Effect of M-doping (M = Fe,V) on the photocatalytic activity of nanorod rutile TiO2 for Congo red degradation under the sunlight

Nanorods TiO₂, Fe-TiO₂ (3 and 2 at.% Fe), V-TiO₂ (5 at.% V) were prepared by a low temperature method and characterized by powder X-ray diffraction, thermal analysis, transmission electron microscope and BTE surface area analysis. The as-prepared samples were evaluated as catalysts for photodegradation of Congo red aqueous solution under the sunlight. Nanorods Fe-doped TiO₂ shows higher adsorption and also higher photocatalytic degradation of Congo red solution compared to pure nanorods TiO₂ rutile. A higher activity is obtained when the amount of doped Fe is 2 at.%, compared to 3 at.%. However, nanorods V-TiO₂ does not show neither adsorption nor photodegradation activity of Congo red solution.     

Synthesis and Photocatalytic Activity of Anatase TiO2 Nanoparticles-coated Carbon Nanotubes

A simple and straightforward approach to prepare TiO₂-coated carbon nanotubes (CNTs) is presented. Anatase TiO₂ nanoparticles (NPs) with the average size ~8 nm were coated on CNTs from peroxo titanic acid (PTA) precursor even at low temperature of 100 °C. We demonstrate the effects of CNTs/TiO₂ molar ratio on the adsorption capability and photocatalytic efficiency under UV–visible irradiation. The samples showed not only good optical absorption in visible range, but also great adsorption capacity for methyl orange (MO) dye molecules. These properties facilitated the great enhancement of photocatalytic activity of TiO₂ NPs-coated CNTs photocatalysts. The TiO₂ NPs-coated CNTs exhibited 2.45 times higher photocatalytic activity for MO degradation than that of pure TiO₂.     

水热法制备TiO2片晶及光催化性能

以稳定的金红石相TiO₂为原料,水热法制备出微米级TiO₂片晶。采用扫描电镜（SEM）、X射线粉末衍射（XRD）、N₂吸附-脱附等分析手段对样品进行了分析。将不同温度下煅烧后样品进行甲基橙降解实验。实验结果表明,反应48 h可获得长60～80μm、宽30～60μm、厚4～9 μm的介孔片晶。经450℃煅烧可得到锐钛矿相占83.6%的混晶,比表面和孔径分别为68 m²·g^-1、21.6 nm,对甲基橙降解率最高,在30 min内降解了92.4%,60 min几乎全部降解,其催化活性优于商用P25,且微米级的颗粒更容易回收再利用。     

Preparation and characterization of SO42-/TiO2 and S2O82-/TiO2 catalysts

Nanosized solid superacids SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂, as well as MCM-41-supported SO₄ ²⁻/ZrO₂, were prepared. Their structures, acidities, and catalytic activities were investigated and compared using XRD, N₂ adsorption-desorption, and in situ FTIR-pyridine adsorption, as well as an evaluation reaction with pseudoionone cyclization. The results showed that SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ possess not only nanosized particles with diameters < 7.0 nm, a BET surface greater than 140 cm²/g and relatively regular mesostructures with pores around 4.0 nm, but also a pure anatase phase and strong acidity. Different from the Lewis acid nature of SO₄ ²⁻/ZrO₂/MCM-41, SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ exhibit mainly Bronsted acidities. The strongest Bronsted acid sites were produced on SO₄ ²⁻/TiO₂ promoted with H₂SO₄, while Lewis acid sites on S₂O₈ ²⁻/TiO₂ even stronger than those on SO₄ ²⁻/ZrO₂/MCM-41 were generated when persulfate solution was used as sulfating agent. Because of their distinct acid natures, SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ exhibited catalytic activities for the cyclization of pseudoionone that were much higher than that of SO₄ ²⁻/ZrO₂/MCM-41. It can be concluded that the existence of more Br?nsted acid sites was favorable for proton participation in the cyclization reaction. Translated from Journal of Chemical Engineering of Chinese Universities, 2006, 20(2): 239–244 [译自: 高校化学工程学报]     

Physico-chemical properties of WO3/TiO2 systems employed for 4-nitrophenol photodegradation in aqueous medium

