Magnetocrystalline anisotropy of Nd3(Fe1−xCox)27.7Ti1.3Ny compounds

The effect of Co substitution for Fe in Nd₃(Fe_1−xCo_x)_27.7Ti_1.3N_y (0 ≤ x ≤ 0.4) compounds on the magnetocrystalline anisotropy has been investigated. The anisotropy constants K's and the anisotropy field H_A have been deduced from the magnetization curves measured on magnetically aligned powder (4–7 μm) samples. The obtained results show that at RT the anisotropy is uniaxial and H_A (about 10 T) does not change substantially upon the substitution. At 5 K the results for K's give evidence for the presence of easy-cone-type anisotropy. The cone angle as well as the anisotropy field decrease upon the substitution from 21.6° to 11.8° and from 22.8 to 18.6 T, respectively.     

Electrical, magnetic and elastic properties of La1.2(Sr1−xCax)1.8Mn2O7 (0.0 ≤ x ≤ 0.4)

Polycrystalline bulk samples of double layered manganite system La_1.2(Sr_1−xCa_x)_1.8Mn₂O₇ (0.0 ≤ x ≤ 0.4) were prepared by sol–gel method. After characterizing the samples using XRD and SEM, their electrical, magnetic and elastic properties were investigated. The lattice parameters and cell volume show a monotonous decrease with increase of Ca content, whereas the grain size is found to increase with increasing Ca content. The value of T_IM is found to decrease with Ca content up to x = 0.3 and then a slight increase of T_IM is observed. The low temperature upturn of resistivity is attributed to the spin-glass-like behavior, which is also evidenced by the irreversibility observed between ZFC and FC magnetizations. The conduction mechanism above T_IM can be explained by Mott VRH model. The present magnetization and ultrasonic studies indicate that the system shows a secondary transition at T^*, which decreases with increasing Ca content. Further, the T^* seems to be intrinsic to the present double layered manganite system.     

Magnetic properties of CeMn2−xCoxGe2

The structure and magnetic properties of CeMn_2−xCo_xGe₂ (0.0≤x≤1.0) were studied by X-ray powder diffraction and magnetization measurements. All compounds crystallize in the ThCr₂Si₂-type structure with space group I4/mmm. Substitution of Co for Mn leads to a linear decrease in the lattice constants and the unit cell volume. Increasing substitution of Co for Mn shows a depression of ferromagnetic ordering.     

Magnetic phase transitions in Nd1−xYxMn2Ge2 (0 ≤ x ≤ 0.6)

The structure and magnetic properties of Nd_1−xY_xMn₂Ge₂ (0.0≤x≤0.6) were studied by X-ray powder diffraction and magnetization measurements. All compounds crystallize in the ThCr₂Si₂-type structure with space group I4/mmm. Substitution of Y for Mn led to a linear decrease in the lattice constants and the unit cell volume. Increasing substitution of Y for Nd in NdMn₂Ge₂ shows a depression of ferromagnetic ordering and the gradual development of antiferromagnetic ordering.     

Synthesis and characterization of LiGaxMn2−xO4 (0 ≤ x ≤ 0.05) by triethanolamine-assisted sol–gel method

Spinel LiGa_xMn_2−xO₄ (0 ≤ x ≤ 0.05) cathode materials with phase-pure particles and nano-sized distribution were synthesized by sol–gel method using triethanolamine as the chelating agent. The effects of heat treatment on the physicochemical properties of the spinel LiGa_xMn_2−xO₄ powders were examined with thermogravimetric and differential thermal analysis (TG/DTA), powder X-ray diffraction (XRD) and scanning electron micrograph (SEM). The LiGa_xMn_2−xO₄ (0 ≤ x ≤ 0.05) electrodes were characterized electrochemically by charge/discharge experiments under a current rate of 0.5C at 55 °C. Although the Ga-doped spinel electrode showed smaller initial discharge capacity, it exhibited better cycling performance than the undoped-LiMn₂O₄ electrode. The dQ/dV versus potential plots at 55 °C revealed that the improvement in cycling performance of the Ga-doped spinel electrode is attributed to stabilization of the spinel structure by the presence of gallium ion.     

