Hydrogenation of vegetable oils using mixtures of supercritical carbon dioxide and hydrogen

Hydrogenation of vegetable oils under supercritical conditions can involve a homogeneous one-phase system, or alternatively two supercritical components in the presence of a condensed phase consisting of oil and a solid catalyst. The former operation is usually conducted in flow reactors while the latter mode is more amenable to stirred, batch-reactor technology. Although many advantages have been cited for the one-phase hydrogenation of oils or oleochemicals using supercritical carbon dioxide or propane, its ultimate productivity is limited by the oil solubility in the supercritical fluid phase as well as unconventional conditions that affect the hydrogenation. In this study, a dead-end reactor has been utilized in conjunction with a head-space consisting of either a binary fluid phase consisting of varying amounts of carbon dioxide mixed with hydrogen or neat hydrogen for comparison purposes. Reaction pressures up to 2000 psi and temperatures in the range of 120–140°C have been utilized with a conventional nickel catalyst to hydrogenate soybean oil. Depending on the chosen reaction conditions, a wide variety of end products can be produced having different iodine values, percentage trans fatty acid content, and dropping points or solid fat indices. Although addition of carbon dioxide to the fluid phase containing hydrogen retards the overall reaction rate in most of the studied cases, the majority of products have low trans fatty acid content, consistent with a nonselective mode of hydrogenation.     

Synthesis of carbon nanofibers and measurements of hydrogen storage

The synthesis of carbon nanofibers was carried out by catalytic decomposition of ethylene in presence of hydrogen. Bimetallic catalysts, e.g. Fe-Cu or Ni-Cu, were synthesized by coprecipitation, reduction-precipitation and reverse microemulsion techniques and were proven to have a strong influence on the morphology of the nanofibers. The best results in terms of synthesis homogeneity were obtained by supporting the bimetallic catalyst on a high surface area silica support by the “incipient wetness” method. The hydrogen storage capacity of carbon nanofibers was tested in a custom made Sievert apparatus operating up to 160 bar and 450 °C. Several “in situ” activation procedures were experimented, however according to our data carbon nanofibers do not seem a suitable candidate for hydrogen storage. With the purpose of promoting a “spillover” function, 2 wt.% Pd-doped nanofibers were prepared. After loading at 77 bar, a hydrogen storage of 1.38 ± 0.30 wt.% was measured at room temperature.     

The solubility of mixtures of carbon dioxide and hydrogen sulphide in an aqueous dipa solution

The solubility of mixtures of carbon dioxide and hydrogen sulphide in an aqueous solution of di-isopropanolamine (2.5 kmol m^?3 DIPA) has been measured at temperatures of 40 °C and 100°C. Partial pressures of CO₂ ranged from 2.0 to 5991 kPa, while partial pressures of H₂S ranged from 1.3 to 4126 kPa.     

Hydrogenation of chalcones using hydrogen permeating through a Pd and palladized Pd electrodes

The hydrogenation of benzalacetone and benzalacetophenone was carried out using atomic hydrogen permeating through a palladium membrane. A two-compartment cell separated by a Pd sheet or a palladized Pd (Pd/Pd black) sheet electrode was employed. The reduction products were identified by (GC) gas chromatography, UV-vis absorption spectroscopy and NMR spectroscopy. The carbon-carbon double bond was hydrogenated and the benzylacetone and benzylacetophenone were obtained as products using palladium catalyst. The current efficiency for hydrogenation reaction increases when the current density for water electrolysis decreases and depends on the initial chalcone concentration. It is over 90% at the concentration of 10 mmol L⁻¹. The hydrogen absorption and diffusion into and through a palladium membrane electrode has been studied by using an electrochemical impedance spectroscopy method. The impedance results would indicate that the hydrogen permeated through the membrane is consumed by the chalcone during the hydrogenation process keeping as the permeable boundary condition in the outer side of the Pd membrane the hydrogen activity almost zero. The hydrogen entering the metal through an adsorbed state and the rate of hydrogen absorption is diffusion-controlled.     