A series of polycrystalline WO_x/TiO₂ samples were prepared by means of a conventional impregnation method. The samples were characterized by means of X-ray diffraction, Vis-UV diffuse reflectance and Raman spectroscopies, nitrogen adsorption at 77 K for determining specific surface areas and surface texture, scanning electron microscopy, and FT-IR monitoring of pyridine adsorption for measuring the surface acidity. Catalytic activity of the samples has been assessed by carrying out as a ``probe'' reaction the photodegradation of 4- nitrophenol in aqueous medium. The results obtained indicate that incorporation of tungsten on titania leads to formation of different surface species, depending on the tungsten loading. Tungsta microcrystals were detected by X-ray diffraction when the nominal molar W/Ti ratio reached a value of 8.0%. FT-IR investigation indicated that the presence of tungsten induces formation of Brønsted and Lewis surface acid sites. The photoactivity results confirm the beneficial effect of tungsten in TiO₂ for 4-nitrophenol photodegradation in aqueous medium. The reaction rates are higher than those reported in literature for another set of samples and maximum photoactivity was achieved for a sample containing 1.96 moles of W per 100 moles of Ti.     

Photocatalytic activity of TiO2 supported on multi-walled carbon nanotubes under simulated solar irradiation

TiO₂ particles supported on multi-walled carbon nanotubes (MWCNTs) were prepared using a sol–gel method to investigate their photocatalytic activity under simulated solar irradiation for the degradation of methyl orange (MO) in aqueous solution. The prepared composites were analyzed using XRD, SEM, EDS and UV–vis absorption spectroscopy. The results of this study indicated that there was little difference in the shape and structure of MWCNTs/TiO₂ composite and pure TiO₂ particles. The composite exhibited enhanced absorption properties in the visible light range compared to pure TiO₂. The degradation of MO by MWCNTs/TiO₂ composite photocatalysts was investigated under irradiation with simulated solar light. The results of this study indicated that MWCNTs played a significant role in improving photocatalytic performance. Different amounts of MWCNTs had different effects on photodegradation efficiency, and the most efficient MO photodegradation was observed for a 2% MWCNT/TiO₂ mass ratio. Photocatalytic reaction kinetics were described using the Langmuir–Hinshelwood (L–H) model. The photocatalyst was reused for eight cycles, and it retained over 95.2% photocatalytic degradation efficiency. Possible decomposition mechanisms were also discussed. The results of this study indicated that photocatalytic reactions with TiO₂ particles supported on MWCNTs under simulated solar light irradiation are feasible and effective for degrading organic dye pollutants.     

Facile preparation of Na-free anatase TiO2 film with highly photocatalytic activity on soda-lime glass

Na-free anatase TiO₂ film was prepared on soda-lime glass (SL-glass) from a TiF₄ aqueous solution upon addition of boric acid at 60 °C. It was found that the as-prepared TiO₂ film before calcination showed a higher photocatalytic activity than the calcined sample (500 °C). This could be attributed to the fact that the calcined TiO₂ film contained decent Na⁺ ions, which was diffused from the SL-glass substrate into the TiO₂ film during calcination, resulting in the decrease of photocatalytic activity.     

Comparison of Different Photocatalytic Systems for Acetonitrile Degradation in Gas–solid Regime

Photocatalytic degradation of acetonitrile was carried out in gas–solid regime by using two commercial TiO₂ samples (Merck and Degussa P25) irradiated in two continuous annular photoreactors. The inlet gas flow consisted of oxygen, nitrogen, acetonitrile and water vapours. The influence on the photodegradation rate of gas flow rate, acetonitrile, oxygen and water concentrations and photon flux was investigated. The degradation products of acetonitrile were carbon dioxide and hydrogen cyanide. The photocatalysts performance was not affected by the presence or absence of water vapour in the reacting mixture. The Langmuir–Hinshelwood model describes adequately the photoreactivity results and provides the values of kinetic and equilibrium adsorption constants. FT-IR spectroscopy was used to investigate the adsorption patterns and photo-oxidation intermediates of acetonitrile on fully hydrated surface of TiO₂ powders. Acetonitrile was adsorbed on Ti⁴⁺ surface ions and hydroxyl groups for both types of TiO₂. In the absence of UV light this interaction was completely reversible for Merck catalyst whereas for Degussa P25 part of adsorbed acetonitrile molecules reacted to form acetamide-like species.     