X-ray diffraction and Mössbauer study of (Fe1−xNix)4N (0.2 ≤ x ≤ 0.6) films

Single phase (Fe_1−xNi_x)₄N compounds (0.2 ≤ x ≤ 0.6) have been synthesized by reactive evaporation and investigated by X-ray diffraction and Mössbauer spectrometry. The lattice parameters of the nitrides decrease from 3.796 to 3.774 Å with increasing Ni concentration. The fitting results of Mössbauer spectra indicate that the average hyperfine field have the same changing tendency with lattice parameter and the nickel atoms have a tendency to be located at the corner site.     

Roles of lithium ions and La/Li-site vacancies in sinterability and total ionic conduction properties of polycrystalline Li3xLa2/3−xTiO3 solid electrolytes (0.21 ≤ 3x ≤ 0.50)

The Li_0.33La_0.55TiO₃ solid electrolyte has a maximum grain ionic conductivity of 1.13 × 10⁻³ S cm⁻¹ among the Li_3xLa_2/3−xTiO₃ oxides (0.21 ≤ 3x ≤ 0.50), but the total ionic conductivity of its polycrystalline phase is not the highest. Owing to the grain-boundary resistances controlling the total resistances of bulk samples, an excellent solid electrolyte is mainly characterized by the grain-boundary resistances. With regard to the role of lithium ions, the substitution of La³⁺ ions by the Li⁺ ions weakens the strength of inter-ionic forces, leading to the decrease in the sintering temperature. The presence of La³⁺/Li⁺-site vacancies promotes the densification and grain growth and further results in rapid decreases in porosity and grain-boundary resistances. Li_0.21La_0.60TiO₃ with a larger amount of La³⁺/Li⁺-site vacancies can therefore exhibit the highest total ionic conductivity through rapidly decreasing its grain-boundary resistances by changing its microstructure, and it becomes a better polycrystalline solid electrolyte than Li_0.33La_0.55TiO₃ in the Li_3xLa_2/3−xTiO₃ system studied, in spite of its lower grain ionic conductivity.     

Evolution of magnetic hardness in the HfFe6Ge6-type RMn6Sn6−xGax and RMn6Sn6−xInx compounds (R=Tb, Dy; 0.2≤x≤1.4)

The HfFe₆Ge₆-type RMn₆Sn_6−xX_x′ solid solutions (R=Tb, Dy, X′=Ga, In; x≤1.4) have been studied by powder magnetization measurements. All the series are characterized by ferrimagnetic ordering and by a decrease in Curie temperatures with the substitution (ΔT_c/Δx≈−39 K for X′=Ga and ΔT_c/Δx≈−75 K for X′=In). The RMn₆Sn_6−xGa_x systems are characterized by a strong decrease in the spin reorientation temperature with substitution (ΔT_t/Δx≈−191 K and −78 K for R=Tb and Dy, respectively) while this transition almost does not change in systems containing indium. The coercive fields drastically decrease with the substitution in the TbMn₆Sn_6−xGa_x system while the substitution of In for Sn has a weaker effect. The coercive fields of the Dy compounds do not vary greatly with the substitution in both series. The behaviour of the TbMn₆Sn_6−xGa_x is compared with the evolutions observed in the TmMn₆Sn_6−xGa_x series. This comparison strongly suggests that the replacement of Sn by Ga changes the sign of the A₀² crystal field parameter.     

Corrosion resistance of (Nd,Dy)16(Fe,Co)76−xTixB8 mechanically alloyed magnets

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at.% of Ti results in increase of coercivity from 796 to 1115 kA/m. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA/m. The highest corrosion resistance have magnets with 0.5–0.75 at.% of Ti. Beside the Ti, the Co and Dy content significantly improve the corrosion resistance, too. It was found, that for Ti content smaller than x ≤ 1, the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x > 1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity as well as corrosion resistance decreases due to the presence of an amorphous phase and -Fe. A heat treatment at a higher temperature (1073 K/30 min) or at 973 K for longer time (1 h) results in the full recrystallisation of the powders. The obtained homogenized structure results in higher corrosion resistance.     