Preparation, characterization and growth mechanism of platelet carbon nanofibers

The synthesis of platelet carbon nanofibers (PCNFs) on a silicon substrate using chemical vapor deposition method is reported. Scanning electron microscope, high-resolution transmission electron microscopy, and Raman spectroscopy were used to characterize the nanofibers. It is found that these platelet nanofibers are of the order of 10 μm long, and most have a nearly rectangular transverse section with several hundreds nm wide and several tens of nm thick. Structure analysis reveals that the carbon layers of platelet nanofibers are parallel to each other, and have a uniform (0 0 2) orientation that is perpendicular to the fiber axis. Many faults and nanodomain have been found in the nanofibers. It is suggested that the PCNF grow in tip growth mechanism by the precipitation of carbon from the side facet of catalyst flakes.     

Electrochemical quartz crystal microbalance study on carbon oxides adsorption in the presence of electrosorbed hydrogen on Pd alloys with Pt and Rh

CO₂ and CO adsorption on Pd-Pt and Pd-Rh alloys has been studied by cyclic voltammetry (CV) and the electrochemical quartz crystal microbalance (EQCM). Adsorbed CO₂ inhibits partially hydrogen adsorption on Pt and Rh surface atoms but does not block significantly hydrogen absorption into alloy bulk. In the presence of adsorbed CO both hydrogen adsorption and absorption are strongly suppressed. On electrodes covered with adsorbed CO the oxidation of previously absorbed hydrogen is significantly shifted into higher potentials. The EQCM response in CO₂/CO adsorption experiments is affected by both the effects connected with the changes in mass attached to the resonator and the non-mass effects including changes in metal-solution interactions and variation of solution density and viscosity in the vicinity of the electrode. Differences in the EQCM behavior suggest that the products of CO₂ and CO adsorption on the alloys studied are not totally identical.     

The production of carbon nanofibers and thin films on palladium catalysts from ethylene-oxygen mixtures

The characteristics of carbonaceous materials deposited in fuel rich ethylene-oxygen mixtures on three types of palladium: foil, sputtered film, and nanopowder, are reported. It was found that the form of palladium has a dramatic influence on the morphology of the deposited carbon. In particular, on sputtered film and powder, tight ‘weaves’ of sub-micron filaments formed quickly. In contrast, on foils under identical conditions, the dominant morphology is carbon thin films with basal planes oriented parallel to the substrate surface. Temperature, gas flow rate, reactant flow ratio (C₂H₄:O₂), and residence time (position) were found to influence both growth rate and type for all three forms of Pd. X-ray diffraction, high resolution transmission electron microscopy, temperature-programmed oxidation, and Raman spectroscopy were used to assess the crystallinity of the as-deposited carbon, and it was determined that transmission electron microscopy and X-ray diffraction were the most reliable methods for determining crystallinity. The dependence of growth on reactor position, and the fact that no growth was observed in the absence of oxygen support the postulate that the carbon deposition proceeds by combustion generated radical species.     

Super growth of vertically-aligned carbon nanofibers and their field emission properties

We demonstrate a very efficient synthesis of vertically-aligned ultra-long carbon nanofibers (CNFs) with sharp tip ends using thermal chemical vapor deposition. Millimeter-scale CNFs with a diameter of less than 50 nm are readily grown on palladium thin film deposited Al₂O₃ substrate, which activate the conical stacking of graphitic platelets. The field emission performance of the as-grown CNFs is better than that of previous CNFs due to their extremely high aspect ratio and sharp tip angle. The CNF array gives the turn-on electric field of 0.9 V/μm, the maximum emission current density of 6.3 mA/cm² at 2 V/μm, and the field enhancement factor of 2585.     