Li1.6Mn1.6O4/PVDF多孔膜的制备及提锂性能

自制锂离子筛前驱体Li_1.6Mn_1.6O₄，并将Li_1.6Mn_1.6O₄粒子与高分子树脂PVDF杂化制膜，研究了膜经稀盐酸抽锂后对锂的吸附性能以及多次吸附与脱附性能等。结果表明，膜M-10-55[Li]采用0.5 mol·L^-1 HCl溶液抽锂约2 h锂的脱出基本达到平衡，Li⁺的洗脱率在95%左右，锰的溶损率为3.5%左右。抽锂后得M-10-55[H]对富锂溶液中锂的吸附约12 h达平衡，对锂的吸附容量较高为41 mg·g^-1，在第5次吸附时对锂的提取量为35 mg·g^-1左右。相比于Na⁺、K⁺、Mg²⁺、Ca²⁺，该膜对Li⁺表现出较好的选择性，对于从海水、盐湖卤水等液态锂资源中提取锂有很大的开发潜力。     

A kinetic and DRIFTS study of low-temperature carbon monoxide oxidation over Au-TiO2 catalysts

Titania-supported gold catalysts are extremely active for room temperature CO oxidation; however, deactivation is observed over long periods of time under our reaction conditions Impregnated AuTiO₂ is most active after a sequential pretreatment consisting of high temperature reduction at 773 K, calcination at 673 K and low temperature reduction at 473 K (HTR/C/LTR); the activity after either only low temperature reduction or calcination is much lower. A catalyst prepared by coprecipitation had much smaller Au particles than impregnated AuTiO₂ and was active at 273 K after either an HTR/C/LTR or a calcination pretreatment. Deposition of TiO_x overlayers onto an inactive Au powder produced high activity; this argues against an electronic effect in small Au particles as the major factor contributing to the activity of AuTiO₂ catalysts and argues for the formation of active sites at the AuTiO_x interface produced by the mobility of TiO_x species. DRIFTS (diffuse reflectance FTIR) spectra of impregnated AuTiO₂ reveal the presence of weak reversible CO adsorption on the Au surface but not on the TiO₂; however, a band for adsorbed CO is observed on the pure TiO₂. Kinetic studies with a 1.0 wt.-% impregnated AuTiO₂ sample showed a near half-order rate dependence on CO and a near zero-order rate dependence on O₂ between 273 and 313 K with an activation energy near 7 kcal/mol. A two-site model, with CO adsorbing on Au and O₂ adsorbing on TiO₂, is consistent with Langmuir-Hinselwood kinetics for noncompetitive adsorption, fits partial pressure data well and shows consistent enthalpies and entropies of adsorption. The formation of carbonate and car☐ylate species on the titania surface was detected but it appears that these are spectator species. DRIFTS experiments under reaction conditions also show the presence of weak, reversible adsorption of CO₂ (near 2340 cm⁻¹) which may be competing with CO for adsorption sites.     

Photochemical Degradation of 1- and 2-methylphenanthrenes in Acetonitrile and on Some Solids

In order to obtain basic information about photochemical degradability and degradation products for 1- and 2-methylphenanthrenes (MPs), photodegradation of these compounds in an organic solvent (acetonitrile) and on some solids (soil, silica gel [SiO₂], and titanium dioxide [TiO₂]) were carried out in a laboratory using solar simulators.

The results showed that the degradation rate (%) increases in the order of TiO₂ > SiO₂ > acetonitrile > soil. Products formed in acetonitrile included aromatic compounds with molecular ion [M⁺] peaks at m/z = 148, 162, 198, 206, 208, 210, 222, 224 and 238. In case of 1 MP, a compound with M⁺ 206, which was identified as 1-phenanthrene-carbaldehyde, was predominantly formed. However, 2MP showed no predominance for M⁺ 206 and also yielded M⁺ 210 and M⁺ 224 as major products. Degradation on soil and SiO₂ gave similar products to those detected in acetonitrile, while that on TiO₂ gave different products from the formers. Based on the results of product analysis, three degradation pathways which may occur in acetonitrile are proposed.     

