和储能能力。同时指出了复合材料各向异性的特点使得其垂直纤维方向强度低,限制了飞轮的最高转速。介绍了目前复合材料飞轮主要采用单层圆环飞轮和多层圆环飞轮2种结构形式。同时指出采用柔性树脂基体,改善树脂和纤维的界面粘结状态和增强树脂本身的强度也是提高复合材料径向强度的有效途径。     

基于NOL环的高性能纤维与环氧树脂的匹配性研究

纤维与树脂的界面对复合材料的整体力学性能有着显著的影响。基于NOL环的宏观力学测试一般被用来反映复合材料的界面粘结性能,因此适用于评价纤维与树脂之间的宏观力学性能匹配性。为了探究高性能碳纤维T700SC、T800HB及高强玻璃纤维与环氧树脂的宏观力学性能匹配性,本研究首先根据GB/T 1458—2008国家标准制备NOL环试样,再借助NOL环的拉伸和层间剪切强度测试分析了高性能纤维与环氧树脂不同匹配组合宏观力学性能差异的原因,并寻找出最佳匹配组合。结果表明:玻璃纤维与环氧树脂的界面存在最佳的粘结强度,而且不同粘结强度导致拉伸强度和破坏机理不同,而碳纤维复合材料界面性能较差,容易分层破坏;T800HB与环氧树脂的宏观力学匹配性优于T700SC,环氧树脂力学性能、碳纤维的表面微观结构与性质以及环氧树脂与碳纤维之间的相互作用关系是影响界面粘结性能的根本原因。该研究在高性能纤维单向复合材料的材料选择与设计方面具有现实意义。     

不同龄期钢纤维增强水泥砂浆纤维拉拔试验与模拟研究

钢纤维增强水泥基复合材料作为一种多相复合材料,其增强增韧效果的发挥依赖于钢纤维与基体之间的界面粘结性能。通过开展不同龄期的钢纤维增强水泥基复合材料单根纤维拉拔试验及数值模拟研究,分析了龄期对钢纤维增强水泥砂浆界面粘结性能的影响,建立了不同龄期的单根纤维拉拔细观模型,通过将模拟结果与试验结果进行对比验证模型的有效性。根据所建立的细观模型分别对不同龄期钢纤维增强水泥砂浆纤维-基体间的界面粘结作用机理及纤维-基体间粘结表面在纤维拔出过程中的应力变化进行了分析。结果表明:所建立细观模型模拟得到的纤维最大拉拔力及荷载-滑移曲线与试验结果吻合较好,钢纤维的最大拉拔力及钢纤维-水泥砂浆基体的界面粘结强度均随着龄期的增加而增加;在7 d龄期内界面粘结强度的增长速度较快,7 d龄期后增长速度放缓;随着龄期的增加,不同龄期段的界面粘结强度的增长率逐渐减小并趋于稳定。采用拟合得到的粘结表面材料参数能够有效模拟各龄期下单根钢纤维从水泥砂浆中的拔出过程。     

芳纶纤维增强树脂基复合材料的界面粘结性能研究

为了改善芳纶纤维增强树脂基复合材料的界面粘结性能,从树脂基体入手,依据相似相容原理和芳纶的结构特点,合成出新型热固性树脂(AFR–T)用作芳纶复合材料的基体,以未经表面处理的芳纶作增强材料,采用热压成型法制备了AFR–T/芳纶纤维复合材料,并通过测定溶度参数、接触角、线膨胀系数、层间剪切强度(ILSS)和横向拉伸强度等方法研究了复合材料的界面粘结性能。结果表明,AFR–T树脂浇注体与芳纶的溶度参数相近,AFR–T树脂溶液在芳纶纸表面的接触角为36.9°,小于环氧树脂(EP)溶液与芳纶纸的接触角(53.2°),说明AFR–T树脂对芳纶的浸润性优于EP;AFR–T/芳纶纤维复合材料的ILSS和横向拉伸强度为73.0 MPa和25.3 MPa,分别比EP/芳纶纤维复合材料提高了25.9%和32.5%,这表明AFR–T树脂与芳纶纤维之间的浸润性和界面粘结性能较好。     

纤维的浸润临界表面张力测定

影响纤维增强塑料力学性能的因素很多,但其中最主要的是纤维与基体界面粘结的状况。界面粘结良好,能很好地传递应力,材料就有较好的力学性能。界面粘结是一复杂的过程,受多种因素的影响。仅从表面热力学角度来考虑,界面粘结强度与热力学粘结功及界面张力这两个物理量有关。一般情况下,实际粘结强度随热力学粘结功增大而提高,随界面张力减低而升高。所以,热力学粘结功和界面张力这两个物理量较普遍地被人们用来判断粘结状态的好坏。为了求得这两个物理量,必须要知道粘结件的表面张力,就复合材料而言,需     