Characterization and hydrogenation of CeNi5−xCrx (x = 0, 1, 2) alloys

The effect of partial substitution of Ni by Cr in CeNi₅ intermetallic compound has been studied by pressure–composition isotherm measurements for different temperatures. The samples were prepared of high purity materials using the standard arc melting technique in argon atmosphere. The structure and the elemental composition of different alloys have been investigated by means of XRD, SEM and EDX techniques. The unit cell volume of the alloy was found to increase with increasing Cr content. In order to calculate the hydrogen storage capacity pressure–composition isotherm has been investigated for CeNi_5−xCr_x (x = 1, 2) alloys in the temperature and pressure ranges of 293 ≤ T ≤ 333 K and 0.5 ≤ P ≤ 35 bar, respectively. The P–C–T isotherm for different alloys clearly shows the presence of three regions ,  + β and β. The enthalpy and entropy for the systems has also been calculated using Van’t Hoff plot. The variation of enthalpy and entropy with hydrogen content has also been studied.     

The characteristics of Li(CoxNi1 − x)O2 cathode powders formed from the fine-sized Co3O4/NiO precursor powders

Li(Co_xNi_1 − x)O₂ (0 ≤ x ≤ 1) cathode powders were prepared by solid state reaction method using Co₃O₄/NiO precursor powders obtained by spray pyrolysis. The effect of the ratios of cobalt and nickel components on the characteristics of Co₃O₄/NiO precursor and Li(Co_xNi_1 − x)O₂ cathode powders were investigated. The Co₃O₄/NiO precursor powders with the ratios of cobalt and nickel components as 1/0, 0.75/0.25 and 0.5/0.5 had submicron size and regular morphologies. On the other hand, the Co₃O₄/NiO powders with the high contents of nickel component had aggregated morphologies of submicron size primary powders. The fine-sized precursor powders formed the fine-sized LiCoO₂ and Li(Co_0.75Ni_0.25)O₂ cathode powders by solid state reaction with LiOH powders. However, the high contents of the nickel component of the Co₃O₄/NiO precursor powders formed the Li(Co_xNi_1 − x)O₂ (0 ≤ x ≤ 0.5) cathode powders with aggregated morphologies and large sizes. The discharge capacities of the powders increased with increasing the nickel content into the Li(Co_xNi_1 − x)O₂ cathode powders up to 188 mAh/g.     

Power factor of La1−xSrxFeO3 and LaFe1−yNiyO3

The electrical conductivity (σ), Seebeck coefficient (S), and power factor (σS²) of perovskite-type LaFeO₃, La_1−xSr_xFeO₃ [0.1 ≤ x ≤ 0.4] and LaFe_1−yNi_yO₃ [0.1 ≤ y ≤ 0.6] were investigated in the temperature range of 300–1100 K to explore their possibility as thermoelectric materials. The electrical conductivity of LaFeO₃ showed semiconducting behavior, and its Seebeck coefficient changed from positive to negative around 650 K with increasing temperature. The electrical conductivity of LaFeO₃ increased with the substitutions of Sr and Ni atoms, while its Seebeck coefficient decreased. The Seebeck coefficient of La_1−xSr_xFeO₃ was positive, whereas that of LaFe_1−yNi_yO₃ changed from positive to negative with increasing Ni content. The substitutions of Sr and Ni were effective in increasing the power factor of LaFeO₃; 0.0053 × 10⁻⁴ Wm⁻¹ K⁻² for LaFeO₃ (1050 K), 1.1 × 10⁻⁴ Wm⁻¹ K⁻² for La_1−xSr_xFeO₃ (x = 0.1 at 1100 K) and 0.63 × 10⁻⁴ Wm⁻¹ K⁻² for LaFe_1−yNi_yO₃ (y = 0.1 at 1100 K).     