Preparation of MoO3/TiO2 Catalysts with Eggshell and Uniform Mo Distribution by Water-Assisted Spreading of MoO3

MoO₃/TiO₂ catalysts were prepared by reaction of TiO₂ extrudates (140 m²g⁻¹) with a MoO₃/H₂O slurry. The adsorption of molybdena species was strong; sharp, deep eggshell profiles of the Mo concentration were obtained. The hydrodesulfurization activity of saturated catalysts with a uniform Mo distribution (about 10 wt.% MoO₃) was at least the same as that of a sample prepared by conventional impregnation.     

Electrical properties of V2O5–WO3/TiO2 EUROCAT catalysts evidence for redox process in selective catalytic reduction (SCR) deNOx reaction

Electrical conductivity measurements on EUROCAT V₂O₅–WO₃/TiO₂ catalyst and on its precursor without vanadia were performed at 300°C under pure oxygen to characterize the samples, under NO and under NH₃ to determine the mode of reactivity of these reactants and under two reaction mixtures ((i) 2000 ppm NO + 2000 ppm NH₃ without O₂, and (ii) 2000 ppm NO + 2000 ppm NH₃ + 500 ppm O₂) to put in evidence redox processes in SCR deNO_x reaction.It was first demonstrated that titania support contains certain amounts of dissolved W⁶⁺ and V⁵⁺ ions, whose dissolution in the lattice of titania creates an n-type doping effect. Electrical conductivity revealed that the so-called reference pure titania monolith was highly doped by heterovalent cations whose valency was higher than +4. Subsequent chemical analyses revealed that so-called pure titania reference catalyst was actually the WO₃/TiO₂ precursor of V₂O₅–WO₃/TiO₂ EUROCAT catalyst. It contained an average amount of 0.37 at.% W⁶⁺dissolved in titania, i.e. 1.07 × 10²⁰ W⁶⁺ cations dissolved/cm³ of titania. For the fresh catalyst, the mean amounts of W⁶⁺ and V⁵⁺ ions dissolved in titania were found to be equal to 1.07 × 10²⁰ and 4.47 × 10²⁰ cm⁻³, respectively. For the used catalyst, the mean amounts of W⁶⁺ and V⁵⁺ ions dissolved were found to be equal to 1.07 × 10²⁰ and 7.42 × 10²⁰ cm⁻³, respectively. Since fresh and used catalysts have similar compositions and similar catalytic behaviours, the only manifestation of ageing was a supplementary progressive dissolution of 2.9 × 10²⁰ additional V⁵⁺ cations in titania.After a prompt removal of oxygen, it appeared that NO alone has an electron acceptor character, linked to its possible ionosorption as NO⁻ and to the filling of anionic vacancies, mostly present on vanadia. Ammonia had a strong reducing behaviour with the formation of singly ionized vacancies. A subsequent introduction of NO indicated a donor character of this molecule, in opposition to its first adsorption. This was ascribed to its reaction with previously adsorbed ammonia strongly bound to acidic sites. Under NO + NH₃ reaction mixture in the absence of oxygen, the increase of electrical conductivity was ascribed to the formation of anionic vacancies, mainly on vanadia, created by dehydroxylation and dehydration of the surface. These anionic vacancies were initially subsequently filled by the oxygen atom of NO. N^o atoms, resulting from the dissociation of NO and from ammonia dehydrogenation, recombined into dinitrogen molecules. The reaction corresponded to

Full-size image

. In the presence of oxygen, NO did not exhibit anymore its electron acceptor character, since the filling of anionic vacancies was performed by oxygen from the gas phase. NO reacted directly with ammonia strongly bound on acidic sites. A tentative redox mechanism was proposed for both cases.     

