共查询到20条相似文献,搜索用时 156 毫秒
1.
2.
目前我国已经颁布的以数理统计为基础的抽样检验国家标准已有20多项,其中以GB/T2828.1-2003《计数抽样检验程序第1部分按接收质量限(AQL)检索的逐批检验抽样计划》得到了最广泛的应用。采用抽样验 相似文献
3.
近几年来,微电机的发展非常迅速,特别是永磁直流电机产量占世界驱动电机总产量的一半以上,而年增长率又在不断的上升。对于一般中、低档微电机在大批量生产中往往只测量其空载特性、其它性能只是抽样检验。下面介绍几种抽样检验中堵转转矩的测量方法,如图所示。 相似文献
4.
5.
6.
7.
8.
1.关于采用计数抽样问题在《家用电动洗衣机》国标(GB4288—84)检验规则里,引用了GB2828“逐批检查计数抽样程序及抽祥表”,以计数抽样方法检查洗衣机的产品质量,这对提高洗衣机行业的管理水平将起到积极的作用。这主要是因为采用计数抽样方案比百分比抽样更合理。 (1) 当百分比抽取样本大小设定后,不论批量大小都采用同一抽样方案,如交货量大干500台时,则检验数量取交货量的4%(见表1)。 相似文献
9.
介绍了计量抽样检验的基本原理和计量抽检标准的有关内容,举例说明了计量抽检方案在电子式时间继电器延时重复误差检验中的应用。 相似文献
10.
11.
12.
特高压线路工频参数测试干扰分析是选择适合工频参数测试方法及测试结果分析的重要基础。测试了1 000 kV皖南-浙北特高压线路正序和零序参数测试期间的干扰电压信号,分析了其频谱特征;在此基础上,通过与正序参数仿真计算值的对比分析了正序参数实际测试偏差。结果表明:皖南-浙北特高压同塔双回线路工频参数测试期间,干扰电压存在“三相不平衡性及时变性”的特点;工频法和异频法2种不同方法得到的线路参数测试结果存在一定差异;干扰电压“时变”时,线路工频参数测试宜采用异频法。 相似文献
13.
《国外电子测量技术》2014,(10)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world’s premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
14.
《国外电子测量技术》2014,(9)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world's premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
15.
16.
17.
电站锅炉停用保护剂多采用十八胺和表面活性胺。对这2种停用保护剂进行了应用效果对比研究,即对湿冷机组、空冷机组采用十八胺或表面活性胺、有无凝结水精处理系统等6台机组停机和启动过程中给水、主蒸汽和凝结水的氢电导率变化情况进行分析。研究结果表明:在停机过程和启动过程,2种保护剂均会在水汽系统中发生部分分解,导致水汽系统的氢电导率显著升高;表面活性胺和十八胺比较,使用前者,机组启停机过程可保持凝结水精处理系统正常投运,因而可使水汽质量迅速达标,对机组安全运行有利,因此推荐采用表面活性胺作为锅炉停用保护剂。 相似文献
18.
S. Y. Wu B. N. Tran F. Y. Davis C. L. Trent D. L. Edberg W. A. Geideman 《Integrated ferroelectrics》2013,141(3):281-291
Abstract Smart materials of lead-zirconate-titanate (PZT) piezoelectric ceramics have attracted attention in recent years for active vibration control, acoustic noise suppression, health monitoring and damage assessment. We at McDonnell Douglas Aerospace have been studying these ceramics for use as sensors and actuators in various space and aircraft structures. In this paper, we will report results of a recent study on active vibration control using monomorph PZT actuators. The experiments were performed on thin aluminum cantilever beams. Collocated and non-collocated sensors and actuators were employed. Two control techniques: the classical velocity feedback and adaptive feedback controls, were investigated. We have obtained significant damping and broadband vibration attenuation of greater than 30 dB using the classical control with the single-input single-output feedback approach. A 24 dB reduction has also been achieved using the adaptive control with the multiple-input single-output approach. Detailed experimental methods and results will be described. 相似文献
19.
20.
全面、客观地对核一级锻件质量状况给予综合性评判,建立一套适用于锻件质量评价的方法体系很有必要。根据影响核一级锻件质量的制造工艺和成品质量检验,分析了影响锻件质量的主要工艺参数,建立了锻件质量评价的指标体系。在此基础上,探究了基于熵权的逼近理想解排序(TOPSIS)法的特点,建立了相应的评价模型,并将该模型应用于核电站反应堆堆芯筒体锻件的质量评价,获得了堆芯筒体质量状况的优劣排序。研究结果表明:TOPSIS法可有效、科学、客观地评价核一级锻件质量状况,且便于操作、易于推广使用。 相似文献