Hydrogen disproportionation by reactive milling and recombination of Nd2(Fe1−xCox)14B alloys

Stoichiometric Nd₂(Fe_1−xCo_x)₁₄B alloys (x=0, 0.25, 0.5, 0.75 and 1) have been disproportionated into NdH_2+δ and bcc–(Fe,Co) (0≤x≤0.75) or fcc–Co (x=1), respectively, by milling in hydrogen at enhanced temperatures. Reactive milling leads to the disproportionation of the thermodynamically very stable Nd₂Co₁₄B alloy. This reaction is not possible via the conventional hydrogenation disproportionation desorption and recombination (HDDR) process. Grain sizes of disproportionated and recombined Nd₂(Fe,Co)₁₄B materials were found to be <10 nm and 40–50 nm, respectively — approximately an order of magnitude smaller than those of conventional-HDDR processed alloys. The recombined Nd₂Co₁₄B alloy shows on average slightly smaller grain sizes than the Nd₂Fe₁₄B compound. A more effective exchange coupling leading to enhanced remanences, possibly due to the slightly smaller grain size, has been observed for Nd₂Co₁₄B powders recombined at 600–700°C.     

Correlation between the synthesis conditions and the compositional and magnetic properties of Co2(Cr1−xFex)Al Heusler alloys

In this study we give evidence for the strong dependence of the compositional and magnetic properties on the synthesis conditions of polycrystalline Co₂(Cr_1−xFe_x)Al Heusler alloys (0 ≤ x ≤ 1) by comparing the properties of as-grown and annealed compounds. Strong chemical inhomogeneities are found at the micrometric level depending on the compound and the synthesis method. Moreover, we find that the Co content is homogeneous at the micrometric level in all the studied samples in sharp contrast with significant inhomogeneous distribution of (Fe/Cr) and Al at the micrometric level, especially for Cr-rich compounds (x ≤ 0.4). We have found that the magnetic properties (the Curie temperature and the saturation magnetization) are strongly depressed in the annealed compounds with respect to the corresponding as-grown compounds. For the as-grown compounds the saturation magnetization is close to the theoretically predicted one for x ≥ 0.7 whereas it is lower than the theoretically predicted one for x ≤ 0.4, which correlates with the observed chemical inhomogeneity.     

Phase behavior and some properties of LaMn1−xRhxO3 solid solution

Structure and magnetic and electrical properties of the polycrystalline compounds LaMn_1−xRh_xO₃ (0 < x ≤ 1) have been investigated. The samples were characterized by X-ray diffraction and Rietveld refinement which confirmed the space group Pnma (No. 62) for all compositions at room temperature. A transformation from O′- to O-type orthorhombic structure is seen near x = 0.6 tending to make the phase unstable. The electrical conductivity measurement shows semiconducting property above room temperature with a rather low activation energy for Mn-rich compositions. Compounds in the region 0.1 ≤ x ≤ 0.9 show ferromagnetic property but the substitution of Rh³⁺ ion for Mn³⁺ ion suppresses the ferromagnetism that results in reducing the Curie temperature, T_C.     

Bulk and lattice thermal expansion in Ce1−xSrxO2−x (0.0≤x≤0.10)

In this communication, we report on the bulk and lattice thermal expansion studies on a number of compounds, within the homogeneity range of solid solutions, in a series with the general composition Ce_1−xSr_xO_2−x (0.0≤x≤0.10). The XRD pattern of each product was refined to determine the solid solubility of SrO into the lattice of CeO₂, and the homogeneity range. The composition with maximum solid solubility limit of SrO in CeO₂ lattice, under the slow cooled conditions, was delineated as Ce_0.91Sr_0.09O_1.91 (i.e. 9 mol.% of SrO). The bulk thermal expansion measurements from ambient to 1123 K, as investigated by a dilatometer, revealed that the _l (293 to 1123 K) values for the compositions within the homogeneity range increase from 11.58×10⁻⁶ to 12.13×10⁻⁶ K⁻¹ on increasing the Sr²⁺ content from 0 mol.% (i.e. CeO₂) to 9 mol.%, i.e. the upper solubility limit of SrO into the lattice of CeO₂. A similar trend was observed in the lattice thermal expansion coefficients _a (293 to 1473 K) as obtained by a high temperature-XRD.     