Effects of I and F codoped TiO2 on the photocatalytic degradation of methylene blue

Nanocrystalline I-F-codoped TiO₂ was prepared by a sol-gel-impregnation method, using tetrabutylorthotitanate in a mixed NH₄I-NH₄F aqueous solution. The as-prepared TiO₂ was characterized with UV-vis diffuse reflectance spectra, X-ray diffraction and nitrogen adsorption. The degradation of methylene blue (MB) over as-prepared TiO₂ in aqueous solution under simulated sunlight irradiation was remarkably enhanced by codoping with I and F. The effects of codoping and calcination temperature on the photocatalytic activity and microstructures were investigated. The photocatalytic activity of as-prepared I-F-codoped TiO₂ was remarkably higher than that of pure, I-doped, and F-doped TiO₂ when the molar ratios of I and F to Ti were kept in the value of 10. The influence of I-F-modification on the photocatalytic activity was discussed by considering the higher surface area, entire anatase phase, effective dopant content, and stronger absorbance of sunlight, corresponding to the higher quantum efficiency. In addition to a complete removal of color, the as-prepared TiO₂ was simultaneously able to oxidize MB and small amounts of intermediates such as formic acid and phenol were detected. After prolonged sunlight irradiation some intermediates almost vanished, and MB appeared to be eventually mineralized to NH₄⁺, NO₃⁻ and SO₄²⁻.     

Hydrodesulfurization of Dibenzothiophene Over Ni-Mo Sulfides Supported by Proton-Exchanged Siliceous MCM-41

Strong acid sites on the surface of mesoporous MCM-41 were generated by ion-exchanging siliceous MCM-41 with dilute HNO₃ solution (0.5 M). The XRF determination indicates that most of the sodium cations contained in MCM-41 can be removed by the proton exchange, and dealuminization was observed during the proton exchange. The acidity of the mesoporous materials was characterized by means of NH₃-TPD and the Hammett indicators. It is revealed that new strong acid sites (-5.6 > H₀ > -8.2) were generated after the first 2 h of ion exchange and that the following ion exchanges had little effect on the acidic properties. XRD patterns of the mesoporous materials indicate that the structure of siliceous MCM-41 was improved by HNO₃ ion exchange. When Ni-Mo sulfides were supported on the prepared solid acid (H⁺-MCM-41), high performance in the hydrodesulfurization (HDS) of dibenzothiophene (DBT) was observed. However, the HDS activity was decreased while the selectivity of biphenyl (BP) was increased, when H⁺-Si-MCM-41 was ion exchanged with Na₂CO₃ aqueous solution. TPR profiles of the supported Ni-Mo oxides reveal that the acidic properties of the supports greatly influence the hydrogenation activities of the bimetallic oxides. The high performance of H⁺-MCM-41-supported Ni-Mo catalysts may be attributed to the enhanced hydrogenation activity. The introduction of Na cation into the support led to the decrease of the HDS activity due to the poor hydrogenation ability of the supported bimetallic oxides. The HDS activity is well correlated with the low H₂ consumption temperature in the TPR profiles.     

Photocatalytic degradation of cationic blue X-GRL adsorbed on TiO2/SiO2 photocatalyst

Photocatalytic degradation of cationic blue X-GRL (CBX), a strongly adsorbing substrate on TiO₂/SiO₂, has been investigated by diffuse reflection UV–VIS spectra (UV–visible/DRS) and FT-IR methods. The heterogeneous photocatalysis processes include: adsorption of dye, surface reaction and desorption of final products. The adsorption of CBX onto the surface of TiO₂/SiO₂ was characterized, and the effect of initial pH of solution on the adsorption was determined. The results demonstrated that CBX was strongly adsorbed at the TiO⁻ site of the catalyst by a penta-heterocyclic-N group. The adsorbed CBX was monitored directly by the UV–VIS/DRS technique during the photodegradation. The results confirmed that the surface photodegradation reaction of CBX was predominantly procedure with the mechanism of direct charge transfer from the semiconductor to the dye adsorbed at TiO center, and its reaction followed the pseudo-first-order kinetics. This mechanism resulted in the formation of more aliphatic amines and/or amide byproducts, which were further transformed to NH₄⁺.     