改善玻璃纤维增强塑料动态力学性能的研究

一、引 言 纤维增强塑料的动态力学性能主要依赖于:(1)纤维的强度及模量;(2)树脂的强度及化学稳定性;(3)树脂与纤维间的粘结能力。 在复合材料中,作为基体材料的环氧树脂,由于吸水和环境温度的上升,其力学性能是下降的。当使用的纤维和树脂一定时,如何通过改善树脂与纤维间的粘结来提高复合材料的力学性能,已成为人们当前亟待解决的问题。 六十年代初期,国外许多学者为提高界面的粘结,开始了大量的界面研究工作,并相继提出了化学键理论、表面浸润理论、变形层理论、拘束层理论等等。不论何种     

碳纤维/聚苯并(噁)嗪复合材料的界面与力学性能的关系研究

本文采用含不同上胶剂的碳纤维与苯并(噁)嗪树脂复合,制备碳纤维/聚苯并(噁)嗪单向复合材料,研究了碳纤维表面上胶剂对于复合材料的层间剪切强度(ILSS)、弯曲性能、断口形貌及动态机械性能的影响.结果表明,含有环氧树脂上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(EPCF/PBZ)的ILSS和弯曲性能优于含非环氧类树脂上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(VECF/PBZ)和不含上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(USCF/PBZ).环氧树脂上胶剂改善了纤维与苯并(噁)嗪树脂的粘结性能,使复合材料的内耗峰峰高降低,能量损耗减小.电镜照片同样验证了这一结果.     

原位聚合连续纤维增强聚甲基丙烯酸甲酯复合材料的界面及性能研究

通过选用含不同官能团的硅烷偶联剂3-甲基丙烯酰氧丙基三甲氧基硅烷(MPS)、γ-氨丙基三甲氧基硅烷(APS)和γ-氯丙基三甲氧基硅烷(CPS)处理玻璃纤维,然后通过原位聚合的方法制造了连续纤维增强的聚甲基丙烯酸甲酯(PMMA)复合材料。研究结果表明,经过这三种偶联剂处理的玻璃纤维与基体树脂在界面分别形成了化学键、范德华力和氢键。红外、动态力学分析和扫描电镜研究表明,复合材料的界面粘接强度顺序为:MPS>CPS>APS。MPS处理的复合材料具有最高的弯曲强度,而CPS处理的复合材料具有最佳的冲击韧性和断裂伸长率。     

Influence of fiber wettability on the interfacial adhesion of continuous fiber‐reinforced PPESK composite

Interfacial adhesion between fiber and matrix has a strong influence on composite mechanical performance: better interfacial adhesion can enhance composite transverse properties, flexural properties, and interlaminar shear strength, and so on. To exploit the reinforcement potential of the fibers in advanced composite, it is necessary to reach a deeper understanding on the relation between fiber wettability and interfacial adhesion. In our experiment, we study the influence of fiber wettability on interfacial properties of fiber/PPESK composites by choosing three kinds of fibers with different wettabilities. The relation between fiber wettability and surface free energy was discussed, and the influence of fiber wettability on the interfacial property of fiber/PPESK composites was analyzed. Results indicate that higher surface free energy can enhance the wettability between fiber and matrix, and the humid resistance and interfacial adhesion can be improved at the same time. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2544–2551, 2006     

Kenaf‐bast‐fiber‐filled biodegradable poly(butylene succinate) composites: Effects of fiber loading,fiber length,and maleated poly(butylene succinate) on the flexural and impact properties

Poly(butylene succinate) (PBS) filled kenaf bast fiber (KBF) composites were fabricated via compression molding. The effects of KBF loading on the flexural and impact properties of the composites were investigated for fiber loadings of 10–40 wt %. The optimum flexural strength of the composites was achieved at 30 wt % fiber loading. However, the flexural modulus of the composites kept increasing with increasing fiber loading. Increasing the fiber loading led to a drop in the impact strength of about 57.5–73.6%; this was due to the stiff nature of the KBF. The effect of the fiber length (5, 10, 15, and 20 mm) on the flexural and impact properties was investigated for the 30 wt % KBF loaded composites. The composites with 10‐mm KBF showed the highest flexural and impact properties in comparison to the others. The inferior flexural and impact strength of the composites with 15‐ and 20‐mm KBF could be attributed to the relatively longer fibers that underwent fiber attrition during compounding, which consequently led to the deterioration of the fiber. This was proven by analyses of the fiber length, diameter, and aspect ratio. The addition of maleated PBS as a compatibilizer resulted in the enhancement of the composite's flexural and impact properties due to the formation of better fiber–matrix interfacial adhesion. This was proven by scanning electron microscopy observations of the composites' fracture surfaces. The removal of unreacted maleic anhydride and dicumyl peroxide residuals from the compatibilizers led to better fiber–matrix interfacial adhesion and a slightly enhanced composite strength. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