Subsolidus phase relation and crystal structure of the PrBa2−xSrxCu3O7±δ system

The PrBa_2−xSr_xCu₃O_7±δ solid solution was investigated by means of X-ray powder diffraction in combination with Rietveld analysis. The Sr-doped Pr123 single phase could be synthesized at 950 °C in air. The solubility of PrBa_2−xSr_xCu₃O_7±δ solid solution is 0.2≤x≤0.6. The structure of PrBa_2−xSr_xCu₃O_7±δ is orthorhombic for x=0.2. The structure transforms into tetragonal for 0.3≤x≤0.6. In the PrBa_2−xSr_xCu₃O_7±δ structure, Sr ions can replace Ba ions, the highest value is x=0.6 under our experimental condition. But Sr ions could not replace Pr ions. Furthermore Pr ions could not occupy the sites of Ba ions in the PrBa_2−xSr_xCu₃O_7±δ system. Both ionic radii and chemical properties play an important role in the mutual substitution of Pr, Ba and Sr ions in the Pr123 structure of the PrBa_2−xSr_xCu₃O_7±δ system.     

Structural, magnetic and magnetostrictive studies of Tb0.27Dy0.73(Fe1 − xAlx)2

Measurements of magnetic properties, X-ray diffraction and magnetostriction were made on Tb_0.27Dy_0.73(Fe_{1 − x}Al_x)₂ (x = 0.1, 0.2, …, 0.7) compounds. It was found that the system has the cubic MgCu₂ structure over almost the whole (Fe,Al) concentration range investigated, except for a narrow intermediate range (x = 0.4–0.6) where the hexagonal MgZn₂ structure appears. With increasing Al content x, the lattice constant a increases linearly with x. The first replacement of Fe results in a marked decrease in the Curie temperature, which is followed by a slight decrease in T_C with x. A linear decrease in magnetostriction of |λ_| − λ| at room temperature with x was also observed from 1530 × 10⁻⁶ for x=0 to 36×10⁻⁶ for x=0.3. The saturation magnetization σ_s exhibits a complex concentration dependence in the Tb_0.27Dy_0.73(Fe)_{1 − x}Al_x)₂ system: in the range x < 0.5, σ_s increases linearly with x and, for x = 0.5–0.6, σ_s decreases and then increases again. An enhancement of the magnetic ‘hardness’ in this system was also observed at low temperature.     

Structure and magnetic properties of TbFe10.5−x MnxMo1.5 compounds

The effects of Mn partial substitution for Fe in TbFe_10.5Mo_1.5 on the structure and magnetic properties were investigated. TbFe_10.5−xMn_xMo_1.5 samples (x = 1.5, 2.0, 3.0, 4.0, 5.0) were prepared by means of arc-melting and subsequent vacuum annealing. The structure and magnetic properties of TbFe_10.5−xMn_xMo_1.5 compounds were investigated by X-ray powder diffraction and magnetic properties measurements. The following conclusions were obtained: all the TbFe_10.5−xMn_xMo_1.5 compounds studied crystallize in the ThMn₁₂-type structure; the unit-cell volume increases monotonically with increasing Mn concentration; a compensation temperature was observed in the magnetization-temperature curve of TbFe_7.5Mn₃Mo_1.5 compounds. With increasing Mn concentration, the saturation magnetization at 4.4 K decreases to zero, and then increases again, the magnetic moments of the transition-metal sublattice of TbFe_10.5−xMn_xMo_1.5 compounds decrease monotonically.     

HfFe6Ge6-type YbMn6Ge6−xGax compounds (0.07≤x<0.72) with large magnetocrystalline anisotropy

The HfFe₆Ge₆-type YbMn₆Ge_6−xGa_x solid solution (0.07≤x≤0.72) has been studied by X-ray diffraction, microprobe analysis and powder magnetization measurements. All the compounds order antiferromagnetically between T_N=481 K for x=0.07 and T_N=349 K for x=0.72 and display more or less pronounced spontaneous magnetization at lower temperature. The corresponding Curie points increase from 40 K for x=0.07 to 319 K for x=0.72. The maximum magnetization values of the Ga-rich compounds (M≈5 μ_B/f.u. at 6 K) is compatible with a ferrimagnetic order of the Mn and Yb sublattices whereas the smaller values measured in the Ga-poor compounds suggest the stabilization of non-colinear magnetic structures. All the studied compounds are characterized by rather large coercive fields at low temperature (4.0≤H_c≤8.2 kOe).