The Effects of Al2O3 Addition and WO3 Modification on Catalytic Activities of NiO/TiO2 for Acid Catalysis

NiO/Al₂O₃–TiO₂/WO₃ catalysts for acid catalysis were prepared by the addition of Al₂O₃ and the modification with WO₃. The strong acid sites were formed through the bonding between dispersed WO₃ and TiO₂. The larger the dispersed WO₃ amount, the higher both the acidity and catalytic activity. The addition of Al₂O₃ up to 5 mol% enhanced acidity and catalytic activity of NiO/Al₂O₃–TiO₂/WO₃ gradually due to the interaction between Al₂O₃ and TiO₂ and consequent formation of Al–O–Ti bond. The presence of NiO may attract reactants and enhance the local concentration of reactants near acid sites and consequently increase catalytic activity.     

Impact of supercritical drying and heat treatment on physical properties of titania/silica aerogel monolithic and its applications

TiO₂–SiO₂ monolithic aerogels were homogeneously prepared using sol–gel method. Critical point of drying of TiO₂–SiO₂ gels with ethanol was studied for 30, 60, 90 and 120 min. Subsequently, the gels were dried with supercritical ethanol, resulting in amorphous aerogels that crystallized following heat treatment at 550 °C from 1 to 5 h. The TiO₂–SiO₂ aerogels were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and surface area measurements. The molar ratio of SiO₂:TiO₂ was 6 and the synthetic strategy revealed that TiO₂–SiO₂ aerogel, had a surface area 868 m²/g, particle size 40 nm, density 0.17 g/cm³ and 80% porosity. The finding indicated that from economic point of view, TiO₂–SiO₂ gel should be supercritical dried for 30 min and heat-treated for 5 h. The TiO₂–SiO₂ aerogel monoliths photocatalyst synthesized using sol–gel method provided insight into the characteristics that make a photocatalyst material well-suited for photodegradation of phenol and cyanide in an industrial waste stream containing Cl⁻, S²⁻ and NH₄⁺. Interestingly, after multiple reuse cycles (i.e. ≥7), photodegradation systems with regenerated photocatalyst showed a slightly decreasing of photoactivity 2–4%. The overall kinetics of photodegradation of either phenol or cyanide using TiO₂–SiO₂ aerogel photocatalyst was found to be of first order.     

Enhanced photocatalytic activity of Ag doped TiO2 nanoparticles synthesized by a microwave assisted method

Pure anatase TiO₂ photocatalyst with different Ag contents was prepared via a controlled and energy efficient microwave assisted method. The prepared material was further characterized by several analytical techniques like X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), surface area measurement (BET), Fourier transform-infrared spectroscopy (FT-IR), diffused reflectance spectroscopy (DRS), and thermogravimetric–differential thermal analysis (TGA–DTA). A 10 nm average crystallite size with nano-crystals of pseudo-cube like morphology was obtained for optimal (0.25 mol%) Ag doped TiO₂. The present research work is mainly focused on the enhancement of degradation efficiency of methyl orange (MO) by doping of Ag in TiO₂ matrix using UV light (365 nm). A 99.5% photodegradation efficiency of methyl orange was achieved by utilizing 0.25 mol% Ag doped TiO₂ (1 g/dm³) at pH=3 within 70 min. Recyclability of photocatalyst was also studied, with the material being found to be stable up to five runs.     

Phorate degradation by TiO2 photocatalysis: Parameter and reaction pathway investigations

The photocatalytic degradation of phorate in aqueous suspensions was examined with the use of titanium dioxide (TiO₂) as a photocatalyst. About 99% of phorate was degraded after UV irradiation for 60 min. The photodegradation of phorate followed pseudo-first-order kinetics and parameters such as pH of the system, TiO₂ dosage, and presence of anions were found to influence the reaction rate. To obtain a better understanding of the mechanistic details of this TiO₂-assisted photodegradation of phorate with UV irradiation, the intermediates of the processes were separated, identified, and characterized by the solid-phase microextraction (SPME) and gas chromatography/mass spectrometry (GC/MS) techniques. The probable photodegradation pathways were proposed and discussed. To the best of our knowledge, this is the first study that reports the degradation pathways of phorate. The electrical energy consumption per order of magnitude for photocatalytic degradation of phorate was also calculated and showed that a moderated efficiency (E_EO = 96 kWh/(m³ order)) was obtained in TiO₂/UV process.