Mechanical and physical properties of epoxy composites reinforced by vapor grown carbon nanofibers

Epoxy/vapor grown carbon nanofiber composites (VGCF) with different proportions of VGCF were fabricated by the in situ process.The VGCFs were well dispersed in both of the low and high viscosity epoxy matrices, although occasional small aggregates were observed in a high viscosity epoxy of 20 wt.%. The dynamic mechanical behavior of the nanocomposite sheets was studied. The storage modulus and the glass transition temperature (T_g) of the polymer were increased by the incorporation of VGCFs.The electrical and mechanical properties of the epoxy-VGCFs nanocomposite sheets with different weight percentages of VGCFs were discussed. The results were that both had maximum tensile strength and Young’s modulus at 5 wt.% for both materials and reduced the fracture strain with increasing filler content. The electrical resistivity was decreased with the addition of filler content. Mechanical, electrical and thermal properties of low viscosity epoxy composites were resulted better than that of the high viscosity composites.     

Statistical study on the batch conversion of estevan lignite into oils using carbon monoxide and hydrogen mixtures

Batch autoclave hydrogenolysis of a Saskatchewan lignite has been conducted with CO and H₂ mixtures. Conversion, oil yield and the carbon monoxide consumption patterns were measured as a function of reaction temperature (380 — 460°C), initial cold pressure (7.1 — 11.1 MPa), contact time (10 — 50 min), and initial CO/H₂ gas composition (1/3 — 3/1 vol. %). The experimental results were obtained following an unreplicated 2⁴ factorial design. Significant models were derived for conversion and the CO consumption patterns. A relationship seems to develop between carbon monoxide consumption and the amount of oil produced. The oil yield model however showed a lack-of-fit at the F_5% level. The highest conversion and oil yield experimentally obtained were 85.3 and 63.4% respectively, on the lignite m.a.f. basis. In general greater hydrogenation but less deoxygenation occurred at the lower temperature.     

Single Pd atoms in activated carbon fibers and their contribution to hydrogen storage

Palladium-modified activated carbon fibers (Pd-ACF) were synthesized by melt-spinning, carbonization and activation of an isotropic pitch carbon precursor premixed with an organometallic Pd compound. The hydrogen uptake at 25 °C and 20 bar on Pd-ACF exceeded the expected capacity based solely on Pd hydride formation and hydrogen physisorption on the microporous carbon support. Aberration-corrected scanning transmission electron microscopy (STEM) with sub-Ångstrom spatial resolution provided unambiguous identification of isolated Pd atoms occurring in the carbon matrix that coexist with larger Pd particles. First principles calculations revealed that each single Pd atom can form Kubas-type complexes by binding up to three H₂ molecules in the pressure range of adsorption measurements. Based on Pd atom concentration determined from STEM images, the contribution of various mechanisms to the excess hydrogen uptake measured experimentally was evaluated. With consideration of Kubas binding as a viable mechanism (along with hydride formation and physisorption to carbon support) the role of hydrogen spillover in this system may be smaller than previously thought.     

First-principles study of carbon diffusion in bulk nickel during the growth of fishbone-type carbon nanofibers

Ab initio plane wave density functional theory calculations are performed to investigate the carbon diffusion in bulk nickel during the growth of fishbone-type carbon nanofibers (CNFs). Results indicate that the octahedral interstitial sites are preferred for C dissolution relative to the tetrahedral sites. And the heat of solution of C in paramagnetic (PM) Ni is larger than that in ferromagnetic (FM) Ni because the induced C atom quenches the magnetic moments of neighboring Ni atoms. The bulk diffusion has been successfully described under two different C concentrations. At the initial CNF growth stage, the C concentration in bulk Ni is low and the calculated energy barriers for the diffusion of an isolated C atom are 1.641 eV and 1.678 eV in the Ni FM and PM state, respectively. When the C content is increased to 20 at.%, two models are established. In one case, it is assumed that all C atoms hop in the same direction at the same time, and the calculated activation energies are 1.137 eV and 1.126 eV. In the other case, only one C atom is permitted to move with the neighboring C atoms fixed at the octahedral sites and the corresponding barriers are decreased to 0.972 eV in the Ni FM state. Through these calculations, it is concluded that the magnetic state has a minor effect on the diffusion energy barrier which can be substantially lowered by the increase of C concentration in bulk Ni. Comparing the activation energy for bulk diffusion with the surface diffusion results, the reason for the formation of different CNF morphologies has been revealed.     