GF/PP复合材料悬浮法工艺中偶联剂的应用及其对材料性能的影响

研究了悬浮法制备短玻璃纤维增强聚丙烯复合材料过程中不同偶联剂的适用性及其对材料性能的影响。根据悬浮法工艺的特点 ,提出了适用的偶联剂品种和添加方式。探讨了悬浮体系中偶联剂对复合材料微观结构的影响和偶联作用机理     

Influence of fiber modification on interfacial adhesion and mechanical properties of pineapple leaf fiber‐epoxy composites

Three kinds of surface treatment, that is, the alkalization (5% w/v NaOH aqueous solution), the deposition of diglycidyl ether of bisphenol A (DGEBA) from toluene solution (1% w/v DGEBA), and the alkalization combined with the deposition of DGEBA (5% w/v NaOH/1% w/v DGEBA) were applied to modify interfacial bonding and to enhance mechanical properties of pineapple leaf fiber (PALF) reinforced epoxy composites. The fiber strength and strain were measured by single fiber test and the fiber strength variation was assessed using Weibull modulus. Furthermore, a fragmentation test was used to quantify the interfacial adhesion of PALF‐epoxy composite. It was verified that the interfacial shear strength of modified PALFs was substantially higher than that of untreated PALF by almost 2–2.7 times because of the greater interaction between the PALFs and epoxy resin matrix. The strongest interfacial adhesion was obtained from the fibers that had been received the alkalization combined with DGEBA deposition. Moreover, the flexural and impact properties of unidirectional PALF‐epoxy composites were greatly enhanced when reinforced with the modified PALFs due to an improvement in interfacial adhesion, particularly in the synergetic use of 5% NaOH and 5% NaOH/1% DGEBA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

炭纤维表面处理对CF／PMR—15复合材料力学性能的影响

研究了炭纤维表面不同处理方法对复合材料力学性能的影响,采用等离子体和等离子体接枝技术对炭纤维表面进行处理后,CF／PMR－15复合材料的界面剪切强度与层间剪切强度均有所提高,随着界面状态的改善,界面剪切强度提高的幅度比层间剪切强度提高的大,本文为指导炭纤维的表面处理,评价处理效果,进一步预报复合材料的宏观性能打下了基础。     

Evaluation of tribological performance of surface‐treated carbon fiber‐reinforced thermoplastic polyimide composite

The effect of surface treatment [rare earth solution (RES) and air oxidation] of carbon fibers (CFs) on the mechanical and tribological properties of carbon fiber‐reinforced polyimide (CF/PI) composites was comparatively investigated. Experimental results revealed that surface treatment can effectively improve the interfacial adhesion between carbon fiber and PI matrix. Thus, the flexural strength and wear resistance were significantly improved. The RES surface treatment is superior to air oxidation treatment in promoting interfacial adhesion between carbon fiber and PI matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

ABS/SMA/GF复合材料的制备及性能

以丙烯腈-丁二烯-苯乙烯共聚物(ABS)及玻璃纤维(GF)为原料,以苯乙烯-马来酸酐共聚物(SMA)作为界面相容剂,研究界面相容剂对玻璃纤维增强ABS复合材料力学性能及界面粘接的影响.结果表明:加入SMA玻纤增强ABS复合材料的力学性能明显提高;随着玻纤质量分数增加,复合材料的拉伸强度、弯曲强度均逐渐增加,冲击强度下降.     

Influence of surface treatment of carbon fibers on interfacial adhesion strength and mechanical properties of PLA‐based composites

In the present study C/PLA composites with different fiber surface conditions (untreated and with nitric acid oxidation for 4 h and 8 h) were prepared to determine the influence of surface treatment on the interfacial adhesion strength and mechanical properties of the composites. A chemical reaction at the fiber–matrix interfaces was confirmed by XPS studies. Nitric acid treatment was found to improve the amount of oxygen‐containing functional groups (particularly the carboxylic group, —COOH) on carbon fiber surfaces and to increase the surface roughness because of the formation of longitudinal crevices. The treated composites exhibited stronger interface adhesion and better mechanical properties in comparison to their untreated counterparts. There was a greater percentage of improvement in interfacial adhesion strength than in the mechanical properties. The strengthened interfaces and improved mechanical performance have been mainly attributed to the greater extent of the chemical reaction between the PLA matrix and the carbon fibers. The increased surface roughness also has had a slight contribution. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 367–376, 2001