Influence of adsorbed carbon dioxide on hydrogen electrosorption in palladium-platinum-rhodium alloys

Carbon dioxide electroreduction was applied to examine the processes of hydrogen electrosorption (adsorption, absorption and desorption) by thin electrodeposits of Pd-Pt-Rh alloys under conditions of cyclic voltammetric (CV) experiments. Due to different adsorption characteristics towards the adsorption product of the electroreduction of CO₂ (reduced CO₂) exhibited by the alloy components hydrogen adsorption and hydrogen absorption signals can be distinguished on CV curves. Reduced CO₂ causes partial blocking of hydrogen adsorbed on surface Pt and Rh atoms, without any significant effect on hydrogen absorption into alloy. It reflects the fact that adsorbed hydrogen bonded to Pd atoms does not participate in CO₂ reduction, while hydrogen adsorbed on Pt and Rh surface sites is inactive in the absorption reaction. In contrast, CO is adsorbed on all alloy components and causes a marked inhibition of hydrogen sorption (both adsorption and absorption)/desorption reactions.     

Lignin‐based carbon fibers: Accelerated stabilization of lignin fibers in the presence of hydrogen chloride

Organosolv switchgrass lignin (SGL) and hardwood lignin (HWL) polymers are used as precursors to prepare low cost carbon fibers (CFs). Lignin powder and fiber samples are stabilized and carbonized at different conditions to investigate the effect of HCl on thermal‐oxidative stabilization time, mass yield, fiber diameter, and mechanical properties. The results show that HCl can accelerate stabilization and reduce the stabilization time from many hours to 75 min for the SGL fibers, and to 35 min for the HWL fiber. The rate of rapid stabilization in HCl/air is at least four times faster than conventional stabilization in air. The CFs prepared with two different stabilization methods have almost the same strength and modulus, but higher carbon yield is obtained with the rapid stabilization due to a short time of oxidation. Pores and defects observed on the surface and the cross‐section of the CFs across all stabilization conditions contribute to low fiber strength. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45507.     

Evidence for growth mechanism and helix-spiral cone structure of stacked-cup carbon nanofibers

New evidence for the structure of Ni-catalyzed stacked-cup carbon nanofibers (CNFs) has been found. This type of carbon nanofiber exhibits a wide hollow core as well as a large diameter (between 40 and 140 nm). The fibers have been produced by the floating catalyst method using natural gas as carbon feedstock, a sulfur compound, and a nickel catalyst. It was found that the catalytic particles are heterogeneous with two different parts: one composed of metallic Ni, which is the catalytically active portion of the particle, and another composed of NiS, which allows for the hollow nanofiber structure. The hollow core of the fibers has similar dimensions to the NiS volume of the particle and the graphitic layers grow from the rear nickel region of the particle. Nevertheless, the NiS component seems to be indispensable in producing the helix-spiral formation of the graphitic structure, as clearly shown by the TEM studies.     

Effect of oxygen and hydrogen addition on the low-temperature synthesis of carbon nanofibers using a low-temperature CO/Ar DC plasma

The low-temperature synthesis of carbon nanofibers was demonstrated. When a small amount of O₂ was added to the CO/Ar plasma, the diameter of the CNFs decreased and the deposition of amorphous carbon and fiber bundling were suppressed. On the other hand, when H₂ was added, the diameter increased, and at higher H₂ flow rates, only smooth carbon film was deposited. At the optimum oxygen concentration of CO/O₂ = 1/0.003, vertically aligned free-standing CNFs can be synthesized at low temperature as low as 90 °C. Our spectroscopic study reveals that there is a steady correlation between C₂ radical formation and CNFs growth.